platform-imxdi_rtc.c is only used by mx25, so it can safely go away now that
mx25 has been converted to dt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx25 has been converted to a dt-only platform, we do not need the "mx25.h"
header file anymore.
Remove it and also clean up all the mx25 occurences from the platform helper
code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We use dynamic memory mapping when using dt, so remove all the static mappings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We should use dt to retrieve the IIM base address.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx25_clocks_init() is only used to register the clocks for non-dt platforms.
As mx25 has been converted to a dt-only platform, we can safely remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Depend the MXC debug board on machines which actually support it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx25 is a dt-only platform, we can get rid of platform code support files,
which are unused now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As there is no more mx25 board files, we can turn mx25 into a dt-only platform.
Rename imx25-dt.c to mach-imx25.c to be consistent with the other i.MX SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
eukrea mx25 is well supported in device tree, so let's get rid of its board
files.
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
When generic pm domain support is enabled, the PGC can be used
to completely gate power to the PU power domain containing GPU3D,
GPU2D, and VPU cores.
This code triggers the PGC powerdown sequence to disable the GPU/VPU
isolation cells and gate power and then disables the PU regulator.
To reenable, the reverse powerup sequence is triggered after the PU
regulator is enabled again.
The GPU and VPU devices in the PU power domain temporarily need
to be clocked during powerup, so that the reset machinery can work.
[Avoid explicit regulator enabling in probe, unless !PM]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx25-pdk.dts provides a more complete support than the board file version, so
let's get rid of the board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use "This enables" in the Kconfig help text to fix grammar.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also fix all machine files to make use of it and while at it also make
the pad lists __initconst.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CG8 field of the CCM CCGR3 register is the 'mipi_core_cfg' gate clock,
according to the i.MX6q/sdl reference manuals. This clock is actually the
gate for several clocks, including the ipg clock's output. The MIPI DSI host
controller embedded in the i.MX6q/sdl SoCs takes the ipg clock as the pclk -
the APB clock signal . In order to gate/ungate the ipg clock, this patch adds
a new shared clock gate named as "mipi_ipg".
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CG8 field of the CCM CCGR3 register is named as 'mipi_core_cfg' clock,
according to the i.MX6q/sdl reference manuals. This clock is actually the
gate for several clocks, including the hsi_tx_sel clock's output and the
video_27m clock's output. The MIPI DSI host controller embedded in the
i.MX6q/sdl SoCs uses the video_27m clock to generate PLL reference clock and
MIPI core configuration clock. In order to gate/ungate the two MIPI DSI
host controller relevant clocks, this patch adds the mipi_core_cfg clock as
a shared clock gate.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CG8 field of the CCM CCGR3 register is named as 'mipi_core_cfg'
clock, according to the i.MX6q/sdl reference manuals. This clock is
actually the gate for several clocks, including the hsi_tx_sel clock's
output and the video_27m clock's output. So, this patch changes the
hsi_tx clock to be a shared clock gate.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to the table 33-1 in the i.MX6Q reference manual, the hdmi_isfr
clock's parent should be the video_27m clock. The i.MX6DL reference manual
has the same statement. This patch changes the hdmi_isfr clock's parent
from the pll3_pfd1_540m clock to the video_27m clock.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch supports the video_27m clock which is a fixed factor
clock of the pll3_pfd1_540m clock.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Vybrid SoC has only one Cortex-A5 core and hence should select
the SMP_ON_UP configuration on a SMP kernel.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const structs in arch/arm as const, too.
While at it also add some __initconst annotations.
Acked-by: Jason Cooper <jason@lakedameon.net>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New and updated SoC support. Also included are some cleanups where the
platform maintainers hadn't separated cleanups from new developent in
separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might start
combining the cleanup and new-development branches more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=szd9
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
imx6q_opp_check_speed_grading() remaps memory to the base variable and
never unmaps it. I can't see how this can be of any use later so here I
unmap it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for clock gating of the SNVS peripheral.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for clock gating of UART4 and UART5.
We use these UART's in a (not yet mainlined)
device tree.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As the result of commit b82b6cca4880 ("cpuidle: Invert
CPUIDLE_FLAG_TIME_VALID logic"), the flag gets removed and hence we see
the compile error below.
