After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/thermal to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
On the way make a few whitespace changes to make indention consistent.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241019163412.304422-2-u.kleine-koenig@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Don't populate the read-only arrays on the stack at run time, instead
make them static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20241022184622.1296044-1-colin.i.king@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
On some pre-production hardware, the SoCs do not contain calibration
data for the thermal sensors. The downstream drivers provide default
values that sort of work, instead of having the thermal sensors not
work at all.
Port the default values to the upstream driver. These values are from
the ChromeOS kernels, which sadly do not cover the MT7988.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240620092306.2352606-1-wenst@chromium.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix thermal zone names for consistency with the other SoCs:
- GPU0 must be used as the first GPU item.
- SOCx deal with audio DSP, video, and infra subsystems.
The naming must be fixed "atomically" so compilation does not break.
As a result, the change is made in the dt-bindings and in the LVTS
driver within a single commit, despite the checkpatch warning.
The definitions can be safely modified here because they are used only
in the LVTS driver, which is modified accordingly, and have not yet
been included in a released kernel.
Fixes: 78c88534e5 ("dt-bindings: thermal: mediatek: Add LVTS thermal controller definition for MT8188")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/20240603-mtk-thermal-mt818x-dtsi-v7-2-8c8e3c7a3643@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix a thermal zone name for consistency with the other SoCs:
MFG contains GPU, the latter is more specific and must be used here.
The naming must be fixed "atomically" so compilation does not break.
As a result, the change is made in the dt-bindings and in the LVTS
driver within a single commit, despite the checkpatch warning.
The definition can be safely modified here because it is used only
in the LVTS driver, which is modified accordingly, and has not yet
been included in a released kernel.
Fixes: a2ca202350 ("dt-bindings: thermal: mediatek: Add LVTS thermal controller definition for MT8186")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/20240603-mtk-thermal-mt818x-dtsi-v7-1-8c8e3c7a3643@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch prevents from registering thermal entries and letting the
driver misbehave if efuse data is invalid. A device is not properly
calibrated if the golden temperature is zero.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Reviewed-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240604-mtk-thermal-calib-check-v2-1-8f258254051d@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Filtered mode is not supported on mt8188 SoC and is the source of bad
results. Move to immediate mode which provides good temperatures.
Fixes: f4745f546e ("thermal/drivers/mediatek/lvts_thermal: Add MT8188 support")
Reviewed-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Link: https://lore.kernel.org/r/20240516-mtk-thermal-mt8188-mode-fix-v2-1-40a317442c62@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In 'lvts_should_update_thresh()' and 'lvts_ctrl_start()' functions,
the parameter passed to 'lvts_for_each_valid_sensor()' macro is always
'lvts_ctrl->lvts_data->lvts_ctrl'. In other words, the array index 0
is systematically passed as 'struct lvts_ctrl_data' type item, even
when another item should be consumed instead.
Hence, the 'valid_sensor_mask' value which is selected can be wrong
because unrelated to the 'struct lvts_ctrl_data' type item that should
be used. Hence, some thermal zone can be registered for a sensor 'i'
that does not actually exist. Because of the invalid address used
as 'lvts_sensor[i].msr', this situation ends up with a crash in
'lvts_get_temp()' function, where this 'msr' pointer is passed to
'readl_poll_timeout()' function. The following message is output:
"Unable to handle kernel NULL pointer dereference at virtual
address <msr>", with <msr> = 0.
This patch fixes the issue.
Fixes: 11e6f4c314 ("thermal/drivers/mediatek/lvts_thermal: Allow early empty sensor slots")
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Reviewed-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240503-mtk-thermal-lvts-ctrl-idx-fix-v1-2-f605c50ca117@baylibre.com
In struct lvts_ctrl_data, num_lvts_sensor and cal_offset[] are not used.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240503-mtk-thermal-lvts-ctrl-idx-fix-v1-1-f605c50ca117@baylibre.com
Some systems don't always populate sensor controller slots starting
at slot 0. Use a bitmap instead of a count to indicate valid sensor
slots. Also create a pretty iterator for that.
