mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
synced 2024-12-29 09:13:38 +00:00
f755261190
The PM8937 provides 4 MPPs. Add a compatible to support them. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> Link: https://lore.kernel.org/20241031-msm8917-v2-4-8a075faa89b1@mainlining.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1013 lines
26 KiB
C
1013 lines
26 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
|
|
*/
|
|
|
|
#include <linux/gpio/driver.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_irq.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/seq_file.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/types.h>
|
|
|
|
#include <linux/pinctrl/pinconf-generic.h>
|
|
#include <linux/pinctrl/pinconf.h>
|
|
#include <linux/pinctrl/pinmux.h>
|
|
|
|
#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
|
|
|
|
#include "../core.h"
|
|
#include "../pinctrl-utils.h"
|
|
|
|
#define PMIC_MPP_ADDRESS_RANGE 0x100
|
|
|
|
/*
|
|
* Pull Up Values - it indicates whether a pull-up should be
|
|
* applied for bidirectional mode only. The hardware ignores the
|
|
* configuration when operating in other modes.
|
|
*/
|
|
#define PMIC_MPP_PULL_UP_0P6KOHM 0
|
|
#define PMIC_MPP_PULL_UP_10KOHM 1
|
|
#define PMIC_MPP_PULL_UP_30KOHM 2
|
|
#define PMIC_MPP_PULL_UP_OPEN 3
|
|
|
|
/* type registers base address bases */
|
|
#define PMIC_MPP_REG_TYPE 0x4
|
|
#define PMIC_MPP_REG_SUBTYPE 0x5
|
|
|
|
/* mpp peripheral type and subtype values */
|
|
#define PMIC_MPP_TYPE 0x11
|
|
#define PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT 0x3
|
|
#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT 0x4
|
|
#define PMIC_MPP_SUBTYPE_4CH_NO_SINK 0x5
|
|
#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK 0x6
|
|
#define PMIC_MPP_SUBTYPE_4CH_FULL_FUNC 0x7
|
|
#define PMIC_MPP_SUBTYPE_8CH_FULL_FUNC 0xf
|
|
|
|
#define PMIC_MPP_REG_RT_STS 0x10
|
|
#define PMIC_MPP_REG_RT_STS_VAL_MASK 0x1
|
|
|
|
/* control register base address bases */
|
|
#define PMIC_MPP_REG_MODE_CTL 0x40
|
|
#define PMIC_MPP_REG_DIG_VIN_CTL 0x41
|
|
#define PMIC_MPP_REG_DIG_PULL_CTL 0x42
|
|
#define PMIC_MPP_REG_DIG_IN_CTL 0x43
|
|
#define PMIC_MPP_REG_EN_CTL 0x46
|
|
#define PMIC_MPP_REG_AOUT_CTL 0x48
|
|
#define PMIC_MPP_REG_AIN_CTL 0x4a
|
|
#define PMIC_MPP_REG_SINK_CTL 0x4c
|
|
|
|
/* PMIC_MPP_REG_MODE_CTL */
|
|
#define PMIC_MPP_REG_MODE_VALUE_MASK 0x1
|
|
#define PMIC_MPP_REG_MODE_FUNCTION_SHIFT 1
|
|
#define PMIC_MPP_REG_MODE_FUNCTION_MASK 0x7
|
|
#define PMIC_MPP_REG_MODE_DIR_SHIFT 4
|
|
#define PMIC_MPP_REG_MODE_DIR_MASK 0x7
|
|
|
|
/* PMIC_MPP_REG_DIG_VIN_CTL */
|
|
#define PMIC_MPP_REG_VIN_SHIFT 0
|
|
#define PMIC_MPP_REG_VIN_MASK 0x7
|
|
|
|
/* PMIC_MPP_REG_DIG_PULL_CTL */
|
|
#define PMIC_MPP_REG_PULL_SHIFT 0
|
|
#define PMIC_MPP_REG_PULL_MASK 0x7
|
|
|
|
/* PMIC_MPP_REG_EN_CTL */
|
|
#define PMIC_MPP_REG_MASTER_EN_SHIFT 7
|
|
|
|
/* PMIC_MPP_REG_AIN_CTL */
|
|
#define PMIC_MPP_REG_AIN_ROUTE_SHIFT 0
|
|
#define PMIC_MPP_REG_AIN_ROUTE_MASK 0x7
|
|
|
|
#define PMIC_MPP_MODE_DIGITAL_INPUT 0
|
|
#define PMIC_MPP_MODE_DIGITAL_OUTPUT 1
|
|
#define PMIC_MPP_MODE_DIGITAL_BIDIR 2
|
|
#define PMIC_MPP_MODE_ANALOG_BIDIR 3
|
|
#define PMIC_MPP_MODE_ANALOG_INPUT 4
|
|
#define PMIC_MPP_MODE_ANALOG_OUTPUT 5
|
|
#define PMIC_MPP_MODE_CURRENT_SINK 6
|
|
|
|
#define PMIC_MPP_SELECTOR_NORMAL 0
|
|
#define PMIC_MPP_SELECTOR_PAIRED 1
|
|
#define PMIC_MPP_SELECTOR_DTEST_FIRST 4
|
|
|
|
#define PMIC_MPP_PHYSICAL_OFFSET 1
|
|
|
|
/* Qualcomm specific pin configurations */
|
|
#define PMIC_MPP_CONF_AMUX_ROUTE (PIN_CONFIG_END + 1)
|
|
#define PMIC_MPP_CONF_ANALOG_LEVEL (PIN_CONFIG_END + 2)
|
|
#define PMIC_MPP_CONF_DTEST_SELECTOR (PIN_CONFIG_END + 3)
|
|
#define PMIC_MPP_CONF_PAIRED (PIN_CONFIG_END + 4)
|
|
|
|
/**
|
|
* struct pmic_mpp_pad - keep current MPP settings
|
|
* @base: Address base in SPMI device.
