[Why]
Fixes the following scenario:
- Flip has been prepared sometime during the frame, update pending
- Cursor update happens right when VUPDATE would happen
- OPTC lock acquired, VUPDATE is blocked until next frame
- Flip is delayed potentially infinitely
With the igt@kms_cursor_legacy cursor-vs-flip-legacy test we can
observe nearly *13* frames of delay for some flips on Navi.
[How]
Apply the Raven workaround generically. When close enough to VUPDATE
block cursor updates from occurring from the dc_stream_set_cursor_*
helpers.
This could perhaps be a little smarter by checking if there were
pending updates or flips earlier in the frame on the HUBP side before
applying the delay, but this should be fine for now.
This fixes the kms_cursor_legacy test.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently RN SOC bounding box update assumes we will get at least
2 clock states from SMU. This isn't always true and because of special
casing on first clock state we end up with low disp, dpp, dsc and phy
clocks.
This change removes the special casing allowing the first state to
acquire correct clocks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check before programming the register since it isn't present on
all IPs using this code.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A couple of regressions were found in rc1, as well as another set of races
and bugs :
- A regression where RDMA_CM_EVENT_REJECTED was lost in some cases
- Bad error handling in the CM, uverbs, rvt, siw and i40iw
- Kernel stack memory leak to user space in mlx4
- Missing data in a uapi query for mlx5
- Three races found by syzkaller in the ib core code
-----BEGIN PGP SIGNATURE-----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=/Hg3
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A couple of regressions were found in rc1, as well as another set of
races and bugs:
- A regression where RDMA_CM_EVENT_REJECTED was lost in some cases
- Bad error handling in the CM, uverbs, rvt, siw and i40iw
- Kernel stack memory leak to user space in mlx4
- Missing data in a uapi query for mlx5
- Three races found by syzkaller in the ib core code"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Fix race between destroy and release FD object
IB/rdmavt: Always return ERR_PTR from rvt_create_mmap_info()
RDMA/core: Fix overwriting of uobj in case of error
RDMA/core: Prevent mixed use of FDs between shared ufiles
RDMA/uverbs: Fix a race with disassociate and exit_mmap()
RDMA/mlx5: Set GRH fields in query QP on RoCE
RDMA/siw: Fix potential siw_mem refcnt leak in siw_fastreg_mr()
RDMA/mlx4: Initialize ib_spec on the stack
RDMA/cm: Fix an error check in cm_alloc_id_priv()
RDMA/cm: Fix missing RDMA_CM_EVENT_REJECTED event after receiving REJ message
i40iw: fix null pointer dereference on a null wqe pointer
Bugfixes:
- Restore wake-up-all to rpcrdma_cm_event_handler()
- Otherwise the client won't respond to server disconnect requests
- Fix tracepoint use-after-free race
- Fix usage of xdr_stream_encode_item_{present, absent}
- These functions return a size on success, and not 0
-----BEGIN PGP SIGNATURE-----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=jre3
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-5.7-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
NFSoRDMA Client Fixes for Linux 5.7
Bugfixes:
- Restore wake-up-all to rpcrdma_cm_event_handler()
- Otherwise the client won't respond to server disconnect requests
- Fix tracepoint use-after-free race
- Fix usage of xdr_stream_encode_item_{present, absent}
- These functions return a size on success, and not 0
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Currently, if the client sends BIND_CONN_TO_SESSION with
NFS4_CDFC4_FORE_OR_BOTH but only gets NFS4_CDFS4_FORE back it ignores
that it wasn't able to enable a backchannel.
To make sure, the client sends BIND_CONN_TO_SESSION as the first
operation on the connections (ie., no other session compounds haven't
been sent before), and if the client's request to bind the backchannel
is not satisfied, then reset the connection and retry.
Cc: stable@vger.kernel.org
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The rpciod workqueue is on the write-out path for freeing dirty memory,
so it is important that it never block waiting for memory to be
allocated - this can lead to a deadlock.
rpc_execute() - which is often called by an rpciod work item - calls
rcp_task_release_client() which can lead to rpc_free_client().
rpc_free_client() makes two calls which could potentially block wating
for memory allocation.
rpc_clnt_debugfs_unregister() calls into debugfs and will block while
any of the debugfs files are being accessed. In particular it can block
while any of the 'open' methods are being called and all of these use
malloc for one thing or another. So this can deadlock if the memory
allocation waits for NFS to complete some writes via rpciod.
rpc_clnt_remove_pipedir() can take the inode_lock() and while it isn't
obvious that memory allocations can happen while the lock it held, it is
safer to assume they might and to not let rpciod call
rpc_clnt_remove_pipedir().
So this patch moves these two calls (together with the final kfree() and
rpciod_down()) into a work-item to be run from the system work-queue.
rpciod can continue its important work, and the final stages of the free
can happen whenever they happen.
