The size of the internal RAM of the DesignWare USB controller changed
between the different Lantiq SoCs. We have the following sizes:
Amazon + Danube: 8 KByte
Amazon SE + arx100: 2 KByte
xrx200 + xrx300: 2.5 KByte
For Danube SoC we do not provide the params and let the driver decide
to use sane defaults, for the Amazon SE and arx100 we use small fifos
and for the xrx200 and xrx300 SCs a little bit bigger periodic fifo.
The auto detection of max_transfer_size and max_packet_count should
work, so remove it.
This patch is included in OpenWrt for many years.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20240708222054.2727789-1-hauke@hauke-m.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using dma_map_sg() to map the scatterlist with iommu enabled,
the entries in the scatterlist can be mergerd into less but longer
entries in the function __finalise_sg(). So that the number of
valid mapped entries is actually smaller than ureq->num_reqs,and
there are still some invalid entries in the scatterlist with
dma_addr=0xffffffff and len=0. Writing these invalid sg entries
into the dma_desc can cause a data transmission error.
The function dma_map_sg() returns the number of valid map entries
and the return value is assigned to usb_request::num_mapped_sgs in
function usb_gadget_map_request_by_dev(). So that just write valid
mapped entries into dma_desc according to the usb_request::num_mapped_sgs,
and set the IOC bit if it's the last valid mapped entry.
This patch poses no risk to no-iommu situation, cause
ureq->num_mapped_sgs equals ureq->num_sgs while using dma_direct_map_sg()
to map the scatterlist whith iommu disabled.
Signed-off-by: Peng Hongchi <hongchi.peng@siengine.com>
Link: https://lore.kernel.org/r/20240523100315.7226-1-hongchi.peng@siengine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new bitfield GRSTCTL_CLOCK_SWITH_TIMER in GRSTCTL register.
This bitfield applicable HSOTG cores v5.00 or higher and not
applicable to HS/FS IOT devices.
This bitfield must be programmed to 3'b010 if core will be
used in Low-speed and core configured for any HS/FS PHY interface.
This bitfield must be programmed to 3'b111 if core configured
to use either:
- HS PHY interface UTMI or ULPI
- FS PHY any interface
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/0616838cfee958774c9321c6eeeda4be92f900d8.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added programmming of ULPI_LATCH_EN_DURING_HIB_ENTRY bit in GPWRDN
register when using ULPI PHY during entry/exit to/from hibernation.
This bit set to 1 during entering to hibernation if ULPI PHY used.
On exiting from hibernation this bit reset to 0.
Applicable for both host and device modes.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e024cb39a7177ec201c873df25ca6365f2e55947.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new bit ULPI_LATCH_EN_DURING_HIB_ENTRY in GPWRDN register.
This bit applicable HSOTG cores v5.00 or higher.
Affects Hibernation Entry and Exit sequence (for both Host and Device)
when using ULPI PHY.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/56d05a4f5750aaa58d8c5bab7705814942a985bd.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support eUSB2 PHY disconnect flow required in Soft disconnect
state set GOTGCTL_EUSB2_DISC_SUPP bit, if applicable.
On Session End Detected interrupt clear PCGCTL_GATEHCLK and
PCGCTL_STOPPCLK bits if eusb2_disc parameter true.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/9d50b83df693cda8c391313e90048df8dd611c04.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new parameter eusb2_disc to list of core parameters which specify
whether eUSB2 PHY disconnect support flow applicable or no.
Set to false as default value and checked core version if set to true.
This parameter applicable in device mode of HSOTG and HS IOT cores
v5.00 or higher.
Added print this parameter in show parameters of debugfs.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e77cc4312bda797d1ddaa4351d86c65a69c8b926.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC2 IP on the Rockchip SoCs doesn't support clock gating.
When a clock gating is enabled, system hangs.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/1703575199-23638-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_hc_n_intr() writes back INTMASK as read but evaluates it
with intmask applied. In stress testing this causes spurious
interrupts like this:
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 7 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 0 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_update_urb_state_abn(): trimming xfer length
Applying INTMASK prevents this. The issue exists in all versions of the
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Ivan Ivanov <ivan.ivanov@suse.com>
Tested-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20231115144514.15248-1-oneukum@suse.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231009211356.3242037-16-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In _dwc2_hcd_urb_enqueue(), "urb->hcpriv = NULL" is executed without
holding the lock "hsotg->lock". In _dwc2_hcd_urb_dequeue():
spin_lock_irqsave(&hsotg->lock, flags);
...
if (!urb->hcpriv) {
dev_dbg(hsotg->dev, "## urb->hcpriv is NULL ##\n");
goto out;
}
rc = dwc2_hcd_urb_dequeue(hsotg, urb->hcpriv); // Use urb->hcpriv
...
out:
spin_unlock_irqrestore(&hsotg->lock, flags);
When _dwc2_hcd_urb_enqueue() and _dwc2_hcd_urb_dequeue() are
concurrently executed, the NULL check of "urb->hcpriv" can be executed
before "urb->hcpriv = NULL". After urb->hcpriv is NULL, it can be used
in the function call to dwc2_hcd_urb_dequeue(), which can cause a NULL
pointer dereference.
