There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Yu Jiahua <yujiahua1@huawei.com>
Link: https://lore.kernel.org/r/20210616034826.37276-1-yujiahua1@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Caught this when looking at alpha-pll code. Untested but it is clear that
this was intended to write to PLL_CAL_L_VAL and not PLL_ALPHA_VAL.
Fixes: 691865bad627 ("clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20210609022852.4151-1-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the camera clock controller found on SM8250.
Based on the downstream driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://lore.kernel.org/r/20210609022051.2171-4-jonathan@marek.ca
[sboyd@kernel.org: Add UL to avoid decimal problems]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add device tree bindings for camera clock controller for
Qualcomm Technology Inc's SM8250 SoC.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20210609022051.2171-3-jonathan@marek.ca
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix gcc '-Wunused-const-variable' warnings:
drivers/clk/qcom/gcc-mdm9607.c:122:37: warning: 'gcc_xo_gpll0_gpll1'
defined but not used [-Wunused-const-variable=]
drivers/clk/qcom/gcc-mdm9607.c:116:32: warning: 'gcc_xo_gpll0_gpll1_map'
defined but not used [-Wunused-const-variable=]
drivers/clk/qcom/gcc-mdm9607.c:42:37: warning: 'gcc_xo_sleep' defined
but not used [-Wunused-const-variable=]
drivers/clk/qcom/gcc-mdm9607.c:37:32: warning: 'gcc_xo_sleep_map'
defined but not used [-Wunused-const-variable=]
Let's remove them.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/r/20210609061848.87415-1-pulehui@huawei.com
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add compatible for rpm smd clocks, PMIC and bus clocks which are required
on MSM8226 for clients to vote on.
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20210605104040.12960-1-bartosz.dudziak@snejp.pl
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Modify existing MSM8974 driver to support MSM8226 SoC. Override frequencies
which are different in this older chip. Register all the clocks to the
framework for the clients to be able to request for them.
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20210418122909.71434-3-bartosz.dudziak@snejp.pl
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add compatible device strings and the include files for the MSM8226 GCC.
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20210418122909.71434-2-bartosz.dudziak@snejp.pl
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the clocks supported in global clock controller, which clock the
peripherals like BLSPs, SDCC, USB, MDSS etc. Register all the clocks
to the clock framework for the clients to be able to request for them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Link: https://lore.kernel.org/r/20210605121040.282053-2-martin.botka@somainline.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sboyd@kernel.org: Mark gcc_sm6125_hws array static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is a requirement to support 52MHz for qup clocks for bluetooth
usecase, thus update the frequency table to support the frequency.
Fixes: a3cc092196ef ("clk: qcom: Add Global Clock controller (GCC) driver for SC7280")
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1624449471-9984-1-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
AM64 has 9 instances of EPWM modules. And each instance has a clk to
Timer-Base sub-module that can be controlled by Control module. Update
the driver with all the 9 instance of clocks associated to
ti,am64-epwm-tbclk.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210528045743.16537-3-lokeshvutla@ti.com
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Add support for the new RZ/G2L SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYMMqWQAKCRCKwlD9ZEnx
cE+1AQCJt4ymZymSgHgErs7d7bpQs6C8IBbvy/b/lhXw45RezgD/ani5owqPzQfE
+dWhOCrG8dFu8lrOB2JkHWpbyd6W4gg=
=iEf+
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-for-v5.14-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for the new RZ/G2L SoC
* tag 'renesas-clk-for-v5.14-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: Add support for R9A07G044 SoC
clk: renesas: Add CPG core wrapper for RZ/G2L SoC
dt-bindings: clock: renesas: Document RZ/G2L SoC CPG driver
dt-bindings: clock: Add r9a07g044 CPG Clock Definitions
Define the clock outputs supported by RZ/G2L (R9A07G044) SoC
and bind it with RZ/G2L CPG core.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Clock definitions for the Renesas RZ/G2L (R9A07G044) SoC, shared by
driver and DT source files.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYMIU6AAKCRCKwlD9ZEnx
cLTzAQDCHXUk8nXxbehYjdcDP7X3xEVh5OeZwSAKbwxKQvWtoQEAnlOysnT1LF0m
iNERFlisNuaR2hKXseifgf/7EIHRZQU=
=YzeJ
-----END PGP SIGNATURE-----
Merge tag 'renesas-r9a07g044-dt-binding-defs-tag' into renesas-clk-for-v5.14
Renesas RZ/G2L DT Binding Definitions
Clock definitions for the Renesas RZ/G2L (R9A07G044) SoC, shared by
driver and DT source files.
Add CPG core wrapper for RZ/G2L family.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-9-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document the device tree bindings of the Renesas RZ/G2L SoC clock
driver in Documentation/devicetree/bindings/clock/renesas,rzg2l-cpg.yaml.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210609153230.6967-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the omap2_dpll_round_rate routine attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
DT bindings for enabling and adjusting spread spectrum clocking have
been added.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210606202253.31649-3-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
During my big cleanup I managed to assign an AO clock to its
non-AO binding. Fix this.