CC arch/arm/mach-imx/cpuidle-imx6sx.o
arch/arm/mach-imx/cpuidle-imx6sx.c:69:13: error: ‘CPUIDLE_FLAG_TIME_VALID’ undeclared here (not in a function)
Since the behavior of the original flag has been the default, we can
simply drop the flag now.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch introduces an independent cpuidle driver for
i.MX6SX, and supports arm power off in idle, totally
3 levels of cpuidle are supported as below:
1. ARM WFI;
2. SOC in WAIT mode;
3. SOC in WAIT mode + ARM power off.
ARM power off can save at least 5mW power.
This patch also replaces imx6q_enable_rbc with imx6_enable_rbc.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now we support DSM in OCRAM for all i.MX6 SoCs,
the resume entry point is set in asm code of
suspend-imx6.S, so no need to set the resume
entry point for SRC in pre-suspend flow.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For those clk gates which hold share count, since its is_enabled
callback is only checking the share count rather than reading
the hardware register setting, in the late phase of kernel bootup,
the clk_disable_unused action will NOT handle the scenario of
share_count is 0 but the hardware setting is enabled, actually,
U-Boot normally enables all clk gates, then those shared clk gates
will be always enabled until they are used by some modules.
So the problem would be: when kernel boot up, the usecount cat
from clk tree is 0, but the clk gates actually is enabled in
hardware register, it will confuse user and bring unnecessary power
consumption.
This patch adds .disable_unused callback and using hardware register
check for .is_enabled callback of shared nodes to handle such scenario
in late phase of kernel boot up, then the hardware status will match the
clk tree info.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add shift capabilties for the frequency multiplier (DIV_SELECT) to
support Vybrid's USB PLL oddity. The PLL3 and PLL7 are the only
PLL control registers which have the DIV_SELECT bit shifted by
one. Be aware, there are known documentation errors in the
reference manual too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Vybrid SoC family (in the kernel known as vf610) is a familiy
of multiple similar SoC's. The VF5xx series comes without secondary
Cortex-M4 core, while the second number VFx1x indicates the presence
of a L2 cache controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The post dividers do not work on i.MX6Q rev T0 1.0 so they must be fixed
to 1. As the table index was wrong, a divider a of 4 could still be
requested which implied the clock not to be set properly. This is the
root cause of the HDMI not working at high resolution on rev T0 1.0 of
the SoC.
Signed-off-by: Gary Bisson <bisson.gary@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
* Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one
SoC at a time. For 3.19, the r8a7791 platform and associated\
"Koelsch" board are considered complete and we remove the non-DT
non-multiplatform support for this.
* The ARM Versatile Express has supported DT and multiplatform
for a long time, but we have still kept the legacy board files
around, because not all drivers were fully working before. We
have finally taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches
or just unrelated to the more interesting changes:
* The dts files for arm64 get moved into per-vendor directories for
a clearer structure.
* Some dead code removal (zynq, exynos, davinci, imx)
* Using pr_*() macros more consistently instead of printk(KERN_*)
in some platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Apdh
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been
doing the work de-facto by himself recently is now the
only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the
newly merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for
later rework (the current code is wrong in a harmless way), on
Tegra regression and one samsung spelling fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVIcj22CrR//JCVInAQJyXg/9EPrOpgNBpcCE2pfprc2JmoBqM11C8IDX
1qCP1hMbIhqfgWpoR3DptmiDpUpck5Fwn8L7M1+bIxVvSK0AAgD0n5hQI/GnmeN5
qk2jdAoUlz7tIADb3/1Yc2X8D6ZiYLakhzyi0LVcWfmsmgW1E+bcbuS4XG9RMccR
6gzuqkZqLSzneiKLN3Dqwela8Q3gHYSMFTETFaRxu7gvPkYgc622ePGvGafD7i+u
MYs/sfPwsfuNFMQ/fsdmpGQxNFghwb8Cg0VaEkSBztjV2WiDBD0GMo4Ww5UNr8e7
LvHcoHiYjtnbXHW/b5L5Uswk8BCtWp2udgDHigEbZvj2BfmMlq+qXJ72BwmQb0Nf
ow2R67yOiZ2HhG+776OcMI2BpeY6D0jFcHSNjc2Q14tgns3bhfP23taDb5rFJ8G1
