The BO cleanup touches the GGTT and therefore requires the HW to be
available, so we need to use devm instead of drmm.
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1160
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240809231237.1503796-2-daniele.ceraolospurio@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 8d3a2d3d76)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This WA is applied while initializing the media GT, but it a primary
GT WA (because it modifies a register on the primary GT), so the XE_WA
macro is returning false even when the WA should be applied.
Fix this by using the primary GT in the macro.
Note that this WA only applies to PXP and we don't yet support that in
Xe, so there are no negative effects to this bug, which is why we didn't
see any errors in testing.
v2: use the primary GT in the macro instead of marking the WA as
platform-wide (Lucas, Matt).
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240807235333.1370915-1-daniele.ceraolospurio@intel.com
(cherry picked from commit e422c0bfd9)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Wa_15015404425 asks us to perform four "dummy" writes to a
non-existent register offset before every real register read.
Although the specific offset of the writes doesn't directly
matter, the workaround suggests offset 0x130030 as a good target
so that these writes will be easy to recognize and filter out in
debugging traces.
V5(MattR):
- Avoid negating an equality comparison
V4(MattR):
- Use writel and remove xe_reg usage
V3(MattR):
- Define dummy reg local to function
- Avoid tracing dummy writes
- Update commit message
V2:
- Add WA to 8/16/32bit reads also - MattR
- Corrected dummy reg address - MattR
- Use for loop to avoid mental pause - JaniN
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240709155606.2998941-1-tejas.upadhyay@intel.com
(cherry picked from commit 86c5b70a9c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Issuing the flush on top of an ongoing flush is not desirable.
Lets use lock to make it sequential.
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240710052750.3031586-1-tejas.upadhyay@intel.com
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
(cherry picked from commit 71733b8d7f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
workaround 14021402888 also applies to Xe2_LPG.
Replicate the existing entry to one specific for Xe2_LPG.
Signed-off-by: Bommu Krishnaiah <krishnaiah.bommu@intel.com>
Cc: Tejas Upadhyay <tejas.upadhyay@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703090754.1323647-1-krishnaiah.bommu@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 56ab698699)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This involves enabling l2 caching of host side memory access to VRAM
through the CPU BAR. The main fallout here is with display since VRAM
writes from CPU can now be cached in GPU l2, and display is never
coherent with caches, so needs various manual flushing. In the case of
fbc we disable it due to complications in getting this to work
correctly (in a later patch).
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703124338.208220-3-matthew.auld@intel.com
(cherry picked from commit 01570b4469)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We recently moved the teardown of the vgic part of a vcpu inside
a critical section guarded by the config_lock. This teardown phase
involves calling into kvm_io_bus_unregister_dev(), which takes the
kvm->srcu lock.
However, this violates the established order where kvm->srcu is
taken on a memory fault (such as an MMIO access), possibly
followed by taking the config_lock if the GIC emulation requires
mutual exclusion from the other vcpus.
It therefore results in a bad lockdep splat, as reported by Zenghui.
Fix this by moving the call to kvm_io_bus_unregister_dev() outside
of the config_lock critical section. At this stage, there shouln't
be any need to hold the config_lock.
As an additional bonus, document the ordering between kvm->slots_lock,
kvm->srcu and kvm->arch.config_lock so that I cannot pretend I didn't
know about those anymore.
Fixes: 9eb18136af ("KVM: arm64: vgic: Hold config_lock while tearing down a CPU interface")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20240819125045.3474845-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
If there were LPIs being mapped behind our back (i.e., between .start() and
.stop()), we would put them at iter_unmark_lpis() without checking if they
were actually *marked*, which is obviously not good.
Switch to use the xa_for_each_marked() iterator to fix it.
Cc: stable@vger.kernel.org
Fixes: 85d3ccc8b7 ("KVM: arm64: vgic-debug: Use an xarray mark for debug iterator")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240817101541.1664-1-yuzenghui@huawei.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
-----BEGIN PGP SIGNATURE-----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=2wc2
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk fix from Petr Mladek:
- Do not block printk on non-panic CPUs when they are dumping
backtraces
* tag 'printk-for-6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk/panic: Allow cpu backtraces to be written into ringbuffer during panic
These new trace points record xarray indices and the time of
endpoint registration and unregistration, to co-ordinate with
device removal events.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Nit: The built-in xa_limit_32b range starts at 0, but
XA_FLAGS_ALLOC1 configures the xarray's allocator to start at 1.
