Add this LM75 compatible sensor which needs a separate entry because of
its default sampling time and SMBusAlert handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20241218074131.4351-7-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MCU can be found on network-attached-storage devices made by QNAP
and provides access to fan control including reading back its RPM as
well as reading the temperature of the NAS case.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241107114712.538976-8-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
This value was found on an ASRock B650 Steel Legend WiFi with an
NCT6686D chip.
Signed-off-by: Max Ammann <max@maxammann.org>
Link: https://lore.kernel.org/r/20241214102201.122851-1-max@maxammann.org
[groeck: htmldocs fix]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add initial support for the Texas Instruments TPS25990 eFuse.
This adds the basic PMBUS telemetry support for the device.
From Karol Przybylski:
The tps25990_read_word_data function contains a block of unreachable code
caused by the syntactic structure in the PMBUS_VIRT_READ_IIN_MAX case.
Specifically, the return TPS25990_READ_IIN_PEAK; statement immediately
exits the function, making the next lines unreachable.
This patch removes the return statement, leaving the expected handling.
Discovered in coverity: CID 1602227
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[groeck: Adjust to MODULE_IMPORT_NS API change]
[karprzy7@gmail.com: Fix unreachable code in tps25990_read_word_data]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a module parameter to force the write protection mode of pmbus chips.
4 protections modes are provided to start with:
* 0: Remove the write protection
* 1: Disable all writes except to the WRITE_PROTECT, OPERATION,
PAGE, ON_OFF_CONFIG and VOUT_COMMAND commands
* 2: Disable all writes except to the WRITE_PROTECT, OPERATION and
PAGE commands
* 3: Disable all writes except to the WRITE_PROTECT command
Of course, if the parameter is not provided, the default write protection
status of the pmbus chips is left untouched.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing PMBus protected registers does succeed from the smbus perspective,
even if the write is ignored by the device and a communication fault is
raised. This fault will silently be caught and cleared by pmbus irq if one
has been registered.
This means that the regulator call may return succeed although the
operation was ignored.
With this change, the operation which are not supported will be properly
flagged as such and the regulator framework won't even try to execute them.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[groeck: Adjust to EXPORT_SYMBOL_NS_GPL API change]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
During the upstreaming process, the driver has been extended to report
the shunt voltage as well. Document that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add compatible string 'nxp,p3t1085' since p3t1085's register layout is the
same as tmp108.
The p3t1085 supports I3C interface.
Update document tmp108.rst and Kconfig's help context.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Message-ID: <20241111-p3t1085-v3-2-bff511550aad@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix some typos in hwmon/sch5627 and hwmon/max31827 reported by
checkpatch.pl. These changes are purely documentation cleanup with no
functional modifications.
Signed-off-by: Abhinav Saxena <xandfury@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Message-ID: <20241108212201.144482-1-xandfury@gmail.com>
[groeck: Updated subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix several grammatical issues in the fan speed trip points documentation:
- Replace awkward "which % the fan should run at at" construction with
clearer "that specify the percentage at which"
- Fix incorrect "is chip depended" to "are chip dependent" for correct
verb agreement and adjective form
- Improve readability by reorganizing first sentence and separating the
complex explanation into simpler parts
- Add hyphen before "see" to improve readability
- Remove redundant "at" in temperature description
No functional changes, documentation only.
Signed-off-by: Abhinav Saxena <xandfury@gmail.com>
Message-ID: <20241107013849.47833-1-xandfury@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PMBUS_NO_WRITE_PROTECT and PMBUS_USE_COEFFICIENTS_CMD flags have been added
to pmbus, but the corresponding documentation was not updated.
Update the documentation before adding new flags
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Message-ID: <20241105-tps25990-v4-1-0e312ac70b62@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SY24655: Support for current and voltage detection as well as
power calculation.
Signed-off-by: Wenliang Yan <wenliang202407@163.com>
Message-ID: <20241106150547.2538-1-wenliang202407@163.com>
[groeck: Changed order of compatible entries;
dropped spurious extra return statement in is_visible();
fixed code problems]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT7363Y is a fan controller which provides up to 16
independent FAN input monitors. It can report each FAN input count
values. The NCT7363Y also provides up to 16 independent PWM
outputs. Each PWM can output specific PWM signal by manual mode to
control the FAN duty outside.
Signed-off-by: Ban Feng <kcfeng0@nuvoton.com>
Message-ID: <20241022052905.4062682-3-kcfeng0@nuvoton.com>
[groeck: Dropped unnecessary variable initialization, and , after { }]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver for Renesas ISL28022 power monitor with I2C interface.
The device monitors voltage, current via shunt resistor
and calculated power.
