Add cputype definitions for Neoverse-N3. These will be used for errata
detection in subsequent patches.
These values can be found in Table A-261 ("MIDR_EL1 bit descriptions")
in issue 02 of the Neoverse-N3 TRM, which can be found at:
https://developer.arm.com/documentation/107997/0000/?lang=en
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20240930111705.3352047-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Certain portions of code always need to be position-independent
regardless of CONFIG_RELOCATABLE, including code which is executed in an
idmap or which is executed before relocations are applied. In some
kernel configurations the LLD linker generates position-dependent
veneers for such code, and when executed these result in early boot-time
failures.
Marc Zyngier encountered a boot failure resulting from this when
building a (particularly cursed) configuration with LLVM, as he reported
to the list:
https://lore.kernel.org/linux-arm-kernel/86wmjwvatn.wl-maz@kernel.org/
In Marc's kernel configuration, the .head.text and .rodata.text sections
end up more than 128MiB apart, requiring a veneer to branch between the
two:
| [mark@lakrids:~/src/linux]% usekorg 14.1.0 aarch64-linux-objdump -t vmlinux | grep -w _text
| ffff800080000000 g .head.text 0000000000000000 _text
| [mark@lakrids:~/src/linux]% usekorg 14.1.0 aarch64-linux-objdump -t vmlinux | grep -w primary_entry
| ffff8000889df0e0 g .rodata.text 000000000000006c primary_entry,
... consequently, LLD inserts a position-dependent veneer for the branch
from _stext (in .head.text) to primary_entry (in .rodata.text):
| ffff800080000000 <_text>:
| ffff800080000000: fa405a4d ccmp x18, #0x0, #0xd, pl // pl = nfrst
| ffff800080000004: 14003fff b ffff800080010000 <__AArch64AbsLongThunk_primary_entry>
...
| ffff800080010000 <__AArch64AbsLongThunk_primary_entry>:
| ffff800080010000: 58000050 ldr x16, ffff800080010008 <__AArch64AbsLongThunk_primary_entry+0x8>
| ffff800080010004: d61f0200 br x16
| ffff800080010008: 889df0e0 .word 0x889df0e0
| ffff80008001000c: ffff8000 .word 0xffff8000
... and as this is executed early in boot before the kernel is mapped in
TTBR1 this results in a silent boot failure.
Fix this by passing '--pic-veneer' to the linker, which will cause the
linker to use position-independent veneers, e.g.
| ffff800080000000 <_text>:
| ffff800080000000: fa405a4d ccmp x18, #0x0, #0xd, pl // pl = nfrst
| ffff800080000004: 14003fff b ffff800080010000 <__AArch64ADRPThunk_primary_entry>
...
| ffff800080010000 <__AArch64ADRPThunk_primary_entry>:
| ffff800080010000: f004e3f0 adrp x16, ffff800089c8f000 <__idmap_text_start>
| ffff800080010004: 91038210 add x16, x16, #0xe0
| ffff800080010008: d61f0200 br x16
I've opted to pass '--pic-veneer' unconditionally, as:
* In addition to solving the boot failure, these sequences are generally
nicer as they require fewer instructions and don't need to perform
data accesses.
* While the position-independent veneer sequences have a limited +/-2GiB
range, this is not a new restriction. Even kernels built with
CONFIG_RELOCATABLE=n are limited to 2GiB in size as we have several
structues using 32-bit relative offsets and PPREL32 relocations, which
are similarly limited to +/-2GiB in range. These include extable
entries, jump table entries, and alt_instr entries.
* GNU LD defaults to using position-independent veneers, and supports
the same '--pic-veneer' option, so this change is not expected to
adversely affect GNU LD.
I've tested with GNU LD 2.30 to 2.42 inclusive and LLVM 13.0.1 to 19.1.0
inclusive, using the kernel.org binaries from:
* https://mirrors.edge.kernel.org/pub/tools/crosstool/
* https://mirrors.edge.kernel.org/pub/tools/llvm/
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Marc Zyngier <maz@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240927101838.3061054-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is no links_num in struct snd_soc_acpi_mach {}, and we test
!link->num_adr as a condition to end the loop in hda_sdw_machine_select().