This possible bug is found by an experimental static analysis tool
developed by myself. This tool analyzes the locking APIs to extract
function pairs that can be concurrently executed, and then analyzes the
instructions in the paired functions to identify possible concurrency
bugs including data races and atomicity violations. The above possible
bug is reported, when my tool analyzes the source code of Linux 6.5.
To fix this possible bug, "urb->hcpriv = NULL" should be executed with
holding the lock "hsotg->lock". After using this patch, my tool never
reports the possible bug, with the kernelconfiguration allyesconfig for
x86_64. Because I have no associated hardware, I cannot test the patch
in runtime testing, and just verify it according to the code logic.
Fixes: 33ad261aa6 ("usb: dwc2: host: spinlock urb_enqueue")
Signed-off-by: Jia-Ju Bai <baijiaju@buaa.edu.cn>
Link: https://lore.kernel.org/r/20230926024404.832096-1-baijiaju@buaa.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2 driver has everything we need to run in PCI mode except
for pci_device_id driver_data parse. With that to set Loongson
dwc2 element and added identified as PCI_VENDOR_ID_LOONGSON
and PCI_DEVICE_ID_LOONGSON_DWC2 in dwc2_pci_ids, the Loongson
dwc2 controller will work.
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20230815065833.3375-1-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller is dead, the honest answer to the
question whether it has caused an irq is: unknown
As the purpose of the irq return is to trigger switching
off an IRQ, the correct response if you cannot
determine if your device has caused the interrupt is
IRQ_HANDLED
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20230822112455.18957-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530071913.2192214-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Amlogic A1 uses dwc2 Synopsys IP as its USB peripheral (gadget)
endpoint, with different DWC2 parameters when compared to previous
Amlogic SoCs.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20230511210455.6634-2-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_driver_probe() calls dwc2_lowlevel_hw_init() which deassert some reset
lines.
Should an error happen in dwc2_lowlevel_hw_init() after calling
reset_control_deassert() or in the probe after calling
dwc2_lowlevel_hw_init(), the reset lines remain deasserted.
Add some devm_add_action_or_reset() calls to re-assert the lines if needed.
Update the remove function accordingly.
This change is compile-tested only.
Fixes: 83f8da562f ("usb: dwc2: Add reset control to dwc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c64537b5339342bd00f7c2152b8fc23792b9f95a.1683306479.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the utmi clock. It's needed on STM32MP15, when using
the integrated full-speed PHY. This clock is an output of USBPHYC, but
HS USBPHYC is not attached as PHY in this case: Full-Speed PHY is directly
managed in dwc2 glue, through GGPIO register. Typical DT when using FS PHY
&usbotg_hs {
compatible = "st,stm32mp15-fsotg", "snps,dwc2";
pinctrl-names = "default";
pinctrl-0 = <&usbotg_hs_pins_a &usbotg_fs_dp_dm_pins_a>;
vbus-supply = <&vbus_otg>;
status = "okay";
};
In this configuration, USBPHYC clock output must be defined, so it can
be properly enabled as a clock provider:
clocks = <&rcc USBO_K>, <&usbphyc>;
clock-names = "otg", "utmi";
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-4-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error handling in __dwc2_lowlevel_hw_enable() that may leave the
clocks and regulators enabled upon error.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-2-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes here, and the USB gadget update for future
development patches to be based on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in dual role mode (dr_mode == USB_DR_MODE_OTG), platform probe
successively basically calls:
- dwc2_gadget_init()
- dwc2_hcd_init()
- dwc2_lowlevel_hw_disable() since recent change [1]
- usb_add_gadget_udc()
The PHYs (and so the clocks it may provide) shouldn't be disabled for all
SoCs, in OTG mode, as the HCD part has been initialized.
On STM32 this creates some weird race condition upon boot, when:
- initially attached as a device, to a HOST
- and there is a gadget script invoked to setup the device part.
Below issue becomes systematic, as long as the gadget script isn't
started by userland: the hardware PHYs (and so the clocks provided by the
PHYs) remains disabled.
It ends up in having an endless interrupt storm, before the watchdog
resets the platform.