Reported-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210606192657.51037-1-konrad.dybcio@somainline.org
Fixes: a0384ecfe2aa ("clk: qcom: smd-rpm: De-duplicate identical entries")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
kbuild robot reports that s390 fails to build this driver with
COMPILE_TEST. Let's depend on HAS_IOMEM so that s390 doesn't try to
build it.
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 419b3ab6987f ("clk: versatile: remove dependency on ARCH_*")
Link: https://lore.kernel.org/r/20210604192321.2594519-1-sboyd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the dt-binding for the RPM Clock Controller on the MSM8226 SoC.
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20210502122027.9351-4-bartosz.dudziak@snejp.pl
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The display clock controller in SC8180x is reused from SM8150, so add
the necessary compatible and wire up the driver to enable this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210511041719.591969-1-bjorn.andersson@linaro.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It makes negative sense to keep repeating the same definitions
over and over and over and over again, just with changed names..
De-duplicate to make for a drastically smaller file size. This makes the
object file size 55% smaller according to bloat-o-meter:
Total: Before=70713, After=31353, chg -55.66%
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210524225456.398817-2-konrad.dybcio@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Switch to parent_data and with that fix the longstanding issue where
if there wasn't a clock precisely named "xo_board", rpmcc would not play
along well. This started to show lately when "xo_board" was being changed to
"xo-board" so as to align with DTS naming spec.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210524225456.398817-1-konrad.dybcio@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix the following make W=1 warning:
drivers/clk/analogbits/wrpll-cln28hpc.c:227: warning: expecting prototype for wrpll_configure(). Prototype was for wrpll_configure_for_rate() instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210601114154.3163327-1-yangyingliang@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix function name in sifive-prci.c kernel-doc comment
to remove a warning.
drivers/clk/sifive/sifive-prci.c:573: warning: expecting prototype for
sifive_prci_init(). Prototype was for sifive_prci_probe() instead
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1621851730-32287-1-git-send-email-yang.lee@linux.alibaba.com
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It is now possible to build a modular kernel for vexpress by
not setting CONFIG_ARCH_VEXPRESS=y and instead setting =m on the
drivers that it normally implies. This is with the exception of
CLK_VEXPRESS_OSC which is currently hidden behind a dependency on
one of several ARCH_* variables. Remove that dependency so that
CLK_VEXPRESS_OSC may be enabled without it.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/I435a21e2e5f6187db54f4ef2079b60028ab2ea69
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210520161702.3746174-1-lee.jones@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The dev_err_probe() function prints an error message if the error
code is not -EPROBE_DEFER. If we know the error code in is -ENODEV
then there is no reason to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YJotlJBJ1CVAgvMT@mwanda
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
dev_err_probe() returns the error code passed as second parameter. Also if
the error code is -EPROBE_DEFER dev_err_probe() is silent, so there is no
need to check for this value before calling dev_err_probe().
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210427164522.2886825-1-uwe@kleine-koenig.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
R-Car D3 ZA2 clock is from PLL0D3 or S0,
and it can be controlled by ZA2CKCR.
It is needed for R-Car Sound, but is not used so far.
Using default settings is very enough at this point.
This patch adds it by DEF_FIXED().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmxclrmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Realtime Module Stop Control Register definitions (RMSTPCR(i)) are
incorrect for i >= 8 on R-Car Gen2 and Gen3.
As these are unused, and not planned to be used, just like the
corresponding Modem Module Stop Control Register definitions (MMSTPCR())
on R-Mobile APE6 (they are intended for the software running on the
Real-Time and Modem CPU cores), they can just be removed.
Reported-by: Hai Nguyen Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/2d8bc4d9806b419ebb06030d2f31b2ea1e59b1d6.1620119700.git.geert+renesas@glider.be
The root clock generators with MND divider has the capability to support
change in duty-cycle by updating the 'D'. Add the clock ops which would
check all the boundary conditions and enable setting the desired duty-cycle
as per the consumer.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1619334502-9880-2-git-send-email-tdas@codeaurora.org
[sboyd@kernel.org: Remove _val everywhere]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the divider clocks on RZ/N1 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
Note that range checking is not yet implemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7a384d02b85cdaac4a0e2b357582c8244b9a6f98.1617282116.git.geert+renesas@glider.be
Currently the .determine_rate() callback considers only the current
parent clock, limiting the range of achievable clock rates on DIV6
clocks with multiple parents, as found on SH/R-Mobile SoCs.
Extend the callback to consider all available parent clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/60e639692b462f99e0b6ab868c3675b3d97dbdb0.1617281699.git.geert+renesas@glider.be
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the DIV6 clocks on SH/R-Mobile and R-Car
SoCs from the old .round_rate() callback to the newer .determine_rate()
callback, which does not suffer from this limitation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7fd8c45cd8bf5c6d928ca69c8b669be35b93de09.1617281699.git.geert+renesas@glider.be