So an empty item in struct snd_soc_acpi_link_adr array is required.
Fixes: 65ab45b906 ("ASoC: Intel: soc-acpi: Add match entries for some cs42l43 laptops")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241001061738.34854-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Regression Description:
Depending on the options specified for the GRE tunnel device, small
packets may be dropped. This occurs because the pskb_network_may_pull
function fails due to the packet's insufficient length.
For example, if only the okey option is specified for the tunnel device,
original (before encapsulation) packets smaller than 28 bytes (including
the IPv4 header) will be dropped. This happens because the required
length is calculated relative to the network header, not the skb->head.
Here is how the required length is computed and checked:
* The pull_len variable is set to 28 bytes, consisting of:
* IPv4 header: 20 bytes
* GRE header with Key field: 8 bytes
* The pskb_network_may_pull function adds the network offset, shifting
the checkable space further to the beginning of the network header and
extending it to the beginning of the packet. As a result, the end of
the checkable space occurs beyond the actual end of the packet.
Instead of ensuring that 28 bytes are present in skb->head, the function
is requesting these 28 bytes starting from the network header. For small
packets, this requested length exceeds the actual packet size, causing
the check to fail and the packets to be dropped.
This issue affects both locally originated and forwarded packets in
DMVPN-like setups.
How to reproduce (for local originated packets):
ip link add dev gre1 type gre ikey 1.9.8.4 okey 1.9.8.4 \
local <your-ip> remote 0.0.0.0
ip link set mtu 1400 dev gre1
ip link set up dev gre1
ip address add 192.168.13.1/24 dev gre1
ip neighbor add 192.168.13.2 lladdr <remote-ip> dev gre1
ping -s 1374 -c 10 192.168.13.2
tcpdump -vni gre1
tcpdump -vni <your-ext-iface> 'ip proto 47'
ip -s -s -d link show dev gre1
Solution:
Use the pskb_may_pull function instead the pskb_network_may_pull.
Fixes: 80d875cfc9 ("ipv4: ip_gre: Avoid skb_pull() failure in ipgre_xmit()")
Signed-off-by: Anton Danilov <littlesmilingcloud@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240924235158.106062-1-littlesmilingcloud@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This reverts commit 740ff03d72 because
current PixArt detection is too greedy and claims devices that are
not PixArt.
Reported-by: Benjamin Tissoires <bentiss@kernel.org>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2314756
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Increase the timeout for checking the busy bit of the VLAN Tag register
from 10µs to 500ms. This change is necessary to accommodate scenarios
where Energy Efficient Ethernet (EEE) is enabled.
Overnight testing revealed that when EEE is active, the busy bit can
remain set for up to approximately 300ms. The new 500ms timeout provides
a safety margin.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://patch.msgid.link/20240924205424.573913-1-shenwei.wang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
iter_folioq_get_pages() decides to advance to the next folioq slot when
it has reached the end of the current folio. However, it is checking
offset, which is the beginning of the current part, instead of
iov_offset, which is adjusted to the end of the current part, so it
doesn't advance the slot when it's supposed to. As a result, on the next
iteration, we'll use the same folio with an out-of-bounds offset and
return an unrelated page.
This manifested as various crashes and other failures in 9pfs in drgn's
VM testing setup and BPF CI.