[ 16.924163] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
[ 16.962704] dwc2 49000000.usb-otg: DWC OTG Controller
[ 16.966488] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 2
[ 16.974051] dwc2 49000000.usb-otg: irq 77, io mem 0x49000000
[ 17.032170] hub 2-0:1.0: USB hub found
[ 17.042299] hub 2-0:1.0: 1 port detected
[ 17.175408] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.181741] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.189303] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
...
The host part is also not functional, until the gadget part is configured.
The HW may only be disabled for peripheral mode (original init), e.g.
dr_mode == USB_DR_MODE_PERIPHERAL, until the gadget driver initializes.
But when in USB_DR_MODE_OTG, the HW should remain enabled, as the HCD part
is able to run, while the gadget part isn't necessarily configured.
I don't fully get the of purpose the original change, that claims disabling
the hardware is missing. It creates conditions on SOCs using the PHY
initialization to be completely non working in OTG mode. Original
change [1] should be reworked to be platform specific.
[1] https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com
Fixes: ade23d7b7e ("usb: dwc2: power on/off phy for peripheral mode in dual-role mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20230315144433.3095859-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the platform goes to low power, PM suspend / resume routines
call: __dwc2_lowlevel_hw_enable -> devm_add_action_or_reset().
This adds a new devres each time.
This may also happen at runtime, as dwc2_lowlevel_hw_enable() can be
called from udc_start().
This can be seen with tracing:
- echo 1 > /sys/kernel/debug/tracing/events/dev/devres_log/enable
- go to low power
- cat /sys/kernel/debug/tracing/trace
A new "ADD" entry is found upon each low power cycle:
... devres_log: 49000000.usb-otg ADD 82a13bba devm_action_release (8 bytes)
... devres_log: 49000000.usb-otg ADD 49889daf devm_action_release (8 bytes)
...
A second issue is addressed here:
- regulator_bulk_enable() is called upon each PM cycle (suspend/resume).
- regulator_bulk_disable() never gets called.
So the reference count for these regulators constantly increase, by one
upon each low power cycle, due to missing regulator_bulk_disable() call
in __dwc2_lowlevel_hw_disable().
The original fix that introduced the devm_add_action_or_reset() call,
fixed an issue during probe, that happens due to other errors in
dwc2_driver_probe() -> dwc2_core_reset(). Then the probe fails without
disabling regulators, when dr_mode == USB_DR_MODE_PERIPHERAL.
Rather fix the error path: disable all the low level hardware in the
error path, by using the "hsotg->ll_hw_enabled" flag. Checking dr_mode
has been introduced to avoid a dual call to dwc2_lowlevel_hw_disable().
"ll_hw_enabled" should achieve the same (and is used currently in the
remove() routine).
Fixes: 54c1960605 ("usb: dwc2: Always disable regulators on driver teardown")
Fixes: 33a06f1300 ("usb: dwc2: Fix error path in gadget registration")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230316084127.126084-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20230310144729.1545857-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some boards might use USB-A female connector for USB ports, however,
the port could be connected to a dual-mode USB controller, making it
also behaves as a peripheral device if male-to-male cable is connected.
In this case, the dts looks like this:
&usb0 {
status = "okay";
dr_mode = "otg";
usb-role-switch;
role-switch-default-mode = "host";
};
After boot, dwc2_ovr_init() sets GOTGCTL to GOTGCTL_AVALOVAL and call
dwc2_force_mode() with parameter host=false, which causes inconsistent
mode - The hardware is in peripheral mode while the kernel status is
in host mode.
What we can do now is to call dwc2_drd_role_sw_set() to switch to
device mode, and everything should work just fine now, even switching
back to none(default) mode afterwards.
Fixes: e14acb8769 ("usb: dwc2: drd: add role-switch-default-node support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/SG2PR01MB204837BF68EDB0E343D2A375C9A59@SG2PR01MB2048.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY power is handled for peripheral mode but only when the device is
forced into this peripheral mode. It is missing when the device is
operating in peripheral mode when dual-role mode is enabled, so let's
update the condition to match this scenario.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPM feature of DWC2 module integrated in Rockchip SoCs doesn't work
properly or needs some additional handling, so disable it for now.
Without disabling LPM feature, the USB ADB communication fail with
the following error log:
dwc2 ff580000.usb: new address 27
dwc2 ff580000.usb: Failed to exit L1 sleep state in 200us.
dwc2 ff580000.usb: dwc2_hsotg_send_reply: cannot queue req
dwc2 ff580000.usb: dwc2_hsotg_process_req_status: failed to send reply
dwc2 ff580000.usb: dwc2_hsotg_enqueue_setup: failed queue (-11)
dwc2 ff580000.usb: Failed to exit L1 sleep state in 200us.