|
|
* @is_enabled: Set to false when MPP should be put in high Z state.
|
|
* @out_value: Cached pin output value.
|
|
* @output_enabled: Set to true if MPP output logic is enabled.
|
|
* @input_enabled: Set to true if MPP input buffer logic is enabled.
|
|
* @paired: Pin operates in paired mode
|
|
* @has_pullup: Pin has support to configure pullup
|
|
* @num_sources: Number of power-sources supported by this MPP.
|
|
* @power_source: Current power-source used.
|
|
* @amux_input: Set the source for analog input.
|
|
* @aout_level: Analog output level
|
|
* @pullup: Pullup resistor value. Valid in Bidirectional mode only.
|
|
* @function: See pmic_mpp_functions[].
|
|
* @drive_strength: Amount of current in sink mode
|
|
* @dtest: DTEST route selector
|
|
*/
|
|
struct pmic_mpp_pad {
|
|
u16 base;
|
|
bool is_enabled;
|
|
bool out_value;
|
|
bool output_enabled;
|
|
bool input_enabled;
|
|
bool paired;
|
|
bool has_pullup;
|
|
unsigned int num_sources;
|
|
unsigned int power_source;
|
|
unsigned int amux_input;
|
|
unsigned int aout_level;
|
|
unsigned int pullup;
|
|
unsigned int function;
|
|
unsigned int drive_strength;
|
|
unsigned int dtest;
|
|
};
|
|
|
|
struct pmic_mpp_state {
|
|
struct device *dev;
|
|
struct regmap *map;
|
|
struct pinctrl_dev *ctrl;
|
|
struct gpio_chip chip;
|
|
};
|
|
|
|
static const struct pinconf_generic_params pmic_mpp_bindings[] = {
|
|
{"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE, 0},
|
|
{"qcom,analog-level", PMIC_MPP_CONF_ANALOG_LEVEL, 0},
|
|
{"qcom,dtest", PMIC_MPP_CONF_DTEST_SELECTOR, 0},
|
|
{"qcom,paired", PMIC_MPP_CONF_PAIRED, 0},
|
|
};
|
|
|
|
#ifdef CONFIG_DEBUG_FS
|
|
static const struct pin_config_item pmic_conf_items[] = {
|
|
PCONFDUMP(PMIC_MPP_CONF_AMUX_ROUTE, "analog mux", NULL, true),
|
|
PCONFDUMP(PMIC_MPP_CONF_ANALOG_LEVEL, "analog level", NULL, true),
|
|
PCONFDUMP(PMIC_MPP_CONF_DTEST_SELECTOR, "dtest", NULL, true),
|
|
PCONFDUMP(PMIC_MPP_CONF_PAIRED, "paired", NULL, false),
|
|
};
|
|
#endif
|
|
|
|
static const char *const pmic_mpp_groups[] = {
|
|
"mpp1", "mpp2", "mpp3", "mpp4", "mpp5", "mpp6", "mpp7", "mpp8",
|
|
};
|
|
|
|
#define PMIC_MPP_DIGITAL 0
|
|
#define PMIC_MPP_ANALOG 1
|
|
#define PMIC_MPP_SINK 2
|
|
|
|
static const char *const pmic_mpp_functions[] = {
|
|
"digital", "analog", "sink"
|
|
};
|
|
|
|
static int pmic_mpp_read(struct pmic_mpp_state *state,
|
|
struct pmic_mpp_pad *pad, unsigned int addr)
|
|
{
|
|
unsigned int val;
|
|
int ret;
|
|
|
|
ret = regmap_read(state->map, pad->base + addr, &val);
|
|
if (ret < 0)
|
|
dev_err(state->dev, "read 0x%x failed\n", addr);
|
|
else
|
|
ret = val;
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int pmic_mpp_write(struct pmic_mpp_state *state,
|
|
struct pmic_mpp_pad *pad, unsigned int addr,
|
|
unsigned int val)
|
|
{
|
|
int ret;
|
|
|
|
ret = regmap_write(state->map, pad->base + addr, val);
|
|
if (ret < 0)
|
|
dev_err(state->dev, "write 0x%x failed\n", addr);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int pmic_mpp_get_groups_count(struct pinctrl_dev *pctldev)
|
|
{
|
|
/* Every PIN is a group */
|
|
return pctldev->desc->npins;
|
|
}
|
|
|
|
static const char *pmic_mpp_get_group_name(struct pinctrl_dev *pctldev,
|
|
unsigned pin)
|
|
{
|
|
return pctldev->desc->pins[pin].name;
|
|
}
|
|
|
|
static int pmic_mpp_get_group_pins(struct pinctrl_dev *pctldev,
|
|
unsigned pin,
|
|
const unsigned **pins, unsigned *num_pins)
|
|
{
|
|
*pins = &pctldev->desc->pins[pin].number;
|
|
*num_pins = 1;
|
|
return 0;
|
|
}
|
|
|
|
static const struct pinctrl_ops pmic_mpp_pinctrl_ops = {
|
|
.get_groups_count = pmic_mpp_get_groups_count,