Fixes: db0aa2e956 ("mm: Define struct folio_queue and ITER_FOLIOQ to handle a sequence of folios")
Link: https://lore.kernel.org/linux-fsdevel/20240923183432.1876750-1-chantr4@gmail.com/
Tested-by: Manu Bretelle <chantr4@gmail.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Link: https://lore.kernel.org/r/cbaf141ba6c0e2e209717d02746584072844841a.1727722269.git.osandov@fb.com
Tested-by: Eduard Zingerman <eddyz87@gmail.com>
Tested-by: Leon Romanovsky <leon@kernel.org>
Tested-by: Joey Gouly <joey.gouly@arm.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
RISC-V perf driver does not yet support PERF_TYPE_BREAKPOINT. It would
be more appropriate to return -EOPNOTSUPP or -ENOENT for this type in
pmu_sbi_event_map. Considering that other implementations return -ENOENT
for unsupported perf types, let's synchronize this behavior. Due to this
reason, a riscv bpf testcases perf_skip fail. Meanwhile, align that
behavior to the rest of proper place.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Fixes: 9b3e150e31 ("RISC-V: Add a simple platform driver for RISC-V legacy perf")
Fixes: 16d3b1af09 ("perf: RISC-V: Check standard event availability")
Fixes: e999143459 ("RISC-V: Add perf platform driver based on SBI PMU extension")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240831071520.1630360-1-pulehui@huaweicloud.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Eric Dumazet says:
====================
net: two fixes for qdisc_pkt_len_init()
Inspired by one syzbot report.
At least one qdisc (fq_codel) depends on qdisc_skb_cb(skb)->pkt_len
having a sane value (not zero)
With the help of af_packet, syzbot was able to fool qdisc_pkt_len_init()
to precisely set qdisc_skb_cb(skb)->pkt_len to zero.
First patch fixes this issue.
Second one (a separate one to help future bisections) adds
more sanity check to SKB_GSO_DODGY users.
====================
Link: https://patch.msgid.link/20240924150257.1059524-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
One path takes care of SKB_GSO_DODGY, assuming
skb->len is bigger than hdr_len.
virtio_net_hdr_to_skb() does not fully dissect TCP headers,
it only make sure it is at least 20 bytes.
It is possible for an user to provide a malicious 'GSO' packet,
total length of 80 bytes.
- 20 bytes of IPv4 header
- 60 bytes TCP header
- a small gso_size like 8
virtio_net_hdr_to_skb() would declare this packet as a normal
GSO packet, because it would see 40 bytes of payload,
bigger than gso_size.
We need to make detect this case to not underflow
qdisc_skb_cb(skb)->pkt_len.
Fixes: 1def9238d4 ("net_sched: more precise pkt_len computation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The number of register fields cannot be assumed to be ALE_FIELDS_MAX
as some platforms can have lesser fields.
Solve this by embedding the actual number of fields available
in platform data and use that instead of ALE_FIELDS_MAX.
Gets rid of the below warning on BeagleBone Black
[ 1.007735] WARNING: CPU: 0 PID: 33 at drivers/base/regmap/regmap.c:1208 regmap_field_init+0x88/0x9c
[ 1.007802] invalid empty mask defined
[ 1.007812] Modules linked in:
[ 1.007842] CPU: 0 UID: 0 PID: 33 Comm: kworker/u4:3 Not tainted 6.11.0-01459-g508403ab7b74-dirty #840
[ 1.007867] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 1.007890] Workqueue: events_unbound deferred_probe_work_func
[ 1.007935] Call trace:
[ 1.007957] unwind_backtrace from show_stack+0x10/0x14
[ 1.007999] show_stack from dump_stack_lvl+0x50/0x64
[ 1.008033] dump_stack_lvl from __warn+0x70/0x124
[ 1.008077] __warn from warn_slowpath_fmt+0x194/0x1a8
[ 1.008113] warn_slowpath_fmt from regmap_field_init+0x88/0x9c
[ 1.008154] regmap_field_init from devm_regmap_field_alloc+0x48/0x64
[ 1.008193] devm_regmap_field_alloc from cpsw_ale_create+0xfc/0x320
[ 1.008251] cpsw_ale_create from cpsw_init_common+0x214/0x354
[ 1.008286] cpsw_init_common from cpsw_probe+0x4ac/0xb88
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/netdev/CAMuHMdUf-tKRDzkz2_m8qdFTFutefddU0NTratVrEjRTzA3yQQ@mail.gmail.com/
Fixes: 11cbcfeaa7 ("net: ethernet: ti: cpsw_ale: use regfields for number of Entries and Policers")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240924-am65-cpsw-multi-rx-fix-v1-1-0ca3fa9a1398@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is no need to ask the user about enabling Microchip FDMA
functionality, as all drivers that use it select the FDMA symbol.