5aCHoACTL6X7TkX9W2iwZ5/KWW+Ftx2ardbdzCHWtjTlD/KaK624YRWeXlLASsE1
fMpNMJidDygQHirbk7Byj2Y5IpVtvALAesyoh+VCGblzenREvdH3YE4D0onM5jWz
T1kRsv6vgiIodbYNAlgPdNXNNb134fMrYOJkWmeblHV0WIddZTcNlHjgAHK2quRJ
bAIER/A+IWKcN6sTgPfvHURcxpW8nhKsPUaSQQqqhdk1tLZquKGAg72eFW12A72f
VDMJ+337XD0=
=J1gB
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been doing
the work de-facto by himself recently is now the only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the newly
merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for later
rework (the current code is wrong in a harmless way), on Tegra
regression and one samsung spelling fix"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6: fix bogus use of irq_get_irq_data
ARM: imx: irq: fix buggy usage of irq_data irq field
MAINTAINERS: ARM Versatile Express platform, add missing pattern
MAINTAINERS: ARM Versatile Express platform
arm: ep93xx: add dma_masks for the M2P and M2M DMA controllers
MAINTAINERS: Add ahci_st.c to ARCH/STI architecture
MAINTAINERS: add entry for the GISB arbiter driver
MAINTAINERS: update brcmstb entries
MAINTAINERS: update email address and cleanup for exynos entry
ARM: tegra: Re-add removed SoC id macro to tegra_resume()
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: OMAP: serial: remove last vestige of DTR_gpio support.
ARM: OMAP2+: gpmc: Get rid of "ti,elm-id not found" warning
ARM: EXYNOS: fix typo in static struct name "exynos5_list_diable_wfi_wfe"
ARM: OMAP2: Remove unnecessary KERN_* in omap_phy_internal.c
ARM: OMAP4+: Remove unused omap_l3_noc platform init
ARM: dts: Add twl keypad map for omap3 EVM
ARM: dts: Add twl keypad map for LDP
ARM: dts: Fix NAND last partition size on LDP
ARM: OMAP3: Fix errors for omap_l3_smx when booted with device tree
The imx6 PM code seems to be quite creative in its use of irq_data,
using something that is very much a hardware interrupt number where
we expect a virtual one. Yes, it worked so far, but that's only
luck, and it will definitely explode in 3.19.
Fix it by using a pair of helper functions that deal with the
actual hardware.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
mach-imx directly references to the irq field in
struct irq_data, and uses this to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different.
Just replacing all instances of irq with hwirq fixes the issue.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The newly introduced LS1021A SoC selects CONFIG_SOC_FSL, which
is originally symbol used for the PowerPC based platforms
and guards lots of code that does not build on ARM.
This breaks allmodconfig, so let's remove it for now, until
either all those drivers are fixed or they use a dependency
on IMX instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With the clock assignment device tree changes, the clocks get
initialized properly but the search for those clocks fails with
errors:
[ 0.000000] i.MX clk 4: register failed with -17
[ 0.000000] i.MX clk 5: register failed with -17
This is because the module can't find those clocks anymore, and
tries to initialize fixed clocks with the same name.
Get the clock modules input clocks from the assigned clocks by
default by using of_clk_get_by_name(). If this function returns
not a valid clock, fall back to the old behaviour and search the
input clock from the device tree's /clocks/$name node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Freescale LS1021A SoCs deploy two cortex-A7 processors,
this adds bring-up support for the secondary core.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The LS1021A SoC is a dual-core Cortex-A7 based processor,
this adds the initial support for it.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instanciate device for the generic cpufreq-dt driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The ARM clock is a virtual clock feeding the ARM partition of
the SoC. It controls multiple other clocks to ensure the right
sequencing when cpufreq changes the CPU clock rate.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This implements a virtual clock used to abstract away
all the steps needed in order to change the ARM clock,
so we don't have to push all this clock handling into
the cpufreq driver.
While it will be used for i.MX53 at first it is generic
enough to be used on i.MX6 later on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is the bypass clock used to feed the ARM partition
while we reprogram PLL1 to another rate.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