About that iterator: it causes checkpatch to complain with "ERROR:
Macros with multiple statements should be enclosed in a do - while
loop". However this is not possible here. And many similar iterators
do exist using the same form in the tree already.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-12-nico@fluxnic.net
The golden temperature calibration value in nvram is not always the
3rd byte. A future commit will prove this assumption wrong.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-11-nico@fluxnic.net
Current code assumes calibration values are always stored contiguously
in host endian order. A future patch will prove this wrong.
Let's specify the offset for each calibration byte instead.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-5-nico@fluxnic.net
All the .hw_tshut_temp instances are initialized with the same value.
Let's remove those and use a common definition instead. If ever a
different value must be used in the future then an override parameter
could be added back.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-4-nico@fluxnic.net
Move efuse data interpretation inside lvts_golden_temp_init() alongside
the actual code retrieving wanted value.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-3-nico@fluxnic.net
Calibration values are 24-bit wide. Those values so far appear to span
only 16 bits but let's not push our luck.
Found while looking at the original Mediatek driver code.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240402032729.2736685-2-nico@fluxnic.net
In order for lvts_raw_to_temp to function properly on mt8192,
temperature coefficients for mt8192 need to be added.
Fixes: 288732242d ("thermal/drivers/mediatek/lvts_thermal: Add mt8192 support")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240416-lvts_thermal-v2-1-f8a36882cc53@chromium.org
Reading thermal sensor on mt7986 devices returns invalid temperature:
bpi-r3 ~ # cat /sys/class/thermal/thermal_zone0/temp
-274000
Fix this by adding missing members in mtk_thermal_data struct which were
used in mtk_thermal_turn_on_buffer after commit 33140e668b.
Cc: stable@vger.kernel.org
Fixes: 33140e668b ("thermal/drivers/mediatek: Control buffer enablement tweaks")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230907112018.52811-1-linux@fw-web.de
If devm_krealloc() fails, then 'efuse' is leaking.
So free it to avoid a leak.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/481d345233862d58c3c305855a93d0dbc2bbae7e.1706431063.git.christophe.jaillet@wanadoo.fr
Update LVTS calibration data documentation for mt8192 and mt8195.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[bero@baylibre.com: Fix issues pointed out by Nícolas F. R. A. Prado <nfraprado@collabora.com>]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231017190545.157282-6-bero@baylibre.com
Add LVTS Driver support for MT8192.
Co-developed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[bero@baylibre.com: cosmetic changes, rebase]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231017190545.157282-4-bero@baylibre.com
Add suspend and resume support to LVTS driver.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
[bero@baylibre.com: suspend/resume in noirq phase]
Co-developed-by: Bernhard Rosenkränzer <bero@baylibre.com>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231017190545.157282-3-bero@baylibre.com
debugfs_create_dir() function returns an error value embedded in
the pointer (PTR_ERR). Evaluate the return value using IS_ERR
rather than checking for NULL.
Signed-off-by: Minjie Du <duminjie@vivo.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230921091057.3812-1-duminjie@vivo.com
Add Support for Mediatek Filogic 880/MT7988 LVTS.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230922055020.6436-5-linux@fw-web.de
The upcoming mt7988 has different temperature coefficients so we
cannot use constants in the functions lvts_golden_temp_init,
lvts_golden_temp_init and lvts_raw_to_temp anymore.
Add a field in the lvts_ctrl pointing to the lvts_data which now
contains the soc-specific temperature coefficents.
To make the code better readable, rename static int coeff_b to
golden_temp_offset, COEFF_A to temp_factor and COEFF_B to temp_offset.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230922055020.6436-4-linux@fw-web.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811192847.3838-1-aboutphysycs@gmail.com
Currently, when a controller is configured to use filtered mode, thermal
readings are valid only about 30% of the time.