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
Signed-off-by: Yikai Tsai <yikai.tsai.wiwynn@gmail.com>
Message-ID: <20241002081133.13123-3-yikai.tsai.wiwynn@gmail.com>
[groeck: Fixed alignment issues, dropped noise at end of probe]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for manipulating the internal heater of sht4x devices.
Enabling the heater removes condensed water from the sensor surface
which disturbs the relative humidity measurements.
The heater can operate at three heating levels (20, 110 or 200
milliwatts). Also, two heating durations may be selected (0.1 or 1s).
Once the heating time elapses the heater is automatically switched off.
Changes since v3:
* struct sht4x_data: add heating_complete timestamp
* struct sht4x_data: add data_pending flag
* heater_enable_store: return -EINVAL if input != 1
* heater_enable_store: check for data->heating_complete and update it
* heater_enable_store: set data_pending flag after heating request
* sht4x_read_values: msleep if heating in progress
* sht4x_read_values: dont send measurement request if data_pending
* heater_enable attr: make it RW
* Documentation: update info about heater_enable attr
Changes since v2:
* heater_enable_store: remove unnecessary if
* Documentation: remove incorrect info about turning off the heater
* be more specific in the patch description
Changes since v1:
* explain the use case of the new attributes set
* heater_enable attr: make it write-only
* heater_enable_store: define cmd as u8 instead of u8*
* heater_enable_store: remove unreachable data path
* heater_enable_store: remove unnecessary lock
* heater_enable_store: call i2c_master_send only if status==true
* define attributes as DEVICE_ATTR_* instead of SENSOR_DEVICE_ATTR_*
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Message-ID: <20240930205346.2147-1-apokusinski01@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA260 is similar to other chips of the series, except it has an internal
shunt resistor. The calibration register is therefore not present. Also,
the current register address was changed, though that does not matter for
the driver since the shunt voltage register (which is now the current
register) value is already used to read the current.
Cc: Loic Guegan <loic.guegan@mailbox.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
devm_hwmon_device_unregister() has no in-tree user, and its implementation
is wrong since it does not pass the to-be-removed hardware monitoring
device as parameter. I do not envision a valid use for it; drivers needing
it should not have called devm_hwmon_device_register_with_info() in the
first place. Remove it.
Reported-by: Matthew Sanders <m@ttsande.rs>
Closes: https://lore.kernel.org/linux-hwmon/488b3bdf870ea76c4b943dbe5fd15ac8113019dc.camel@kernel.org/
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While the chips supported by this driver do not directly support current
limits, they do support setting shunt voltage limits. The shunt voltage
divided by the shunt resistor value is the current. On top of that,
calibration values are set such that in the shunt voltage register and
the current register report the same values. That means we can report and
configure current limits based on shunt voltage limits, and we can do so
with much better accuracy than by setting shunt voltage limits.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SG2042 use an external MCU to provide basic hardware information
and thermal sensors.
Add driver support for the onboard MCU of SG2042.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Message-ID: <IA1PR20MB49536C786048D1E676BB9C20BB822@IA1PR20MB4953.namprd20.prod.outlook.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the OrangePi NEO-01. It uses different registers for PWM
manual mode, set PWM, and read fan speed than previous devices. Valid PWM
input and duty cycle is 1-244, we scale this from 1-255 to maintain
compatibility with the existing interface.
Add OneXPlayer 2 series, OneXFly, and X1 series models. The 2/X1 series use
new registers for turbo button takeover and read fan speed. X1 has an Intel
variant so change the CPU detection at init to only check for the affected
devices. While at it, adjust formatting of some constants and reorder all
cases alphabetically for consistency. Rename OXP_OLD constants to OXP_MINI
for disambiguation. Update code comments for clarity.
Add support for AYANEO models 2S, AIR 1S, Flip series, GEEK 1S, and KUN.
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Tested-by: Kevin Greenberg <kdgreenberg234@protonmail.com>
Tested-by: Joshua Tam <csinaction@pm.me>
Tested-by: Parth Menon <parthasarathymenon@gmail.com>
Tested-by: Philip Müller <philm@manjaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202408160329.TLNbIwRC-lkp@intel.com/
Message-ID: <20240822183525.27289-2-derekjohn.clark@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update datasheet references. Replace misleading 'force parameter needed'
with 'must be instantiated explicitly'. Explain the reason for the missing
auto-detection. Mention all supported chips in Kconfig.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for local caching, to hide register read/write address
differences, and for multi-byte operations. With this change,
the driver specific lock is no longer necessary.