Adopt the more conventional XA_FLAGS_ALLOC because there's no
mechanical reason to skip 0.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the device's reference count is too high, the device completion
callback never fires.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Function bdev_get_queue() must not return NULL, so drop the check in
bdev_write_zeroes_sectors().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Link: https://lore.kernel.org/r/20240815163228.216051-3-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As reported in [0], we may get a hang when formatting a XFS FS on a RAID0
drive.
Commit 73a768d5f9 ("block: factor out a blk_write_zeroes_limit helper")
changed __blkdev_issue_write_zeroes() to read the max write zeroes
value in the loop. This is not safe as max write zeroes may change in
value. Specifically for the case of [0], the value goes to 0, and we get
an infinite loop.
Lift the limit reading out of the loop.
[0] https://lore.kernel.org/linux-xfs/4d31268f-310b-4220-88a2-e191c3932a82@oracle.com/T/#t
Fixes: 73a768d5f9 ("block: factor out a blk_write_zeroes_limit helper")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240815163228.216051-2-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Its possible that two threads call tcp_sk_exit_batch() concurrently,
once from the cleanup_net workqueue, once from a task that failed to clone
a new netns. In the latter case, error unwinding calls the exit handlers
in reverse order for the 'failed' netns.
tcp_sk_exit_batch() calls tcp_twsk_purge().
Problem is that since commit b099ce2602 ("net: Batch inet_twsk_purge"),
this function picks up twsk in any dying netns, not just the one passed
in via exit_batch list.
This means that the error unwind of setup_net() can "steal" and destroy
timewait sockets belonging to the exiting netns.
This allows the netns exit worker to proceed to call
WARN_ON_ONCE(!refcount_dec_and_test(&net->ipv4.tcp_death_row.tw_refcount));
without the expected 1 -> 0 transition, which then splats.
At same time, error unwind path that is also running inet_twsk_purge()
will splat as well:
WARNING: .. at lib/refcount.c:31 refcount_warn_saturate+0x1ed/0x210
...
refcount_dec include/linux/refcount.h:351 [inline]
inet_twsk_kill+0x758/0x9c0 net/ipv4/inet_timewait_sock.c:70
inet_twsk_deschedule_put net/ipv4/inet_timewait_sock.c:221
inet_twsk_purge+0x725/0x890 net/ipv4/inet_timewait_sock.c:304
tcp_sk_exit_batch+0x1c/0x170 net/ipv4/tcp_ipv4.c:3522
ops_exit_list+0x128/0x180 net/core/net_namespace.c:178
setup_net+0x714/0xb40 net/core/net_namespace.c:375
copy_net_ns+0x2f0/0x670 net/core/net_namespace.c:508
create_new_namespaces+0x3ea/0xb10 kernel/nsproxy.c:110
... because refcount_dec() of tw_refcount unexpectedly dropped to 0.
This doesn't seem like an actual bug (no tw sockets got lost and I don't
see a use-after-free) but as erroneous trigger of debug check.
Add a mutex to force strict ordering: the task that calls tcp_twsk_purge()
blocks other task from doing final _dec_and_test before mutex-owner has
removed all tw sockets of dying netns.
Fixes: e9bd0cca09 ("tcp: Don't allocate tcp_death_row outside of struct netns_ipv4.")
Reported-by: syzbot+8ea26396ff85d23a8929@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/0000000000003a5292061f5e4e19@google.com/
Link: https://lore.kernel.org/netdev/20240812140104.GA21559@breakpoint.cc/
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240812222857.29837-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building with gcc-5:
In function ‘decode_oa_format.isra.26’,
inlined from ‘xe_oa_set_prop_oa_format’ at drivers/gpu/drm/xe/xe_oa.c:1664:6:
././include/linux/compiler_types.h:510:38: error: call to ‘__compiletime_assert_1336’ declared with attribute error: FIELD_GET: mask is not constant
[...]
./include/linux/bitfield.h:155:3: note: in expansion of macro ‘__BF_FIELD_CHECK’
__BF_FIELD_CHECK(_mask, _reg, 0U, "FIELD_GET: "); \
^
drivers/gpu/drm/xe/xe_oa.c:1573:18: note: in expansion of macro ‘FIELD_GET’
u32 bc_report = FIELD_GET(DRM_XE_OA_FORMAT_MASK_BC_REPORT, fmt);
^
Fixes: b6fd51c621 ("drm/xe/oa/uapi: Define and parse OA stream properties")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729092634.2227611-1-geert+renesas@glider.be
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit f2881dfdaa)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We should unpin before evicting all memory, and repin after GT resume.
