Rewrite a small section to clarify the reset operation of interrupts
already configured by ATF that we want to handle in the driver. This
will simplify the introduction of System Error Interrupts support.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_domain structure has an host_data pointer that just stores
private data. It is meant to not be touched by the IRQ core. However,
when it comes to MSI, the MSI layer adds its own private data there
with a structure that also has a host_data pointer.
Because this IRQ domain is an MSI domain, to access private data we
should do a d->host_data->host_data, also wrapped as
'platform_msi_get_host_data()'.
This bug was lying there silently because the 'icu' structure retrieved
this way was just called by dev_err(), only producing a
'(NULL device *):' output on the console.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The PDC irqchp can convert a falling edge or level low interrupt to a
rising edge or level high interrupt at the GIC. We just need to setup
the GIC correctly. Set up the interrupt type for the IRQ_TYPE_EDGE_BOTH
as IRQ_TYPE_EDGE_RISING at the GIC.
Fixes: f55c73aef890 ("irqchip/pdc: Add PDC interrupt controller for QCOM SoCs")
Reported-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the LPI tables have been reserved with the EFI reservation
mechanism, we assume that these tables are safe to use even
when we find the redistributors to have LPIs enabled at
boot time, meaning that kexec can now work with GICv3.
You're welcome.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Upon enabling a redistributor, let's register the allocated tables
with the EFI table that tracks the memory reservations.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If booting with LPIs enabled, all the redistributors must have the
exact same property table. No ifs, no buts.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If using a kdump kernel, and that we cannot disable LPIs to install
our own tables, let's switch to using the already allocated tables.
This means that we'll change some of the initial kernel's memory,
but at least we'll be able to have LPIs in this secondary kernel.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to cope with kexec and GICv3, let's try and spot when
we're booting with LPIs already enabled, and the tables already
programmed into the redistributors.
This code is currently guarded by a predicate that is always false,
meaning this is not functionnal just yet.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're currently only tracking the page allocated to contain the
property table by its struct page. In the future, it is going to
be convenient to track both PA and VA for that page instead. Let's
do that.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pending tables for the redistributors are currently allocated
one at a time as each CPU boots. This is causing some grief
for Linux/RT (allocation from within a CPU hotplug notifier is
frown upon).
Let's move this allocation to take place at init time, when we
only have a single CPU. It means we're allocating memory for CPUs
that are not online yet, but most system will boot all of their
CPUs anyway, so that's not completely wasted.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're going to reuse some pre-allocated memory for the property
table, split out the zeroing of that table into a separate function
for later use.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
LPI_PENDING_SZ is always used in conjunction with a max(), which doesn't
make much sense, since we're guaranteed that LPI_PENDING_SZ is already
aligned to 64K. Let's remove it.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently initialize the LPIs (and the ITS) fairly early, even
before the SMP support and the CPU interface. This is a bit odd
(as LPIs are not exactly crutial for the early boot process),
and is going to cause issues when reorganizing the probing code.
Let's move this initialization later.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit fe8e93504ce8 ("irqchip/gic-v3-its: Use full range of LPIs"), removes
the cap for lpi_id_bits, which causes the following warning to trigger on a
QDF2400 server:
WARNING: CPU: 0 PID: 0 at mm/page_alloc.c:4066 __alloc_pages_nodemask
...
Call trace:
__alloc_pages_nodemask+0x2d8/0x1188
alloc_pages_current+0x8c/0xd8
its_allocate_prop_table+0x5c/0xb8
its_init+0x220/0x3c0
gic_init_bases+0x250/0x380
gic_acpi_init+0x16c/0x2a4
In its_alloc_lpi_tables(), lpi_id_bits is 24 in QDF2400. The allocation in
allocate_prop_table() tries therefore to allocate 16M (order 12 if
pagesize=4k), which triggers the warning.
As said by MarcL
Capping lpi_id_bits at 16 (which is what we had before) is plenty,
will save a some memory, and gives some margin before we need to push
it up again.
Bring the upper limit of lpi_id_bits back to prevent
Fixes: fe8e93504ce8 ("irqchip/gic-v3-its: Use full range of LPIs")
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jia He <jia.he@hxt-semitech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lkml.kernel.org/r/1535432006-2304-1-git-send-email-jia.he@hxt-semitech.com
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
Var "addr" type incorrect.
It have interrupt controler register address.
Type of void __iomem is correct.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
If an xtensa core provides an additional IRQ controller it should be
treated as a separate piece of hardware and be driven by an irqchip
driver.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Although GICv3 doesn't directly offers support for wake-up interrupts
and relies on external HW for this, it shouldn't prevent the driver
for such HW from doing it work.
Let's set the required flags on the irq_chip structures.
