The GPU PLL0 is not a fixed PLL and the rate can be set on it:
this is necessary especially on boards which bootloader is setting
a very low rate on this PLL before booting Linux, which would be
unsuitable for postdividing to reach the maximum allowed Adreno GPU
frequency of 710MHz (or, actually, even 670MHz..) on this SoC.
To allow setting rates on the GPU PLL0, also define VCO boundaries
and set the CLK_SET_RATE_PARENT flag to the GPU PLL0 postdivider.
With this change, the Adreno GPU is now able to scale through all
the available frequencies.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-12-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The GPU GX GDSC has GPU_GX_BCR reset and gfx3d_clk CXC, as stated
on downstream kernels (and as verified upstream, because otherwise
random lockups happen).
Also, add PWRSTS_RET and NO_RET_PERIPH: also as found downstream,
and also as verified here, to avoid GPU related lockups it is
necessary to force retain mem, but *not* peripheral when enabling
this GDSC (and, of course, the inverse on disablement).
With this change, the GPU finally works flawlessly on my four
different MSM8998 devices from two different manufacturers.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-11-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In some rare occasions, we want to only set the RETAIN_MEM bit, but
not the RETAIN_PERIPH one: this is seen on at least SDM630/636/660's
GPU-GX GDSC, where unsetting and setting back the RETAIN_PERIPH bit
will generate chaos and panics during GPU suspend time (mainly, the
chaos is unaligned access).
For this reason, introduce a new NO_RET_PERIPH flag to the GDSC
driver to address this corner case.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210113183817.447866-8-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a basic driver for the MPLL block found in MStar/SigmaStar
ARMv7 SoCs.
Currently this driver is only good for calculating the rates of it's
outputs and the actual configuration must be done before the kernel
boots. Usually this is done even before u-boot starts.
This driver targets the MPLL block found in the MSC313/MSC313E but
there is no documentation this chip so the register descriptions for
the another MStar chip the MST786 were used as they seem to match.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-5-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a devm helper for clk_hw_register_fixed_factor() so that drivers that internally
register fixed factor clocks for things like dividers don't need to manually unregister
them on remove or if probe fails.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-4-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
out the correct rate to use. This fixes displays running 4k@60Hz and
some other resolutions that haven't been exercised and fully understood
until now.
-----BEGIN PGP SIGNATURE-----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=jPmu
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One small fix for the Allwinner clk driver so that display clks figure
out the correct rate to use.
This fixes displays running 4k@60Hz and some other resolutions that
haven't been exercised and fully understood until now"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: mp: fix parent rate change flag check
Add support for Intel's eASIC N5X platform. The clock manager driver for
the N5X is very similar to the Agilex platform, we can re-use most of
the Agilex clock driver.
This patch makes the necessary changes for the driver to differentiate
between the Agilex and the N5X platforms.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20210212143059.478554-2-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The bd718x7 only needs a regmap from parent device. This can be
obtained by call to dev_get_regmap. Do not require parent to
populate the driver data for this.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210105123028.GA3409663@localhost.localdomain
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Starting from A2, the A-PLL calculation has changed. Use the
existing formula for A0/A1 and the new formula for A2 onwards.
Fixes: d3d04f6c330a ("clk: Add support for AST2600 SoC")
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20210119061715.6043-1-ryan_chen@aspeedtech.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Recalling NVM data into RAM during probe() initiates a re-calibration of
the clock. If the clock is already in-use, the recall operation can cause
a glitch on the frequency out. At power on, the factory data are loaded
from NVM into RAM by default. If the clock frequency has been changed
since power on, the recall operation can be used to re-initialize the clock
to factory setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Link: https://lore.kernel.org/r/1612496104-3437-3-git-send-email-saeed.nowshadi@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are two registers which can set the load capacitance for
XTAL1 and XTAL2. These are optional registers when using an
external crystal. Parse the device tree and set the
corresponding registers accordingly.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210207185140.3653350-2-aford173@gmail.com
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/zynq/clkc.c: In function ‘zynq_clk_register_fclk’:
drivers/clk/zynq/clkc.c:106:14: warning: variable ‘clk’ set but not used [-Wunused-but-set-variable]
drivers/clk/zynq/clkc.c: In function ‘zynq_clk_register_periph_clk’:
drivers/clk/zynq/clkc.c:179:14: warning: variable ‘clk’ set but not used [-Wunused-but-set-variable]
drivers/clk/zynq/clkc.c: In function ‘zynq_clk_setup’:
drivers/clk/zynq/clkc.c:220:14: warning: variable ‘clk’ set but not used [-Wunused-but-set-variable]
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-21-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Also demote non-worthy header to standard comment block.
