Add to each mode supported by the sensor the ideal pixel rate, as
defined by Table 2.1 in the chip manual.
The ideal pixel rate will be used to compute the MIPI CSI-2 clock tree.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support of 1X16 serial pixel formats in order to support
CSI-2 camera sensor exposing 1x16 pixel formats only.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Expose RGB & YUV 1X16 serial pixel format variants to comply
with CSI-2 camera sensor pixel formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Those two formats were missing in the list of supported MBUS
formats.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The s_stream callback had several issues:
- If pm_runtime_get_sync() fails, the usage_count is not put.
- The sensor wasn't suspended if s_stream(subdev, 1) failed.
Fix this.
Fixes: ("media: i2c: Add pm_runtime support to ov7251")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A83T supports MIPI CSI-2 with a composite controller, covering
both the protocol logic and the D-PHY implementation. This controller
seems to be found on the A83T only and probably was abandoned since.
This implementation splits the protocol and D-PHY registers and
uses the PHY framework internally. The D-PHY is not registered as a
standalone PHY driver since it cannot be used with any other
controller.
There are a few notable points about the controller:
- The initialisation sequence involes writing specific magic init
values that do not seem to make any particular sense given the
concerned register fields;
- Interrupts appear to be hitting regardless of the interrupt mask
registers, which can cause a serious flood when transmission errors
occur.
Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.
This work is based on the first version of the driver submitted by
Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP.
This version integrates MIPI CSI-2 support as a standalone V4L2 subdev
instead of merging it in the sun6i-csi driver.
It was tested on a Banana Pi M3 board with an OV8865 sensor in a 4-lane
configuration.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This introduces YAML bindings documentation for the Allwinner A83T
MIPI CSI-2 controller.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add myself as maintainer of the Allwinner A31 MIPI CSI-2 bridge media
driver.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A31 MIPI CSI-2 controller is a dedicated MIPI CSI-2 bridge
found on Allwinner SoCs such as the A31 and V3/V3s.
It is a standalone block, connected to the CSI controller on one side
and to the MIPI D-PHY block on the other. It has a dedicated address
space, interrupt line and clock.
It is represented as a V4L2 subdev to the CSI controller and takes a
MIPI CSI-2 sensor as its own subdev, all using the fwnode graph and
media controller API.
Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This introduces YAML bindings documentation for the Allwinner A31 MIPI
CSI-2 controller.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A31 CSI controller supports two distinct input interfaces:
parallel and an external MIPI CSI-2 bridge. The parallel interface
is often connected to a set of hardware pins while the MIPI CSI-2
bridge is an internal FIFO-ish link. As a result, these two inputs
are distinguished as two different ports.
Note that only one of the two may be present on a controller instance.
For example, the V3s has one controller dedicated to MIPI-CSI2 and one
dedicated to parallel.
Update the binding with an explicit ports node that holds two distinct
port nodes: one for parallel input and one for MIPI CSI-2.
This is backward-compatible with the single-port approach that was
previously taken for representing the parallel interface port, which
stays enumerated as fwnode port 0.
Note that additional ports may be added in the future, especially to
support feeding the CSI controller's output to the ISP.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The RK3566 and RK3568 SoCs come with a small Hantro instance which is
solely dedicated to encoding. This patch adds the necessary structs to
the Hantro driver to allow the JPEG encoder of it to function.
Through some sleuthing through the vendor's MPP source code and after
closer inspection of the TRM, it was determined that the hardware likely
supports VP8 and H.264 as well.
Tested with the following GStreamer command:
gst-launch-1.0 videotestsrc ! v4l2jpegenc ! matroskamux ! \
filesink location=foo.mkv
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The RK3568 and RK3566 have a Hantro VPU node solely dedicated to
encoding. This patch adds a new binding to describe it, as it
does not really fit the rockchip-vpu binding, since there is no
decoder.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In reset vpu core, driver will wait for a response event,
but if there are still some events unhandled,
they will be handled first, driver may acquire core lock for that.
So if we do reset in core lock, it may led to reset timeout.
Fixes: 9f599f351e86a ("media: amphion: add vpu core driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The chroma order of P010 is `CbCr`,
match with the descriptions in `include/uapi/linux/videodev2.h` and the
documentation.
