The internal DIF emulation was not honoring se_cmd->prot_checks for
the WRPROTECT/RDPROTECT == 0x3 case, so sbc_dif_v1_verify() has been
updated to follow which checks have been calculated based on
WRPROTECT/RDPROTECT in sbc_set_prot_op_checks().
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In sbc_check_prot(), if PROTECT is non-zero for a backend device with
DIF disabled, and sess_prot_type is not set go ahead and return
INVALID_CDB_FIELD.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The following incremental patch saves the current sess_prot_type into
se_node_acl, and will always reset sess_prot_type if a previous saved
value exists. So the PI setting for the fabric's session with backend
devices not supporting PI is persistent across session restart.
(Fix se_node_acl dereference for discovery sessions - DanCarpenter)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The scatterlist for protection information which is passed to
sbc_dif_verify_read() or sbc_dif_verify_write() requires that
neighboring scatterlist entries are contiguous or chained so that they
can be iterated by sg_next().
However, the protection information for RD-MCP backends could be located
in the multiple scatterlist arrays when the ramdisk space is too large.
So if the read/write request straddles this boundary, sbc_dif_verify_read()
or sbc_dif_verify_write() can't iterate all scatterlist entries.
This problem can be fixed by chaining protection information scatterlist
at creation time. For the architectures which don't support sg chaining
(i.e. !CONFIG_ARCH_HAS_SG_CHAIN), fix it by allocating temporary
scatterlist if needed.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@dev.mellanox.co.il>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The flag SCF_ACK_KREF is only set but never tested. Hence remove
this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Avoid that sparse complains about context imbalances.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.
It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.
Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.
This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This fixes a oops due to a double list add when adding a reject PDU for
iscsit_allocate_iovecs allocation failures. The cmd has already been
added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call
iscsit_reject_cmd.
Note that for ERL0 the reject PDU is not actually sent, so this patch
is not completely tested. Just verified we do not oops. The problem is the
add reject functions return -1 which is returned all the way up to
iscsi_target_rx_thread which for ERL0 will drop the connection.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drop unused argument & return value and consolidate a duplicate assignment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Factor out code duplication in rd_execute_rw() into a helper function
rd_do_prot_rw(). This change is required to minimize the forthcoming
fix in rd_do_prot_rw().
(Fix up v4.1 for-next fuzz - nab)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sagi Grimberg <sagig@dev.mellanox.co.il>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently, for example, mkdir "tpgt_xyz" doesn't return error.
mkdir /sys/kernel/config/target/loopback/naa.60014055f195952b/tpgt_xyz
Replace obsoleted simple_strtoul with kstrtoul and check the conversion.
Signed-off-by: Ming Lin <mlin@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates iscsi/iser-target to add a new fabric_prot_type
TPG attribute for iser-target, used for controlling LLD level
protection into LIO when the backend device does not support T10-PI.
This is required for ib_isert to enable WRITE_STRIP + READ_INSERT
hardware offloads.
It's disabled by default and controls which se_sesion->sess_prot_type
are set at iscsi_target_locate_portal() session registration time.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates loopback to add a new fabric_prot_type TPG attribute,
used for controlling LLD level protection into LIO when the backend
device does not support T10-PI.
Also, go ahead and set DIN_PASS + DOUT_PASS so target-core knows that
it will be doing any WRITE_STRIP and READ_INSERT operations.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that RAMDISK only attempts to use backend DIF emulation
when it's actually enabled at device level.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that IBLOCK only attempts to use backend DIF emulation
when it's actually enabled at device level.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that FILEIO only attempts to use backend DIF emulation
when it's actually enabled at device level.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds READ_INSERT support in target_read_prot_action() that
invokes sbc_dif_generate() when LIO is responsible for generating the
outgoing T10-PI.
Required for supporting fabrics that exchange protection information,
and would like to function with un-protected devices.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves the existing target_complete_ok_work() check for
cmd->prot_op into it's own function, so it's easier to add future
support for READ INSERT.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds WRITE_STRIP support in target_write_prot_action() that
invokes sbc_dif_verify_write() for checking T10-PI metadata before
submitting the I/O to a backend driver.
Upon verify failure, the specific sense code is propigated up the
failure path up to transport_generic_request_failure().
Also, update sbc_dif_verify_write() to only perform the subsequent
protection metadata copy when a valid *sg is passed.
(Use ilog2 instead of division and unlikely for pi_err - Sagi)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves the existing target_execute_cmd() check for
cmd->prot_op into it's own function, so it's easier to add
future support for WRITE STRIP.
(Use better target_write_prot_action name - Sagi)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates standard INQUIRY, INQUIRY EVPD=0x86, READ_CAPACITY_16
and control mode pages to use se_sess->sess_prot_type when determing which
type of T10-PI related feature bits can be exposed.
