On SAM9X60, slewrate should be enabled on pins with a switching frequency
below 50Mhz. Since most of our pins do not exceed this value, we enable
slewrate by default. Pins with a switching value that exceeds 50Mhz will
have to explicitly disable slewrate.
This patch changes the ABI. However, the slewrate macros are only used
by SAM9X60 and, at this moment, there are no device-tree files available
for this platform.
Suggested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20191101092031.24896-1-codrin.ciubotariu@microchip.com
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for the new R-Car M3-W+ (r8a77961) SoC,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXbxIwAAKCRCKwlD9ZEnx
cD0JAP9Zk4yPHStUiiwPKwx+ZCJJ2wAAyKLXhSBKLh06h2CKOQEApFYk4xfPAe+f
wsM8M04QtlsYp1ZgX2wpbXiZeBdM+gg=
=OJxF
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.5-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.5 (take two)
- Add support for the new R-Car M3-W+ (r8a77961) SoC,
- Small fixes and cleanups.
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
Add support for the Pin Function Controller in the R-Car M3-W+
(R8A77961) SoC.
R-Car M3-W+ is pin compatible with R-Car M3-W (R8A77960), which allows
for both SoCs to share a driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-4-geert+renesas@glider.be
Rename CONFIG_PINCTRL_PFC_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_PINCTRL_PFC_R8A77960, to avoid confusion with R-Car M3-W+
(R8A77961), which will use CONFIG_PINCTRL_PFC_R8A77961.
Extend the dependency of CONFIG_PINCTRL_PFC_R8A77960 from
CONFIG_ARCH_R8A7796 to CONFIG_ARCH_R8A77960, to relax dependencies for a
future rename of the SoC configuration symbol.
Rename r8a7796_pinmux_info to r8a77960_pinmux_info, as it contains an
r8a77960-based name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-3-geert+renesas@glider.be
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
sh-pfc e6060000.pin-controller: IRQ index 0 not found
Fix this by using the platform_irq_count() helper instead.
Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191016142601.28255-1-geert+renesas@glider.be
This driver adds pinctrl/GPIO support for Intel Tiger Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can restore only values that had been changed and do not spam kernel log
with unnecessary messages. Convert intel_gpio_update_pad_mode() to a helper
function that will be used across few callers.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we didn't get any new reports from users about wrong settings
of pad ownership, there is no point to spam kernel log with it. Thus,
drop level from warning to debug.
Also, modify format to be in align with the rest restore helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Refactor restoring GPI_IE registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Refactor restoring HOSTSW_OWN registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Deduplicate restoring PADCFGx registers by using a common helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bbebeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc11312f ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
One spelling mistake is being fixed: benerate -> generate.
It is a complimentary fix to the commit 505485a83c55 ("pinctrl:
cherryview fixed typo in comment").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
A couple more fixes for Intel pinctrl drivers:
- Try to avoid glitches when pin is in GPIO mode
- Fix cherryview irq_valid_mask calculation
- Allocate cherryview IRQ chip dynamically to avoid triggering warning
from GPIO core
-----BEGIN PGP SIGNATURE-----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=3AVf
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl fixes for v5.4 part 2
A couple more fixes for Intel pinctrl drivers:
- Try to avoid glitches when pin is in GPIO mode
- Fix cherryview irq_valid_mask calculation
- Allocate cherryview IRQ chip dynamically to avoid triggering warning
from GPIO core
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bbebeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc11312f ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
- Add support for the new RZ/G2N (r8a774b1) SoC,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXal5/gAKCRCKwlD9ZEnx
cLbfAQCW3HRFA6EGzMOSweSZ+IE1SpaC+K6i8Is9hN+zyXDaYQEA6vskgARnL+SI
NCg42XOKhNNkLYoy7D2dKnkruYbsKA4=
=c90h
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.5
- Add support for the new RZ/G2N (r8a774b1) SoC,
- Small fixes and cleanups.
Commit 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the new Spreadtrum pin controller, it expands 6bits to describe the
pin sleep mode with adding one CM4_SLEEP mode, which means the pin sleep
related configuration will be loaded automatically by hardware when the
CM4 system goes into deep sleep mode.
