If CONFIG_NET is not defined then THERMAL_NETLINK can't be selected.
Hence add dependency on CONFIG_NET. Othewise it will generate compile
errors while compiling thermal_netlink.c.
Fixes: 4596cbea0ed2 ("thermal: intel: Remove explicit user_space governor selection")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20241218214444.1904650-1-srinivas.pandruvada@linux.intel.com
[ rjw: Merge the "depends on" lines ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Panther Lake follows same register set as Lunar Lake. Enable feature
flags to support workload hints and power floor status.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20241216211810.1207028-2-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Panther Lake follows same register set as Lunar Lake for DLVR. Enable
feature flag to support DLVR.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/thermal: intel: int340x: Panther Lake DLVR support
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently some user space programs like Linux thermald needs to register
to get notifications from both thermal user space governor and also
Thermal netlink. This is required as some messages like HFI (Hardware
Feedback Notifications) requires Thermal netlink.
This results in additional processing in kernel and user space to process
both notifications. The cost of using user space governor using
kobject_uevent is much higher as this is also used by other user space
daemons like udev daemon.
Do not select user_space thermal governor by default. If it is present
user space programs can always use this governor by writing to
"policy" attribute.
Instead from the kernel select THERMAL_NETLINK. Trip temperature
violation can be received by user space programs via thermal netlink
events:
THERMAL_GENL_EVENT_TZ_TRIP_UP
THERMAL_GENL_EVENT_TZ_TRIP_DOWN
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20241216190821.1137162-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The group only contains a single entry and the conditionals around its
lifecycle make clear that this won't change.
Remove the unnecessary group.
This saves some memory and it's easier to read.
The removal of a non-const bin_attribute[] instance is also a
preparation for the constification of struct bin_attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20241121-sysfs-const-bin_attr-int340x_thermal-v1-1-2436facf9dae@weissschuh.net
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the current_uuid attribute is set to the active policy UUID,
reading back the same attribute is returning "INVALID" instead of
the active policy UUID on some platforms before Ice Lake.
In platforms before Ice Lake, firmware provides a list of supported
thermal policies. In this case, user space can select any of the
supported thermal policies via a write to attribute "current_uuid".
In commit c7ff29763989 ("thermal: int340x: Update OS policy capability
handshake")', the OS policy handshake was updated to support Ice Lake
and later platforms and it treated priv->current_uuid_index=0 as
invalid. However, priv->current_uuid_index=0 is for the active policy,
only priv->current_uuid_index=-1 is invalid.
Fix this issue by updating the priv->current_uuid_index check.
Fixes: c7ff29763989 ("thermal: int340x: Update OS policy capability handshake")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.18+ <stable@vger.kernel.org> # 5.18+
Link: https://patch.msgid.link/20241114200213.422303-1-srinivas.pandruvada@linux.intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add SAR2130P compatible to DT bindings in the QCom Tsens driver (Dmitry
Baryshkov).
- Add static annotation to arrays describing platform sensors in the
LVTS Mediatek driver (Colin Ian King).
- Switch back to struct platform_driver::remove() from the previous
callbacks prototype rework (Uwe Kleine-König).
- Add MSM8937 compatible to DT bindings and its support in the QCom
Tsens driver (Barnabás Czémán).
- Remove a pointless sign test on an unsigned value in k3_bgp_read_temp()
in the k3_j72xx_bandgap driver (Rex Nie).
- Fix a pointer reference loss when realloc() fails in the thermal
library (Zhang Jiao).