Reported-by: Lina Iyer <ilina@codeaurora.org>
Tested-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Replace the two separate calls for setting the irq handler and data with
a single irq_set_chained_handler_and_data() call.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This tag contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make it
to userspace. Support for three devices has been added:
* Support for the ISA-mandated timers on RISC-V systems.
* Support for the ISA-mandated first-level interrupt controller on
RISC-V systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
* Support for SiFive's platform-level interrupt controller, which talks
to the actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
* Build fixes for various configurations
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary for
some 32-bit configurations.
* !SMP && PERF_EVENTS
* Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
* Fixes to ptrace(), which while not being sufficient to fully make GDB
work are at least sufficient to get simple GDB tasks to work.
* Early printk support via RISC-V's architecturally mandated SBI console
device.
* A fix to our early debug trap handler to ensure it's always aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for me,
and before this morning's rebase (from 4.18-rc8 to 4.18) it booted on
the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the new
drivers in shape!
-----BEGIN PGP SIGNATURE-----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=PfnC
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make
it to userspace. Support for three devices has been added:
- the ISA-mandated timers on RISC-V systems.
- the ISA-mandated first-level interrupt controller on RISC-V
systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
- SiFive's platform-level interrupt controller, which talks to the
actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
- build fixes for various configurations:
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary
for some 32-bit configurations.
* !SMP && PERF_EVENTS
- Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
- Fixes to ptrace(), which while not being sufficient to fully make
GDB work are at least sufficient to get simple GDB tasks to work.
- Early printk support via RISC-V's architecturally mandated SBI
console device.
- A fix to our early debug trap handler to ensure it's always
aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for
me, and before this morning's rebase (from 4.18-rc8 to 4.18) it booted
on the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the
new drivers in shape!"
* tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
dt-bindings: interrupt-controller: SiFive Plaform Level Interrupt Controller
dt-bindings: interrupt-controller: RISC-V local interrupt controller
RISC-V: Fix !CONFIG_SMP compilation error
irqchip: add a SiFive PLIC driver
RISC-V: Add the directive for alignment of stvec's value
clocksource: new RISC-V SBI timer driver
RISC-V: implement low-level interrupt handling
RISC-V: add a definition for the SIE SEIE bit
RISC-V: remove INTERRUPT_CAUSE_* defines from asm/irq.h
RISC-V: simplify software interrupt / IPI code
RISC-V: remove timer leftovers
RISC-V: Add early printk support via the SBI console
RISC-V: Don't increment sepc after breakpoint.
RISC-V: implement __lshrti3.
RISC-V: Use KBUILD_CFLAGS instead of KCFLAGS when building the vDSO
Add a driver for the SiFive implementation of the RISC-V Platform Level
Interrupt Controller (PLIC). The PLIC connects global interrupt sources
to the local interrupt controller on each hart.
This driver is based on the driver in the RISC-V tree from Palmer Dabbelt,
but has been almost entirely rewritten since, and includes many fixes
from Atish Patra.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
[Binding update by Palmer]
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
irq_data->hwirq is unsigned long. This fixes GCC warning:
drivers/irqchip/irq-s3c24xx.c: In function 's3c_irqext0_type':
drivers/irqchip/irq-s3c24xx.c:253:19: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if ((data->hwirq >= 0) && (data->hwirq <= 3)) {
^~
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If there are any errors in stm32_exti_host_init() then it leads to a
NULL dereference in the callers. The function should clean up after
itself.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When compiling bmips with SMP disabled, the build fails with:
drivers/irqchip/irq-bcm7038-l1.o: In function `bcm7038_l1_cpu_offline':
drivers/irqchip/irq-bcm7038-l1.c:242: undefined reference to `irq_set_affinity_locked'
make[5]: *** [vmlinux] Error 1
Fix this by adding and setting bcm7038_l1_cpu_offline only when actually
compiling for SMP. It wouldn't have been used anyway, as it requires
CPU_HOTPLUG, which in turn requires SMP.
Fixes: 34c535793bcb ("irqchip/bcm7038-l1: Implement irq_cpu_offline() callback")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- GICv3 ITS LPI allocation revamp
- GICv3 support for hypervisor-enforced LPI range
- GICv3 ITS conversion to raw spinlock
-----BEGIN PGP SIGNATURE-----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=gKw8
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- GICv3 ITS LPI allocation revamp
- GICv3 support for hypervisor-enforced LPI range
- GICv3 ITS conversion to raw spinlock
The its_lock lock is held while a new device is added to the list and
during setup while the CPU is booted. Even on -RT the CPU-bootup is
performed with disabled interrupts.
Make its_lock a raw_spin_lock_t.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Allocating a minimum of 32 LPIs per PCI device, let's reduce it to
be just 1, as most devices do not need that many interrupts.