Hence make the symbol invisible, unless when compile-testing.
Fixes: 30e48a75df ("net: microchip: add FDMA library")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://patch.msgid.link/8e2bcd8899c417a962b7ee3f75b29f35b25d7933.1727171879.git.geert+renesas@glider.be
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On link-state change, the controller gets reset,
which clears all PTP registers, including PHC time,
calibrated clock correction values etc. For correct
IEEE 1588 operation we need to restore these after
the reset.
Fixes: 6605b730c0 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20240924093705.2897329-2-csokas.bence@prolan.hu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On link state change, the controller gets reset,
causing PPS to drop out. Re-enable PPS if it was
enabled before the controller reset.
Fixes: 6605b730c0 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20240924093705.2897329-1-csokas.bence@prolan.hu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The value is read from the register TXGBE_RX_GEN_CTL3, and it should be
written back to TXGBE_RX_GEN_CTL3 when it changes some fields.
Cc: stable@vger.kernel.org
Fixes: f629acc6f2 ("net: pcs: xpcs: support to switch mode for Wangxun NICs")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20240924022857.865422-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When applying padding, the buffer is not zeroed, which results in memory
disclosure. The mentioned data is observed on the wire. This patch uses
skb_put_padto() to pad Ethernet frames properly. The mentioned function
zeroes the expanded buffer.
In case the packet cannot be padded it is silently dropped. Statistics
are also not incremented. This driver does not support statistics in the
old 32-bit format or the new 64-bit format. These will be added in the
future. In its current form, the patch should be easily backported to
stable versions.
Ethernet MACs on Amazon-SE and Danube cannot do padding of the packets
in hardware, so software padding must be applied.
Fixes: 504d4721ee ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240923214949.231511-2-olek2@wp.pl
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 24ab059d2e ("net: check dev->gso_max_size in gso_features_check()")
added a dev->gso_max_size test to gso_features_check() in order to fall
back to GSO when needed.
This was added as it was noticed that some drivers could misbehave if TSO
packets get too big. However, the check doesn't respect dev->gso_ipv4_max_size
limit. For instance, a device could be configured with BIG TCP for IPv4,
but not IPv6.
Therefore, add a netif_get_gso_max_size() equivalent to netif_get_gro_max_size()
and use the helper to respect both limits before falling back to GSO engine.
Fixes: 24ab059d2e ("net: check dev->gso_max_size in gso_features_check()")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240923212242.15669-2-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a small netif_get_gro_max_size() helper which returns the maximum IPv4
or IPv6 GRO size of the netdevice.
We later add a netif_get_gso_max_size() equivalent as well for GSO, so that
these helpers can be used consistently instead of open-coded checks.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240923212242.15669-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The constructor of ConfigMainWindow() calls show*View(), which needs
to calculate symbol values. conf_read() must be called before that.
Fixes: 060e05c3b4 ("kconfig: qconf: remove initial call to conf_changed()")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Since commit 95573cac25 ("kconfig: cache expression values"), xconfig
emits a lot of false-positive "unmet direct dependencies" warnings.
While conf_read() clears val_is_valid flags, 'make xconfig' calculates
symbol values even before the conf_read() call. This is another issue
that should be addressed separately, but it has revealed that the
val_is_valid field is not initialized.
Fixes: 95573cac25 ("kconfig: cache expression values")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Alexander Sverdlin presents 2 problems during shutdown with the
lan9303 driver. One is specific to lan9303 and the other just happens
to reproduce there.
The first problem is that lan9303 is unique among DSA drivers in that it
calls dev_get_drvdata() at "arbitrary runtime" (not probe, not shutdown,
not remove):
phy_state_machine()
-> ...