-----BEGIN PGP SIGNATURE-----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=cXi4
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These update a few thermal drivers used on ARM platforms and thermal
tools:
- Add SAR2130P compatible to DT bindings in the QCom Tsens driver
(Dmitry Baryshkov)
- Add static annotation to arrays describing platform sensors in the
LVTS Mediatek driver (Colin Ian King)
- Switch back to struct platform_driver::remove() from the previous
callbacks prototype rework (Uwe Kleine-König)
- Add MSM8937 compatible to DT bindings and its support in the QCom
Tsens driver (Barnabás Czémán)
- Remove a pointless sign test on an unsigned value in
k3_bgp_read_temp() in the k3_j72xx_bandgap driver (Rex Nie)
- Fix a pointer reference loss when realloc() fails in the thermal
library (Zhang Jiao)"
* tag 'thermal-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/thermal: Fix common realloc mistake
thermal/drivers/k3_j72xx_bandgap: Simplify code in k3_bgp_read_temp()
thermal/drivers/qcom/tsens-v1: Add support for MSM8937 tsens
dt-bindings: thermal: tsens: Add MSM8937
thermal: Switch back to struct platform_driver::remove()
thermal/drivers/mediatek/lvts_thermal: Make read-only arrays static const
dt-bindings: thermal: qcom-tsens: Add SAR2130P compatible
with the purpose of using such hints when making scheduling decisions
- Determine the boost enumerator for each AMD core based on its type: efficiency
or performance, in the cppc driver
- Add the type of a CPU to the topology CPU descriptor with the goal of
supporting and making decisions based on the type of the respective core
- Add a feature flag to denote AMD cores which have heterogeneous topology and
enable SD_ASYM_PACKING for those
- Check microcode revisions before disabling PCID on Intel
- Cleanups and fixlets
-----BEGIN PGP SIGNATURE-----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=420r
-----END PGP SIGNATURE-----
Merge tag 'x86_cpu_for_v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpuid updates from Borislav Petkov:
- Add a feature flag which denotes AMD CPUs supporting workload
classification with the purpose of using such hints when making
scheduling decisions
- Determine the boost enumerator for each AMD core based on its type:
efficiency or performance, in the cppc driver
- Add the type of a CPU to the topology CPU descriptor with the goal of
supporting and making decisions based on the type of the respective
core
- Add a feature flag to denote AMD cores which have heterogeneous
topology and enable SD_ASYM_PACKING for those
- Check microcode revisions before disabling PCID on Intel
- Cleanups and fixlets
* tag 'x86_cpu_for_v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Remove redundant CONFIG_NUMA guard around numa_add_cpu()
x86/cpu: Fix FAM5_QUARK_X1000 to use X86_MATCH_VFM()
x86/cpu: Fix formatting of cpuid_bits[] in scattered.c
x86/cpufeatures: Add X86_FEATURE_AMD_WORKLOAD_CLASS feature bit
x86/amd: Use heterogeneous core topology for identifying boost numerator
x86/cpu: Add CPU type to struct cpuinfo_topology
x86/cpu: Enable SD_ASYM_PACKING for PKG domain on AMD
x86/cpufeatures: Add X86_FEATURE_AMD_HETEROGENEOUS_CORES
x86/cpufeatures: Rename X86_FEATURE_FAST_CPPC to have AMD prefix
x86/mm: Don't disable PCID when INVLPG has been fixed by microcode
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/thermal to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way make a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241019163412.304422-2-u.kleine-koenig@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Similar to the MSR RAPL interface, MMIO RAPL supports PL4 too, so add
MMIO RAPL PL4d support to the processor_thermal driver.
As a result, the powercap sysfs for MMIO RAPL will show a new "peak
power" constraint.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-7-rui.zhang@intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPU0/package0 is always online and the MMIO RAPL driver runs on single
package systems only, so there is no need to handle CPU hotplug in it.
Always register a RAPL package device for package 0 and remove the
unnecessary CPU hotplug support.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240930081801.28502-6-rui.zhang@intel.com
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some Lunar Lake pre-production systems, not all the MSI thermal
vectors are valid. In that case instead of failing module load, continue
with partial thermal interrupt support.
pci_alloc_irq_vectors() can return less than expected maximum vectors.
In that case call devm_request_threaded_irq() only for current maximum
vectors.
Fixes: 7a9a8c5faf41 ("thermal: intel: int340x: Support MSI interrupt for Lunar Lake")
Reported-by: Yijun Shen <Yijun.Shen@dell.com>
Tested-by: Yijun Shen <Yijun.Shen@dell.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Link: https://patch.msgid.link/20240723140228.865919-3-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some pre-production Lunar Lake systems, there is a kernel
warning:
remove_proc_entry: removing non-empty directory 'irq/172'
WARNING: CPU: 0 PID: 501 at fs/proc/generic.c:717
remove_proc_entry+0x1b4/0x1e0
...