I have seen this deadlock on a 4.12 based kernel where debugfs used
synchronize_srcu() when removing objects. synchronize_srcu() requires a
workqueue and there were no free workther threads and none could be
allocated. While debugsfs no longer uses SRCU, I believe the deadlock
is still possible.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This fixes GPU hangs due to cache coherency issues.
Bump the driver version. Split out from the original patch.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes GPU hangs due to cache coherency issues.
v2: Split the version bump to a separate patch
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
DCC_INDEPENDENT_128B is needed for displayble DCC on gfx10.
SCANOUT is not needed by the kernel, but Mesa uses it.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
hwmgr->pm_en is initialized at hwmgr_hw_init.
during amdgpu_device_init, there is amdgpu_asic_reset that calls to
soc15_asic_reset (for V320 usecase, Vega10 asic), in which:
1) soc15_asic_reset_method calls to pp_get_asic_baco_capability (pm_en)
2) soc15_asic_baco_reset calls to pp_set_asic_baco_state (pm_en)
pm_en is used in the above two cases while it has not yet been initialized
So avoid using pm_en in the above two functions for V320 passthrough.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c5207876232649ca5e5ddd6f966d2da75ffded8f.
The commit being reverted changed the wrong place, it should have
changed in func get_asic_baco_capability.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we do
% echo 1 > /sys/module/dmatest/parameters/run
[ 115.851124] dmatest: Could not start test, no channels configured
% echo dma8chan7 > /sys/module/dmatest/parameters/channel
[ 127.563872] dmatest: Added 1 threads using dma8chan7
% cat /sys/module/dmatest/parameters/wait
... !!! HANG !!! ...
The culprit is the commit 6138f967bccc
("dmaengine: dmatest: Use fixed point div to calculate iops")
which makes threads not to run, but pending and being kicked off by writing
to the 'run' node. However, it forgot to consider 'wait' routine to avoid
above mentioned case.
In order to fix this, check for really running threads, i.e. with pending
and done flags unset.
It's pity the culprit commit hadn't updated documentation and tested all
possible scenarios.
Fixes: 6138f967bccc ("dmaengine: dmatest: Use fixed point div to calculate iops")
Cc: Seraj Alijan <seraj.alijan@sondrel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200428113518.70620-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This fixes CVE-2020-11884 which allows for a local kernel crash or
code execution.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=F1vM
-----END PGP SIGNATURE-----
Merge tag 'cve-2020-11884' from emailed bundle
Pull s390 fix from Christian Borntraeger:
"Fix a race between page table upgrade and uaccess on s390.
This fixes CVE-2020-11884 which allows for a local kernel crash or
code execution"
* tag 'cve-2020-11884' from emailed bundle:
s390/mm: fix page table upgrade vs 2ndary address mode accesses
A race exists between build_pcms() and build_controls() phases of codec
setup. Build_pcms() sets up notifier for jack events. If a monitor event
is received before build_controls() is run, the initial jack state is
lost and never reported via mixer controls.
The problem can be hit at least with SOF as the controller driver. SOF
calls snd_hda_codec_build_controls() in its workqueue-based probe and
this can be delayed enough to hit the race condition.
Fix the issue by invalidating the per-pin ELD information when
build_controls() is called. The existing call to hdmi_present_sense()
will update the ELD contents. This ensures initial monitor state is
correctly reflected via mixer controls.
BugLink: https://github.com/thesofproject/linux/issues/1687
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200428123836.24512-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When slave status is I2C_SLAVE_RX_END, generate I2C_SLAVE_STOP
event to i2c_client.
Fixes: c245d94ed106 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This can happen if userspace doesn't issue any 3D ioctls before
closing the DRM fd.
