The driver might pull connectors which weren't submitted by
user-space into the atomic state. For instance,
intel_dp_mst_atomic_master_trans_check() pulls in connectors
sharing the same DP-MST stream. However, if the connector is
unregistered, this later fails with:
[ 559.425658] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset] [CONNECTOR:378:DP-7] is not registered
Skip the unregistered connector check to allow user-space to turn
off connectors one-by-one.
See this wlroots issue:
https://gitlab.freedesktop.org/wlroots/wlroots/-/issues/3407
Previous discussion:
https://lore.kernel.org/intel-gfx/Y6GX7z17WmDSKwta@ideak-desk.fi.intel.com/
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231005131623.114379-1-contact@emersion.fr
The sta_himax83102 panel sometimes shows abnormally flickering
horizontal lines. The front gate output will precharge the X point of
the next pole circuit before TP(TouchPanel Enable) term starts, and wait
until the end of the TP term to resume the CLK. For this reason, the X
point must be maintained during the TP term. In abnormal case, we
measured a slight leakage at point X. This because during the TP term,
the GPW does not fully pull the VGL low, causing the TFT to not be
closed tightly.
To fix this, we completely pull GPW to VGL before entering the TP term.
This will ensure that the TFT is closed tightly and prevent the abnormal
display.
Fixes: 1bc2ef065f13 ("drm/panel: Support for Starry-himax83102-j02 TDDI MIPI-DSI panel")
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231007064949.22668-1-zhouruihai@huaqin.corp-partner.google.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231007064949.22668-1-zhouruihai@huaqin.corp-partner.google.com
Since size of 'header' pointer and '*header' structure is equal on 64-bit
machines issue probably didn't cause any wrong behavior. But anyway,
fixing typo is required.
Fixes: 7a73ba7469cb ("drm/vmwgfx: Use TTM handles instead of SIDs as user-space surface handles.")
Co-developed-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com>
Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230905100203.1716731-1-konstantin.meskhidze@huawei.com
When a fence signals there is a very small race window where the timestamp
isn't updated yet. sync_file solves this by busy waiting for the
timestamp to appear, but on other ocassions didn't handled this
correctly.
Provide a dma_fence_timestamp() helper function for this and use it in
all appropriate cases.
Another alternative would be to grab the spinlock when that happens.
v2 by teddy: add a wait parameter to wait for the timestamp to show up, in case
the accurate timestamp is needed and/or the timestamp is not based on
ktime (e.g. hw timestamp)
v3 chk: drop the parameter again for unified handling
Signed-off-by: Yunxiang Li <Yunxiang.Li@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 1774baa64f93 ("drm/scheduler: Change scheduled fence track v2")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20230929104725.2358-1-christian.koenig@amd.com
Report the maximum number of IBs that can be pushed with a single
DRM_IOCTL_NOUVEAU_EXEC through DRM_IOCTL_NOUVEAU_GETPARAM.
While the maximum number of IBs per ring might vary between chipsets,
the kernel will make sure that userspace can only push a fraction of the
maximum number of IBs per ring per job, such that we avoid a situation
where there's only a single job occupying the ring, which could
potentially lead to the ring run dry.
Using DRM_IOCTL_NOUVEAU_GETPARAM to report the maximum number of IBs
that can be pushed with a single DRM_IOCTL_NOUVEAU_EXEC implies that
all channels of a given device have the same ring size.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231002135008.10651-3-dakr@redhat.com
The One Mix 2S is a mini laptop with a 1200x1920 portrait screen
mounted in a landscape oriented clamshell case. Because of the too
generic DMI strings this entry is also doing bios-date matching.
Signed-off-by: Kai Uwe Broulik <foss-linux@broulik.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001114710.336172-1-foss-linux@broulik.de
The kunit_action_platform_driver_unregister is added with
&fake_platform_driver as ctx, but the kunit_release_action is called
pdev as ctx. Fix that by replacing it with &fake_platform_driver.