|
|
.get_group_name = pmic_mpp_get_group_name,
|
|
.get_group_pins = pmic_mpp_get_group_pins,
|
|
.dt_node_to_map = pinconf_generic_dt_node_to_map_group,
|
|
.dt_free_map = pinctrl_utils_free_map,
|
|
};
|
|
|
|
static int pmic_mpp_get_functions_count(struct pinctrl_dev *pctldev)
|
|
{
|
|
return ARRAY_SIZE(pmic_mpp_functions);
|
|
}
|
|
|
|
static const char *pmic_mpp_get_function_name(struct pinctrl_dev *pctldev,
|
|
unsigned function)
|
|
{
|
|
return pmic_mpp_functions[function];
|
|
}
|
|
|
|
static int pmic_mpp_get_function_groups(struct pinctrl_dev *pctldev,
|
|
unsigned function,
|
|
const char *const **groups,
|
|
unsigned *const num_qgroups)
|
|
{
|
|
*groups = pmic_mpp_groups;
|
|
*num_qgroups = pctldev->desc->npins;
|
|
return 0;
|
|
}
|
|
|
|
static int pmic_mpp_write_mode_ctl(struct pmic_mpp_state *state,
|
|
struct pmic_mpp_pad *pad)
|
|
{
|
|
unsigned int mode;
|
|
unsigned int sel;
|
|
unsigned int val;
|
|
unsigned int en;
|
|
|
|
switch (pad->function) {
|
|
case PMIC_MPP_ANALOG:
|
|
if (pad->input_enabled && pad->output_enabled)
|
|
mode = PMIC_MPP_MODE_ANALOG_BIDIR;
|
|
else if (pad->input_enabled)
|
|
mode = PMIC_MPP_MODE_ANALOG_INPUT;
|
|
else
|
|
mode = PMIC_MPP_MODE_ANALOG_OUTPUT;
|
|
break;
|
|
case PMIC_MPP_DIGITAL:
|
|
if (pad->input_enabled && pad->output_enabled)
|
|
mode = PMIC_MPP_MODE_DIGITAL_BIDIR;
|
|
else if (pad->input_enabled)
|
|
mode = PMIC_MPP_MODE_DIGITAL_INPUT;
|
|
else
|
|
mode = PMIC_MPP_MODE_DIGITAL_OUTPUT;
|
|
break;
|
|
case PMIC_MPP_SINK:
|
|
default:
|
|
mode = PMIC_MPP_MODE_CURRENT_SINK;
|
|
break;
|
|
}
|
|
|
|
if (pad->dtest)
|
|
sel = PMIC_MPP_SELECTOR_DTEST_FIRST + pad->dtest - 1;
|
|
else if (pad->paired)
|
|
sel = PMIC_MPP_SELECTOR_PAIRED;
|
|
else
|
|
sel = PMIC_MPP_SELECTOR_NORMAL;
|
|
|
|
en = !!pad->out_value;
|
|
|
|
val = mode << PMIC_MPP_REG_MODE_DIR_SHIFT |
|
|
sel << PMIC_MPP_REG_MODE_FUNCTION_SHIFT |
|
|
en;
|
|
|
|
return pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
|
|
}
|
|
|
|
static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function,
|
|
unsigned pin)
|
|
{
|
|
struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
|
|
struct pmic_mpp_pad *pad;
|
|
unsigned int val;
|
|
int ret;
|
|
|
|
pad = pctldev->desc->pins[pin].drv_data;
|
|
|
|
pad->function = function;
|
|
|
|
ret = pmic_mpp_write_mode_ctl(state, pad);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
|
|
|
|
return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val);
|
|
}
|
|
|
|
static const struct pinmux_ops pmic_mpp_pinmux_ops = {
|
|
.get_functions_count = pmic_mpp_get_functions_count,
|
|
.get_function_name = pmic_mpp_get_function_name,
|
|
.get_function_groups = pmic_mpp_get_function_groups,
|
|
.set_mux = pmic_mpp_set_mux,
|
|
};
|
|
|
|
static int pmic_mpp_config_get(struct pinctrl_dev *pctldev,
|
|
unsigned int pin, unsigned long *config)
|
|
{
|
|
unsigned param = pinconf_to_config_param(*config);
|
|
struct pmic_mpp_pad *pad;
|
|
unsigned arg = 0;
|
|
|
|
pad = pctldev->desc->pins[pin].drv_data;
|
|
|
|
switch (param) {
|
|
case PIN_CONFIG_BIAS_DISABLE:
|
|
if (pad->pullup != PMIC_MPP_PULL_UP_OPEN)
|
|
return -EINVAL;
|
|
arg = 1;
|
|
break;
|
|
case PIN_CONFIG_BIAS_PULL_UP:
|
|
switch (pad->pullup) {
|
|
case PMIC_MPP_PULL_UP_0P6KOHM:
|
|
arg = 600;
|
|
break;
|
|
case PMIC_MPP_PULL_UP_10KOHM:
|
|
arg = 10000;
|
|
break;
|
|
case PMIC_MPP_PULL_UP_30KOHM:
|
|
arg = 30000;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
break;
|
|
case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
|
|
if (pad->is_enabled)
|
|
return -EINVAL;
|
|
arg = 1;
|
|
break;