Fixes: 72b48ae800da ("drm/virtio: enqueue virtio_gpu_create_context after the first 3D ioctl")
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20200408232938.55816-1-gurchetansingh@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 60abd3181db2 ("selinux: convert cond_list to array")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
-----BEGIN PGP SIGNATURE-----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=Tbyq
-----END PGP SIGNATURE-----
Merge tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- regression fixes:
- transaction leak when deleting unused block group
- log cleanup after transaction abort
- fix block group leak when removing fails
- transaction leak if relocation recovery fails
- fix SPDX header
* tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix transaction leak in btrfs_recover_relocation
btrfs: fix block group leak when removing fails
btrfs: drop logs when we've aborted a transaction
btrfs: fix memory leak of transaction when deleting unused block group
btrfs: discard: Use the correct style for SPDX License Identifier
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl6mwOETHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXrFLB/4yKsrl41WwYRbTKgiir576/LA0vGxQ
cZjUQwkVv3S5/AfhvpwiGFV4dBV6j81KtNhRE6luaa3FBHObnjrx5tNqMw/P8a0j
HZGZ68n4qE+OPVtTxj54s81iWIi9vgT/La92GPYhuXoiVPTd5zJ2lwY3so04BSFJ
p30+RZFKNkTjNYZNZSHcoodr+js4Uws8JSn8OmpCJr8Gt+FJqkujQROG3HMKhJlk
KlJlCJhV48tj/nlgcbGHBF0Yy5l8DVCaKIz+MiF5F/i+P8r0cErfyihc9Ene0/un
LNFhIVGn8/MTi0CVrltcnur2qFH1qPCuLolKSpd/FKd6H2UDgK16XgAd
=NJP/
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fixes from Wei Liu:
- Two patches from Dexuan fixing suspension bugs
- Three cleanup patches from Andy and Michael
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hyper-v: Remove internal types from UAPI header
hyper-v: Use UUID API for exporting the GUID
x86/hyperv: Suspend/resume the VP assist page for hibernation
Drivers: hv: Move AEOI determination to architecture dependent code
Drivers: hv: vmbus: Fix Suspend-to-Idle for Generation-2 VM
drm_dp_mst_wait_tx_reply() returns > 1 if time elapsed in
wait_event_timeout() before check_txmsg_state(mgr, txmsg) evaluated to
true. However, we make the mistake of returning this time from
drm_dp_send_dpcd_write() on success instead of returning the number of
bytes written - causing spontaneous failures during link probing:
[drm:drm_dp_send_link_address [drm_kms_helper]] *ERROR* GUID check on
10:01 failed: 3975
Yikes! So, fix this by returning the number of bytes written on success
instead.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cb897542c6d2 ("drm/dp_mst: Fix W=1 warnings")
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424190722.775284-1-lyude@redhat.com
While the ggtt vma are protected by their object lifetime, the list
continues until it hits a non-ggtt vma, and that vma is not protected
and may be freed as we inspect it. Hence, we require the obj->vma.lock
to protect the list as we iterate.
An example of forgetting to hold the obj->vma.lock is
[1642834.464973] general protection fault, probably for non-canonical address 0xdead000000000122: 0000 [#1] SMP PTI
[1642834.464977] CPU: 3 PID: 1954 Comm: Xorg Not tainted 5.6.0-300.fc32.x86_64 #1
[1642834.464979] Hardware name: LENOVO 20ARS25701/20ARS25701, BIOS GJET94WW (2.44 ) 09/14/2017
[1642834.465021] RIP: 0010:i915_gem_object_set_tiling+0x2c0/0x3e0 [i915]
[1642834.465024] Code: 8b 84 24 18 01 00 00 f6 c4 80 74 59 49 8b 94 24 a0 00 00 00 49 8b 84 24 e0 00 00 00 49 8b 74 24 10 48 8b 92 30 01 00 00 89 c7 <80> ba 0a 06 00 00 03 0f 87 86 00 00 00 ba 00 00 08 00 b9 00 00 10
[1642834.465025] RSP: 0018:ffffa98780c77d60 EFLAGS: 00010282
[1642834.465028] RAX: ffff8d232bfb2578 RBX: 0000000000000002 RCX: ffff8d25873a0000
[1642834.465029] RDX: dead000000000122 RSI: fffff0af8ac6e408 RDI: 000000002bfb2578
[1642834.465030] RBP: ffff8d25873a0000 R08: ffff8d252bfb5638 R09: 0000000000000000
[1642834.465031] R10: 0000000000000000 R11: ffff8d252bfb5640 R12: ffffa987801cb8f8
[1642834.465032] R13: 0000000000001000 R14: ffff8d233e972e50 R15: ffff8d233e972d00
[1642834.465034] FS: 00007f6a3d327f00(0000) GS:ffff8d25926c0000(0000) knlGS:0000000000000000
[1642834.465036] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[1642834.465037] CR2: 00007f6a2064d000 CR3: 00000002fb57c001 CR4: 00000000001606e0
[1642834.465038] Call Trace:
[1642834.465083] i915_gem_set_tiling_ioctl+0x122/0x230 [i915]
[1642834.465121] ? i915_gem_object_set_tiling+0x3e0/0x3e0 [i915]
[1642834.465151] drm_ioctl_kernel+0x86/0xd0 [drm]
[1642834.465156] ? avc_has_perm+0x3b/0x160
[1642834.465178] drm_ioctl+0x206/0x390 [drm]
[1642834.465216] ? i915_gem_object_set_tiling+0x3e0/0x3e0 [i915]
[1642834.465221] ? selinux_file_ioctl+0x122/0x1c0
[1642834.465226] ? __do_munmap+0x24b/0x4d0
[1642834.465231] ksys_ioctl+0x82/0xc0
[1642834.465235] __x64_sys_ioctl+0x16/0x20
[1642834.465238] do_syscall_64+0x5b/0xf0
[1642834.465243] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[1642834.465245] RIP: 0033:0x7f6a3d7b047b
[1642834.465247] Code: 0f 1e fa 48 8b 05 1d aa 0c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ed a9 0c 00 f7 d8 64 89 01 48
[1642834.465249] RSP: 002b:00007ffe71adba28 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[1642834.465251] RAX: ffffffffffffffda RBX: 000055f99048fa40 RCX: 00007f6a3d7b047b
[1642834.465253] RDX: 00007ffe71adba30 RSI: 00000000c0106461 RDI: 000000000000000e
[1642834.465254] RBP: 0000000000000002 R08: 000055f98f3f1798 R09: 0000000000000002
[1642834.465255] R10: 0000000000001000 R11: 0000000000000246 R12: 0000000000000080
[1642834.465257] R13: 000055f98f3f1690 R14: 00000000c0106461 R15: 00007ffe71adba30
Now to take the spinlock during the list iteration, we need to break it
down into two phases. In the first phase under the lock, we cannot sleep
and so must defer the actual work to a second list, protected by the
ggtt->mutex.