Fixes: 4f2b0b583baa ("drm/tests: helpers: Switch to kunit actions")
Signed-off-by: Arthur Grillo <arthurgrillo@riseup.net>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920-kunit-kasan-fixes-v1-1-1a0fc261832d@riseup.net
The removed line prevents the following cleanup function
to execute a dma_fence_put on the out_fence to free its
memory, producing the following output in kmemleak:
unreferenced object 0xffff888126d8ee00 (size 128):
comm "kwin_wayland", pid 981, jiffies 4295380296 (age 390.060s)
hex dump (first 32 bytes):
c8 a1 c2 27 81 88 ff ff e0 14 a9 c0 ff ff ff ff ...'............
30 1a e1 2e a6 00 00 00 28 fc 5b 17 81 88 ff ff 0.......(.[.....
backtrace:
[<0000000011655661>] kmalloc_trace+0x26/0xa0
[<0000000055f15b82>] virtio_gpu_fence_alloc+0x47/0xc0 [virtio_gpu]
[<00000000fa6d96f9>] virtio_gpu_execbuffer_ioctl+0x1a8/0x800 [virtio_gpu]
[<00000000e6cb5105>] drm_ioctl_kernel+0x169/0x240 [drm]
[<000000005ad33e27>] drm_ioctl+0x399/0x6b0 [drm]
[<00000000a19dbf65>] __x64_sys_ioctl+0xc5/0x100
[<0000000011fa801e>] do_syscall_64+0x5b/0xc0
[<0000000065c76d8a>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
unreferenced object 0xffff888121930500 (size 128):
comm "kwin_wayland", pid 981, jiffies 4295380313 (age 390.096s)
hex dump (first 32 bytes):
c8 a1 c2 27 81 88 ff ff e0 14 a9 c0 ff ff ff ff ...'............
f9 ec d7 2f a6 00 00 00 28 fc 5b 17 81 88 ff ff .../....(.[.....
backtrace:
[<0000000011655661>] kmalloc_trace+0x26/0xa0
[<0000000055f15b82>] virtio_gpu_fence_alloc+0x47/0xc0 [virtio_gpu]
[<00000000fa6d96f9>] virtio_gpu_execbuffer_ioctl+0x1a8/0x800 [virtio_gpu]
[<00000000e6cb5105>] drm_ioctl_kernel+0x169/0x240 [drm]
[<000000005ad33e27>] drm_ioctl+0x399/0x6b0 [drm]
[<00000000a19dbf65>] __x64_sys_ioctl+0xc5/0x100
[<0000000011fa801e>] do_syscall_64+0x5b/0xc0
[<0000000065c76d8a>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[...]
This memleak will grow quickly, being possible to see the
following line in dmesg after few minutes of life in the
virtual machine:
[ 706.217388] kmemleak: 10731 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
The patch will remove the line to allow the cleanup
function do its job.
Signed-off-by: José Pekkarinen <jose.pekkarinen@foxhound.fi>
Fixes: e4812ab8e6b1 ("drm/virtio: Refactor and optimize job submission code path")
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230912060824.5210-1-jose.pekkarinen@foxhound.fi
The u_memcpya() function is supposed to return error pointers on
error. Returning NULL will lead to an Oops.
Fixes: e3885f712134 ("nouveau/u_memcpya: use vmemdup_user")
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/10fd258b-466f-4c5b-9d48-fe61a3f21424@moroto.mountain
I think there are limit checks in place for most things but the
new uAPI wants to not have them.
Add a limit check and use the vmemdup_user helper instead.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230810185020.231135-1-airlied@gmail.com
Always stop and re-start the scheduler in order to let the scheduler
free up the timedout job in case it got signaled. In case of exec jobs
the job type specific callback will take care to signal all fences and
tear down the channel.