|
|
case PIN_CONFIG_POWER_SOURCE:
|
|
arg = pad->power_source;
|
|
break;
|
|
case PIN_CONFIG_INPUT_ENABLE:
|
|
if (!pad->input_enabled)
|
|
return -EINVAL;
|
|
arg = 1;
|
|
break;
|
|
case PIN_CONFIG_OUTPUT:
|
|
arg = pad->out_value;
|
|
break;
|
|
case PMIC_MPP_CONF_DTEST_SELECTOR:
|
|
arg = pad->dtest;
|
|
break;
|
|
case PMIC_MPP_CONF_AMUX_ROUTE:
|
|
arg = pad->amux_input;
|
|
break;
|
|
case PMIC_MPP_CONF_PAIRED:
|
|
if (!pad->paired)
|
|
return -EINVAL;
|
|
arg = 1;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_STRENGTH:
|
|
arg = pad->drive_strength;
|
|
break;
|
|
case PMIC_MPP_CONF_ANALOG_LEVEL:
|
|
arg = pad->aout_level;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* Convert register value to pinconf value */
|
|
*config = pinconf_to_config_packed(param, arg);
|
|
return 0;
|
|
}
|
|
|
|
static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
|
|
unsigned long *configs, unsigned nconfs)
|
|
{
|
|
struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
|
|
struct pmic_mpp_pad *pad;
|
|
unsigned param, arg;
|
|
unsigned int val;
|
|
int i, ret;
|
|
|
|
pad = pctldev->desc->pins[pin].drv_data;
|
|
|
|
/* Make it possible to enable the pin, by not setting high impedance */
|
|
pad->is_enabled = true;
|
|
|
|
for (i = 0; i < nconfs; i++) {
|
|
param = pinconf_to_config_param(configs[i]);
|
|
arg = pinconf_to_config_argument(configs[i]);
|
|
|
|
switch (param) {
|
|
case PIN_CONFIG_BIAS_DISABLE:
|
|
pad->pullup = PMIC_MPP_PULL_UP_OPEN;
|
|
break;
|
|
case PIN_CONFIG_BIAS_PULL_UP:
|
|
switch (arg) {
|
|
case 600:
|
|
pad->pullup = PMIC_MPP_PULL_UP_0P6KOHM;
|
|
break;
|
|
case 10000:
|
|
pad->pullup = PMIC_MPP_PULL_UP_10KOHM;
|
|
break;
|
|
case 30000:
|
|
pad->pullup = PMIC_MPP_PULL_UP_30KOHM;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
break;
|
|
case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
|
|
pad->is_enabled = false;
|
|
break;
|
|
case PIN_CONFIG_POWER_SOURCE:
|
|
if (arg >= pad->num_sources)
|
|
return -EINVAL;
|
|
pad->power_source = arg;
|
|
break;
|
|
case PIN_CONFIG_INPUT_ENABLE:
|
|
pad->input_enabled = arg ? true : false;
|
|
break;
|
|
case PIN_CONFIG_OUTPUT:
|
|
pad->output_enabled = true;
|
|
pad->out_value = arg;
|
|
break;
|
|
case PMIC_MPP_CONF_DTEST_SELECTOR:
|
|
pad->dtest = arg;
|
|
break;
|
|
case PIN_CONFIG_DRIVE_STRENGTH:
|
|
pad->drive_strength = arg;
|
|
break;
|
|
case PMIC_MPP_CONF_AMUX_ROUTE:
|
|
if (arg >= PMIC_MPP_AMUX_ROUTE_ABUS4)
|
|
return -EINVAL;
|
|
pad->amux_input = arg;
|
|
break;
|
|
case PMIC_MPP_CONF_ANALOG_LEVEL:
|
|
pad->aout_level = arg;
|
|
break;
|
|
case PMIC_MPP_CONF_PAIRED:
|
|
pad->paired = !!arg;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
val = pad->power_source << PMIC_MPP_REG_VIN_SHIFT;
|
|
|
|
ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_VIN_CTL, val);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if (pad->has_pullup) {
|
|
val = pad->pullup << PMIC_MPP_REG_PULL_SHIFT;
|
|
|
|
ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_PULL_CTL,
|
|
val);
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
|
|
val = pad->amux_input & PMIC_MPP_REG_AIN_ROUTE_MASK;
|
|
|
|
ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AIN_CTL, val);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AOUT_CTL, pad->aout_level);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = pmic_mpp_write_mode_ctl(state, pad);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_SINK_CTL, pad->drive_strength);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
|
|
|
|
return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val);
|
|
}
|
|
|
|