We also need to hold the spinlock during creation of a new vma to
serialise with updates of the tiling on the object.
Reported-by: Dave Airlie <airlied@redhat.com>
Fixes: 2850748ef876 ("drm/i915: Pull i915_vma_pin under the vm->mutex")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422072805.17340-1-chris@chris-wilson.co.uk
(cherry picked from commit cb593e5d2b6d3ad489669914d9fd1c64c7a4a6af)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
igt_ppgtt_pin_update() invokes i915_gem_context_get_vm_rcu(), which
returns a reference of the i915_address_space object to "vm" with
increased refcount.
When igt_ppgtt_pin_update() returns, "vm" becomes invalid, so the
refcount should be decreased to keep refcount balanced.
The reference counting issue happens in two exception handling paths of
igt_ppgtt_pin_update(). When i915_gem_object_create_internal() returns
IS_ERR, the refcnt increased by i915_gem_context_get_vm_rcu() is not
decreased, causing a refcnt leak.
Fix this issue by jumping to "out_vm" label when
i915_gem_object_create_internal() returns IS_ERR.
Fixes: a4e7ccdac38e ("drm/i915: Move context management under GEM")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1587361342-83494-1-git-send-email-xiyuyang19@fudan.edu.cn
(cherry picked from commit e07c7606a00c4361bad72ff4e72ed0dfbefa23b0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Clay reports that OP_STATX fails for a test case with a valid fd
and empty path:
-- Test 0: statx:fd 3: SUCCEED, file mode 100755
-- Test 1: statx:path ./uring_statx: SUCCEED, file mode 100755
-- Test 2: io_uring_statx:fd 3: FAIL, errno 9: Bad file descriptor
-- Test 3: io_uring_statx:path ./uring_statx: SUCCEED, file mode 100755
This is due to statx not grabbing the process file table, hence we can't
lookup the fd in async context. If the fd is valid, ensure that we grab
the file table so we can grab the file from async context.
Cc: stable@vger.kernel.org # v5.6
Reported-by: Clay Harris <bugs@claycon.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Under some circumstances, i.e. when test is still running and about to
time out and user runs, for example,
grep -H . /sys/module/dmatest/parameters/*
the iterations parameter is not respected and test is going on and on until
user gives
echo 0 > /sys/module/dmatest/parameters/run
This is not what expected.
The history of this bug is interesting. I though that the commit
2d88ce76eb98 ("dmatest: add a 'wait' parameter")
is a culprit, but looking closer to the code I think it simple revealed the
broken logic from the day one, i.e. in the commit
0a2ff57d6fba ("dmaengine: dmatest: add a maximum number of test iterations")
which adds iterations parameter.
So, to the point, the conditional of checking the thread to be stopped being
first part of conjunction logic prevents to check iterations. Thus, we have to
always check both conditions to be able to stop after given iterations.
Since it wasn't visible before second commit appeared, I add a respective
Fixes tag.
Fixes: 2d88ce76eb98 ("dmatest: add a 'wait' parameter")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200424161147.16895-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DMA synchronization hook checks whether interrupt is raised by testing
corresponding bit in a hardware status register, and thus, clock should
be enabled in this case, otherwise CPU may hang if synchronization is
invoked while Runtime PM is in suspended state. This patch resumes the RPM
during of the DMA synchronization process in order to avoid potential
problems. It is a minor clean up of a previous commit, no real problem is
fixed by this patch because currently RPM is always in a resumed state
while DMA is synchronized, although this may change in the future.
Fixes: 6697255f239f ("dmaengine: tegra-apb: Improve DMA synchronization")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200426190835.21950-1-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the channel register code was changed to allow hotplug operations,
dynamic indexing wasn't taken into account. When channels are randomly
plugged and unplugged out of order, the serial indexing breaks. Convert
channel indexing to using IDA tracking in order to allow dynamic
assignment. The previous code does not cause any regression bug for
existing channel allocation besides idxd driver since the hotplug usage
case is only used by idxd at this point.
With this change, the chan->idr_ref is also not needed any longer. We can
have a device with no channels registered due to hot plug. The channel
device release code no longer should attempt to free the dma device id on
the last channel release.