This way, we preserve the contents of the framebuffers, and won't hang
on resume due to migration engine not being restored yet.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: stable@vger.kernel.org # v6.8+
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240806105044.596842-3-maarten.lankhorst@linux.intel.com
Signed-off-by: Maarten Lankhorst,,, <maarten.lankhorst@linux.intel.com>
(cherry picked from commit cb8f81c175)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The fence lock is part of the queue, therefore in the current design
anything locking the fence should then also hold a ref to the queue to
prevent the queue from being freed.
However, currently it looks like we signal the fence and then drop the
queue ref, but if something is waiting on the fence, the waiter is
kicked to wake up at some later point, where upon waking up it first
grabs the lock before checking the fence state. But if we have already
dropped the queue ref, then the lock might already be freed as part of
the queue, leading to uaf.
To prevent this, move the fence lock into the fence itself so we don't
run into lifetime issues. Alternative might be to have device level
lock, or only release the queue in the fence release callback, however
that might require pushing to another worker to avoid locking issues.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
References: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2454
References: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2342
References: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2020
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240814110129.825847-2-matthew.auld@intel.com
(cherry picked from commit 7116c35aac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Only set tile->mmio.regs to NULL if not the root tile in tile_fini. The
root tile mmio regs is setup ealier in MMIO init thus it should be set
to NULL in mmio_fini.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240809232830.3302251-1-matthew.brost@intel.com
(cherry picked from commit 3396900aa2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The critical section which requires the VM dma-resv is the call
xe_lrc_create in __xe_exec_queue_init. Move this lock to
__xe_exec_queue_init holding it just around xe_lrc_create. Not only is
good practice, this also fixes a locking double of the VM dma-resv in
the error paths of __xe_exec_queue_init as xe_lrc_put tries to acquire
this too resulting in a deadlock.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240724152831.1848325-1-matthew.brost@intel.com
(cherry picked from commit 549dd786b6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
An empty sysctl table entry was inadvertently left behind for observation
sysctl. The breaks on 6.11 with the following errors:
[ 219.654850] sysctl table check failed: dev/xe/(null) procname is null
[ 219.654862] sysctl table check failed: dev/xe/(null) No proc_handler
Drop the empty entry.
Fixes: 63347fe031 ("drm/xe/uapi: Rename xe perf layer as xe observation layer")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2419
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240805062057.3547560-1-ashutosh.dixit@intel.com
(cherry picked from commit be1dec570b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Dell All In One (AIO) models released after 2017 may use a backlight
controller board connected to an UART.
In DSDT this uart port will be defined as:
Name (_HID, "DELL0501")
Name (_CID, EisaId ("PNP0501")
The Dell OptiPlex 7760 AIO has an ACPI device for one if its UARTs with
the above _HID + _CID. Loading the dell-uart-backlight driver shows that
there actually is a backlight controller board attached to the UART,
which reports a firmware version of "G&MX01-V15".
But the backlight controller board does not actually control the backlight
brightness and the GPU's native backlight control method does work.
Add a quirk to use the GPU's native backlight control method on this model.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2303936
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20240814190159.15650-4-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dell-uart-backlight driver supports backlight control on Dell All In
One (AIO) models using a backlight controller board connected to an UART.
In DSDT this uart port will be defined as:
Name (_HID, "DELL0501")
Name (_CID, EisaId ("PNP0501")
Now the first AIO has turned up which has not only the DSDT bits for this,
but also an actual controller attached to the UART, yet it is not using
this controller for backlight control.
Use the acpi_video_get_backlight_type() function from the ACPI video-detect
code to check if the dell-uart-backlight driver should actually be used.
This allows reusing the existing ACPI video-detect infra to override
the backlight control method on the commandline or with DMI quirks.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20240814190159.15650-3-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dell All In One (AIO) models released after 2017 use a backlight
controller board connected to an UART.
In DSDT this uart port will be defined as:
Name (_HID, "DELL0501")
Name (_CID, EisaId ("PNP0501")
Commit 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
has added support for this, but I neglected to tie this into
acpi_video_get_backlight_type().
Now the first AIO has turned up which has not only the DSDT bits for this,
but also an actual controller attached to the UART, yet it is not using
this controller for backlight control.
