This is a UHS-II version of sdhci's add_host/remove_host operation.
Any sdhci drivers which are capable of handling UHS-II cards must
call those functions instead of the corresponding sdhci's.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-9-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a UHS-II version of sdhci's set_timeout() operation.
Use sdhci_uhs2_set_timeout() to set and calculate the timeout time.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-8-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a UHS-II version of sdhci's set_power operation.
Use sdhci_uhs2_set_power() to set VDD2 for support UHS2 interface.
VDD2, as well as VDD, is handled here.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-7-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sdhci_uhs2_reset() does a UHS-II specific reset operation.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-6-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dump UHS-II specific registers, if available, in sdhci_dumpregs()
for informative/debugging use.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-5-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds sdhci-uhs2.c as a module for UHS-II support.
This is a skeleton for further development in this patch series.
This kernel configuration, CONFIG_MMC_SDHCI_UHS2, will be used
in the following commits to indicate UHS-II specific code in sdhci
controllers.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-4-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add UHS-II related definitions in sdhci.h and sdhci-uhs2.h.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241018105333.4569-3-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Embed UHS-II access/control functionality into the MMC request
processing flow.
Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Message-ID: <20241018105333.4569-2-victorshihgli@gmail.com>
[Ulf: A couple of cleanups and fixed sd_uhs2_power_off()]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GCC 13 complains about the truncated output of snprintf():
drivers/mmc/host/mmc_spi.c: In function ‘mmc_spi_response_get’:
drivers/mmc/host/mmc_spi.c:227:64: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^
drivers/mmc/host/mmc_spi.c:227:9: note: ‘snprintf’ output between 26 and 43 bytes into a destination of size 32
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
228 | cmd->opcode, maptype(cmd));
Drop it and fold the string it generates into the only place where it's
emitted - the dev_dbg() call at the end of the function.
Fixes: 15a0580ced ("mmc_spi host driver")
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241008160134.69934-1-brgl@bgdev.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There's no reason for this driver to use the OF-specific variant so
switch to using the generic device_get_match_data() helper instead.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241007114918.52066-2-brgl@bgdev.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For better readability, put all header inclusions in alphabetical order.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241007114918.52066-1-brgl@bgdev.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add hw_reset callback to support emmc hardware reset, this callback get
called from the mmc core only when "cap-mmc-hw-reset" property is
defined in the DT.
Signed-off-by: Paul Alvin <alvin.paulp@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20241007095445.19340-1-alvin.paulp@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This already returns NULL when not found. However, it can return
EPROBE_DEFER and should thus return here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://lore.kernel.org/r/20240930224919.355359-4-rosenp@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
My guess is some automated tool missed this transformation. Now looks
clearer as do what's happening. Also allows removal of struct resource.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://lore.kernel.org/r/20240930224919.355359-3-rosenp@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allows removing several gotos.
Also fixed some wrong ones.
Added dev_err_probe where EPROBE_DEFER is possible.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://lore.kernel.org/r/20240930224919.355359-2-rosenp@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch corrects several typos in comments within the mmc/host
directory. No functional changes are introduced, only comment
improvements for better readability.
Detected using codespell.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20240929093418.526901-1-yujiaoliang@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The debug message could still report success when getting the channels
was OK but configuring them failed. This actually caused a minor detour
when debugging DMA problems, so make sure the success is only reported
when the channels are really ready-to-use.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240928094454.3592-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move some part out from mmc_go_idle() into a new function called
__mmc_go_idle(), allowing it to be re-used, which is shown from a
subsequent change.
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20240913102836.6144-7-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow an additional external regulator to be controlled by an mmc host
driver, let's add support for a vqmmc2 regulator to the mmc core.
For an SD UHS-II interface the vqmmc2 regulator may correspond to the so
called vdd2 supply, as described by the SD spec. Initially, only 1.8V is
needed, hence limit the new helper function, mmc_regulator_set_vqmmc2() to
this too.
Note that, to allow for flexibility mmc host drivers need to manage the
enable/disable of the vqmmc2 regulator themselves, while the regulator is
looked up through the common mmc_regulator_get_supply().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-5-victorshihgli@gmail.com
To inform the users about SD UHS-II cards, let's extend the print at card
insertion with a "UHS-II" substring. Within this change, it seems
reasonable to convert from using "ultra high speed" into "UHS-I speed", for
the UHS-I type, as it should makes it more clear.