...
remove_proc_entry+0x1b4/0x1e0
report_bug+0x182/0x1b0
handle_bug+0x51/0xa0
exc_invalid_op+0x18/0x80
asm_exc_invalid_op+0x1b/0x20
remove_proc_entry+0x1b4/0x1e0
remove_proc_entry+0x1b4/0x1e0
unregister_irq_proc+0xf2/0x120
free_desc+0x41/0xe0
irq_domain_free_irqs+0x138/0x1c0
irq_free_descs+0x52/0x80
irq_domain_free_irqs+0x151/0x1c0
msi_domain_free_locked.part.0+0x17e/0x1c0
msi_domain_free_irqs_all_locked+0x74/0xc0
pci_msi_teardown_msi_irqs+0x50/0x60
pci_free_msi_irqs+0x12/0x40
pci_free_irq_vectors+0x58/0x70
On these systems, not all the MSI thermal vectors are valid. This causes
devm_request_threaded_irq() to fail for some vectors. As part of the
clean up on this error, pci_free_irq_vectors() is called without calling
devm_free_irq(). This causes the above warning.
Add a function proc_thermal_free_msi() to call devm_free_irq() for all
successfully registered IRQ handlers, then call pci_free_irq_vectors().
Call this function for MSI cleanup.
Fixes: 7a9a8c5faf41 ("thermal: intel: int340x: Support MSI interrupt for Lunar Lake")
Reported-by: Yijun Shen <Yijun.shen@dell.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Link: https://patch.msgid.link/20240723140228.865919-2-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge updates of Intel thermal drivers for 6.11-rc1:
- Switch Intel thermal drivers to new Intel CPU model defines (Tony
Luck).
- Clean up the int3400 and int3403 drivers (Erick Archer and David Alan
Gilbert).
- Improve intel_pch_thermal kernel log messages printed during suspend
to idle (Zhang Rui).
- Make the intel_tcc_cooling driver use a model-specific bitmask for
TCC offset (Ricardo Neri).
- Add DLVR and MSI interrupt support for the Lunar Lake platform to the
int340x thermal driver (Srinivas Pandruvada).
- Enable workload type hints (WLT) support and power floor interrupt
support for the Lunar Lake platform in int340x ((Srinivas Pandruvada).
- Make the HFI thermal driver use package scope for HFI instances as
per the Intel SDM (Zhang Rui).
* thermal-intel:
thermal: intel: hfi: Give HFI instances package scope
thermal: intel: int340x: Enable WLT and power floor support for Lunar Lake
thermal: intel: int340x: Support MSI interrupt for Lunar Lake
thermal: intel: int340x: Remove unnecessary calls to free irq
thermal: intel: int340x: Add DLVR support for Lunar Lake
thermal: intel: int340x: Capability to map user space to firmware values
thermal: intel: int340x: Cleanup of DLVR sysfs on driver remove
thermal: intel: intel_tcc_cooling: Use a model-specific bitmask for TCC offset
thermal: intel: intel_tcc: Add model checks for temperature registers
thermal: intel: intel_pch: Improve cooling log
thermal: int3403: remove unused struct 'int3403_performance_state'
thermal: int3400: Use sizeof(*pointer) instead of sizeof(type)
thermal: intel: intel_soc_dts_thermal: Switch to new Intel CPU model defines
thermal: intel: intel_tcc_cooling: Switch to new Intel CPU model defines
Out of several drivers implementing the .set_trip_temp() thermal zone
operation, three don't actually use the trip ID argument passed to it,
two call __thermal_zone_get_trip() to get a struct thermal_trip
corresponding to the given trip ID, and the other use the trip ID as an
index into their own data structures with the assumption that it will
always match the ordering of entries in the trips table passed to the
core during thermal zone registration, which is fragile and not really
guaranteed.
Even though the trip IDs used by the core are in fact their indices in the
trips table passed to it by the thermal zone creator, that is purely a
matter of convenience and should not be relied on for correctness.
For this reason, modify trip_point_temp_store() to pass a (const) trip
pointer to .set_trip_temp() and adjust the drivers implementing it
accordingly.
This helps to simplify the drivers invoking __thermal_zone_get_trip()
from their .set_trip_temp() callback functions because they will not
need to do it now and the other drivers can store their internal
trip indices in the priv field in struct thermal_trip and their
.set_trip_temp() callback functions can get those indices from there.
The intel_quark_dts thermal driver can instead use the trip type to
determine the requisite trip index.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/8392906.T7Z3S40VBb@rjwysocki.net
[ rjw: Add missing colon and 2 empty code lines ]
[ rjw: Add missing change in imx_thermal.c and adjust the changelog ]
[ rjw: Drop an unused local variable ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Intel Software Developer's Manual defines the scope of HFI (registers
and memory buffer) as a package. Use package scope(*) in the software
representation of an HFI instance.