-> dsa_user_phy_read()
-> ds->ops->phy_read()
-> lan9303_phy_read()
-> chip->ops->phy_read()
-> lan9303_mdio_phy_read()
-> dev_get_drvdata()
But we never stop the phy_state_machine(), so it may continue to run
after dsa_switch_shutdown(). Our common pattern in all DSA drivers is
to set drvdata to NULL to suppress the remove() method that may come
afterwards. But in this case it will result in an NPD.
The second problem is that the way in which we set
dp->conduit->dsa_ptr = NULL; is concurrent with receive packet
processing. dsa_switch_rcv() checks once whether dev->dsa_ptr is NULL,
but afterwards, rather than continuing to use that non-NULL value,
dev->dsa_ptr is dereferenced again and again without NULL checks:
dsa_conduit_find_user() and many other places. In between dereferences,
there is no locking to ensure that what was valid once continues to be
valid.
Both problems have the common aspect that closing the conduit interface
solves them.
In the first case, dev_close(conduit) triggers the NETDEV_GOING_DOWN
event in dsa_user_netdevice_event() which closes user ports as well.
dsa_port_disable_rt() calls phylink_stop(), which synchronously stops
the phylink state machine, and ds->ops->phy_read() will thus no longer
call into the driver after this point.
In the second case, dev_close(conduit) should do this, as per
Documentation/networking/driver.rst:
| Quiescence
| ----------
|
| After the ndo_stop routine has been called, the hardware must
| not receive or transmit any data. All in flight packets must
| be aborted. If necessary, poll or wait for completion of
| any reset commands.
So it should be sufficient to ensure that later, when we zeroize
conduit->dsa_ptr, there will be no concurrent dsa_switch_rcv() call
on this conduit.
The addition of the netif_device_detach() function is to ensure that
ioctls, rtnetlinks and ethtool requests on the user ports no longer
propagate down to the driver - we're no longer prepared to handle them.
The race condition actually did not exist when commit 0650bf52b3
("net: dsa: be compatible with masters which unregister on shutdown")
first introduced dsa_switch_shutdown(). It was created later, when we
stopped unregistering the user interfaces from a bad spot, and we just
replaced that sequence with a racy zeroization of conduit->dsa_ptr
(one which doesn't ensure that the interfaces aren't up).
Reported-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Closes: https://lore.kernel.org/netdev/2d2e3bba17203c14a5ffdabc174e3b6bbb9ad438.camel@siemens.com/
Closes: https://lore.kernel.org/netdev/c1bf4de54e829111e0e4a70e7bd1cf523c9550ff.camel@siemens.com/
Fixes: ee534378f0 ("net: dsa: fix panic when DSA master device unbinds on shutdown")
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20240913203549.3081071-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
CONFIG_DRM_I915_USERFAULT_AUTOSUSPEND is an int, defaulting to 250. When
the wakeref is non-zero, it's either -1 or a dynamically allocated
pointer, depending on CONFIG_DRM_I915_DEBUG_RUNTIME_PM. It's likely that
the code works by coincidence with the bitwise AND, but with
CONFIG_DRM_I915_DEBUG_RUNTIME_PM=y, there's the off chance that the
condition evaluates to false, and intel_wakeref_auto() doesn't get
called. Switch to the intended logical AND.
v2: Use != to avoid clang -Wconstant-logical-operand (Nathan)
Fixes: ad74457a6b ("drm/i915/dgfx: Release mmap on rpm suspend")
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: stable@vger.kernel.org # v6.1+
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> # v1
Link: https://patchwork.freedesktop.org/patch/msgid/643cc0a4d12f47fd8403d42581e83b1e9c4543c7.1726680898.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 4c1bfe259e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If CREATE was successful but SMB2_OP_SET_REPARSE failed then remove the
intermediate object created by CREATE. Otherwise empty object stay on the
server when reparse call failed.
This ensures that if the creating of special files is unsupported by the
server then no empty file stay on the server as a result of unsupported
operation.
Fixes: 102466f303 ("smb: client: allow creating special files via reparse points")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
FCONT=1 means On FIFO error, the SAI will continue from the
same word that caused the FIFO error to set after the FIFO
warning flag has been cleared.