Note that, the new print for UHS-II cards doesn't include the actual
selected speed mode. Instead, this is going to be added from subsequent
change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-4-victorshihgli@gmail.com
The SD UHS-II interface was introduced to the SD spec v4.00 several years
ago. The interface is fundamentally different from an electrical and a
protocol point of view, comparing to the legacy SD interface.
However, the legacy SD protocol is supported through a specific transport
layer (SD-TRAN) defined in the UHS-II addendum of the spec. This allows the
SD card to be managed in a very similar way as a legacy SD card, hence a
lot of code can be re-used to support these new types of cards through the
mmc subsystem.
Moreover, an SD card that supports the UHS-II interface shall also be
backwards compatible with the legacy SD interface, which allows a UHS-II
card to be inserted into a legacy slot. As a matter of fact, this is
already supported by mmc subsystem as of today.
To prepare to add support for UHS-II, this change puts the basic foundation
in the mmc core in place, allowing it to be more easily reviewed before
subsequent changes implements the actual support.
Basically, the approach here adds a new UHS-II bus_ops type and adds a
separate initialization path for the UHS-II card. The intent is to avoid us
from sprinkling the legacy initialization path, but also to simplify
implementation of the UHS-II specific bits.
At this point, there is only one new host ops added to manage the various
ios settings needed for UHS-II. Additional host ops that are needed, are
being added from subsequent changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-3-victorshihgli@gmail.com
The current print of the bus speed mode in mmc_add_card() has grown over
the years and is now difficult to parse. Let's clean up the code and also
take the opportunity to properly announce "DDR" for eMMCs as
"high speed DDR", which is according to the eMMC spec.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20240913102836.6144-2-victorshihgli@gmail.com
hsq allows to get more in-flight requests from mmc core, which can be
prepared in advance and be issued asynchronously to the completion of
the preceding request (in atomic context). This is presumably broken
though by the mandatory CMD22 for SDUC.
We plan to make it work, but only as an improvement on top of the
initial support for SDUC.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-10-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Planning to ameliorate it in the very near future.
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-9-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ACMD22 is used to verify the previously write operation. Normally, it
returns the number of written sectors as u32. SDUC, however, returns it
as u64. This is not a superfluous requirement, because SDUC writes may
exceeds 2TB. For Linux mmc however, the previously write operation
could not be more than the block layer limits, thus we make room for a
u64 and cast the returning value to u32.
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-8-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Stephen Rothwell: Fix build error when moving to new rc from Linus's tree]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Preparing for SDUC, Allow the erase address to be larger beyond a 32 bit
address.
Tested-by: Ricky WU <ricky_wu@realtek.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-6-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For open-ended read/write - just send CMD22 before issuing the command.
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-5-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDUC spec expects CMD22 to get squeezed between CMD23 and the
read/write command, e.g. CMD23->CMD22->CMD18 and CMD23->CMD22->CMD25.
At this early stage of adoption, we want to avoid an amid stream of
fixes & quirks of bogus hw, that tends to apply extra logic specifically
around auto-cmd12 & auto-cmd23.
Let's leave close-ended out for now, and re-consider this should those
cards become ubiquitous, if any.
It also means that BLK_FEAT_FUA will not be used for I/O, but instead we
will rely on BLK_FEAT_WRITE_CACHE.
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-4-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDUC memory addressing spans beyond 2TB and up to 128TB. Therefore, 38
bits are required to access the entire memory space of all sectors.
Those extra 6 bits are to be carried by CMD22 prior of sending
read/write/erase commands: CMD17, CMD18, CMD24, CMD25, CMD32, and CMD33.
CMD22 will carry the higher order 6 bits, and must precedes any of the
above commands even if it targets sector < 2TB.
No error related to address or length is indicated in CMD22 but rather
in the read/write command itself.
Tested-by: Ricky WU <ricky_wu@realtek.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-3-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ultra Capacity SD cards (SDUC) was already introduced in SD7.0. Those
cards support capacity larger than 2TB and up to including 128TB.
ACMD41 was extended to support the host-card handshake during
initialization. The card expects that the HCS & HO2T bits to be set in
the command argument, and sets the applicable bits in the R3 returned
response. On the contrary, if a SDUC card is inserted to a
non-supporting host, it will never respond to this ACMD41 until
eventually, the host will timed out and give up.