static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
|
|
struct seq_file *s, unsigned pin)
|
|
{
|
|
struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
|
|
struct pmic_mpp_pad *pad;
|
|
int ret;
|
|
|
|
static const char *const biases[] = {
|
|
"0.6kOhm", "10kOhm", "30kOhm", "Disabled"
|
|
};
|
|
|
|
pad = pctldev->desc->pins[pin].drv_data;
|
|
|
|
seq_printf(s, " mpp%-2d:", pin + PMIC_MPP_PHYSICAL_OFFSET);
|
|
|
|
if (!pad->is_enabled) {
|
|
seq_puts(s, " ---");
|
|
} else {
|
|
|
|
if (pad->input_enabled) {
|
|
ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS);
|
|
if (ret < 0)
|
|
return;
|
|
|
|
ret &= PMIC_MPP_REG_RT_STS_VAL_MASK;
|
|
pad->out_value = ret;
|
|
}
|
|
|
|
seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
|
|
seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]);
|
|
seq_printf(s, " vin-%d", pad->power_source);
|
|
seq_printf(s, " %d", pad->aout_level);
|
|
if (pad->has_pullup)
|
|
seq_printf(s, " %-8s", biases[pad->pullup]);
|
|
seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
|
|
if (pad->dtest)
|
|
seq_printf(s, " dtest%d", pad->dtest);
|
|
if (pad->paired)
|
|
seq_puts(s, " paired");
|
|
}
|
|
}
|
|
|
|
static const struct pinconf_ops pmic_mpp_pinconf_ops = {
|
|
.is_generic = true,
|
|
.pin_config_group_get = pmic_mpp_config_get,
|
|
.pin_config_group_set = pmic_mpp_config_set,
|
|
.pin_config_group_dbg_show = pmic_mpp_config_dbg_show,
|
|
};
|
|
|
|
static int pmic_mpp_direction_input(struct gpio_chip *chip, unsigned pin)
|
|
{
|
|
struct pmic_mpp_state *state = gpiochip_get_data(chip);
|
|
unsigned long config;
|
|
|
|
config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1);
|
|
|
|
return pmic_mpp_config_set(state->ctrl, pin, &config, 1);
|
|
}
|
|
|
|
static int pmic_mpp_direction_output(struct gpio_chip *chip,
|
|
unsigned pin, int val)
|
|
{
|
|
struct pmic_mpp_state *state = gpiochip_get_data(chip);
|
|
unsigned long config;
|
|
|
|
config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val);
|
|
|
|
return pmic_mpp_config_set(state->ctrl, pin, &config, 1);
|
|
}
|
|
|
|
static int pmic_mpp_get(struct gpio_chip *chip, unsigned pin)
|
|
{
|
|
struct pmic_mpp_state *state = gpiochip_get_data(chip);
|
|
struct pmic_mpp_pad *pad;
|
|
int ret;
|
|
|
|
pad = state->ctrl->desc->pins[pin].drv_data;
|
|
|
|
if (pad->input_enabled) {
|
|
ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK;
|
|
}
|
|
|
|
return !!pad->out_value;
|
|
}
|
|
|
|
static void pmic_mpp_set(struct gpio_chip *chip, unsigned pin, int value)
|
|
{
|
|
struct pmic_mpp_state *state = gpiochip_get_data(chip);
|
|
unsigned long config;
|
|
|
|
config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value);
|
|
|
|
pmic_mpp_config_set(state->ctrl, pin, &config, 1);
|
|
}
|
|
|
|
static int pmic_mpp_of_xlate(struct gpio_chip *chip,
|
|
const struct of_phandle_args *gpio_desc,
|
|
u32 *flags)
|
|
{
|
|
if (chip->of_gpio_n_cells < 2)
|
|
return -EINVAL;
|
|
|
|
if (flags)
|
|
*flags = gpio_desc->args[1];
|
|
|
|
return gpio_desc->args[0] - PMIC_MPP_PHYSICAL_OFFSET;
|
|
}
|
|
|
|
static void pmic_mpp_dbg_show(struct seq_file *s, struct gpio_chip *chip)
|
|
{
|
|
struct pmic_mpp_state *state = gpiochip_get_data(chip);
|
|
unsigned i;
|
|
|
|
for (i = 0; i < chip->ngpio; i++) {
|
|
pmic_mpp_config_dbg_show(state->ctrl, s, i);
|
|
seq_puts(s, "\n");
|
|
}
|
|
}
|
|
|
|
static const struct gpio_chip pmic_mpp_gpio_template = {
|
|
.direction_input = pmic_mpp_direction_input,
|
|
.direction_output = pmic_mpp_direction_output,
|
|
.get = pmic_mpp_get,
|
|
.set = pmic_mpp_set,
|
|
.request = gpiochip_generic_request,
|
|