We still have to special-case DevID 0, as there is plenty of broken
HW around where the PCI RID is not presented as a DevID to the ITS,
and all the devices are presented as DevID 0. In this case, we keep
the 32 minimal allocation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The interrupt controller of the JZ4725B works the same way as the other
JZ SoCs from Ingenic; so we just add a new compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch fixes a datasheet issue, in the draft version the "exti0"
was not connected whereas is it.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A recent extension to the GIC architecture allows a hypervisor to
arbitrarily reduce the number of LPIs available to a guest, no
matter what the GIC says about the valid range of IntIDs.
Let's factor in this information when computing the number of
available LPIs
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of exposing the GIC distributor IntID field in the rdist
structure that is passed to the ITS, let's replace it with a
copy of the whole GICD_TYPER register. We are going to need
some of this information at a later time.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At the moment, the core ITS driver imposes the allocation to be
in chunks of 32. As we want to relax this on a per bus basis, let's
move the the the allocation constraints to each bus.
No functionnal change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we used to represent the LPI range using a bitmap, we were reducing
the number of LPIs to at most 64k in order to preserve memory.
With our new allocator, there is no such need, as dealing with 2^16
or 2^32 LPIs takes the same amount of memory.
So let's use the number of IntID bits reported by the GIC instead of
an arbitrary limit.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Our current LPI allocator relies on a bitmap, each bit representing
a chunk of 32 LPIs, meaning that each device gets allocated LPIs
in multiple of 32. It served us well so far, but new use cases now
require much more finer grain allocations, down the the individual
LPI.
Given the size of the IntID space (up to 32bit), it isn't practical
to continue using a bitmap, so let's use a different data structure
altogether.
We switch to a list, where each element represent a contiguous range
of LPIs. On allocation, we simply grab the first group big enough to
satisfy the allocation, and substract what we need from it. If the
group becomes empty, we just remove it. On freeing interrupts, we
insert a new group of interrupt in the list, sort it and fuse the
adjacent groups.
This makes freeing interrupt much more expensive than allocating
them (an unusual behaviour), but that's fine as long as we consider
that freeing interrupts is an extremely rare event.
We still allocate interrupts in blocks of 32 for the time being,
but subsequent patches will relax this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enabling LPIs was made a lot stricter recently, by checking that they are
disabled before enabling them. By doing so, the CPU hotplug case was missed
altogether, which leaves LPIs enabled on hotplug off (expecting the CPU to
eventually come back), and won't write a different value anyway on hotplug
on.
So skip that check if that particular case is detected
Fixes: 6eb486b66a30 ("irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling")
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lkml.kernel.org/r/20180622095254.5906-8-marc.zyngier@arm.com
Similarily to the SYNC operation, it must be verified that the VPE
targetted by a VLPI is backed by a valid collection in the GIC driver data
structures.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-7-marc.zyngier@arm.com
It is possible, under obscure circumstances, to convince the ITS driver to
emit a SYNC operation that targets a collection that is not bound to any
redistributor (and the target_address field is zero) because the
corresponding CPU has not been seen yet (the system has been booted with
max_cpus="something small").
If the ITS is using the linear CPU number as the target, this is not a big
deal, as we just end-up issuing a SYNC to CPU0. But if the ITS requires the
physical address of the redistributor (with GITS_TYPER.PTA==1), we end-up
asking the ITS to write to the physical address zero, which is not exactly
a good idea (there has been report of the ITS locking up). This should of
course never happen, but hey, this is SW...
In order to avoid the above disaster, let's track which collections have
been actually initialized, and let's not generate a SYNC if the collection
hasn't been properly bound to a redistributor. Take this opportunity to
spit our a warning, in the hope that someone may report the issue if it
arrises again.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-6-marc.zyngier@arm.com
On a NUMA system, if an ITS is local to an offline node, the ITS driver may
pick an offline CPU to bind the LPI. In this case, pick an online CPU (and
the first one will do).
But on some systems, binding an LPI to non-local node CPU may cause
deadlock (see Cavium erratum 23144). In this case, just fail the activate
and return an error code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622095254.5906-5-marc.zyngier@arm.com
On failing to allocate the required SPIs, the actual number of interrupts
should be freed and not its log2 value.
Fixes: de337ee30142 ("irqchip/gic-v2m: Add PCI Multi-MSI support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-4-marc.zyngier@arm.com
The ls-scfs-msi driver is not dealing with the effective affinity
as it should. Let's fix that, and make it clear that the effective
affinity is restricted to a single CPU. Also prevent the driver from
messing with the internals of the affinity setting infrastructure.
Reported-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-3-marc.zyngier@arm.com