Also, add SD CSD version 3.0 - designated for SDUC, and properly parse
the csd register as the c_size field got expanded to 28 bits.
Do not enable SDUC for now - leave it to the last patch in the series.
Tested-by: Ricky WU <ricky_wu@realtek.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20241006051148.160278-2-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mmc to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240927145832.754697-2-u.kleine-koenig@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable SDHCI_QUIRK_NO_LED for i.MX7ULP, i.MX8MM, i.MX8QXP and
i.MXRT1050. Even there is LCTL register bit, there is no IOMUX PAD
for it. So there is no sense to enable LED for SDHCI for these SoCs.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240923062016.1165868-1-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_start_signal_voltage_switch function sets
V1P8_SIGNAL_ENA by default after switching to 1v8 signaling.
V1P8_SIGNAL_ENA determines whether to launch cmd/data on neg
edge or pos edge of clock.
Due to some eMMC and SD failures seen across am62x platform,
do not set V1P8_SIGNAL_ENA by default, only enable the bit
for devices that require this bit in order to switch to 1v8
voltage for uhs modes.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240913185403.1339115-1-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GIGASTONE Gaming Plus microSD cards manufactured on 02/2022 report that
they support poweroff notification and cache, but they are not working
correctly.
Flush Cache bit never gets cleared in sd_flush_cache() and Poweroff
Notification Ready bit also never gets set to 1 within 1 second from the
end of busy of CMD49 in sd_poweroff_notify().
This leads to I/O error and runtime PM error state.
I observed that the same card manufactured on 01/2024 works as expected.
This problem seems similar to the Kingston cards fixed with
commit c467c8f081 ("mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston
Canvas Go Plus from 11/2019") and should be handled using quirks.
CID for the problematic card is here.
12345641535443002000000145016200
Manufacturer ID is 0x12 and defined as CID_MANFID_GIGASTONE as of now,
but would like comments on what naming is appropriate because MID list
is not public and not sure it's right.
Signed-off-by: Keita Aihara <keita.aihara@sony.com>
Link: https://lore.kernel.org/r/20240913094417.GA4191647@sony.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Prevent splat from warning when setting maximum DMA segment
MMC host:
- mvsdio: Drop sg_miter support for PIO as it didn't work
- sdhci-of-dwcmshc: Prevent stale interrupt for the T-Head 1520 variant
-----BEGIN PGP SIGNATURE-----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=dlxF
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Prevent splat from warning when setting maximum DMA segment
MMC host:
- mvsdio: Drop sg_miter support for PIO as it didn't work
- sdhci-of-dwcmshc: Prevent stale interrupt for the T-Head 1520
variant"
* tag 'mmc-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-of-dwcmshc: Prevent stale command interrupt handling
Revert "mmc: mvsdio: Use sg_miter for PIO"
mmc: core: Only set maximum DMA segment size if DMA is supported
While working with the T-Head 1520 LicheePi4A SoC, certain conditions
arose that allowed me to reproduce a race issue in the sdhci code.
To reproduce the bug, you need to enable the sdio1 controller in the
device tree file
`arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi` as follows:
&sdio1 {
bus-width = <4>;
max-frequency = <100000000>;
no-sd;
no-mmc;
broken-cd;
cap-sd-highspeed;
post-power-on-delay-ms = <50>;
status = "okay";
wakeup-source;
keep-power-in-suspend;
};
When resetting the SoC using the reset button, the following messages
appear in the dmesg log:
[ 8.164898] mmc2: Got command interrupt 0x00000001 even though no
command operation was in progress.