Set FCONT bit in control register to avoid the channel swap
issue after SAI xrun.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1727676508-22830-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_controller_is_target() check is missing for pm_runtime_disable()
in cdns_spi_remove(), add it.
Fixes: b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-4-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: d36ccd9f7e ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 43b6bf406c ("spi: imx: fix runtime pm support for !CONFIG_PM")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The device at 0xffd90000 is named SRU, both in the datasheet and SoC
DTSI. Fix the typo in the bindings to avoid the false positive report:
sound@ffd90000: reg-names:0: 'sru' is not one of ['scu', 'ssi', 'adg']
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240926113241.24060-2-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- When sched_ext is in bypass mode (e.g. while disabling the BPF scheduler),
it was using one DSQ to implement global FIFO scheduling as all it has to
do is guaranteeing reasonable forward progress. On multi-socket machines,
this can lead to live-lock conditions under certain workloads. Fixed by
splitting the queue used for FIFO scheduling per NUMA node. This required
several preparation patches.
- Hotplug tests on powerpc could reliably trigger deadlock while enabling a
BPF scheduler. This was caused by cpu_hotplug_lock nesting inside
scx_fork_rwsem and then CPU hotplug path trying to fork a new thread while
holding cpu_hotplug_lock. Fixed by restructuring locking in enable and
disable paths so that the two locks are not coupled. This required several
preparation patches which also fixed a couple other issues in the enable
path.
- A build fix for !CONFIG_SMP.
- Userspace tooling sync and updates.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCZvsB8A4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGW0cAP9LWESwNvszp0jDglg8kvS6tyHDLNQYLT99Dy4Q
NPE1OgD+KUKXuRBOhT3dc9dbwodmPtX2rq36QIgHhoGiPB9hew8=
=NH+o
-----END PGP SIGNATURE-----
Merge tag 'sched_ext-for-6.12-rc1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fixes from Tejun Heo:
- When sched_ext is in bypass mode (e.g. while disabling the BPF
scheduler), it was using one DSQ to implement global FIFO scheduling
as all it has to do is guaranteeing reasonable forward progress.
On multi-socket machines, this can lead to live-lock conditions under
certain workloads. Fixed by splitting the queue used for FIFO
scheduling per NUMA node. This required several preparation patches.
- Hotplug tests on powerpc could reliably trigger deadlock while
enabling a BPF scheduler.
This was caused by cpu_hotplug_lock nesting inside scx_fork_rwsem and
then CPU hotplug path trying to fork a new thread while holding
cpu_hotplug_lock.
Fixed by restructuring locking in enable and disable paths so that
the two locks are not coupled. This required several preparation
patches which also fixed a couple other issues in the enable path.
- A build fix for !CONFIG_SMP
- Userspace tooling sync and updates
* tag 'sched_ext-for-6.12-rc1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Remove redundant p->nr_cpus_allowed checker
sched_ext: Decouple locks in scx_ops_enable()
sched_ext: Decouple locks in scx_ops_disable_workfn()
sched_ext: Add scx_cgroup_enabled to gate cgroup operations and fix scx_tg_online()
sched_ext: Enable scx_ops_init_task() separately
sched_ext: Fix SCX_TASK_INIT -> SCX_TASK_READY transitions in scx_ops_enable()
sched_ext: Initialize in bypass mode
sched_ext: Remove SCX_OPS_PREPPING
sched_ext: Relocate check_hotplug_seq() call in scx_ops_enable()
sched_ext: Use shorter slice while bypassing
sched_ext: Split the global DSQ per NUMA node
sched_ext: Relocate find_user_dsq()
sched_ext: Allow only user DSQs for scx_bpf_consume(), scx_bpf_dsq_nr_queued() and bpf_iter_scx_dsq_new()
scx_flatcg: Use a user DSQ for fallback instead of SCX_DSQ_GLOBAL
tools/sched_ext: Receive misc updates from SCX repo
sched_ext: Add __COMPAT helpers for features added during v6.12 devel cycle
sched_ext: Build fix for !CONFIG_SMP
Like other Asus ExpertBook models the B2502CVA has its keybopard IRQ (1)
described as ActiveLow in the DSDT, which the kernel overrides to EdgeHigh
which breaks the keyboard.