Fixes: 5374d8fb75f3 ("media: Add P010 video format")
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace supportedn with supported\n , i.e. add the missing backslash.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The mdp_ipi_comm structure defines a command that is either
PROCESS (start processing) or DEINIT (destroy instance); we
are using this one to send PROCESS or DEINIT commands from Linux
to an MDP instance through a VPU write but, while the first wants
us to stay 4-bytes aligned, the VPU instead requires an 8-bytes
data alignment.
Keeping in mind that these commands are executed immediately
after sending them (hence not chained with others before the
VPU/MDP "actually" start executing), it is fine to simply add
a padding of 4 bytes to this structure: this keeps the same
performance as before, as we're still stack-allocating it,
while avoiding hackery inside of mtk-vpu to ensure alignment
bringing a definitely bigger performance impact.
Fixes: c8eb2d7e8202 ("[media] media: Add Mediatek MDP Driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Reviewed-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/media/usb/pvrusb2/pvrusb2-hdw.c
line - 5044
But now it's a a chicken and egg problem...) */
changed to:
But now it's a chicken and egg problem...) */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/media/platform/ti/cal/cal-camerarx.c
line - 308
* DRA80xM TRMs have a a slightly simplified sequence.
changed to:
* DRA80xM TRMs have a slightly simplified sequence.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'is' in the comments that need to be dropped
file - drivers/media/usb/gspca/spca501.c
line - 491
* This is is for the 3com HomeConnect Lite which is spca501a based.
changed to:
* This is for the 3com HomeConnect Lite which is spca501a based.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove the repeated word 'and' from comments
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are a few cases where code is harder than needed to read.
Improve those by:
- dropping unnecessary castings (see note below)
- use PTR_ALING() to be more explicit on what's going on there
- use proper definitions instead of hard coded values
Note, dropping castings will allow to perform an additional check
that type is not changed from void * to something else, e.g. u64,
which may very well break the bitmap APIs.
Link: https://lore.kernel.org/linux-media/20220209182521.55632-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Here we introduce a new fault injection for SSR trigger.
To trigger the SSR:
echo 100 > /sys/kernel/debug/venus/fail_ssr/probability
echo 1 > /sys/kernel/debug/venus/fail_ssr/times
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix build error when VIDEO_ISL7998X=y and V4L2_FWNODE=m
by selecting V4L2_FWNODE.
microblaze-linux-ld: drivers/media/i2c/isl7998x.o: in function `isl7998x_probe':
(.text+0x8f4): undefined reference to `v4l2_fwnode_endpoint_parse'
Cc: stable@vger.kernel.org # 5.18 and above
Fixes: 51ef2be546e2 ("media: i2c: isl7998x: Add driver for Intersil ISL7998x")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media driver supports constant bitrate mode only.
The supported rate control mode is reported through querymenu() and
s_ctrl() fails if non constant bitrate mode (e.g. VBR) is requested.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
file: ./drivers/staging/media/av7110/av7110.c
line: 2367
* reset with with MASK_31 to MC1
changed to
* reset with MASK_31 to MC1
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
file: drivers/media/pci/saa7164/saa7164-api.c
line: 804
/* Assumption: Hauppauge eeprom is at 0xa0 on on bus 0 */
changed to
/* Assumption: Hauppauge eeprom is at 0xa0 on bus 0 */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
According to subdev_bitmap bit value to open hardware power, need to
set subdev_bitmap value for non subdev architecture.
Fixes: c05bada35f01 ("media: mtk-vcodec: Add to support multi hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
video_device_alloc() allocates memory for vdev,
when video_register_device() fails, it doesn't release the memory and
leads to memory leak, call video_device_release() to fix this.
Fixes: 704a84ccdbf1 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In function mxc_jpeg_probe(), when devm_clk_get() fail, the return value
will be unexpected, and it should be the devm_clk_get's error code.
Fixes: 4c2e5156d9fa6 ("media: imx-jpeg: Add pm-runtime support for imx-jpeg")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jian Zhang <zhangjian210@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
I have been working on mediatek driver development for a very long time,
and sent many patches to change the driver architecture. Add myself as
co-maintainer for mediatek vcodec driver.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The stateless decoder API does not specify the usage of SOURCE_CHANGE
and EOF events. These events are used by stateful decoders to signal
changes in the bitstream. They do not make sense for stateless decoders.
Do not handle subscription for these two types of events for stateless
decoder instances. This fixes the last v4l2-compliance error:
Control ioctls:
fail: v4l2-test-controls.cpp(946): have_source_change || have_eos
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Fixes: 8cdc3794b2e3 ("media: mtk-vcodec: vdec: support stateless API")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The commit in Fixes: is incomplete. It has moved some code in the probe but
not all error handling paths have been updated.