[ 8.174054] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 8.180503] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00000005
[ 8.186950] mmc2: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 8.193395] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 8.199841] mmc2: sdhci: Present: 0x03da0000 | Host ctl: 0x00000000
[ 8.206287] mmc2: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
[ 8.212733] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x0000decf
[ 8.219178] mmc2: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 8.225622] mmc2: sdhci: Int enab: 0x00ff1003 | Sig enab: 0x00ff1003
[ 8.232068] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[ 8.238513] mmc2: sdhci: Caps: 0x3f69c881 | Caps_1: 0x08008177
[ 8.244959] mmc2: sdhci: Cmd: 0x00000502 | Max curr: 0x00191919
[ 8.254115] mmc2: sdhci: Resp[0]: 0x00001009 | Resp[1]: 0x00000000
[ 8.260561] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 8.267005] mmc2: sdhci: Host ctl2: 0x00001000
[ 8.271453] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr:
0x0000000000000000
[ 8.278594] mmc2: sdhci: ============================================
I also enabled some traces to better understand the problem:
kworker/3:1-62 [003] ..... 8.163538: mmc_request_start:
mmc2: start struct mmc_request[000000000d30cc0c]: cmd_opcode=5
cmd_arg=0x0 cmd_flags=0x2e1 cmd_retries=0 stop_opcode=0 stop_arg=0x0
stop_flags=0x0 stop_retries=0 sbc_opcode=0 sbc_arg=0x0 sbc_flags=0x0
sbc_retires=0 blocks=0 block_size=0 blk_addr=0 data_flags=0x0 tag=0
can_retune=0 doing_retune=0 retune_now=0 need_retune=0 hold_retune=1
retune_period=0
<idle>-0 [000] d.h2. 8.164816: sdhci_cmd_irq:
hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x10000
intmask_p=0x18000
irq/24-mmc2-96 [000] ..... 8.164840: sdhci_thread_irq:
msg=
irq/24-mmc2-96 [000] d.h2. 8.164896: sdhci_cmd_irq:
hw_name=ffe70a0000.mmc quirks=0x2008008 quirks2=0x8 intmask=0x1
intmask_p=0x1
irq/24-mmc2-96 [000] ..... 8.285142: mmc_request_done:
mmc2: end struct mmc_request[000000000d30cc0c]: cmd_opcode=5
cmd_err=-110 cmd_resp=0x0 0x0 0x0 0x0 cmd_retries=0 stop_opcode=0
stop_err=0 stop_resp=0x0 0x0 0x0 0x0 stop_retries=0 sbc_opcode=0
sbc_err=0 sbc_resp=0x0 0x0 0x0 0x0 sbc_retries=0 bytes_xfered=0
data_err=0 tag=0 can_retune=0 doing_retune=0 retune_now=0 need_retune=0
hold_retune=1 retune_period=0
Here's what happens: the __mmc_start_request function is called with
opcode 5. Since the power to the Wi-Fi card, which resides on this SDIO
bus, is initially off after the reset, an interrupt SDHCI_INT_TIMEOUT is
triggered. Immediately after that, a second interrupt SDHCI_INT_RESPONSE
is triggered. Depending on the exact timing, these conditions can
trigger the following race problem:
1) The sdhci_cmd_irq top half handles the command as an error. It sets
host->cmd to NULL and host->pending_reset to true.
2) The sdhci_thread_irq bottom half is scheduled next and executes faster
than the second interrupt handler for SDHCI_INT_RESPONSE. It clears
host->pending_reset before the SDHCI_INT_RESPONSE handler runs.
3) The pending interrupt SDHCI_INT_RESPONSE handler gets called, triggering
a code path that prints: "mmc2: Got command interrupt 0x00000001 even
though no command operation was in progress."
To solve this issue, we need to clear pending interrupts when resetting
host->pending_reset. This ensures that after sdhci_threaded_irq restores
interrupts, there are no pending stale interrupts.
The behavior observed here is non-compliant with the SDHCI standard.
Place the code in the sdhci-of-dwcmshc driver to account for a
hardware-specific quirk instead of the core SDHCI code.
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 43658a542e ("mmc: sdhci-of-dwcmshc: Add support for T-Head TH1520")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20241008100327.4108895-1-m.wilczynski@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 2761822c00.
When testing on real hardware the patch does not work.
Revert, try to acquire real hardware, and retry.
These systems typically don't have highmem anyway so the
impact is likely zero.
Cc: stable@vger.kernel.org
Reported-by: Charlie <g4sra@protonmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240927-kirkwood-mmc-regression-v1-1-2e55bbbb7b19@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since upstream commit 334304ac2b ("dma-mapping: don't return errors
from dma_set_max_seg_size") calling dma_set_max_seg_size() on a device
not supporting DMA results in a warning traceback. This is seen when
booting the sifive_u machine from SD. The underlying SPI controller
(sifive,spi0 compatible) explicitly sets dma_mask to NULL.