Using die scope in HFI instances has the effect of creating multiple
conflicting instances for the same package: each instance allocates its
own memory buffer and configures the same package-level registers.
Specifically, only one of the allocated memory buffers can be set in the
MSR_IA32_HW_FEEDBACK_PTR register. CPUs get incorrect HFI data from the
table.
The problem does not affect current HFI-capable platforms because they
all have single-die processors.
(*) We used die scope for HFI instances because there had been
processors with packages enumerated as dies. None of those systems
supported HFI, though. If such a system emerged, it would need to
be quirked.
Co-developed-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Link: https://patch.msgid.link/20240703055445.125362-1-rui.zhang@intel.com
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers will need to store integers in the priv field of struct
thermal_trip, so add conversion macros for doing this in a consistent
way and switch over the int340x_thermal driver that already does it and
uses custom conversion functions to using the new macros.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/3297884.aeNJFYEL58@rjwysocki.net
The legacy PCI interrupt is no longer supported for processor thermal
device on Lunar Lake. The support is via MSI.
Add feature PROC_THERMAL_FEATURE_MSI_SUPPORT to support MSI feature per
generation. Define this feature for Lunar Lake processors.
There are 4 MSI sources:
0 - Package thermal
1 - DDR Thermal
2 - Power floor interrupt
3 - Workload type hint
On interrupt, check the source and call the corresponding handler.
Here don't need to call proc_thermal_check_wt_intr() and
proc_thermal_check_power_floor_intr() to check if the interrupt is for
those sources as there is a dedicated MSI interrupt.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240619172109.497639-3-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for DLVR (Digital Linear Voltage Regulator) for Lunar Lake.
There are no new sysfs attributes or difference in operation compared
to prior generations.
MMIO offset and bit positions are changed compared to Meteor Lake
processors. Also for two attributes dlvr_frequency_mhz and
dlvr_frequency_select, the value presented or accepted by the firmware
is not raw frequency value but an index.
For example:
RFI_FREQ_SELECT and RFI_FREQ
: 0 DLVR freq point 2227.2 MHz
: 1 DLVR freq point 2140 MHz
Hence create a mapping table for Lunar Lake to map user space values
to the firmware accepted values.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240619124600.491168-4-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To ensure compatibility between user inputs and firmware requirements,
a conversion mechanism is necessary for certain attributes. For instance,
on some platforms, the DLVR frequency must be translated into a predefined
index before being communicated to the firmware. On Lunar Lake platform:
RFI_FREQ_SELECT and RFI_FREQ:
Index 0 corresponds to a DLVR frequency of 2227.2 MHz
Index 1 corresponds to a DLVR frequency of 2140 MHz
Introduce a feature that enables the conversion of values between user
space inputs and firmware-accepted formats. This feature would also
facilitate the reverse process, converting firmware values back into user
friendly display values.
To support this functionality, a model-specific mapping table will be
utilized. When available, this table will provide the necessary
translations between user space values and firmware values, ensuring
seamless communication and accurate settings.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240619124600.491168-3-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When only DLVR enabled without DVFS, during driver remove,
proc_thermal_rfim_remove() is not called. Hence the DLVR sysfs is not
deleted.
On Lunar Lake DLVR is enabled without DVFS, hence this issue can be
reproduced.
Check also PROC_THERMAL_FEATURE_DLVR to call proc_thermal_rfim_remove().
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://patch.msgid.link/20240619124600.491168-2-srinivas.pandruvada@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The TCC offset field in the register MSR_TEMPERATURE_TARGET is not
architectural. The TCC library provides a model-specific bitmask. Use it to
determine the maximum TCC offset.
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Link: https://patch.msgid.link/20240614211606.5896-3-ricardo.neri-calderon@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The register MSR_TEMPERATURE_TARGET is not architectural. Its fields may be
defined differently for each processor model. TCC_OFFSET is an example of
such case.
Despite being specified as architectural, the registers IA32_[PACKAGE]_
THERM_STATUS have become model-specific: in recent processors, the
digital temperature readout uses bits [23:16] whereas the Intel Software
Developer's manual specifies bits [22:16].
Create an array of processor models and their bitmasks for TCC_OFFSET and
the digital temperature readout fields. Do not include recent processors.