Add the B2502CVA to the irq1_level_low_skip_override[] quirk table to fix
this.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217760
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240927141606.66826-4-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Like other Asus Vivobooks, the Asus Vivobook Go E1404GA has a DSDT
describing IRQ 1 as ActiveLow, while the kernel overrides to Edge_High.
$ sudo dmesg | grep DMI:.*BIOS
[ 0.000000] DMI: ASUSTeK COMPUTER INC. Vivobook Go E1404GA_E1404GA/E1404GA, BIOS E1404GA.302 08/23/2023
$ sudo cp /sys/firmware/acpi/tables/DSDT dsdt.dat
$ iasl -d dsdt.dat
$ grep -A 30 PS2K dsdt.dsl | grep IRQ -A 1
IRQ (Level, ActiveLow, Exclusive, )
{1}
There already is an entry in the irq1_level_low_skip_override[] DMI match
table for the "E1404GAB", change this to match on "E1404GA" to cover
the E1404GA model as well (DMI_MATCH() does a substring match).
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219224
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240927141606.66826-2-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit d2aaf19965 ("ACPI: resource: Add DMI quirks for ASUS Vivobook
E1504GA and E1504GAB") does exactly what the subject says, adding DMI
matches for both the E1504GA and E1504GAB.
But DMI_MATCH() does a substring match, so checking for E1504GA will also
match E1504GAB.
Drop the unnecessary E1504GAB entry since that is covered already by
the E1504GA entry.
Fixes: d2aaf19965 ("ACPI: resource: Add DMI quirks for ASUS Vivobook E1504GA and E1504GAB")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240927141606.66826-1-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- uprobes: fix kernel info leak via "[uprobes]" vma
Fix uprobes not to expose the uninitialized page for trampoline
buffer to user space, which can leak kernel info.
-----BEGIN PGP SIGNATURE-----
iQFOBAABCgA5FiEEh7BulGwFlgAOi5DV2/sHvwUrPxsFAmb6yK4bHG1hc2FtaS5o
aXJhbWF0c3VAZ21haWwuY29tAAoJENv7B78FKz8bME4H9ivH3PKLYd4tlz5WYBD6
EhcMhvlOVv6rD/l3LVZuh81o+TkObypWOaIVMeMJOTxWv0wEIYsNuQy/jzYWMB6L
gQpdrQtVb79kk0flf8feeZYebwNgCM7tOkq/dFaZJSDYd7Cb6QW4jroeSLs1oYFK
fulA4Tq2wrQwPpxF8docYZiBPpkz62uICP9eS0X2BUlWjzzHeDRny6uO0DW7SfJc
knNRmFZYPyW5Fovd4MF0iyaUMRduTt6B9bvtasu52F4WzwCyG2r7scm6UDAEJiV7
O77+Xq55KkkoZy3+xlZPQgyE1i/Uer5hX735dppu2CPQvhgZGfflNYNQUUUcGegu
/w==
=kLlc
-----END PGP SIGNATURE-----
Merge tag 'probes-fixes-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fix from Masami Hiramatsu:
- uprobes: fix kernel info leak via "[uprobes]" vma
Fix uprobes not to expose the uninitialized page for trampoline
buffer to user space, which can leak kernel info.