Fixes: b88baab82871 ("drm/nouveau: implement new VM_BIND uAPI")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230916162835.5719-1-dakr@redhat.com
Fix the following warning.
drivers/gpu/drm/nouveau/nouveau_fence.c:210:45: sparse: sparse:
incorrect type in initializer (different address spaces)
@@ expected struct nouveau_channel *chan
@@ got struct nouveau_channel [noderef] __rcu *channel
We're just about to emit the fence, there is nothing to protect against
yet, hence it is safe to just cast __rcu away.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309140340.BwKXzaDx-lkp@intel.com/
Fixes: 978474dc8278 ("drm/nouveau: fence: fix undefined fence state after emit")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230916011501.15813-1-dakr@redhat.com
As a result of the recent Kconfig reworks, the default settings for the
framebuffer interfaces changed in unexpected ways:
Configurations that leave CONFIG_FB disabled but use DRM now get
DRM_FBDEV_EMULATION by default. This also turns on the deprecated /dev/fb
device nodes for machines that don't actually want it.
In turn, configurations that previously had DRM_FBDEV_EMULATION enabled
now only get the /dev/fb front-end but not the more useful framebuffer
console, which is not selected any more.
We had previously decided that any combination of the three frontends
(FB_DEVICE, FRAMEBUFFER_CONSOLE and LOGO) should be selectable, but the
new default settings mean that a lot of defconfig files would have to
get adapted.
Change the defaults back to what they were in Linux 6.5:
- Leave DRM_FBDEV_EMULATION turned off unless CONFIG_FB
is enabled. Previously this was a hard dependency but now the two are
independent. However, configurations that enable CONFIG_FB probably
also want to keep the emulation for DRM, while those without FB
presumably did that intentionally in the past.
- Leave FB_DEVICE turned off for FB=n. Following the same
logic, the deprecated option should not automatically get enabled
here, most users that had FB turned off in the past do not want it,
even if they want the console
- Turn the FRAMEBUFFER_CONSOLE option on if
DRM_FBDEV_EMULATION is set to avoid having to change defconfig
files that relied on it being selected unconditionally in the past.
This also makes sense since both LOGO and FB_DEVICE are now disabled
by default for builds without CONFIG_FB, but DRM_FBDEV_EMULATION
would make no sense if all three are disabled.
Fixes: a5ae331edb02b ("drm: Drop select FRAMEBUFFER_CONSOLE for DRM_FBDEV_EMULATION")
Fixes: 701d2054fa317 ("fbdev: Make support for userspace interfaces configurable")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230911205338.2385278-1-arnd@kernel.org
While drm_mm test was converted form igt selftest to kunit, unexpected
value of "end" argument equal "start" was introduced to one of calls to a
function that executes the drm_test_mm_insert_range for specific start/end
pair of arguments. As a consequence, DRM_MM_BUG_ON(end <= start) is
triggered. Fix it by restoring the original value.
Fixes: fc8d29e298cf ("drm: selftest: convert drm_mm selftest to KUnit")
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: "Maíra Canal" <mairacanal@riseup.net>
Cc: Arthur Grillo <arthurgrillo@riseup.net>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Daniel Latypov <dlatypov@google.com>
Cc: stable@vger.kernel.org # v6.1+
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230911130323.7037-2-janusz.krzysztofik@linux.intel.com
Add CI integration support files for drm subsystem to gitlab.freedesktop.org instance.
-----BEGIN PGP SIGNATURE-----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=X1RZ
-----END PGP SIGNATURE-----
Merge tag 'topic/drm-ci-2023-08-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm ci scripts from Dave Airlie:
"This is a bunch of ci integration for the freedesktop gitlab instance
where we currently do upstream userspace testing on diverse sets of
GPU hardware. From my perspective I think it's an experiment worth
going with and seeing how the benefits/noise playout keeping these
files useful.
Ideally I'd like to get this so we can do pre-merge testing on PRs
eventually.
Below is some info from danvet on why we've ended up making the
decision and how we can roll it back if we decide it was a bad plan.
Why in upstream?
- like documentation, testcases, tools CI integration is one of these
things where you can waste endless amounts of time if you
accidentally have a version that doesn't match your source code
- but also like the above, there's a balance, this is the initial cut
of what we think makes sense to keep in sync vs out-of-tree,
probably needs adjustment
- gitlab supports out-of-repo gitlab integration and that's what's
been used for the kernel in drm, but it results in per-driver
fragmentation and lots of duplicated effort. the simple act of
smashing an arbitrary winner into a topic branch already started
surfacing patches on dri-devel and sparking good cross driver team
discussions
Why gitlab?