Avoid the backtrace by only calling dma_set_max_seg_size() if DMA is
supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 334304ac2b ("dma-mapping: don't return errors from dma_set_max_seg_size")
Link: https://lore.kernel.org/r/20240924210123.2288529-1-linux@roeck-us.net
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- support DMA zones for arm64 systems where memory starts at > 4GB
(Baruch Siach, Catalin Marinas)
- support direct calls into dma-iommu and thus obsolete dma_map_ops for
many common configurations (Leon Romanovsky)
- add DMA-API tracing (Sean Anderson)
- remove the not very useful return value from various dma_set_* APIs
(Christoph Hellwig)
- misc cleanups and minor optimizations (Chen Y, Yosry Ahmed,
Christoph Hellwig)
-----BEGIN PGP SIGNATURE-----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=DZVc
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.12-2024-09-19' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- support DMA zones for arm64 systems where memory starts at > 4GB
(Baruch Siach, Catalin Marinas)
- support direct calls into dma-iommu and thus obsolete dma_map_ops for
many common configurations (Leon Romanovsky)
- add DMA-API tracing (Sean Anderson)
- remove the not very useful return value from various dma_set_* APIs
(Christoph Hellwig)
- misc cleanups and minor optimizations (Chen Y, Yosry Ahmed, Christoph
Hellwig)
* tag 'dma-mapping-6.12-2024-09-19' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reflow dma_supported
dma-mapping: reliably inform about DMA support for IOMMU
dma-mapping: add tracing for dma-mapping API calls
dma-mapping: use IOMMU DMA calls for common alloc/free page calls
dma-direct: optimize page freeing when it is not addressable
dma-mapping: clearly mark DMA ops as an architecture feature
vdpa_sim: don't select DMA_OPS
arm64: mm: keep low RAM dma zone
dma-mapping: don't return errors from dma_set_max_seg_size
dma-mapping: don't return errors from dma_set_seg_boundary
dma-mapping: don't return errors from dma_set_min_align_mask
scsi: check that busses support the DMA API before setting dma parameters
arm64: mm: fix DMA zone when dma-ranges is missing
dma-mapping: direct calls for dma-iommu
dma-mapping: call ->unmap_page and ->unmap_sg unconditionally
arm64: support DMA zone above 4GB
dma-mapping: replace zone_dma_bits by zone_dma_limit
dma-mapping: use bit masking to check VM_DMA_COHERENT
In case vmmc or vqmmc regulator is not available yet, use dev_err_probe
in order to set a deferred probe reason. This is a helpful hint in
/sys/kernel/debug/devices_deferred
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240911090910.3060749-1-alexander.stein@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add debug prints to tuning algorithm for debugging.
Also add error print if we fail tuning.
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240904232512.830778-3-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add retry tuning up to 10 times if we fail to find
a failing region or no passing itapdly. This is
necessary since some eMMC has been observed to never
find a failing itapdly on the first couple of tuning
iterations, but eventually does. Keep count of current
tuning iteration using tuning_loop. It has been observed
that the tuning algorithm does not need to loop more
than 10 times before finding a failing itapdly.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240904232512.830778-2-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Prevent build error when CONFIG_RPMB=m and CONFIG_MMC_BLOCK=y by adding
a dependency to CONFIG_RPMB for CONFIG_MMC_BLOCK block so the RPMB
subsystem always is reachable if configured. This means that
CONFIG_MMC_BLOCK automatically becomes compiled as a module if
CONFIG_RPMB is compiled as a module. If CONFIG_RPMB isn't configured or
is configured as built-in, CONFIG_MMC_BLOCK will remain unchanged.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409021448.RSvcBPzt-lkp@intel.com/
Fixes: 7852028a35 ("mmc: block: register RPMB partition with the RPMB subsystem")
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240902151231.3705204-1-jens.wiklander@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The UNSTUFF_BITS macro, which is defined in both drivers/mmc/core/mmc.c
and drivers/mmc/core/sd.c, has been converted to an inline function to
improve readability, maintainability, and type safety.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240902123331.3566447-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
simple_strtoul() is obsolete and lacks proper error handling, making it
unsafe for converting strings to unsigned long values. Replace it with
kstrtoul(), which provides robust error checking and better safety.
This change improves the reliability of the string-to-integer conversion
and aligns with current kernel coding standards. Error handling is added
to catch conversion failures, returning -EINVAL when input is invalid.
Issue reported by checkpatch:
- WARNING: simple_strtoul is obsolete, use kstrtoul instead
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
Link: https://lore.kernel.org/r/20240901182244.45543-1-riyandhiman14@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