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/8ae52263b0625c416461821c457e6789b67170b6.1571228451.git.baolin.wang@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AST2600 EMMC support 3 types DAT bus sizes (1, 4 and 8-bit),
corresponding to 3 groups: EMMCG1, EMMCG4 and EMMCG8
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-8-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When UART13G1 is set the pinmux configuration in SCU4B8 for UART13G0
should be cleared.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-7-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signal descriptors can represent multi-bit bitfields and so have
explicit "enable" and "disable" states. However many descriptor
instances only describe a single bit, and so the SIG_DESC_SET() macro is
provides an abstraction for the single-bit cases: Its expansion
configures the "enable" state to set the bit and "disable" to clear.
SIG_DESC_CLEAR() was introduced to provide a similar single-bit
abstraction for for descriptors to clear the bit of interest. However
its behaviour was defined as the literal inverse of SIG_DESC_SET() - the
impact is the bit of interest is set in the disable path. This behaviour
isn't intuitive and doesn't align with how we want to use the macro in
practice, so make it clear the bit for both the enable and disable
paths.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-6-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The documentation to configure I3C3/FSI1 and I3C4/FSI2 was initially
unclear.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message, resolve rebase conflicts]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-5-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C function the pin participated in was incorrectly named SDA14
which lead to a failure to mux:
[ 6.884344] No function I2C14 found on pin 7 (7). Found signal(s) MACLINK4, SDA14, GPIOA7 for function(s) MACLINK4, SDA14, GPIOA7
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-4-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins crept in that weren't ordered in the list.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-3-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-2-linus.walleij@linaro.org
The latent IRQs are IRQs that have occurred when the system
was down in deep sleep and the GPIO block was powered off.
The PRCMU (power reset and control unit) knows which GPIO
line offset fired an IRQ to wake the system up (if so
desired) and this second IRQ was used to replay the action
when the system came back online after suspend().
This is now known to be the wrong approach to solve this
problem: in a patch series Lina Iyer has suggested to
instead make it possible to model the IRQs as hierarchical
with double parents.
Also the current device trees do not contain the right
information to make this code work, the latent IRQ is not
specified nowadays giving noise like this in the console:
[ 0.612168] gpio 8012e000.gpio: IRQ index 1 not found
[ 0.622523] gpio 8012e080.gpio: IRQ index 1 not found
Let's delete the latent IRQ code and reimplement it properly
when we need it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-1-linus.walleij@linaro.org
When an STMFX IO is used as interrupt through the interrupt-controller
binding, the STMFX driver should configure this IO as input. Default
value of STMFX IO direction is input, but if the IO is used as output
before the interrupt use, it will not work without these callbacks.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191009091606.17283-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver to support pin configuration with the
pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191005105936.31216-2-kholk11@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Zhou Yanjie <zhouyanjie@zoho.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191001133209.17164-1-linus.walleij@linaro.org
Add support for the PM6150 and PM6150L GPIO support to the
Qualcomm PMIC GPIO binding.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Link: https://lore.kernel.org/r/1570188039-22122-1-git-send-email-kgunda@codeaurora.org
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: James Hartley <james.hartley@sondrel.com>
Link: https://lore.kernel.org/r/20191001214536.18477-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191002121550.16104-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20191002114454.9684-1-linus.walleij@linaro.org
The function should be spdifib, fix this typo.
Fixes: 423ddc580b13 ("pinctrl: berlin: add the as370 SoC pinctrl driver")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20191011154321.44f08f9a@xhacker.debian
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191002113819.4927-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion: the ST pin controller errors out of adding a
irqchip if the interrupt is invalid or missing or if the
irqmux is not present: the irqchip should not be added
if either of these errors happen, so rewrite the code to
deal with that. Keep the exit path where the gpio_chip
is added no matter what the status of the irq is.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191001135147.29416-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion: at91 is a little bit special since it registers
up to 3 gpio_chips with the same parent handler, but just
passing girq->parent_handler and the parent on the first
of them should cut it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20191001130645.8350-1-linus.walleij@linaro.org