Instead, use the bitmasks of these recent processors as default.
Use these model-specific bitmasks when reading TCC_OFFSET or the
temperature sensors.
Initialize a model-specific data structure during subsys_initcall() to
have it ready when thermal drivers are loaded.
Expose the new interface intel_tcc_get_offset_mask(). The
intel_tcc_cooling driver will use it.
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Link: https://patch.msgid.link/20240614211606.5896-2-ricardo.neri-calderon@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some systems the processor thermal device interrupt is shared with
other PCI devices. In this case return IRQ_NONE from the interrupt
handler when the interrupt is not for the processor thermal device.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: f0658708e863 ("thermal: int340x: processor_thermal: Use non MSI interrupts by default")
Cc: 6.7+ <stable@vger.kernel.org> # 6.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intel_pch_thermal cooling mechanism currently only provides one of
the following final conclusions:
1. intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [48C]
2. intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [49C] after 30700 ms delay
3. intel_pch_thermal 0000:00:12.0: CPU-PCH is hot [60C] after 60000 ms delay. S0ix might fail
4. intel_pch_thermal 0000:00:12.0: Wakeup event detected, abort cooling
This does not provide sufficient context about what is happening,
especially for case 4.
Add one line log to indicate when PCH overheats and the cooling delay
has started.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'int3403_performance_state' has never been used since the original
commit 4384b8fe162d ("Thermal: introduce int3403 thermal driver").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not
change the former (unlike the latter). This patch has no effect
on runtime behavior.
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
New CPU #defines encode vendor and family as well as model.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
New CPU #defines encode vendor and family as well as model.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the small set of driver core and kernfs changes for 6.10-rc1.
Nothing major here at all, just a small set of changes for some driver
core apis, and minor fixups. Included in here are:
- sysfs_bin_attr_simple_read() helper added and used
- device_show_string() helper added and used
All usages of these were acked by the various maintainers. Also in here
are:
- kernfs minor cleanup
- removed unused functions
- typo fix in documentation
- pay attention to sysfs_create_link() failures in module.c finally.
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZk3+hQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfTwCfUyHWkDZuZ7ehdtjzfmcd4EKZBK8An3AAV99G
ox8PXMxuFTaUEdT/69FQ
=2sEo
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the small set of driver core and kernfs changes for 6.10-rc1.
Nothing major here at all, just a small set of changes for some driver
core apis, and minor fixups. Included in here are:
- sysfs_bin_attr_simple_read() helper added and used
- device_show_string() helper added and used
All usages of these were acked by the various maintainers. Also in
here are:
- kernfs minor cleanup
- removed unused functions
- typo fix in documentation
- pay attention to sysfs_create_link() failures in module.c finally
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
device property: Fix a typo in the description of device_get_child_node_count()
kernfs: mount: Remove unnecessary ‘NULL’ values from knparent
scsi: Use device_show_string() helper for sysfs attributes
platform/x86: Use device_show_string() helper for sysfs attributes
perf: Use device_show_string() helper for sysfs attributes
IB/qib: Use device_show_string() helper for sysfs attributes
hwmon: Use device_show_string() helper for sysfs attributes
driver core: Add device_show_string() helper for sysfs attributes
treewide: Use sysfs_bin_attr_simple_read() helper
sysfs: Add sysfs_bin_attr_simple_read() helper
module: don't ignore sysfs_create_link() failures
driver core: Remove unused platform_notify, platform_notify_remove
- Add EINJ CXL error types to actbl1.h (Ben Cheatham).
- Add support for RAS2 table to ACPICA (Shiju Jose).
- Fix various spelling mistakes in text files and code comments in
ACPICA (Colin Ian King).
- Fix spelling and typos in ACPICA (Saket Dumbre).
- Modify ACPI_OBJECT_COMMON_HEADER (lijun).
- Add RISC-V RINTC affinity structure support to ACPICA (Haibo Xu).
- Fix CXL 3.0 structure (RDPAS) in the CEDT table (Hojin Nam).
- Add missin increment of registered GPE count to ACPICA (Daniil
Tatianin).
- Mark new ACPICA release 20240322 (Saket Dumbre).
- Add support for the AEST V2 table to ACPICA (Ruidong Tian).
- Disable -Wstringop-truncation for some ACPICA code in the kernel to
avoid a compiler warning that is not very useful (Arnd Bergmann).