.free = gpiochip_generic_free,
|
|
.of_xlate = pmic_mpp_of_xlate,
|
|
.dbg_show = pmic_mpp_dbg_show,
|
|
};
|
|
|
|
static int pmic_mpp_populate(struct pmic_mpp_state *state,
|
|
struct pmic_mpp_pad *pad)
|
|
{
|
|
int type, subtype, val, dir;
|
|
unsigned int sel;
|
|
|
|
type = pmic_mpp_read(state, pad, PMIC_MPP_REG_TYPE);
|
|
if (type < 0)
|
|
return type;
|
|
|
|
if (type != PMIC_MPP_TYPE) {
|
|
dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n",
|
|
type, pad->base);
|
|
return -ENODEV;
|
|
}
|
|
|
|
subtype = pmic_mpp_read(state, pad, PMIC_MPP_REG_SUBTYPE);
|
|
if (subtype < 0)
|
|
return subtype;
|
|
|
|
switch (subtype) {
|
|
case PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT:
|
|
case PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT:
|
|
case PMIC_MPP_SUBTYPE_4CH_NO_SINK:
|
|
case PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK:
|
|
case PMIC_MPP_SUBTYPE_4CH_FULL_FUNC:
|
|
pad->num_sources = 4;
|
|
break;
|
|
case PMIC_MPP_SUBTYPE_8CH_FULL_FUNC:
|
|
pad->num_sources = 8;
|
|
break;
|
|
default:
|
|
dev_err(state->dev, "unknown MPP type 0x%x at 0x%x\n",
|
|
subtype, pad->base);
|
|
return -ENODEV;
|
|
}
|
|
|
|
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_MODE_CTL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
pad->out_value = val & PMIC_MPP_REG_MODE_VALUE_MASK;
|
|
|
|
dir = val >> PMIC_MPP_REG_MODE_DIR_SHIFT;
|
|
dir &= PMIC_MPP_REG_MODE_DIR_MASK;
|
|
|
|
switch (dir) {
|
|
case PMIC_MPP_MODE_DIGITAL_INPUT:
|
|
pad->input_enabled = true;
|
|
pad->output_enabled = false;
|
|
pad->function = PMIC_MPP_DIGITAL;
|
|
break;
|
|
case PMIC_MPP_MODE_DIGITAL_OUTPUT:
|
|
pad->input_enabled = false;
|
|
pad->output_enabled = true;
|
|
pad->function = PMIC_MPP_DIGITAL;
|
|
break;
|
|
case PMIC_MPP_MODE_DIGITAL_BIDIR:
|
|
pad->input_enabled = true;
|
|
pad->output_enabled = true;
|
|
pad->function = PMIC_MPP_DIGITAL;
|
|
break;
|
|
case PMIC_MPP_MODE_ANALOG_BIDIR:
|
|
pad->input_enabled = true;
|
|
pad->output_enabled = true;
|
|
pad->function = PMIC_MPP_ANALOG;
|
|
break;
|
|
case PMIC_MPP_MODE_ANALOG_INPUT:
|
|
pad->input_enabled = true;
|
|
pad->output_enabled = false;
|
|
pad->function = PMIC_MPP_ANALOG;
|
|
break;
|
|
case PMIC_MPP_MODE_ANALOG_OUTPUT:
|
|
pad->input_enabled = false;
|
|
pad->output_enabled = true;
|
|
pad->function = PMIC_MPP_ANALOG;
|
|
break;
|
|
case PMIC_MPP_MODE_CURRENT_SINK:
|
|
pad->input_enabled = false;
|
|
pad->output_enabled = true;
|
|
pad->function = PMIC_MPP_SINK;
|
|
break;
|
|
default:
|
|
dev_err(state->dev, "unknown MPP direction\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
sel = val >> PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
|
|
sel &= PMIC_MPP_REG_MODE_FUNCTION_MASK;
|
|
|
|
if (sel >= PMIC_MPP_SELECTOR_DTEST_FIRST)
|
|
pad->dtest = sel + 1;
|
|
else if (sel == PMIC_MPP_SELECTOR_PAIRED)
|
|
pad->paired = true;
|
|
|
|
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_VIN_CTL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
pad->power_source = val >> PMIC_MPP_REG_VIN_SHIFT;
|
|
pad->power_source &= PMIC_MPP_REG_VIN_MASK;
|
|
|
|
if (subtype != PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT &&
|
|
subtype != PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK) {
|
|
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_PULL_CTL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
pad->pullup = val >> PMIC_MPP_REG_PULL_SHIFT;
|
|
pad->pullup &= PMIC_MPP_REG_PULL_MASK;
|
|
pad->has_pullup = true;
|
|
}
|
|
|
|
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AIN_CTL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