While at it, check errors seen when initializing the chip and bail out
if chip initialization fails.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* Obsolete driver removals
- Removed obsolete adm1021 and max6642 drivers
* New drivers
- MPS MP2891
- MPS MP2993
- MPS MP9941
- MPS MP5920
- SPD5118 (Temperature Sensor and EEPROM)
* Added device support to existing drivers
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
* Notable enhancements and fixes
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827 drivers
* Various other minor fixes and improvements
-----BEGIN PGP SIGNATURE-----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=ebWS
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Obsolete driver removals:
- Removed obsolete adm1021 and max6642 drivers
New drivers:
- MPS MP2891, MP2993, MP9941, and MP5920
- SPD5118 (Temperature Sensor and EEPROM)
Added device support to existing drivers:
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
Notable enhancements and fixes:
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and
with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827
drivers
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (103 commits)
hwmon: (max6697) Fix swapped temp{1,8} critical alarms
hwmon: (max6697) Fix underflow when writing limit attributes
hwmon: Remove obsolete adm1021 and max6642 drivers
hwmon: (pmbus/ltc4286) Drop unused i2c device ids
hwmon: (g762) Initialize fans after configuring clock
hwmon: (amc6821) Add support for pwm1_mode attribute
hwmon: (amc6821) Convert to with_info API
hwmon: (amc6821) Convert to use regmap
hwmon: (amc6821) Drop unnecessary enum chips
hwmon: (amc6821) Use BIT() and GENMASK()
hwmon: (amc6821) Use tabs for column alignment in defines
hwmon: (amc6821) Reorder include files, drop unnecessary ones
hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
hwmon: (amc6821) Rename fan1_div to fan1_pulses
hwmon: (amc6821) Make reading and writing fan speed limits consistent
hwmon: (amc6821) Stop accepting invalid pwm values
hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
hwmon: (lm95234) Fix underflows seen when writing limit attributes
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
...
ADM1021, MAX6642, and compatible chips are supported by the lm90 driver.
Remove the obsolete stand-alone drivers to reduce maintenance overhead.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMC6821 supports configuring if a fan is DC or PWM controlled.
Add support for the pwm1_mode attribute to make it runtime configurable.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After setting fan1_target and setting pwm1_enable to 4,
the fan controller tries to achieve the requested fan speed.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip does not have a fan divisor. What it does have is a configuration
to set either 2 or 4 pulses per fan rotation. Rename the attribute to
reflect its use. Update documentation accordingly.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for MPS Hot-Swap controller mp5920. This driver exposes
telemetry and limit value readings and writings.
Signed-off-by: Alex Vdovydchenko <xzeol@yahoo.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240702115252.981416-3-xzeol@yahoo.com
[groeck: Use min_t() to limit length of displayed model string]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading SPD NVMEM data from SPD5118 (Jedec JESD300)
compliant memory modules. NVMEM write operation is not supported.
NVMEM support is optional. If CONFIG_NVMEM is disabled, the driver will
still instantiate but not provide NVMEM attribute files.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for SPD5118 (Jedec JESD300) compliant temperature
sensors. Such sensors are typically found on DDR5 memory modules.
Cc: René Rebe <rene@exactcode.de>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Stephen Horvath <s.horvath@outlook.com.au>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ChromeOS Embedded Controller exposes fan speed and temperature
readings.
Expose this data through the hwmon subsystem.
The driver is designed to be probed via the cros_ec mfd device.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240529-cros_ec-hwmon-v4-2-5cdf0c5db50a@weissschuh.net
[tzungbi: Fixed typo in MAINTAINERS: "chros_ec_hwmon" -> "cros_ec_hwmon"]
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Add the usb id of the HX1200i Series 2023. Update the documentation
accordingly. Also fix the version comments, there are no Series 2022
products. That are legacy or first version products going back many
many years.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/ZlAZs4u0dU7JxtDf@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reporting firmware and bootloader version using debugfs.
Update documentation accordingly.
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Link: https://lore.kernel.org/r/20240513194734.43040-2-mail@mariuszachmann.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1428 and EMC1438 are similar to EMC14xx, but have eight temperature
channels, as well as signed data and limit registers. Chips currently
supported by this driver have unsigned registers only.
Signed-off-by: Lars Petter Mostad <larspm@gmail.com>
Link: https://lore.kernel.org/r/20240510142824.824332-1-lars.petter.mostad@appear.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240430085654.1028864-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for NZXT Kraken 2023 (standard) and NZXT Kraken 2023 Elite
all-in-one CPU coolers. These models communicate identically to the NZXT
Kraken Z-series (Z53 code paths) in all cases except when writing the
fan curve, where setting additional bits in the report is needed.
Reviewed-by: Jonas Malaco <jonas@protocubo.io>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240428104812.14037-3-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