- it's not any more shit than any of the other CI
- drm userspace uses it extensively for everything in userspace, we
have a lot of people and experience with this, including
integration of hw testing labs
- media userspace like gstreamer is also on gitlab.fd.o, and there's
discussion to extend this to the media subsystem in some fashion
Can this be shared?
- there's definitely a pile of code that could move to scripts/ if
other subsystem adopt ci integration in upstream kernel git. other
bits are more drm/gpu specific like the igt-gpu-tests/tools
integration
- docker images can be run locally or in other CI runners
Will we regret this?
- it's all in one directory, intentionally, for easy deletion
- probably 1-2 years in upstream to see whether this is worth it or a
Big Mistake. that's roughly what it took to _really_ roll out solid
CI in the bigger userspace projects we have on gitlab.fd.o like
mesa3d"
* tag 'topic/drm-ci-2023-08-31-1' of git://anongit.freedesktop.org/drm/drm:
drm: ci: docs: fix build warning - add missing escape
drm: Add initial ci/ subdirectory
* Clean up vCPU targets, always returning generic v8 as the preferred target
* Trap forwarding infrastructure for nested virtualization (used for traps
that are taken from an L2 guest and are needed by the L1 hypervisor)
* FEAT_TLBIRANGE support to only invalidate specific ranges of addresses
when collapsing a table PTE to a block PTE. This avoids that the guest
refills the TLBs again for addresses that aren't covered by the table PTE.
* Fix vPMU issues related to handling of PMUver.
* Don't unnecessary align non-stack allocations in the EL2 VA space
* Drop HCR_VIRT_EXCP_MASK, which was never used...
* Don't use smp_processor_id() in kvm_arch_vcpu_load(),
but the cpu parameter instead
* Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort()
* Remove prototypes without implementations
RISC-V:
* Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest
* Added ONE_REG interface for SATP mode
* Added ONE_REG interface to enable/disable multiple ISA extensions
* Improved error codes returned by ONE_REG interfaces
* Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V
* Added get-reg-list selftest for KVM RISC-V
s390:
* PV crypto passthrough enablement (Tony, Steffen, Viktor, Janosch)
Allows a PV guest to use crypto cards. Card access is governed by
the firmware and once a crypto queue is "bound" to a PV VM every
other entity (PV or not) looses access until it is not bound
anymore. Enablement is done via flags when creating the PV VM.
* Guest debug fixes (Ilya)
x86:
* Clean up KVM's handling of Intel architectural events
* Intel bugfixes
* Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use debug
registers and generate/handle #DBs
* Clean up LBR virtualization code
* Fix a bug where KVM fails to set the target pCPU during an IRTE update
* Fix fatal bugs in SEV-ES intrahost migration
* Fix a bug where the recent (architecturally correct) change to reinject
#BP and skip INT3 broke SEV guests (can't decode INT3 to skip it)
* Retry APIC map recalculation if a vCPU is added/enabled
* Overhaul emergency reboot code to bring SVM up to par with VMX, tie the
"emergency disabling" behavior to KVM actually being loaded, and move all of
the logic within KVM
* Fix user triggerable WARNs in SVM where KVM incorrectly assumes the TSC
ratio MSR cannot diverge from the default when TSC scaling is disabled
up related code
* Add a framework to allow "caching" feature flags so that KVM can check if
the guest can use a feature without needing to search guest CPUID
* Rip out the ancient MMU_DEBUG crud and replace the useful bits with
CONFIG_KVM_PROVE_MMU
* Fix KVM's handling of !visible guest roots to avoid premature triple fault
injection
* Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the API surface
that is needed by external users (currently only KVMGT), and fix a variety
of issues in the process
This last item had a silly one-character bug in the topic branch that
was sent to me. Because it caused pretty bad selftest failures in
some configurations, I decided to squash in the fix. So, while the
exact commit ids haven't been in linux-next, the code has (from the
kvm-x86 tree).
Generic:
* Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier events to pass
action specific data without needing to constantly update the main handlers.