pad->amux_input = val >> PMIC_MPP_REG_AIN_ROUTE_SHIFT;
|
|
pad->amux_input &= PMIC_MPP_REG_AIN_ROUTE_MASK;
|
|
|
|
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_SINK_CTL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
pad->drive_strength = val;
|
|
|
|
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AOUT_CTL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
pad->aout_level = val;
|
|
|
|
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
pad->is_enabled = !!val;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int pmic_mpp_domain_translate(struct irq_domain *domain,
|
|
struct irq_fwspec *fwspec,
|
|
unsigned long *hwirq,
|
|
unsigned int *type)
|
|
{
|
|
struct pmic_mpp_state *state = container_of(domain->host_data,
|
|
struct pmic_mpp_state,
|
|
chip);
|
|
|
|
if (fwspec->param_count != 2 ||
|
|
fwspec->param[0] < 1 || fwspec->param[0] > state->chip.ngpio)
|
|
return -EINVAL;
|
|
|
|
*hwirq = fwspec->param[0] - PMIC_MPP_PHYSICAL_OFFSET;
|
|
*type = fwspec->param[1];
|
|
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int pmic_mpp_child_offset_to_irq(struct gpio_chip *chip,
|
|
unsigned int offset)
|
|
{
|
|
return offset + PMIC_MPP_PHYSICAL_OFFSET;
|
|
}
|
|
|
|
static int pmic_mpp_child_to_parent_hwirq(struct gpio_chip *chip,
|
|
unsigned int child_hwirq,
|
|
unsigned int child_type,
|
|
unsigned int *parent_hwirq,
|
|
unsigned int *parent_type)
|
|
{
|
|
*parent_hwirq = child_hwirq + 0xc0;
|
|
*parent_type = child_type;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void pmic_mpp_irq_mask(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
|
|
irq_chip_mask_parent(d);
|
|
gpiochip_disable_irq(gc, irqd_to_hwirq(d));
|
|
}
|
|
|
|
static void pmic_mpp_irq_unmask(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
|
|
gpiochip_enable_irq(gc, irqd_to_hwirq(d));
|
|
irq_chip_unmask_parent(d);
|
|
}
|
|
|
|
static const struct irq_chip pmic_mpp_irq_chip = {
|
|
.name = "spmi-mpp",
|
|
.irq_ack = irq_chip_ack_parent,
|
|
.irq_mask = pmic_mpp_irq_mask,
|
|
.irq_unmask = pmic_mpp_irq_unmask,
|
|
.irq_set_type = irq_chip_set_type_parent,
|
|
.irq_set_wake = irq_chip_set_wake_parent,
|
|
.flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_IMMUTABLE,
|
|
GPIOCHIP_IRQ_RESOURCE_HELPERS,
|
|
};
|
|
|
|
static int pmic_mpp_probe(struct platform_device *pdev)
|
|
{
|
|
struct irq_domain *parent_domain;
|
|
struct device_node *parent_node;
|
|
struct device *dev = &pdev->dev;
|
|
struct pinctrl_pin_desc *pindesc;
|
|
struct pinctrl_desc *pctrldesc;
|
|
struct pmic_mpp_pad *pad, *pads;
|
|
struct pmic_mpp_state *state;
|
|
struct gpio_irq_chip *girq;
|
|
int ret, npins, i;
|
|
u32 reg;
|
|
|
|
ret = of_property_read_u32(dev->of_node, "reg", ®);
|
|
if (ret < 0) {
|
|
dev_err(dev, "missing base address");
|
|
return ret;
|
|
}
|
|
|
|
npins = (uintptr_t) device_get_match_data(&pdev->dev);
|
|
|
|
BUG_ON(npins > ARRAY_SIZE(pmic_mpp_groups));
|
|
|
|
state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
|
|
if (!state)
|
|
return -ENOMEM;
|
|
|
|
platform_set_drvdata(pdev, state);
|
|
|
|
state->dev = &pdev->dev;
|
|
state->map = dev_get_regmap(dev->parent, NULL);
|
|
|
|
pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL);
|
|
if (!pindesc)
|
|
return -ENOMEM;
|
|
|
|
pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL);
|
|
if (!pads)
|
|
return -ENOMEM;
|
|
|
|
pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL);
|
|
if (!pctrldesc)
|
|
return -ENOMEM;
|
|
|
|
pctrldesc->pctlops = &pmic_mpp_pinctrl_ops;
|
|
pctrldesc->pmxops = &pmic_mpp_pinmux_ops;
|
|
pctrldesc->confops = &pmic_mpp_pinconf_ops;
|
|