Fixes: e81274cd6b52 ("dmaengine: add support to dynamic register/unregister of channels")
Reported-by: Yixin Zhang <yixin.zhang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Yixin Zhang <yixin.zhang@intel.com>
Link: https://lore.kernel.org/r/158679961260.7674.8485924270472851852.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[BUG]
One run of btrfs/063 triggered the following lockdep warning:
============================================
WARNING: possible recursive locking detected
5.6.0-rc7-custom+ #48 Not tainted
--------------------------------------------
kworker/u24:0/7 is trying to acquire lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
but task is already holding lock:
ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(sb_internal#2);
lock(sb_internal#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u24:0/7:
#0: ffff88817b495948 ((wq_completion)btrfs-endio-write){+.+.}, at: process_one_work+0x557/0xb80
#1: ffff888189ea7db8 ((work_completion)(&work->normal_work)){+.+.}, at: process_one_work+0x557/0xb80
#2: ffff88817d3a46e0 (sb_internal#2){.+.+}, at: start_transaction+0x66c/0x890 [btrfs]
#3: ffff888174ca4da8 (&fs_info->reloc_mutex){+.+.}, at: btrfs_record_root_in_trans+0x83/0xd0 [btrfs]
stack backtrace:
CPU: 0 PID: 7 Comm: kworker/u24:0 Not tainted 5.6.0-rc7-custom+ #48
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
Call Trace:
dump_stack+0xc2/0x11a
__lock_acquire.cold+0xce/0x214
lock_acquire+0xe6/0x210
__sb_start_write+0x14e/0x290
start_transaction+0x66c/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
find_free_extent+0x1504/0x1a50 [btrfs]
btrfs_reserve_extent+0xd5/0x1f0 [btrfs]
btrfs_alloc_tree_block+0x1ac/0x570 [btrfs]
btrfs_copy_root+0x213/0x580 [btrfs]
create_reloc_root+0x3bd/0x470 [btrfs]
btrfs_init_reloc_root+0x2d2/0x310 [btrfs]
record_root_in_trans+0x191/0x1d0 [btrfs]
btrfs_record_root_in_trans+0x90/0xd0 [btrfs]
start_transaction+0x16e/0x890 [btrfs]
btrfs_join_transaction+0x1d/0x20 [btrfs]
btrfs_finish_ordered_io+0x55d/0xcd0 [btrfs]
finish_ordered_fn+0x15/0x20 [btrfs]
btrfs_work_helper+0x116/0x9a0 [btrfs]
process_one_work+0x632/0xb80
worker_thread+0x80/0x690
kthread+0x1a3/0x1f0
ret_from_fork+0x27/0x50
It's pretty hard to reproduce, only one hit so far.
[CAUSE]
This is because we're calling btrfs_join_transaction() without re-using
the current running one:
btrfs_finish_ordered_io()
|- btrfs_join_transaction() <<< Call #1
|- btrfs_record_root_in_trans()
|- btrfs_reserve_extent()
|- btrfs_join_transaction() <<< Call #2
Normally such btrfs_join_transaction() call should re-use the existing
one, without trying to re-start a transaction.
But the problem is, in btrfs_join_transaction() call #1, we call
btrfs_record_root_in_trans() before initializing current::journal_info.
And in btrfs_join_transaction() call #2, we're relying on
current::journal_info to avoid such deadlock.
[FIX]
Call btrfs_record_root_in_trans() after we have initialized
current::journal_info.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we have an inode with a prealloc extent that starts at an offset
lower than the i_size and there is another prealloc extent that starts at
an offset beyond i_size, we can end up losing part of the first prealloc
extent (the part that starts at i_size) and have an implicit hole if we
fsync the file and then have a power failure.
Consider the following example with comments explaining how and why it
happens.
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
# Create our test file with 2 consecutive prealloc extents, each with a
# size of 128Kb, and covering the range from 0 to 256Kb, with a file
# size of 0.
$ xfs_io -f -c "falloc -k 0 128K" /mnt/foo
$ xfs_io -c "falloc -k 128K 128K" /mnt/foo
# Fsync the file to record both extents in the log tree.
$ xfs_io -c "fsync" /mnt/foo
# Now do a redudant extent allocation for the range from 0 to 64Kb.
# This will merely increase the file size from 0 to 64Kb. Instead we
# could also do a truncate to set the file size to 64Kb.
$ xfs_io -c "falloc 0 64K" /mnt/foo
# Fsync the file, so we update the inode item in the log tree with the
# new file size (64Kb). This also ends up setting the number of bytes
# for the first prealloc extent to 64Kb. This is done by the truncation
# at btrfs_log_prealloc_extents().
# This means that if a power failure happens after this, a write into
# the file range 64Kb to 128Kb will not use the prealloc extent and
# will result in allocation of a new extent.
$ xfs_io -c "fsync" /mnt/foo
# Now set the file size to 256K with a truncate and then fsync the file.
# Since no changes happened to the extents, the fsync only updates the
# i_size in the inode item at the log tree. This results in an implicit
# hole for the file range from 64Kb to 128Kb, something which fsck will
# complain when not using the NO_HOLES feature if we replay the log
# after a power failure.
$ xfs_io -c "truncate 256K" -c "fsync" /mnt/foo
So instead of always truncating the log to the inode's current i_size at
btrfs_log_prealloc_extents(), check first if there's a prealloc extent
that starts at an offset lower than the i_size and with a length that
crosses the i_size - if there is one, just make sure we truncate to a
size that corresponds to the end offset of that prealloc extent, so
that we don't lose the part of that extent that starts at i_size if a
power failure happens.