Now, if request_irq() fails, we must release some resources.
Fixes: c8946454ed96 ("media: tw686x: Register the irq at the end of probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fill in 10, 12, 14 bit Bayer formats into the DCMI driver.
Those are useful e.g. when MT9P006 sensor is connected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@foss.st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Amelie DELAUNAY <amelie.delaunay@foss.st.com>
Cc: Hugues FRUCHET <hugues.fruchet@foss.st.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philippe CORNU <philippe.cornu@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Need to get dec_capability from scp first, then initialize decoder
supported format and other parameters according to dec_capability value.
Fixes: fd00d90330d1 ("media: mtk-vcodec: vdec: move stateful ops into their own file")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As dma_alloc_coherent() will return a zeroed buffer, we
don't need to memset the returned buffer.
priv_tbl = dma_alloc_coherent() and count_tbl = dma_alloc_coherent()
should be enough.
-see commit 750afb08ca71 ("cross-tree: phase out dma_zalloc_coherent()")
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When attempting to change the white balance (WB) ctrls before starting
streaming, e.g.:
# v4l2-ctl -L
User Controls
..
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
..
# v4l2-ctl --set-ctrl=blue_component_gain=500
# v4l2-ctl -L
..
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=500 flags=slider
..
These will not be written to the internal data struct and will not be
written to the WB hardware module.
Thus, after starting streaming, they will be reset to default:
# v4l2-ctl -L
..
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
..
It does not make much sense to not be able to configure the WB controls
at all times. Even if the sensor would not be RAW Bayer (and in this case the
WB module is unavailable), the user could configure the ISC itself, as the
ISC should not care about the sensor format.
Thus, when WB module is available (if the sensor changes format e.g.) it will
be already configured as be user's desires.
In consequence, remove the check in isc_s_awb_ctrl that will return if ISC
does not know the sensor format.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This driver does not use the virt_to_bus() function, though it
depends on x86 specific fixups in the swiotlb code, which was
last rewritten in commit e380a0394c36 ("x86/PCI: sta2x11: use
default DMA address translation").
It is possible that the driver still fails to build on some
architectures that are missing CONFIG_VIRT_TO_BUS, but it is
always set on x86 machines with the STA2X11 platform enabled.
More likely though is that it was never meant to depend on
CONFIG_VIRT_TO_BUS, and the Kconfig dependency was kept from
an out-of-tree version when the driver was originally merged.
Fixes: efeb98b4e2b2 ("[media] STA2X11 VIP: new V4L2 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Modify vb2ops_vdec_buf_prepare to return EINVAL if the size of the plane
is less than the size of the image. Currently we just log an error and
return 0 anyway, which may cause a buffer overrun bug.
Signed-off-by: Justin Green <greenjustin@chromium.org>
Suggested-by: Andres Calderon Jaramillo <andrescj@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the last buffer was dequeued from the capture queue,
signal userspace. DQBUF(CAPTURE) will return -EPIPE.
But if output queue is empty and capture queue is empty,
v4l2_m2m_poll_for_data will return EPOLLERR,
This is very easy to happen in drain.
When last_buffer_dequeued is set, we shouldn't return EPOLLERR,
but return EPOLLIN | EPOLLRDNORM.
Fixes: 1698a7f151126 ("media: v4l2-mem2mem: simplify poll logic")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Eliminate the following coccicheck warning:
./drivers/media/platform/mediatek/vcodec/mtk_vcodec_dec.c:71:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Error return values are supposed to be negative in hdpvr_read. Most
error returns are currently handled via an unsigned integer "ret". When
setting a negative error value to "ret", the value actually becomes a
large positive value, because "ret" is unsigned. Later on, the "ret"
value is returned. But as ssize_t is a 64-bit signed number, the error
return value stays a large positive integer instead of a negative
integer. This can cause an error value to be interpreted as the read
size, which can cause a buffer overread for applications relying on the
returned size.
Fixes: 9aba42efe85b ("V4L/DVB (11096): V4L2 Driver for the Hauppauge HD PVR usb capture device")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Maintainers of the directory Documentation/devicetree/bindings/media
are also the maintainers of the corresponding directory
include/dt-bindings/media.
Add the file entry for include/dt-bindings/media to the appropriate
section in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