Fixes the following W=1 kernel build warning(s):
drivers/clk/versatile/clk-icst.c:53: warning: Function parameter or member 'map' not described in 'clk_icst'
drivers/clk/versatile/clk-icst.c:53: warning: Function parameter or member 'vcoreg_off' not described in 'clk_icst'
drivers/clk/versatile/clk-icst.c:53: warning: Function parameter or member 'lockreg_off' not described in 'clk_icst'
drivers/clk/versatile/clk-icst.c:435: warning: cannot understand function prototype: 'const struct icst_params icst525_apcp_cm_params = '
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-20-lee.jones@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/gate.c:67: warning: Function parameter or member 'hw' not described in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
drivers/clk/ti/gate.c:67: warning: Excess function parameter 'clk' description in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-17-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll.c:163: warning: Function parameter or member 'user' not described in '_register_dpll'
drivers/clk/ti/dpll.c:163: warning: Excess function parameter 'hw' description in '_register_dpll'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-16-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clockdomain.c:107: warning: Function parameter or member 'hw' not described in 'omap2_init_clk_clkdm'
drivers/clk/ti/clockdomain.c:107: warning: Excess function parameter 'clk' description in 'omap2_init_clk_clkdm'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-14-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/st/clkgen-fsyn.c:186: warning: Function parameter or member 'data' not described in 'st_clk_quadfs_pll'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'regs_base' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'lock' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'data' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'chan' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'md' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'pe' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'sdiv' not described in 'st_clk_quadfs_fsynth'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Stephen Gallimore <stephen.gallimore@st.com>
Cc: Pankaj Dev <pankaj.dev@st.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-13-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
And remove an incorrect entry.
Fixes the following W=1 kernel build warning(s):
drivers/clk/st/clkgen-pll.c:142: warning: cannot understand function prototype: 'struct clkgen_pll '
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Stephen Gallimore <stephen.gallimore@st.com>
Cc: Pankaj Dev <pankaj.dev@st.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-12-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Not much effort has been put into this one.
Demote it for the time being at least.
Fixes the following W=1 kernel build warning(s):
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_state_reg' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'divider_mask' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'cluster_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'force_mask' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'divider_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'divider_ratio' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_state_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_state_cluster_offset' not described in 'cpu_dfs_regs'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Omri Itach <omrii@marvell.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-10-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/socfpga/clk-pll-a10.c: In function ‘__socfpga_pll_init’:
drivers/clk/socfpga/clk-pll-a10.c:76:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-9-lee.jones@linaro.org
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/socfpga/clk-pll.c: In function ‘__socfpga_pll_init’:
drivers/clk/socfpga/clk-pll.c:83:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-8-lee.jones@linaro.org
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/sifive/fu540-prci.h:16:35: warning: ‘prci_clk_fu540’ defined but not used [-Wunused-const-variable=]
drivers/clk/sifive/fu540-prci.h:16:35: warning: ‘prci_clk_fu540’ defined but not used [-Wunused-const-variable=]
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Pragnesh Patel <Pragnesh.patel@sifive.com>
Cc: Zong Li <zong.li@sifive.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-7-lee.jones@linaro.org
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/zynqmp/divider.c:46: warning: Function parameter or member 'max_div' not described in 'zynqmp_clk_divider'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Rajan Vaja <rajan.vaja@xilinx.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-22-lee.jones@linaro.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/spear/spear1310_clock.c:385:13: warning: no previous prototype for ‘spear1310_clk_init’ [-Wmissing-prototypes]
drivers/clk/spear/spear1340_clock.c:442:13: warning: no previous prototype for ‘spear1340_clk_init’ [-Wmissing-prototypes]
Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-20-lee.jones@linaro.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/clk-rpm.c:453:29: warning: ‘clk_rpm_branch_ops’ defined but not used [-Wunused-const-variable=]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-19-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/clk-xgene.c:229: warning: Function parameter or member 'mask' not described in 'xgene_clk_pmd'
drivers/clk/clk-xgene.c:229: warning: Function parameter or member 'flags' not described in 'xgene_clk_pmd'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Loc Ho <lho@apm.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-18-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/mmcc-msm8974.c:85:27: warning: ‘mmcc_xo_mmpll0_1_2_gpll0’ defined but not used [-Wunused-const-variable=]
drivers/clk/qcom/mmcc-msm8974.c:77:32: warning: ‘mmcc_xo_mmpll0_1_2_gpll0_map’ defined but not used [-Wunused-const-variable=]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-17-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/clk-npcm7xx.c:438:43: warning: ‘npcm7xx_gates’ defined but not used [-Wunused-const-variable=]
drivers/clk/clk-npcm7xx.c:365:48: warning: ‘npcm7xx_divs_fx’ defined but not used [-Wunused-const-variable=]