A test case for fstests follows soon.
Fixes: 31d11b83b96f ("Btrfs: fix duplicate extents after fsync of file with prealloc extents")
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When jumping to the out_put_disk label, we will call put_disk(), which will
trigger a call to disk_release(), which calls blk_put_queue().
Later in the cleanup code, we do blk_cleanup_queue(), which will also call
blk_put_queue().
Putting the queue twice is incorrect, and will generate a KASAN splat.
Set the disk->queue pointer to NULL, before calling put_disk(), so that the
first call to blk_put_queue() will not free the queue.
The second call to blk_put_queue() uses another pointer to the same queue,
so this call will still free the queue.
Fixes: 85136c010285 ("lightnvm: simplify geometry enumeration")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
... to protect the modification of mp->m_count done by it. Most of
the places that modify that thing also have namespace_lock held,
but not all of them can do so, so we really need mount_lock here.
Kudos to Piotr Krysiuk <piotras@gmail.com>, who'd spotted a related
bug in pivot_root(2) (fixed unnoticed in 5.3); search for other
similar turds has caught out this one.
Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Transitioned power state logged at the end of setting ACPI power.
However, D3cold won't be in the message because state can only be
D3hot at most.
Use target_state to corretly report when power state is D3cold.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the kernel threads are not frozen in software_resume(), so
between dpm_suspend_start(PMSG_QUIESCE) and resume_target_kernel(),
system_freezable_power_efficient_wq can still try to submit SCSI
commands and this can cause a panic since the low level SCSI driver
(e.g. hv_storvsc) has quiesced the SCSI adapter and can not accept
any SCSI commands: https://lkml.org/lkml/2020/4/10/47
At first I posted a fix (https://lkml.org/lkml/2020/4/21/1318) trying
to resolve the issue from hv_storvsc, but with the help of
Bart Van Assche, I realized it's better to fix software_resume(),
since this looks like a generic issue, not only pertaining to SCSI.
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make a note of the first time we discover the turbo mode has been
disabled by the BIOS, as otherwise we complain every time we try to
update the mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This new Lenovo ThinkCenter has two front mics which can't be handled
by PA so far, so apply the fixup ALC283_FIXUP_HEADSET_MIC to change
the location for one of the mics.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200427030039.10121-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=x+F1
-----END PGP SIGNATURE-----
Merge tag '5.7-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five cifs/smb3 fixes:two for DFS reconnect failover, one lease fix for
stable and the others to fix a missing spinlock during reconnect"
* tag '5.7-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix uninitialised lease_key in open_shroot()
cifs: ensure correct super block for DFS reconnect
cifs: do not share tcons with DFS
cifs: minor update to comments around the cifs_tcp_ses_lock mutex
cifs: protect updating server->dstaddr with a spinlock
Here are a number of USB driver fixes for 5.7-rc3.
Nothing huge, just the usual collection of:
- xhci fixes
- gadget driver fixes
- syzkaller fuzzing fixes
- new device ids and DT bindings
- new quirks added for broken devices
A few of the gadget driver fixes show up twice here as they were applied
to my branch, and also by Felipe to his branch which I then pulled in as
we got out of sync a bit.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXqVfog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynVFwCfb33URz0KrXE+ipecpheVEoMdvDsAoIuYG4cb
qxLwEE6203jdICq9/nDg
=8f/s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB driver fixes for 5.7-rc3.
Nothing huge, just the usual collection of:
- xhci fixes
- gadget driver fixes
- syzkaller fuzzing fixes
- new device ids and DT bindings
- new quirks added for broken devices
A few of the gadget driver fixes show up twice here as they were
applied to my branch, and also by Felipe to his branch which I then
pulled in as we got out of sync a bit.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
USB: sisusbvga: Change port variable from signed to unsigned
usb-storage: Add unusual_devs entry for JMicron JMS566
USB: hub: Revert commit bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices")
USB: hub: Fix handling of connect changes during sleep
usb: typec: altmode: Fix typec_altmode_get_partner sometimes returning an invalid pointer
xhci: Don't clear hub TT buffer on ep0 protocol stall
xhci: prevent bus suspend if a roothub port detected a over-current condition
xhci: Fix handling halted endpoint even if endpoint ring appears empty
usb: raw-gadget: Fix copy_to/from_user() checks
usb: raw-gadget: fix raw_event_queue_fetch locking
usb: gadget: udc: atmel: Fix vbus disconnect handling
usb: dwc3: gadget: Fix request completion check
USB: Add USB_QUIRK_DELAY_CTRL_MSG and USB_QUIRK_DELAY_INIT for Corsair K70 RGB RAPIDFIRE
phy: tegra: Select USB_COMMON for usb_get_maximum_speed()
usb: typec: tcpm: Ignore CC and vbus changes in PORT_RESET change
usb: f_fs: Clear OS Extended descriptor counts to zero in ffs_data_reset()
cdc-acm: introduce a cool down
cdc-acm: close race betrween suspend() and acm_softint
UAS: fix deadlock in error handling and PM flushing work
UAS: no use logging any details in case of ENODEV
...