- Make the kernel indicate support for several ACPI features that are
in fact supported to the platform firmware through _OSC and fix the
Generic Initiator Affinity _OSC bit (Armin Wolf).
- Make the ACPI core set the owner value for ACPI drivers, drop the
owner setting from a number of drivers and eliminate the owner
field from struct acpi_driver (Krzysztof Kozlowski).
- Rearrange fields in several structures to effectively eliminate
computations from container_of() in some cases (Andy Shevchenko).
- Do some assorted cleanups of the ACPI device enumeration code (Andy
Shevchenko).
- Make the ACPI device enumeration code skip devices with _STA values
clearly identified by the specification as invalid (Rafael Wysocki).
- Rework the handling of the NHLT table to simplify and clarify it and
drop some obsolete pieces (Cezary Rojewski).
- Add ACPI IRQ override quirks for Asus Vivobook Pro N6506MV, TongFang
GXxHRXx and GMxHGxx, and XMG APEX 17 M23 (Guenter Schafranek, Tamim
Khan, Christoffer Sandberg).
- Add reference to UEFI DSD Guide to the documentation related to the
ACPI handling of device properties (Sakari Ailus).
- Fix SRAT lookup of CFMWS ranges with numa_fill_memblks(), remove
lefover architecture-dependent code from the ACPI NUMA handling code
and simplify it on top of that (Robert Richter).
- Add a num-cs device property to specify the number of chip selects
for Intel Braswell to the ACPI LPSS (Intel SoC) driver and remove a
nested CONFIG_PM #ifdef from it (Andy Shevchenko).
- Move three x86-specific ACPI files to the x86 directory (Andy
Shevchenko).
- Mark SMO8810 accel on Dell XPS 15 9550 as always present and add a
PNP_UART1_SKIP quirk for Lenovo Blade2 tablets (Hans de Goede).
- Move acpi_blacklisted() declaration to asm/acpi.h (Kuppuswamy
Sathyanarayanan).
- Add Lunar Lake support to the ACPI DPTF driver (Sumeet Pawnikar).
- Mark the einj_driver driver's remove callback as __exit because it
cannot get unbound via sysfs (Uwe Kleine-König).
- Fix a typo in the ACPI documentation regarding the layout of sysfs
subdirectory representing the ACPI namespace (John Watts).
- Make the ACPI pfrut utility print the update_cap field during
capability query (Chen Yu).
- Add HAS_IOPORT dependencies to PNP (Niklas Schnelle).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmZCZksSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxQHMQAIaab/0AY6MXznyZtf9bfVXzwa/HXWJV
CWVhubByKHKSJjGcsMbxAXvRq5EDX91QiuaoExEzKY7G9q+jFl1rUMvGWVrySveS
ae1+jMF9Kd3QXTXB6bCbre4/7bn/LZN0U5nvD5yFpuEEl8GqGafKiUVRVEIQmMuB
1yi5HU2orKxLYU84mCGIiiWlTAi/6MlSeJ5NZwxPfj/+B24pPWTdu4AsD+b7gC2G
g36KlAZpnGJqRZ1pg5KQDCV0eKGCJuh9X7ACM8t/XDg4S7FL75X2fWMRUh+4sYp9
12DdxaEPYCNaVebm2Ae7vrLtcifHNsMoirs3Me0RUOmFqRPaH5YILw3Un2jabiBp
OWgVuIAa1+M4pKoVVnimM1f9i8rUr8XEl/kheb0c0OinQlecYpPeza9T5U+mMOsy
knOs5jTm5oIhHS4sQxPu4I1/HX4/5kczDuMs1XW+6ypuT28WCbTj+mrryAQOQHyD
vFsDBdInU5Yiit4APuJjiTSeEtFkClNI54oKz29mesPRRdDMuYBubdEuXG4lbsF1
n4SWds3ELFqWlWvyshCMQdyjTN7UUMc2Af+xY3AEIq7uvPTdTQWUmf5LQi2vfgSO
y3vhCjjt0ONyTXqbkP7HYcOXx5DZsFb/1uXqAAo4/RlZ6LWx/K1+onttECsoQIRH
rR3pwW76z0Vy
=UiEQ
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are ACPICA updates coming from the 20240322 release upstream, an
ACPI DPTF driver update adding new platform support for it, some new
quirks and some assorted fixes and cleanups.