Cc: Avi Fishman <avifishman70@gmail.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Tali Perry <tali.perry1@gmail.com>
Cc: Patrick Venture <venture@google.com>
Cc: Nancy Yuen <yuenn@google.com>
Cc: Benjamin Fair <benjaminfair@google.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Nuvoton Technologies <tali.perry@nuvoton.com>
Cc: openbmc@lists.ozlabs.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-16-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/clk-fixed-mmio.c:62: warning: Function parameter or member 'pdev' not described in 'of_fixed_mmio_clk_probe'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jan Kotas <jank@cadence.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-15-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/gcc-ipq4019.c: In function ‘clk_cpu_div_set_rate’:
drivers/clk/qcom/gcc-ipq4019.c:1279:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-14-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-11-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/tegra/cvb.c:106: warning: Function parameter or member 'align' not described in 'tegra_cvb_add_opp_table'
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-10-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/tegra/clk-tegra30.c: In function ‘tegra30_enable_cpu_clock’:
drivers/clk/tegra/clk-tegra30.c:1107:15: warning: variable ‘reg’ set but not used [-Wunused-but-set-variable]
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-8-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/clk-regmap.c:97: warning: Function parameter or member 'dev' not described in 'devm_clk_register_regmap'
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-5-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'hw' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'parent_rate' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Excess function parameter 'clk' description in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:437: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:437: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:479: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:479: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'hw' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'parent_rate' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Excess function parameter 'clk' description in 'omap3_clkoutx2_recalc'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-4-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'hw' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'parent_rate' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Excess function parameter 'clk' description in 'omap2_dpll_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-3-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'name' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'parent' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'pll_ctrl' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'pll_status' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'lock_index' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'lock' not described in 'clk_register_zynq_pll'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-2-lee.jones@linaro.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These are all "early clocks" that require initialization just at
of_clk_init() time. Use CLK_OF_DECLARE() to declare them.
This also fixes a problem that was spotted when fw_devlink was
set to 'on' by default: the boards failed to boot. The reason is
that CLK_OF_DECLARE_DRIVER() clears the OF_POPULATED and causes
the consumers of the clock to be postponed by fw_devlink until
the second initialization routine of the clock has been completed.
One of the consumers of the clock is the timer, which is used as a
clocksource, and needs the clock initialized early. Postponing the
timers caused the fail at boot.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210203154332.470587-1-tudor.ambarus@microchip.com
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This allows fw_devlink to recognize clock provider drivers that don't
use the device-driver model to initialize the device. fw_devlink will
use this information to make sure consumers of such clock providers
aren't indefinitely blocked from probing, waiting for the power domain
device to appear and bind to a driver.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210205222644.2357303-9-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On AXG platforms HHI_MIPI_CNTL0 is part of the MIPI/PCIe analog PHY
region and is not related to clock one and can be removed from it.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The mux clocks don't always correctly take the new parent into account
when the parent is updated while the clock is disabled. Set the update
bit when enabling the clock to force an update of the mux.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210125170819.26130-3-laurent.pinchart@ideasonboard.com
Reviewed-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If MT8183 SoC support is enabled, almost all machines will use topckgen,
apmixedsys, infracfg, mcucfg and subsystem clocks, so it feels wrong to
require each one to select that symbols manually.
Instead, enable it whenever COMMON_CLK_MT8183_* is disabled as
a simplification. This would add few KB in the kernel image size but
will make the life a bit easier to the users, anyway you'll need to probably
enable all of them if you want to have proper support for that SoC.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210203105423.682960-1-enric.balletbo@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-5-arnd@kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-4-arnd@kernel.org
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-3-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-2-arnd@kernel.org
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The xlnx_vcu driver is actually a clock controller driver which provides
clocks that can be used by a driver for the encoder/decoder units. There
is no reason to keep this driver in soc. Move the driver to clk.
NOTE: The register mapping actually contains registers for AXI
performance monitoring, but these are not used by the driver.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210121071659.1226489-16-m.tretter@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