Here are some tty and serial driver fixes for 5.7-rc3.
The "largest" in here are a number of reverts for previous changes to
the uartps serial driver that turned out to not be a good idea at all.
The others are just small fixes found by people and tools. Included in
here is a much-reported symbol export needed by previous changes that
happened in 5.7-rc1. All of these have been in linux-next for a while
with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXqVgiQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynvFgCfR5YTJnCrJUbPqGAuguZYlSGzNzUAoMTc4W9A
H4nsF9NweTl+FHFQq4J+
=xWz2
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 5.7-rc3.
The "largest" in here are a number of reverts for previous changes to
the uartps serial driver that turned out to not be a good idea at all.
The others are just small fixes found by people and tools. Included in
here is a much-reported symbol export needed by previous changes that
happened in 5.7-rc1. All of these have been in linux-next for a while
with no reported issues"
* tag 'tty-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: hvc: fix buffer overflow during hvc_alloc().
tty: rocket, avoid OOB access
tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart
vt: don't hardcode the mem allocation upper bound
tty: serial: owl: add "much needed" clk_prepare_enable()
vt: don't use kmalloc() for the unicode screen buffer
tty/sysrq: Export sysrq_mask(), sysrq_toggle_support()
serial: sh-sci: Make sure status register SCxSR is read in correct sequence
serial: sunhv: Initialize lock for non-registered console
Revert "serial: uartps: Register own uart console and driver structures"
Revert "serial: uartps: Move Port ID to device data structure"
Revert "serial: uartps: Change uart ID port allocation"
Revert "serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES"
Revert "serial: uartps: Fix error path when alloc failed"
Revert "serial: uartps: Use the same dynamic major number for all ports"
Revert "serial: uartps: Fix uartps_major handling"
Here are 4 small misc driver fixes for 5.7-rc3:
- mei driver fix
- interconnect driver fix
- 2 fpga driver fixes
All have been in linux-next with no reported issue
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXqVmbw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynYSACghD2iG6TQyaKnNOUZWwssrTJxWs8AoIxC5q3m
UerIRQ2QQRO6ZqdsnizG
=TUCP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are 4 small misc driver fixes for 5.7-rc3:
- mei driver fix
- interconnect driver fix
- two fpga driver fixes
All have been in linux-next with no reported issues"
* tag 'char-misc-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
interconnect: qcom: Fix uninitialized tcs_cmd::wait
mei: me: fix irq number stored in hw struct
fpga: dfl: pci: fix return value of cci_pci_sriov_configure
fpga: zynq: Remove clk_get error message for probe defer
Here are some small staging and IIO driver fixes for 5.7-rc3
Lots of tiny things for reported issues in staging and IIO drivers,
including a counter driver fix as well (the iio drivers seem to be tied
to those). Full details of the fixes are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXqVi+g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLVACeMUPjrHp/NiueD8hcN9F2iXRN3D8AoI6fU5bL
DsFiYs8n1TaZdEd7nbl0
=7wq7
-----END PGP SIGNATURE-----
Merge tag 'staging-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are some small staging and IIO driver fixes for 5.7-rc3
Lots of tiny things for reported issues in staging and IIO drivers,
including a counter driver fix as well (the iio drivers seem to be
tied to those). Full details of the fixes are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (27 commits)
staging: vt6656: Fix calling conditions of vnt_set_bss_mode
staging: comedi: Fix comedi_device refcnt leak in comedi_open
staging: vt6656: Fix pairwise key entry save.
staging: vt6656: Fix drivers TBTT timing counter.
staging: vt6656: Don't set RCR_MULTICAST or RCR_BROADCAST by default.
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
...
Here are some small firmware/driver core/debugfs fixes for 5.7-rc3.
The debugfs change is now possible as now the last users of
debugfs_create_u32() have been fixed up in the different trees that got
merged into 5.7-rc1, and I don't want it creeping back in.
The firmware changes did cause a regression in linux-next, so the final
patch here reverts part of that, re-exporting the symbol to resolve that
issue. All of these patches, with the exception of the final one, have
been in linux-next with only that one reported issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXqVliw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymf6ACfS5HoPt+kWKtfKteN/mt6WUeJz6oAoMDg4Qvf
4ncqmH9jt0lj5NAwHxFi
=DP2q
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small firmware/driver core/debugfs fixes for 5.7-rc3.
The debugfs change is now possible as now the last users of
debugfs_create_u32() have been fixed up in the different trees that
got merged into 5.7-rc1, and I don't want it creeping back in.