* Drop unused function declarations
Selftests:
* Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs
* Add support for printf() in guest code and covert all guest asserts to use
printf-based reporting
* Clean up the PMU event filter test and add new testcases
* Include x86 selftests in the KVM x86 MAINTAINERS entry
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmT1m0kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMNgggAiN7nz6UC423FznuI+yO3TLm8tkx1
CpKh5onqQogVtchH+vrngi97cfOzZb1/AtifY90OWQi31KEWhehkeofcx7G6ERhj
5a9NFADY1xGBsX4exca/VHDxhnzsbDWaWYPXw5vWFWI6erft9Mvy3tp1LwTvOzqM
v8X4aWz+g5bmo/DWJf4Wu32tEU6mnxzkrjKU14JmyqQTBawVmJ3RYvHVJ/Agpw+n
hRtPAy7FU6XTdkmq/uCT+KUHuJEIK0E/l1js47HFAqSzwdW70UDg14GGo1o4ETxu
RjZQmVNvL57yVgi6QU38/A0FWIsWQm5IlaX1Ug6x8pjZPnUKNbo9BY4T1g==
=W+4p
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- Clean up vCPU targets, always returning generic v8 as the preferred
target
- Trap forwarding infrastructure for nested virtualization (used for
traps that are taken from an L2 guest and are needed by the L1
hypervisor)
- FEAT_TLBIRANGE support to only invalidate specific ranges of
addresses when collapsing a table PTE to a block PTE. This avoids
that the guest refills the TLBs again for addresses that aren't
covered by the table PTE.
- Fix vPMU issues related to handling of PMUver.
- Don't unnecessary align non-stack allocations in the EL2 VA space
- Drop HCR_VIRT_EXCP_MASK, which was never used...
- Don't use smp_processor_id() in kvm_arch_vcpu_load(), but the cpu
parameter instead
- Drop redundant call to kvm_set_pfn_accessed() in user_mem_abort()
- Remove prototypes without implementations
RISC-V:
- Zba, Zbs, Zicntr, Zicsr, Zifencei, and Zihpm support for guest
- Added ONE_REG interface for SATP mode
- Added ONE_REG interface to enable/disable multiple ISA extensions
- Improved error codes returned by ONE_REG interfaces
- Added KVM_GET_REG_LIST ioctl() implementation for KVM RISC-V
- Added get-reg-list selftest for KVM RISC-V
s390:
- PV crypto passthrough enablement (Tony, Steffen, Viktor, Janosch)
Allows a PV guest to use crypto cards. Card access is governed by
the firmware and once a crypto queue is "bound" to a PV VM every
other entity (PV or not) looses access until it is not bound
anymore. Enablement is done via flags when creating the PV VM.
- Guest debug fixes (Ilya)
x86:
- Clean up KVM's handling of Intel architectural events
- Intel bugfixes
- Add support for SEV-ES DebugSwap, allowing SEV-ES guests to use
debug registers and generate/handle #DBs
- Clean up LBR virtualization code
- Fix a bug where KVM fails to set the target pCPU during an IRTE
update
- Fix fatal bugs in SEV-ES intrahost migration
- Fix a bug where the recent (architecturally correct) change to
reinject #BP and skip INT3 broke SEV guests (can't decode INT3 to
skip it)
- Retry APIC map recalculation if a vCPU is added/enabled
- Overhaul emergency reboot code to bring SVM up to par with VMX, tie
the "emergency disabling" behavior to KVM actually being loaded,
and move all of the logic within KVM
- Fix user triggerable WARNs in SVM where KVM incorrectly assumes the
TSC ratio MSR cannot diverge from the default when TSC scaling is
disabled up related code
- Add a framework to allow "caching" feature flags so that KVM can
check if the guest can use a feature without needing to search
guest CPUID
- Rip out the ancient MMU_DEBUG crud and replace the useful bits with
CONFIG_KVM_PROVE_MMU
- Fix KVM's handling of !visible guest roots to avoid premature
triple fault injection
- Overhaul KVM's page-track APIs, and KVMGT's usage, to reduce the
API surface that is needed by external users (currently only
KVMGT), and fix a variety of issues in the process
Generic:
- Wrap kvm_{gfn,hva}_range.pte in a union to allow mmu_notifier
events to pass action specific data without needing to constantly
update the main handlers.