Upon testing, it was noticed that lowering any of the interval settings
resulted in an improved rate of valid data. The same was observed when
decreasing the number of samples for each sensor (which also results in
quicker measurements).
Retrying the read with a timeout longer than the time it takes to
resample (about 344us with these settings and 4 sensors) also improves
the rate.
Lower all timing settings to the minimum, configure the filtering to
single sample, and poll the measurement register for at least one period
to improve the data validity on filtered mode. With these changes in
place, out of 100000 reads, a single one failed, ie 99.999% of the data
was valid.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713154743.611870-1-nfraprado@collabora.com
Referring to platform_get_irq()'s definition, the return value has
already been checked if ret < 0, and printed via dev_err_probe().
Calling dev_err_probe() one more time outside platform_get_irq()
is obviously redundant.
Removing dev_err_probe() outside platform_get_irq() to clean up
above problem.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230802094527.988842-1-chenjiahao16@huawei.com
The documentation says "If an error occurs, ERR_PTR(-ERROR) will be
returned" but the current code checks against a NULL pointer returned.
Fix this by checking if IS_ERR().
Signed-off-by: Minjie Du <duminjie@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230713042413.2519-1-duminjie@vivo.com
Each LVTS thermal controller can have up to four sensors, each capable
of triggering its own interrupt when its measured temperature crosses
the configured threshold. The threshold for each sensor is handled
separately by the thermal framework, since each one is registered with
its own thermal zone and trips. However, the temperature thresholds are
configured on the controller, and therefore are shared between all
sensors on that controller.
When the temperature measured by the sensors is different enough to
cause the thermal framework to configure different thresholds for each
one, interrupts start triggering on sensors outside the last threshold
configured.
To address the issue, track the thresholds required by each sensor and
only actually set the highest one in the hardware, and disable
interrupts for all sensors outside the current configured range.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-7-nfraprado@collabora.com
The thermal framework might leave the low threshold unset if there
aren't any lower trip points. This leaves the register zeroed, which
translates to a very high temperature for the low threshold. The
interrupt for this threshold is then immediately triggered, and the
state machine gets stuck, preventing any other temperature monitoring
interrupts to ever trigger.
(The same happens by not setting the Cold or Hot to Normal thresholds
when using those)
Set the unused threshold to a valid low value. This value was chosen so
that for any valid golden temperature read from the efuse, when the
value is converted to raw and back again to milliCelsius, the result
doesn't underflow.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-6-nfraprado@collabora.com
Out of the many interrupts supported by the hardware, the only ones of
interest to the driver currently are:
* The temperature went over the high offset threshold, for any of the
sensors
* The temperature went below the low offset threshold, for any of the
sensors
* The temperature went over the stage3 threshold
These are the only thresholds configured by the driver through the
OFFSETH, OFFSETL, and PROTTC registers, respectively.
The current interrupt mask in LVTS_MONINT_CONF, enables many more
interrupts, including data ready on sensors for both filtered and
immediate mode. These are not only not handled by the driver, but they
are also triggered too often, causing unneeded overhead. Disable these
unnecessary interrupts.
The meaning of each bit can be seen in the comment describing
LVTS_MONINTST in the IRQ handler.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-5-nfraprado@collabora.com
There are two kinds of temperature monitoring interrupts available:
* High Offset, Low Offset
* Hot, Hot to normal, Cold
The code currently uses the hot/h2n/cold interrupts, however in a way
that doesn't work: the cold threshold is left uninitialized, which
prevents the other thresholds from ever triggering, and the h2n
interrupt is used as the lower threshold, which prevents the hot
interrupt from triggering again after the thresholds are updated by the
thermal framework, since a hot interrupt can only trigger again after
the hot to normal interrupt has been triggered.