Add support to acpi_video_get_backlight_type() for a new dell_uart
backlight type. So that the existing infra to override the backlight
control method on the commandline or with DMI quirks can be used.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20240814190159.15650-2-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The sparse tool complains as follows:
drivers/iommu/iommufd/selftest.c:277:30: warning:
symbol 'dirty_ops' was not declared. Should it be static?
This symbol is not used outside of selftest.c, so marks it static.
Fixes: 266ce58989 ("iommufd/selftest: Test IOMMU_HWPT_ALLOC_DIRTY_TRACKING")
Link: https://patch.msgid.link/r/20240819120007.3884868-1-ruanjinjie@huawei.com
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Hangbin Liu says:
====================
selftests: Fix udpgro failures
There are 2 issues for the current udpgro test. The first one is the testing
doesn't record all the failures, which may report pass but the test actually
failed. e.g.
https://netdev-3.bots.linux.dev/vmksft-net/results/725661/45-udpgro-sh/stdout
The other one is after commit d7db7775ea ("net: veth: do not manipulate
GRO when using XDP"), there is no need to load xdp program to enable GRO
on veth device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit d7db7775ea ("net: veth: do not manipulate GRO when using
XDP"), there is no need to load XDP program to enable GRO. On the other
hand, the current test is failed due to loading the XDP program. e.g.
# selftests: net: udpgro.sh
# ipv4
# no GRO ok
# no GRO chk cmsg ok
# GRO ./udpgso_bench_rx: recv: bad packet len, got 1472, expected 14720
#
# failed
[...]
# bad GRO lookup ok
# multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
#
# ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
#
# failed
ok 1 selftests: net: udpgro.sh
After fix, all the test passed.
# ./udpgro.sh
ipv4
no GRO ok
[...]
multiple GRO socks ok
Fixes: d7db7775ea ("net: veth: do not manipulate GRO when using XDP")
Reported-by: Yi Chen <yiche@redhat.com>
Closes: https://issues.redhat.com/browse/RHEL-53858
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we only check the latest senders's exit code. If the receiver
report failed, it is not recoreded. Fix it by checking the exit code
of all the involved processes.
Before:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
0
After:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
1
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit 2e6506e1c4 ("mm/migrate: fix deadlock in
migrate_pages_batch() on large folios") has landed upstream, large
folios can be safely enabled for compressed inodes since all
prerequisites have already landed in 6.11-rc1.
Stress tests has been running on my fleet for over 20 days without any
regression. Additionally, users [1] have requested it for months.
Let's allow large folios for EROFS full cases upstream now for wider
testing.
[1] https://lore.kernel.org/r/CAGsJ_4wtE8OcpinuqVwG4jtdx6Qh5f+TON6wz+4HMCq=A2qFcA@mail.gmail.com
Cc: Barry Song <21cnbao@gmail.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
[ Gao Xiang: minor commit typo fixes. ]
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240819025207.3808649-1-hsiangkao@linux.alibaba.com
If the WCN module is powered up before linux boots and the ath11k driver
probes at the same time as the power sequencing driver, we may end up
driving the wlan-enable GPIO low in the latter, breaking the start-up of
the WLAN module. Request the wlan-enable GPIO as-is so that if the WLAN
module is already starting/started, we leave it alone.
Fixes: 2f1630f437 ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets")
Reported-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20240813190751.155035-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The old quirk combination sometimes cause a laggy keyboard after boot. With
the new quirk the initial issue of an unresponsive keyboard after s3 resume
is also fixed, but it doesn't have the negative side effect of the
sometimes laggy keyboard.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240104183118.779778-3-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On s3 resume the i8042 driver tries to restore the controller to a known
state by reinitializing things, however this can confuse the controller
with different effects. Mostly occasionally unresponsive keyboards after
resume.
These issues do not rise on s0ix resume as here the controller is assumed
to preserved its state from before suspend.
This patch adds a quirk for devices where the reinitialization on s3 resume
is not needed and might be harmful as described above. It does this by
using the s0ix resume code path at selected locations.
This new quirk goes beyond what the preexisting reset=never quirk does,
which only skips some reinitialization steps.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240104183118.779778-2-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are checking cp_irq_count from the wrong hdcp structure which
ends up giving timed out errors. We only increment the cp_irq_count
of the primary connector's hdcp structure but here in case of
multidisplay setup we end up checking the secondary connector's hdcp
structure, which will not have its cp_irq_count incremented. This leads
to a timed out at CP_IRQ error even though a CP_IRQ was raised. Extract
it from the correct intel_hdcp structure.