- Drop unused function declarations
Selftests:
- Add testcases to x86's sync_regs_test for detecting KVM TOCTOU bugs
- Add support for printf() in guest code and covert all guest asserts
to use printf-based reporting
- Clean up the PMU event filter test and add new testcases
- Include x86 selftests in the KVM x86 MAINTAINERS entry"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (279 commits)
KVM: x86/mmu: Include mmu.h in spte.h
KVM: x86/mmu: Use dummy root, backed by zero page, for !visible guest roots
KVM: x86/mmu: Disallow guest from using !visible slots for page tables
KVM: x86/mmu: Harden TDP MMU iteration against root w/o shadow page
KVM: x86/mmu: Harden new PGD against roots without shadow pages
KVM: x86/mmu: Add helper to convert root hpa to shadow page
drm/i915/gvt: Drop final dependencies on KVM internal details
KVM: x86/mmu: Handle KVM bookkeeping in page-track APIs, not callers
KVM: x86/mmu: Drop @slot param from exported/external page-track APIs
KVM: x86/mmu: Bug the VM if write-tracking is used but not enabled
KVM: x86/mmu: Assert that correct locks are held for page write-tracking
KVM: x86/mmu: Rename page-track APIs to reflect the new reality
KVM: x86/mmu: Drop infrastructure for multiple page-track modes
KVM: x86/mmu: Use page-track notifiers iff there are external users
KVM: x86/mmu: Move KVM-only page-track declarations to internal header
KVM: x86: Remove the unused page-track hook track_flush_slot()
drm/i915/gvt: switch from ->track_flush_slot() to ->track_remove_region()
KVM: x86: Add a new page-track hook to handle memslot deletion
drm/i915/gvt: Don't bother removing write-protection on to-be-deleted slot
KVM: x86: Reject memslot MOVE operations if KVMGT is attached
...
Commit 254986e324ad ("drm/radeon: Use the drm suballocation manager implementation.")
made the fence wait in amdgpu_sa_bo_new() interruptible but there is no
code to handle an interrupt. This caused the kernel to randomly explode
in high-VRAM-pressure situations so make it uninterruptible again.
Fixes: 254986e324ad ("drm/radeon: Use the drm suballocation manager implementation.")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2769
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org # 6.4+
CC: Simon Pilkington <simonp.git@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906195517.1345717-1-alexander.deucher@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
If *any* object of a certain WW mutex class is locked, lockdep will
consider *all* mutexes of that class as locked. Also the lock allocation
tracking code will apparently register only the address of the first
mutex of a given class locked in a sequence.
This has the odd consequence that if that first mutex is unlocked while
other mutexes of the same class remain locked and then its memory then
freed, the lock alloc tracking code will incorrectly assume that memory
is freed with a held lock in there.
For now, work around that for drm_exec by releasing the first grabbed
object lock last.
v2:
- Fix a typo (Danilo Krummrich)
- Reword the commit message a bit.
- Add a Fixes: tag
Related lock alloc tracking warning:
[ 322.660067] =========================
[ 322.660070] WARNING: held lock freed!
[ 322.660074] 6.5.0-rc7+ #155 Tainted: G U N
[ 322.660078] -------------------------
[ 322.660081] kunit_try_catch/4981 is freeing memory ffff888112adc000-ffff888112adc3ff, with a lock still held there!