pctrldesc->owner = THIS_MODULE;
|
|
pctrldesc->name = dev_name(dev);
|
|
pctrldesc->pins = pindesc;
|
|
pctrldesc->npins = npins;
|
|
|
|
pctrldesc->num_custom_params = ARRAY_SIZE(pmic_mpp_bindings);
|
|
pctrldesc->custom_params = pmic_mpp_bindings;
|
|
#ifdef CONFIG_DEBUG_FS
|
|
pctrldesc->custom_conf_items = pmic_conf_items;
|
|
#endif
|
|
|
|
for (i = 0; i < npins; i++, pindesc++) {
|
|
pad = &pads[i];
|
|
pindesc->drv_data = pad;
|
|
pindesc->number = i;
|
|
pindesc->name = pmic_mpp_groups[i];
|
|
|
|
pad->base = reg + i * PMIC_MPP_ADDRESS_RANGE;
|
|
|
|
ret = pmic_mpp_populate(state, pad);
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
|
|
state->chip = pmic_mpp_gpio_template;
|
|
state->chip.parent = dev;
|
|
state->chip.base = -1;
|
|
state->chip.ngpio = npins;
|
|
state->chip.label = dev_name(dev);
|
|
state->chip.of_gpio_n_cells = 2;
|
|
state->chip.can_sleep = false;
|
|
|
|
state->ctrl = devm_pinctrl_register(dev, pctrldesc, state);
|
|
if (IS_ERR(state->ctrl))
|
|
return PTR_ERR(state->ctrl);
|
|
|
|
parent_node = of_irq_find_parent(state->dev->of_node);
|
|
if (!parent_node)
|
|
return -ENXIO;
|
|
|
|
parent_domain = irq_find_host(parent_node);
|
|
of_node_put(parent_node);
|
|
if (!parent_domain)
|
|
return -ENXIO;
|
|
|
|
girq = &state->chip.irq;
|
|
gpio_irq_chip_set_chip(girq, &pmic_mpp_irq_chip);
|
|
girq->default_type = IRQ_TYPE_NONE;
|
|
girq->handler = handle_level_irq;
|
|
girq->fwnode = dev_fwnode(state->dev);
|
|
girq->parent_domain = parent_domain;
|
|
girq->child_to_parent_hwirq = pmic_mpp_child_to_parent_hwirq;
|
|
girq->populate_parent_alloc_arg = gpiochip_populate_parent_fwspec_fourcell;
|
|
girq->child_offset_to_irq = pmic_mpp_child_offset_to_irq;
|
|
girq->child_irq_domain_ops.translate = pmic_mpp_domain_translate;
|
|
|
|
ret = gpiochip_add_data(&state->chip, state);
|
|
if (ret) {
|
|
dev_err(state->dev, "can't add gpio chip\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, npins);
|
|
if (ret) {
|
|
dev_err(dev, "failed to add pin range\n");
|
|
goto err_range;
|
|
}
|
|
|
|
return 0;
|
|
|
|
err_range:
|
|
gpiochip_remove(&state->chip);
|
|
return ret;
|
|
}
|
|
|
|
static void pmic_mpp_remove(struct platform_device *pdev)
|
|
{
|
|
struct pmic_mpp_state *state = platform_get_drvdata(pdev);
|
|
|
|
gpiochip_remove(&state->chip);
|
|
}
|
|
|
|
static const struct of_device_id pmic_mpp_of_match[] = {
|
|
{ .compatible = "qcom,pm8019-mpp", .data = (void *) 6 },
|
|
{ .compatible = "qcom,pm8226-mpp", .data = (void *) 8 },
|
|
{ .compatible = "qcom,pm8841-mpp", .data = (void *) 4 },
|
|
{ .compatible = "qcom,pm8916-mpp", .data = (void *) 4 },
|
|
{ .compatible = "qcom,pm8937-mpp", .data = (void *) 4 },
|
|
{ .compatible = "qcom,pm8941-mpp", .data = (void *) 8 },
|
|
{ .compatible = "qcom,pm8950-mpp", .data = (void *) 4 },
|
|
{ .compatible = "qcom,pmi8950-mpp", .data = (void *) 4 },
|
|
{ .compatible = "qcom,pm8994-mpp", .data = (void *) 8 },
|
|
{ .compatible = "qcom,pma8084-mpp", .data = (void *) 8 },
|
|
{ .compatible = "qcom,pmi8994-mpp", .data = (void *) 4 },
|
|
{ },
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(of, pmic_mpp_of_match);
|
|
|
|
static struct platform_driver pmic_mpp_driver = {
|
|
.driver = {
|
|
.name = "qcom-spmi-mpp",
|
|
.of_match_table = pmic_mpp_of_match,
|
|
},
|
|
.probe = pmic_mpp_probe,
|
|
.remove = pmic_mpp_remove,
|
|
};
|
|
|
|
module_platform_driver(pmic_mpp_driver);
|
|
|
|
MODULE_AUTHOR("Ivan T. Ivanov <iivanov@mm-sol.com>");
|
|
MODULE_DESCRIPTION("Qualcomm SPMI PMIC MPP pin control driver");
|
|
MODULE_ALIAS("platform:qcom-spmi-mpp");
|
|
MODULE_LICENSE("GPL v2");
|