Specifics:
- Add EINJ CXL error types to actbl1.h (Ben Cheatham)
- Add support for RAS2 table to ACPICA (Shiju Jose)
- Fix various spelling mistakes in text files and code comments in
ACPICA (Colin Ian King)
- Fix spelling and typos in ACPICA (Saket Dumbre)
- Modify ACPI_OBJECT_COMMON_HEADER (lijun)
- Add RISC-V RINTC affinity structure support to ACPICA (Haibo Xu)
- Fix CXL 3.0 structure (RDPAS) in the CEDT table (Hojin Nam)
- Add missin increment of registered GPE count to ACPICA (Daniil
Tatianin)
- Mark new ACPICA release 20240322 (Saket Dumbre)
- Add support for the AEST V2 table to ACPICA (Ruidong Tian)
- Disable -Wstringop-truncation for some ACPICA code in the kernel to
avoid a compiler warning that is not very useful (Arnd Bergmann)
- Make the kernel indicate support for several ACPI features that are
in fact supported to the platform firmware through _OSC and fix the
Generic Initiator Affinity _OSC bit (Armin Wolf)
- Make the ACPI core set the owner value for ACPI drivers, drop the
owner setting from a number of drivers and eliminate the owner
field from struct acpi_driver (Krzysztof Kozlowski)
- Rearrange fields in several structures to effectively eliminate
computations from container_of() in some cases (Andy Shevchenko)
- Do some assorted cleanups of the ACPI device enumeration code (Andy
Shevchenko)
- Make the ACPI device enumeration code skip devices with _STA values
clearly identified by the specification as invalid (Rafael Wysocki)
- Rework the handling of the NHLT table to simplify and clarify it
and drop some obsolete pieces (Cezary Rojewski)
- Add ACPI IRQ override quirks for Asus Vivobook Pro N6506MV,
TongFang GXxHRXx and GMxHGxx, and XMG APEX 17 M23 (Guenter
Schafranek, Tamim Khan, Christoffer Sandberg)
- Add reference to UEFI DSD Guide to the documentation related to the
ACPI handling of device properties (Sakari Ailus)
- Fix SRAT lookup of CFMWS ranges with numa_fill_memblks(), remove
lefover architecture-dependent code from the ACPI NUMA handling
code and simplify it on top of that (Robert Richter)
- Add a num-cs device property to specify the number of chip selects
for Intel Braswell to the ACPI LPSS (Intel SoC) driver and remove a
nested CONFIG_PM #ifdef from it (Andy Shevchenko)
- Move three x86-specific ACPI files to the x86 directory (Andy
Shevchenko)
- Mark SMO8810 accel on Dell XPS 15 9550 as always present and add a
PNP_UART1_SKIP quirk for Lenovo Blade2 tablets (Hans de Goede)
- Move acpi_blacklisted() declaration to asm/acpi.h (Kuppuswamy
Sathyanarayanan)
- Add Lunar Lake support to the ACPI DPTF driver (Sumeet Pawnikar)
- Mark the einj_driver driver's remove callback as __exit because it
cannot get unbound via sysfs (Uwe Kleine-König)
- Fix a typo in the ACPI documentation regarding the layout of sysfs
subdirectory representing the ACPI namespace (John Watts)
- Make the ACPI pfrut utility print the update_cap field during
capability query (Chen Yu)
- Add HAS_IOPORT dependencies to PNP (Niklas Schnelle)"
* tag 'acpi-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (72 commits)
ACPI/NUMA: Squash acpi_numa_memory_affinity_init() into acpi_parse_memory_affinity()
ACPI/NUMA: Squash acpi_numa_slit_init() into acpi_parse_slit()
ACPI/NUMA: Remove architecture dependent remainings
x86/numa: Fix SRAT lookup of CFMWS ranges with numa_fill_memblks()
ACPI: video: Add backlight=native quirk for Lenovo Slim 7 16ARH7
ACPI: scan: Avoid enumerating devices with clearly invalid _STA values
ACPI: Move acpi_blacklisted() declaration to asm/acpi.h
ACPI: resource: Skip IRQ override on Asus Vivobook Pro N6506MV
ACPICA: AEST: Add support for the AEST V2 table
ACPI: tools: pfrut: Print the update_cap field during capability query
ACPI: property: Add reference to UEFI DSD Guide
Documentation: firmware-guide: ACPI: Fix namespace typo
PNP: add HAS_IOPORT dependencies
ACPI: resource: Do IRQ override on TongFang GXxHRXx and GMxHGxx
ACPI: resource: Do IRQ override on GMxBGxx (XMG APEX 17 M23)
ACPICA: Update acpixf.h for new ACPICA release 20240322
ACPICA: events/evgpeinit: don't forget to increment registered GPE count
ACPICA: Fix CXL 3.0 structure (RDPAS) in the CEDT table
ACPICA: SRAT: Add dump and compiler support for RINTC affinity structure
ACPICA: SRAT: Add RISC-V RINTC affinity structure
...