[ 322.660089] ffff888112adc1a0 (reservation_ww_class_mutex){+.+.}-{3:3}, at: drm_exec_lock_obj+0x11a/0x600 [drm_exec]
[ 322.660104] 2 locks held by kunit_try_catch/4981:
[ 322.660108] #0: ffffc9000343fe18 (reservation_ww_class_acquire){+.+.}-{0:0}, at: test_early_put+0x22f/0x490 [drm_exec_test]
[ 322.660123] #1: ffff888112adc1a0 (reservation_ww_class_mutex){+.+.}-{3:3}, at: drm_exec_lock_obj+0x11a/0x600 [drm_exec]
[ 322.660135]
stack backtrace:
[ 322.660139] CPU: 7 PID: 4981 Comm: kunit_try_catch Tainted: G U N 6.5.0-rc7+ #155
[ 322.660146] Hardware name: ASUS System Product Name/PRIME B560M-A AC, BIOS 0403 01/26/2021
[ 322.660152] Call Trace:
[ 322.660155] <TASK>
[ 322.660158] dump_stack_lvl+0x57/0x90
[ 322.660164] debug_check_no_locks_freed+0x20b/0x2b0
[ 322.660172] slab_free_freelist_hook+0xa1/0x160
[ 322.660179] ? drm_exec_unlock_all+0x168/0x2a0 [drm_exec]
[ 322.660186] __kmem_cache_free+0xb2/0x290
[ 322.660192] drm_exec_unlock_all+0x168/0x2a0 [drm_exec]
[ 322.660200] drm_exec_fini+0xf/0x1c0 [drm_exec]
[ 322.660206] test_early_put+0x289/0x490 [drm_exec_test]
[ 322.660215] ? __pfx_test_early_put+0x10/0x10 [drm_exec_test]
[ 322.660222] ? __kasan_check_byte+0xf/0x40
[ 322.660227] ? __ksize+0x63/0x140
[ 322.660233] ? drmm_add_final_kfree+0x3e/0xa0 [drm]
[ 322.660289] ? _raw_spin_unlock_irqrestore+0x30/0x60
[ 322.660294] ? lockdep_hardirqs_on+0x7d/0x100
[ 322.660301] ? __pfx_kunit_try_run_case+0x10/0x10 [kunit]
[ 322.660310] ? __pfx_kunit_generic_run_threadfn_adapter+0x10/0x10 [kunit]
[ 322.660319] kunit_generic_run_threadfn_adapter+0x4a/0x90 [kunit]
[ 322.660328] kthread+0x2e7/0x3c0
[ 322.660334] ? __pfx_kthread+0x10/0x10
[ 322.660339] ret_from_fork+0x2d/0x70
[ 322.660345] ? __pfx_kthread+0x10/0x10
[ 322.660349] ret_from_fork_asm+0x1b/0x30
[ 322.660358] </TASK>
[ 322.660818] ok 8 test_early_put
Cc: Christian König <christian.koenig@amd.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Fixes: 09593216bff1 ("drm: execution context for GEM buffers v7")
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230906095039.3320-4-thomas.hellstrom@linux.intel.com
Restrict the wait for boot loader steady state only to SMUv13.0.6. For
older SOCs, ASIC init has a longer wait period and that takes care.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two places in apply_below_the_range() where it's possible for
a divide by zero error to occur. So, to fix this make sure the divisor
is non-zero before attempting the computation in both cases.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2637
Fixes: a463b263032f ("drm/amd/display: Fix frames_to_insert math")
Fixes: ded6119e825a ("drm/amd/display: Reinstate LFC optimization")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DRM legacy gamma, AMD display manager applies implicit sRGB degamma
using a pre-defined sRGB transfer function. It works fine for DCN2
family where degamma ROM and custom curves go to the same color block.
But, on DCN3+, degamma is split into two blocks: degamma ROM for
pre-defined TFs and `gamma correction` for user/custom curves and
degamma ROM settings doesn't apply to cursor plane. To get DRM legacy
gamma working as expected, enable cursor degamma ROM for implict sRGB
degamma on HW with this configuration.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2803
Fixes: 96b020e2163f ("drm/amd/display: check attr flag before set cursor degamma on DCN3+")
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since, calling dcn20_adjust_freesync_v_startup() on DCN3.1+ ASICs
can cause the display to flicker and underflow to occur, we shouldn't
call it for them. So, ensure that the DCN version is less than
DCN_VERSION_3_1 before calling dcn20_adjust_freesync_v_startup().
Cc: stable@vger.kernel.org
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3a31e8b89b7240d9a17ace8a1ed050bdcb560f9e.