But better yet than addressing those issues, is to use the high/low
offset interrupts instead. This way only two thresholds need to be
managed, which have a simpler state machine, making them a better match
to the thermal framework's high and low thresholds.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-4-nfraprado@collabora.com
Each controller can be configured to operate on immediate or filtered
mode. On filtered mode, the sensors are enabled by setting the
corresponding bits in MONCTL0, while on immediate mode, by setting
MSRCTL1.
Previously, the code would set MSRCTL1 for all four sensors when
configured to immediate mode, but given that the controller might not
have all four sensors connected, this would cause interrupts to trigger
for non-existent sensors. Fix this by handling the MSRCTL1 register
analogously to the MONCTL0: only enable the sensors that were declared.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-3-nfraprado@collabora.com
There is a single IRQ handler for each LVTS thermal domain, and it is
supposed to check each of its underlying controllers for the origin of
the interrupt and clear its status. However due to a typo, only the
first controller was ever being handled, which resulted in the interrupt
never being cleared when it happened on the other controllers. Add the
missing index so interrupts are handled for all controllers.
Fixes: f5f633b182 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230706153823.201943-2-nfraprado@collabora.com
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-10-frank.li@vivo.com
Register thermal zones as hwmon sensors to let userspace read
temperatures using standard hwmon interface.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230613091317.1691247-1-wenst@chromium.org
This reverts commit f05c7b7d9e.
That change was causing a regression in the generic-adc-thermal-probed
bootrr test as reported in the kernelci-results list [1].
A proper rework will take longer, so revert it for now.
[1] https://groups.io/g/kernelci-results/message/42660
Fixes: f05c7b7d9e ("thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe")
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230525121811.3360268-1-ricardo.canuelo@collabora.com
Replace of_get_address() and of_translate_address() calls with single
call to of_address_to_resource().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230319163231.226738-1-robh@kernel.org
Use devm_clk_get_enabled to do automatic resource management.
Meanwhile, remove error handling labels in the probe function and
the whole remove function.
Signed-off-by: Kang Chen <void0red@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230419020749.621257-2-void0red@hust.edu.cn
Smatch reports:
1. mtk_thermal_probe() warn: 'apmixed_base' from of_iomap() not released.
2. mtk_thermal_probe() warn: 'auxadc_base' from of_iomap() not released.
The original code forgets to release iomap resource when handling errors,
fix it by switch to devm_of_iomap.
Fixes: 89945047b1 ("thermal: mediatek: Add tsensor support for V2 thermal system")
Signed-off-by: Kang Chen <void0red@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230419020749.621257-1-void0red@hust.edu.cn
The AUXADC thermal v1 allows reading temperature range between -20°C to
150°C and any value out of this range is invalid.
Add new definitions for MT8173_TEMP_{MIN_MAX} and a new small helper
mtk_thermal_temp_is_valid() to check if new readings are in range: if
not, we tell to the API that the reading is invalid by returning
THERMAL_TEMP_INVALID.
It was chosen to introduce the helper function because, even though this
temperature range is realistically ok for all, it comes from a downstream
kernel driver for version 1, but here we also support v2 and v3 which may
may have wider constraints.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230419061146.22246-3-angelogioacchino.delregno@collabora.com
Some more testing revealed that this commit introduces a regression on some
MT8173 Chromebooks and at least on one MT6795 Sony Xperia M5 smartphone due
to the delay being apparently variable and machine specific.
Another solution would be to delay for a bit more (~70ms) but this is not
feasible for two reasons: first of all, we're adding an even bigger delay
in a probe function; second, some machines need less, some may need even
more, making the msleep at probe solution highly suboptimal.
This reverts commit 10debf8c2d.
Fixes: 10debf8c2d ("thermal/drivers/mediatek: Add delay after thermal banks initialization")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230419061146.22246-2-angelogioacchino.delregno@collabora.com
Add MT8195 AP Domain support to LVTS Driver.
Take the opportunity to update the comments to show calibration data
information related to the new domain.
[dlezcano]: Massaged a bit the changelog
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230307154524.118541-3-bchihi@baylibre.com