* tag 'probes-fixes-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
uprobes: fix kernel info leak via "[uprobes]" vma
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZvqoUgAKCRCRxhvAZXjc
oveLAQC952BB+giATJvX5lPz400g+MoDVlWiPdqAVbF0PCGRRwEA+/7TedOfOkQx
Df3iAzDXVbX/WvWYdZ/DyLp/r44WHAw=
=tGkE
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.12-rc2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"afs:
- Fix setting of the server responding flag
- Remove unused struct afs_address_list and afs_put_address_list()
function
- Fix infinite loop because of unresponsive servers
- Ensure that afs_retry_request() function is correctly added to the
afs_req_ops netfs operations table
netfs:
- Fix netfs_folio tracepoint handling to handle NULL mappings
- Add a missing folio_queue API documentation
- Ensure that netfs_write_folio() correctly advances the iterator via
iov_iter_advance()
- Fix a dentry leak during concurrent cull and cookie lookup
operations in cachefiles
pidfs:
- Correctly handle accessing another task's pid namespace"
* tag 'vfs-6.12-rc2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
netfs: Fix the netfs_folio tracepoint to handle NULL mapping
netfs: Add folio_queue API documentation
netfs: Advance iterator correctly rather than jumping it
afs: Fix the setting of the server responding flag
afs: Remove unused struct and function prototype
afs: Fix possible infinite loop with unresponsive servers
pidfs: check for valid pid namespace
afs: Fix missing wire-up of afs_retry_request()
cachefiles: fix dentry leak in cachefiles_open_file()
The name of the "load_address" objects has been modified, but the
corresponding entry in the gitignore file must be updated.
Update the load_address entry in the gitignore file to account for
the new names, adding an exception to keep on tracking load_address.c.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This executable is missing from the corresponding gitignore file.
Add unshare_test to the core gitignore list.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The macro MAX_PID_NS_LEVEL is never referenced in the code, so remove it.
Signed-off-by: Ba Jing <bajing@cmss.chinamobile.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
__fatal_error routine doesn't check strerror_r() return value,
which results in the following compile time warning:
posix_timers.c: In function ‘__fatal_error’:
posix_timers.c:31:9: warning: ignoring return value of ‘strerror_r’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
31 | strerror_r(errno, buf, sizeof(buf));
Fix this by adding a check for return value and error handling appropriate
for the GNU-specific strerror_r() in use in __fatal_error(). Check if
return string is null and handle accordingly.
From Linux strerror_r() manual page:
"The GNU-specific strerror_r() returns a pointer to a string containing
the error message. This may be either a pointer to a string that the
function stores in buf, or a pointer to some (immutable) static string
(in which case buf is unused). If the function stores a string in buf,
then at most buflen bytes are stored (the string may be truncated if
buflen is too small and errnum is unknown). The string always includes
a terminating null byte."
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: John Stultz <jstultz@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The rtctest requires the read permission on /dev/rtc0. The rtctest will
be skipped if the /dev/rtc0 is not readable.
Reviewed-by: Koba Ko <kobak@nvidia.com>
Reviewed-by: Matthew R. Ochs <mochs@nvidia.com>
Signed-off-by: Joseph Jang <jjang@nvidia.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
If the recv returns zero, or an error, then it doesn't matter if more
data has already been received for this buffer. A condition like that
should terminate the multishot receive. Rather than pass in the
collected return value, pass in whether to terminate or keep the recv
going separately.
Note that this isn't a bug right now, as the only way to get there is
via setting MSG_WAITALL with multishot receive. And if an application
does that, then -EINVAL is returned anyway. But it seems like an easy
bug to introduce, so let's make it a bit more explicit.
Link: https://github.com/axboe/liburing/issues/1246
Cc: stable@vger.kernel.org
Fixes: b3fdea6ecb ("io_uring: multishot recv")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reorganize kerneldoc parameter names to match the parameter
order in the function header.
Problems identified using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://patch.msgid.link/20240930112121.95324-5-Julia.Lawall@inria.fr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headset push button cannot work properly in case of the ALC257.
This patch reverted the previous commit to correct the side effect.
Fixes: ef9718b3d5 ("ALSA: hda/realtek: Fix noise from speakers on Lenovo IdeaPad 3 15IAU7")
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Link: https://patch.msgid.link/20240930105039.3473266-1-oder_chiou@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 087913e0ba.
It turned out that the original code was correct since the rq can only
change when there is no armed job for an entity.
This change here broke the logic since we only incremented the counter
for the first job, so revert it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930131451.536150-1-christian.koenig@amd.com