The number of updated CPU capabilities per netlink event is hard-coded to
16. On systems with more than 16 CPUs (a common case), it takes more than
one thermal netlink event to relay all the new capabilities after an HFI
interrupt. This adds unnecessary overhead to both the kernel and user space
entities.
Increase the number of CPU capabilities updated per event to 64. Any system
with 64 CPUs or less can now update all the capabilities in a single
thermal netlink event.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When processing a hardware update, HFI generates as many thermal netlink
events as needed to relay all the updated CPU capabilities to user space.
The constant HFI_MAX_THERM_NOTIFY_COUNT is the number of CPU capabilities
updated per each of those events.
Give this constant a more descriptive name.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The delay between an HFI interrupt and its corresponding thermal netlink
event has so far been hard-coded to CONFIG_HZ jiffies (1 second). This
delay is too long for hardware that generates updates every tens of
milliseconds.
The HFI driver uses a delayed workqueue to send thermal netlink events. No
subsequent events will be sent if there is pending work.
As a result, much of the information of consecutive hardware updates will
be lost if the workqueue delay is too long. User space entities may act on
obsolete data. If the delay is too short, multiple events may overwhelm
listeners.
Set the delay to 100ms to strike a balance between too many and too few
events. Use milliseconds instead of jiffies to improve readability.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The name of the constant HFI_UPDATE_INTERVAL is misleading. It is not a
periodic interval at which HFI updates are processed. It is the delay in
the processing of an HFI update after the arrival of an HFI interrupt.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Deduplicate ->read() callbacks of bin_attributes which are backed by a
simple buffer in memory:
Use the newly introduced sysfs_bin_attr_simple_read() helper instead,
either by referencing it directly or by declaring such bin_attributes
with BIN_ATTR_SIMPLE_RO() or BIN_ATTR_SIMPLE_ADMIN_RO().
Aside from a reduction of LoC, this shaves off a few bytes from vmlinux
(304 bytes on an x86_64 allyesconfig).
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Zhi Wang <zhiwang@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/92ee0a0e83a5a3f3474845db6c8575297698933a.1712410202.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Lunar Lake ACPI IDs for DPTF devices.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
psvt->limit.string can only be 8 bytes so let's use the appropriate size
macro ACPI_LIMIT_STR_MAX_LEN.
Neither psvt->limit.string or psvt_user[i].limit.string requires the
NUL-padding behavior that strncpy() provides as they have both been
filled with NUL-bytes prior to the string operation.
| memset(&psvt->limit, 0, sizeof(u64));
and
| psvt_user = kzalloc(psvt_len, GFP_KERNEL);
Let's use `strscpy` [2] due to the fact that it guarantees
NUL-termination on the destination buffer without unnecessarily
NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings # [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable and disable hardware feedback interface (HFI) when user space
handler is present. For example, enable HFI, when intel-speed-select or
Intel Low Power daemon is running and subscribing to thermal netlink
events. When user space handlers exit or remove subscription for
thermal netlink events, disable HFI.
Summary of changes:
- Register a thermal genetlink notifier
- In the notifier, process THERMAL_NOTIFY_BIND and THERMAL_NOTIFY_UNBIND
reason codes to count number of thermal event group netlink multicast
clients. If thermal netlink group has any listener enable HFI on all
packages. If there are no listener disable HFI on all packages.
- When CPU is online, instead of blindly enabling HFI, check if
the thermal netlink group has any listener. This will make sure that
HFI is not enabled by default during boot time.
- Actual processing to enable/disable matches what is done in
suspend/resume callbacks. Create two functions hfi_enable_instance()
and hfi_disable_instance(), which can be called from the netlink
notifier callback and suspend/resume callbacks.
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