[diff vs vendor kernel: added lpm_clock_gating, besl and
hird_threshold_en settings as seen in commit 53febc9569 ("usb: dwc2:
disable Link Power Management on STM32MP15 HS OTG")]
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-1-36515e1092cd@theobroma-systems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning an error value in a platform driver's remove callback results in
a generic error message being emitted by the driver core, but otherwise it
doesn't make a difference. The device goes away anyhow.
For each case where ret is non-zero the driver already emits an error
message, so suppress the generic error message by returning zero
unconditionally. (Side note: The return value handling was unreliable
anyhow as the value returned by dwc2_exit_hibernation() was overwritten
anyhow if hsotg->in_ppd was non-zero.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20221017195914.1426297-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPDX-License-Identifier have been added in commit 5fd54ace47 ("USB: add
SPDX identifiers to all remaining files in drivers/usb/")
There is no point in keeping the now redundant license text.
Remove it.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/030a7e187d707f8734a492cda7a6b54d459c4bb3.1662788747.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 1599069a62 ("phy: core: Warn when phy_power_on is called before
phy_init") the driver complains. In my case (Amlogic SoC) the warning
is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init
So change the order of the two calls. The same change has to be done
to the order of phy_exit() and phy_power_off().
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Cc: stable@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/dfcc6b40-2274-4e86-e73c-5c5e6aa3e046@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
there is an unexpected word "the" in the comments that need to be dropped
file: ./drivers/usb/dwc2/hcd.c
line: 1002
* even and the current frame number is even the the transfer
changed to:
* even and the current frame number is even the transfer
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622103558.6647-1-jiangjian@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using usb-role-switch, D+ pull-up is set as soon as DTCL_SFTDISCON is
cleared, whatever the vbus valid signal state is. The pull-up should not
be set when vbus isn't present (this is determined by the drd controller).
This patch ensures that B-Session (so Peripheral role + vbus valid signal)
is valid before clearing the DCTL_SFTDISCON bit when role switch is used.
Keep original behavior when usb-role-switch isn't used.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220622160717.314580-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Target Peripheral List (TPL) is used to identify targeted devices
during Embedded Host compliance testing. The user can add "tpl-support"
in the device tree to enable it.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20220621152350.145745-5-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_create_hcd will alloc memory for hcd, and we should
call usb_put_hcd to free it when platform_get_resource()
fails to prevent memory leak.
goto error2 label instead error1 to fix this.
Fixes: 856e6e8e0f ("usb: dwc2: check return value after calling platform_get_resource()")
Cc: stable <stable@kernel.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220530085413.44068-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UDC driver should not touch gadget's driver internals, especially it
should not reset driver->bus. This wasn't harmful so far, but since
commit fc274c1e99 ("USB: gadget: Add a new bus for gadgets") gadget
subsystem got it's own bus and messing with ->bus triggers the
following NULL pointer dereference:
dwc2 12480000.hsotg: bound driver g_ether
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: ...
CPU: 0 PID: 620 Comm: modprobe Not tainted 5.18.0-rc5-next-20220504 #11862
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at module_add_driver+0x44/0xe8
LR is at sysfs_do_create_link_sd+0x84/0xe0
...
Process modprobe (pid: 620, stack limit = 0x(ptrval))
...
module_add_driver from bus_add_driver+0xf4/0x1e4
bus_add_driver from driver_register+0x78/0x10c
driver_register from usb_gadget_register_driver_owner+0x40/0xb4
usb_gadget_register_driver_owner from do_one_initcall+0x44/0x1e0
do_one_initcall from do_init_module+0x44/0x1c8
do_init_module from load_module+0x19b8/0x1b9c
load_module from sys_finit_module+0xdc/0xfc
sys_finit_module from ret_fast_syscall+0x0/0x54
Exception stack(0xf1771fa8 to 0xf1771ff0)
...
dwc2 12480000.hsotg: new device is high-speed
---[ end trace 0000000000000000 ]---
Fix this by removing driver->bus entry reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220505104618.22729-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add OTG support for the JZ4775 SoC, the JZ4780 SoC, the X1000 SoC,
the X1600 SoC, the X1700 SoC, the X1830 SoC, and the X2000 SoC
from Ingenic.
Introduce support for disable Ingenic overcurrent detection, once
selected, it enables the GOTGCTL register bits VbvalidOvEn and
VbvalidOvVal to disable the VBUS overcurrent detection.
This patch is derived from Dragan Čečavac (in the kernel 3.18.3
tree of CI20). It is very useful for the MIPS Creator CI20 (r1).
Without this patch, OTG port of CI20 has a great probability to
face overcurrent warning, which breaks the OTG functionality.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Dragan Čečavac <dragancecavac@yahoo.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/1649964337-114337-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