We still need to call dcn20_adjust_freesync_v_startup() for older DCN3+
ASICs. Otherwise, it can cause DP to HDMI 2.1 PCONs to fail to light up.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2809
Reviewed-by: Fangzhi Zuo <jerry.zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The timeout arg of usb_bulk_msg() is ms already, which has been converted
to jiffies by msecs_to_jiffies() in usb_start_wait_urb(). So fix the usage
by removing the redundant msecs_to_jiffies() in the macros.
And as Hans suggested, also remove msecs_to_jiffies() for the IDLE_TIMEOUT
macro to make it consistent here and so change IDLE_TIMEOUT to
msecs_to_jiffies(IDLE_TIMEOUT) where it is used.
Fixes: e4f86e437164 ("drm: Add Grain Media GM12U320 driver v2")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230904021421.1663892-1-ruanjinjie@huawei.com
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
Commit c103a23f2f29
("drm/amd: Convert amdgpu to use suballocation helper.")
made the fence wait in amdgpu_sa_bo_new() interruptible but there is no
code to handle an interrupt. This caused the kernel to randomly explode
in high-VRAM-pressure situations so make it uninterruptible again.
Signed-off-by: Simon Pilkington <simonp.git@gmail.com>
Fixes: c103a23f2f29 ("drm/amd: Convert amdgpu to use suballocation helper.")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2761
CC: stable@vger.kernel.org # 6.4+
The offset is just 32bits here so this can potentially overflow if
somebody specifies a large value. Instead reduce the size to calculate
the last possible offset.
The error handling path incorrectly drops the reference to the user
fence BO resulting in potential reference count underflow.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit e2066eb4efe0e7d2d329d6e6765ed637a523ac45.
The problematic IGT test case (i.e. kms_atomic@plane-immutable-zpos) has
been fixed as of commit cb77add45011 ("tests/kms_atomic: remove zpos <
N-planes assert") to the IGT repo. So, reintroduce the reverted code.
Link: cb77add450
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mqd_stride function was introduced in commit 2f77b9a242a2
("drm/amdkfd: Update MQD management on multi XCC setup")
but not assigned for gfx11. Fixes a NULL dereference in debugfs.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.5.x
Do not access the pointer for ras input cmd buffer
if it is even not allocated.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
XCP partitions should not be visible for the VF for GFXIP 9.4.3.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of using direct update, avoid touching unrelated fields.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Interrupt sq data bits were not taken properly from contextid0 and contextid1.
Use macro KFD_CONTEXT_ID_GET_SQ_INT_DATA instead.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During a GPU reset, a normal memory reclaim could block to reclaim
memory. Giving that coredump is a best effort mechanism, it shouldn't
disturb the reset path. Change its memory allocation flag to a
nonblocking one.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver queries umc_info v4_0 to identify ecc cap
for aqua_vanjaram
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Candice Li <candice.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To be used by aqua_vanjaram
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Candice Li <candice.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ODM power optimization is only supported with single stream. When ODM
power optimization is enabled, we might not have enough free pipes for
enabling other stream. So when we are committing more than 1 stream we
should first switch off ODM power optimization to make room for new
stream and then allocating pipe resource for the new stream.
Cc: stable@vger.kernel.org
Fixes: 59de751e3845 ("drm/amd/display: add ODM case when looking for first split pipe")
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We wait for mpc idle while in a locked state, leading to potential
deadlock.
[What]
Move the wait_for_idle call to outside of HW lock. This and a
call to wait_drr_doublebuffer_pending_clear are moved added to a new
static helper function called wait_for_outstanding_hw_updates, to make
the interface clearer.
Cc: stable@vger.kernel.org
Fixes: 8f0d304d21b3 ("drm/amd/display: Do not commit pipe when updating DRR")
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we are dynamically adding new ODM slices, we didn't update
blank state, if the pipe used by new ODM slice is previously blanked,
we will continue outputting blank pixel data on that slice causing
right half of the screen showing blank image.
The previous fix was a temporary hack to directly update current state
when committing new state. This could potentially cause hw and sw
state synchronization issues and it is not permitted by dc commit
design.
Cc: stable@vger.kernel.org
Fixes: 7fbf451e7639 ("drm/amd/display: Reinit DPG when exiting dynamic ODM")
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