This is required for fabric sessions supporting T10-PI metadata to
backend devices that don't have protection enabled.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new target_core_fabric_ops callback for allowing fabric
drivers to expose a TPG attribute for signaling when a T10-PI protected
fabric wants to function with an un-protected device without T10-PI.
This specifically is to allow LIO to perform WRITE_STRIP + READ_INSERT
operations when functioning with non T10-PI enabled devices, seperate
from any available hw offloads the fabric supports.
This is done using a new se_sess->sess_prot_type that is set at fabric
session creation time based upon the TPG attribute. It currently cannot
be changed for individual sessions after initial creation.
Also, update existing target_core_sbc.c code to honor sess_prot_type when
setting up cmd->prot_op + cmd->prot_type assignments.
(Add unlikely and !! boolean conversion in sbc_check_prot - Sagi)
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes existing DIF emulation to check the command descriptor's
prot_type, instead of what the backend device is exposing in pi_prot_type.
Since this value is already set in sbc_check_prot(), go ahead and use it to
allow protected fabrics to function with unprotected devices.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
"The domainname can be specified as either a DNS host name, a
dotted-decimal IPv4 address, or a bracketed IPv6 address as specified
in [RFC2732]."
See https://bugzilla.redhat.com/show_bug.cgi?id=1206868
Reported-by: Kyle Brantley <kyle@averageurl.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Before 4.0, reading attrib/emulate_fua_write has returned 1. Saved
configs created on a pre-4.0 kernel will try to write that back when
restoring LIO configuration. This should succeed with no effect,
and issue a warning.
See https://bugzilla.redhat.com/show_bug.cgi?id=1206184
Reported-by: Yanko Kaneti <yaneti@declera.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should not declare extrnal .c symbols in C files to make sure they
match the actual prototype, and sparse correctly warns about this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix AllRegistrants reservations in register_and_move() function where
the code didn't handle all of the registered devices as reservation
holders, resulting in the wrong warning message being displayed.
At the same time, introduce a helper function named
'is_reservation_holder()' that properly checks if a device is a
reservation holder, taking into account the reservation type. This
function cleans up the code and improves readability.
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Vangelis Koukis <vkoukis@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that iscsi_conn allocates new [rx,tx] threads using kthread.h
primitives on the fly, and kthread_stop() is called directly during
connection shutdown, it's time to go ahead and drop iscsi_target_tq.c
legacy code.
The use of multiple struct completion in iscsi_activate_thread_set()
has been proven to cause issues during repeated iser login/logout.
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts iscsi-target code to use modern kthread.h API
callers for creating RX/TX threads for each new iscsi_conn descriptor,
and releasing associated RX/TX threads during connection shutdown.
This is done using iscsit_start_kthreads() -> kthread_run() to start
new kthreads from within iscsi_post_login_handler(), and invoking
kthread_stop() from existing iscsit_close_connection() code.
Also, convert iscsit_logout_post_handler_closesession() code to use
cmpxchg when determing when iscsit_cause_connection_reinstatement()
needs to sleep waiting for completion.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL;
@@
-EXPORT_SYMBOL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the fabric module autoload failures from
pr_err to pr_debug in target_core_register_fabric() code, to
reduce the amount of noise during normal operation.
Reported-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdbf74a7d8fe0f0a44e85da1ed5975946
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reverts commit 72859d91d93319c00a18c29f577e56bf73a8654a.
The original patch was wrong, iscsit_close_connection() still needs
to release iscsi_conn during both normal + exception IN_LOGOUT status
with ib_isert enabled.
The original OOPs is due to completing conn_logout_comp early within
iscsit_close_connection(), causing isert_wait4logout() to complete
instead of waiting for iscsit_logout_post_handler_*() to be called.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that incoming FUA=1 bit check is enforced for backends with FUA or
WCE disabled, go ahead and disallow the changing of related backend
attributes when active fabric exports exist.
This is required to avoid potential failures with existing initiator
LUN registrations that have been previously created with FUA=1.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch exposes a new ../iscsi/$IQN/$TPGT/dynamic_sessions attribute
to dump the currently active sessions by iSCSI InitiatorName that have
been created with dynamically generated se_node_acls.
This information is useful so that user-space can optionally perform
dynamic -> explicit NodeACL conversion based on $INITIATOR_WWPN.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new helper function that can be used by fabric driver
TPG attributes for dumping the list of active sessions with a dynamically
generated se_node_acl. (generate_node_acl=1).
It prints one se_node_acl->initiatorname per line, up to PAGE_SIZE which
is due to the current limitiation of single page attribute output within
sysfs and configfs code.
Note that if a session is referencing a explicit NodeACL, the InitiatorName
will not appear within dynamic_sessions output.
Reported-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the new bio_vec backed iov_iter helpers we can simply set up
on bio_vec per LBA, all pointing to the same initiator-supplied
buffer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