The firmware changes did cause a regression in linux-next, so the
final patch here reverts part of that, re-exporting the symbol to
resolve that issue. All of these patches, with the exception of the
final one, have been in linux-next with only that one reported issue"
* tag 'driver-core-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware_loader: revert removal of the fw_fallback_config export
debugfs: remove return value of debugfs_create_u32()
firmware_loader: remove unused exports
firmware: imx: fix compile-testing
- Add few notrace annotations to avoid potential crashes when switching
ftrace tracers.
- Avoid setting affinity for floating irqs in pci code.
- Fix build issue found by kbuild test robot.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6lOMoACgkQjYWKoQLX
FBjQFQf/cA+F2tvEC+0YetUmwSaR+iPsCsgtCCSlBq5E8cCkzCf9uHVsXkmC647O
6vMsbFh7TeGmLbYPtgl/mFRjsuoVgD/Gm5TMm2nsWqZ3+C7pd8cMXCLY7dAtFb5d
judNcL0LSeBpytUflMLd2nXjuD90Y4dNd7J3WNC2l5/fdUW+Bd+97B+zj385wrTs
Z4Ab4KBzv+79e+4iMtn7xiK+RMnhP/pDij1RbtAI1XS33cigjSkZQb5gC/Yxb4Qy
badzecGOmdpod8A76didEeTTQ50bknT47dASwhguuDhdBZj36+SEnUXL0tiT1TFW
/Za3Q+rLFOe8OEqTsCBzEF55ijkXZQ==
=CBXL
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Add a few notrace annotations to avoid potential crashes when
switching ftrace tracers.
- Avoid setting affinity for floating irqs in pci code.
- Fix build issue found by kbuild test robot.
* tag 's390-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/protvirt: fix compilation issue
s390/pci: do not set affinity for floating irqs
s390/ftrace: fix potential crashes when switching tracers
- One important fix for a bug in the way we find the cache-line size from the
device tree, which was leading to the wrong size being reported to userspace
on some platforms.
- A fix for 8xx STRICT_KERNEL_RWX which was leaving TLB entries around leading
to a window at boot when the strict mapping wasn't enforced.
- A fix to enable our KUAP (kernel user access prevention) debugging on PPC32.
- A build fix for clang in lib/mpi.
Thanks to:
Chris Packham, Christophe Leroy, Nathan Chancellor, Qian Cai.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAl6kx1ITHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgNaFD/90YTMbKzERwayHDvdTu2oGrrCHoH59
mG013ByHuad24yOtRzuHUam3hvKrkxf1/aFjhTVTuuD6i3HGbDEHxo60qZm9t6ES
rtJ2stLa3p2JHRtYEtXbnV/TDGuXBcN9aVTZRJxakRSBDEBb5zQc+qu/RXtIYhPX
T8thmTaXq+v/YLXF2b0O/fIiCxIUEINBr1iafPL9Bh1LKX1lcOCq3xI4GBQoEGin
2w2hilAEKzCwSVIPVG0p1+73W6RUTUxnhSx/tUs0Zdzi6KTO9QSbLpsFq98qXFBm
Snd7b1oGj6vsc9xy5vNhmiFHRABOJOzewrjDJjI5BCeRi2SRUColD3NOCsVj1rCZ
IPJj5iojBYSnvzQRj13+a9DEH2kQNEf56MbPfxjpucZbCoxWfMgXBLxloC5AIHA6
1BipdEg1tM5FAOuhcnOOr/Mw83f73evsWVUFvyzah1D92m/VKux1IwXrwc394mtK
awUzKL380mbaKJCY3S/mD4nVLjkUIhnYRtNPr1QKsKF2KGC4VRcr2Y8rk1Dh0VgJ
KLv6kl8kCvCNIHdmpA3ycCxoFHEdc8qVZSKktIWucMjP7hDOFdrLiWQ6DgbqiPp5
hsPxAkgGac1xTH2l1TjRdgyqbSBglWvWcc3fvnjoB/3+BLE6T7CDPqTZqqYaCkKK
cvOqdMsoMXEFYA==
=pjVW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- One important fix for a bug in the way we find the cache-line size
from the device tree, which was leading to the wrong size being
reported to userspace on some platforms.
- A fix for 8xx STRICT_KERNEL_RWX which was leaving TLB entries around
leading to a window at boot when the strict mapping wasn't enforced.
- A fix to enable our KUAP (kernel user access prevention) debugging on
PPC32.
- A build fix for clang in lib/mpi.
Thanks to: Chris Packham, Christophe Leroy, Nathan Chancellor, Qian Cai.
* tag 'powerpc-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
lib/mpi: Fix building for powerpc with clang
powerpc/mm: Fix CONFIG_PPC_KUAP_DEBUG on PPC32
powerpc/8xx: Fix STRICT_KERNEL_RWX startup test failure
powerpc/setup_64: Set cache-line-size based on cache-block-size
