mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
synced 2024-12-29 09:13:38 +00:00
d991f855cb
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
69 lines
2.2 KiB
Plaintext
69 lines
2.2 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0
|
|
#
|
|
# USB/ATM DSL configuration
|
|
#
|
|
|
|
menuconfig USB_ATM
|
|
tristate "USB DSL modem support"
|
|
depends on ATM
|
|
select CRC32
|
|
help
|
|
Say Y here if you want to connect a USB Digital Subscriber Line (DSL)
|
|
modem to your computer's USB port. You will then need to choose your
|
|
modem from the list below.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called usbatm.
|
|
|
|
if USB_ATM
|
|
|
|
config USB_SPEEDTOUCH
|
|
tristate "Speedtouch USB support"
|
|
select FW_LOADER
|
|
help
|
|
Say Y here if you have an SpeedTouch USB or SpeedTouch 330
|
|
modem. In order to use your modem you will need to install the
|
|
two parts of the firmware, extracted by the user space tools; see
|
|
<http://www.linux-usb.org/SpeedTouch/> for details.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called speedtch.
|
|
|
|
config USB_CXACRU
|
|
tristate "Conexant AccessRunner USB support"
|
|
select FW_LOADER
|
|
help
|
|
Say Y here if you have an ADSL USB modem based on the Conexant
|
|
AccessRunner chipset. In order to use your modem you will need to
|
|
install the firmware, extracted by the user space tools; see
|
|
<http://accessrunner.sourceforge.net/> for details.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called cxacru.
|
|
|
|
config USB_UEAGLEATM
|
|
tristate "ADI 930 and eagle USB DSL modem"
|
|
select FW_LOADER
|
|
help
|
|
Say Y here if you have an ADSL USB modem based on the ADI 930
|
|
or eagle chipset. In order to use your modem you will need to
|
|
install firmwares and CMV (Command Management Variables); see
|
|
<https://gna.org/projects/ueagleatm/> for details.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ueagle-atm.
|
|
|
|
config USB_XUSBATM
|
|
tristate "Other USB DSL modem support"
|
|
help
|
|
Say Y here if you have a DSL USB modem not explicitly supported by
|
|
another USB DSL drivers. In order to use your modem you will need to
|
|
pass the vendor ID, product ID, and endpoint numbers for transmission
|
|
and reception as module parameters. You may need to initialize
|
|
the modem using a user space utility (a firmware loader for example).
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called xusbatm.
|
|
|
|
endif # USB_ATM
|