--v2
-Explain why it was the wrong hdcp structure [Jani]
Fixes: 8c9e4f68b8 ("drm/i915/hdcp: Use per-device debugs")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240809114127.3940699-2-suraj.kandpal@intel.com
(cherry picked from commit dd92590263)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
- Use i_size instead of i_size_read() due to immutable fses;
- Get rid of an unneeded goto since erofs_fill_dentries() also works;
- Remove unnecessary lines.
Signed-off-by: Hongzhen Luo <hongzhen@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240801112622.2164029-1-hongzhen@linux.alibaba.com
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Replace the deprecated one-element arrays with flexible-array members
in the structs filesystem_attribute_info and filesystem_device_info.
There are no binary differences after this conversion.
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
There are a couple of spelling mistakes in the documentation. This patch
fixes them.
Signed-off-by: Victor Timofei <victor@vtimothy.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
If there is ->PreviousSessionId field in the session setup request,
The session of the previous connection should be destroyed.
During this, if the smb2 operation requests in the previous session are
being processed, a racy issue could happen with ksmbd_destroy_file_table().
This patch sets conn->status to KSMBD_SESS_NEED_RECONNECT to block
incoming operations and waits until on-going operations are complete
(i.e. idle) before desctorying the previous session.
Fixes: c8efcc7861 ("ksmbd: add support for durable handles v1/v2")
Cc: stable@vger.kernel.org # v6.6+
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-25040
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
rsp buffer is allocated larger than spnego_blob from
smb2_allocate_rsp_buf().
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Mandatory locking is enforced for cached reads, which violates
default posix semantics, and also it is enforced inconsistently.
This affected recent versions of libreoffice, and can be
demonstrated by opening a file twice from the same client,
locking it from handle one and trying to read from it from
handle two (which fails, returning EACCES).
There is already a mount option "forcemandatorylock"
(which defaults to off), so with this change only when the user
intentionally specifies "forcemandatorylock" on mount will we
break posix semantics on read to a locked range (ie we will
only fail in this case, if the user mounts with
"forcemandatorylock").
An earlier patch fixed the write path.
Fixes: 85160e03a7 ("CIFS: Implement caching mechanism for mandatory brlocks")
Cc: stable@vger.kernel.org
Cc: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Reported-by: abartlet@samba.org
Reported-by: Kevin Ottens <kevin.ottens@enioka.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Here are 2 driver fixes for regressions from 6.11-rc1 due to the driver
core change making a structure in a driver core callback const. These
were missed by all testing EXCEPT for what Bart happened to be running,
so I appreciate the fixes provided here for some odd/not-often-used
driver subsystems that nothing else happened to catch.
Both of these fixes have been in linux-next all week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZsIWNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylHBgCdGDGhaQp4W/dLejZBeMtuGLILTcoAnRm7/Aj8
U/uR4ukttCXjfvjlalxi
=t+bl
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver fixes for regressions from 6.11-rc1 due to the
driver core change making a structure in a driver core callback const.
These were missed by all testing EXCEPT for what Bart happened to be
running, so I appreciate the fixes provided here for some
odd/not-often-used driver subsystems that nothing else happened to
catch.
Both of these fixes have been in linux-next all week with no reported
issues"
* tag 'driver-core-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
mips: sgi-ip22: Fix the build
ARM: riscpc: ecard: Fix the build
Here are some small char/misc fixes for 6.11-rc4 to resolve reported
problems. Included in here are:
- fastrpc revert of a change that broke userspace
- xillybus fixes for reported issues
Half of these have been in linux-next this week with no reported
problems, I don't know if the last bit of xillybus driver changes made
it in, but they are "obviously correct" so will be safe :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZsIT4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymYQACfeV6tIMHlHSVS9VSbiXHJAovjvFEAoLQvuvBS
0dN1Q4iYF+5Sy4JWAZb/
=ztLK
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc fixes from Greg KH:
"Here are some small char/misc fixes for 6.11-rc4 to resolve reported
problems. Included in here are:
- fastrpc revert of a change that broke userspace
- xillybus fixes for reported issues
Half of these have been in linux-next this week with no reported
problems, I don't know if the last bit of xillybus driver changes made
it in, but they are 'obviously correct' so will be safe :)"
* tag 'char-misc-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
char: xillybus: Check USB endpoints when probing device
char: xillybus: Refine workqueue handling
Revert "misc: fastrpc: Restrict untrusted app to attach to privileged PD"
char: xillybus: Don't destroy workqueue from work item running on it
