Improve the wake irq message by also printing the bank name and hwirq
number that matches this irq number.
Signed-off-by: Martin Jücker <martin.juecker@gmail.com>
Link: https://lore.kernel.org/r/20220130232122.GA119248@adroid
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Initially the driver accessed the registers using u32 __iomem but then
in the blamed commit it changed it to use regmap. The problem is that now
the offset of the registers is not calculated anymore at word offset but
at byte offset. Therefore make sure to multiply the offset with word size.
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Fixes: 2afbbab45c261a ("pinctrl: microchip-sgpio: update to support regmap")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220131085201.307031-1-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add new pinctrl driver for Amlogic's Meson-S4 SoC which share the
same register layout as the previous Meson-A1.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20220113031044.2665-4-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When PINCTRL_BCM63XX is selected,
and REGMAP is not selected,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for GPIO_REGMAP
Depends on [n]: GPIOLIB [=y] && REGMAP [=n]
Selected by [y]:
- PINCTRL_BCM63XX [=y] && PINCTRL [=y]
This is because PINCTRL_BCM63XX
selects GPIO_REGMAP without selecting or depending on
REGMAP, despite GPIO_REGMAP depending on REGMAP.
This unmet dependency bug was detected by Kismet,
a static analysis tool for Kconfig. Please advise
if this is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://lore.kernel.org/r/20220117062557.89568-1-julianbraha@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 266423e60ea1 ("pinctrl: bcm2835: Change init order for gpio
hogs") a few error paths would not unwind properly the registration of
gpio ranges. Correct that by assigning a single error label and goto it
whenever we encounter a fatal error.
Fixes: 266423e60ea1 ("pinctrl: bcm2835: Change init order for gpio hogs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220127215033.267227-1-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Couple of fixes on how Intel driver handles an interrupt
* Revert pin renaming change in ZynqMQ as it appears to be part of
the Device Tree bindings
* Fix ordering of the files in the Makefile
The following is an automated git shortlog grouped by driver:
intel:
- Fix a glitch when updating IRQ flags on a preconfigured line
- fix unexpected interrupt
Place correctly CONFIG_PINCTRL_ST in the Makefile:
- Place correctly CONFIG_PINCTRL_ST in the Makefile
zynqmp:
- Revert "Unify pin naming"
-----BEGIN PGP SIGNATURE-----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=RX4p
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.17-4' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.17-4
* Couple of fixes on how Intel driver handles an interrupt
* Revert pin renaming change in ZynqMQ as it appears to be part of
the Device Tree bindings
* Fix ordering of the files in the Makefile
The following is an automated git shortlog grouped by driver:
intel:
- Fix a glitch when updating IRQ flags on a preconfigured line
- fix unexpected interrupt
Place correctly CONFIG_PINCTRL_ST in the Makefile:
- Place correctly CONFIG_PINCTRL_ST in the Makefile
zynqmp:
- Revert "Unify pin naming"
This reverts commit 54784ff24971ed5bd3f1056edce998148709d0a7.
This patch changes the pin names from "MIO%d" to "MIO-%d", but all dts
in arch/arm64/boot/dts/xilinx still use the old name. As a result my
ZCU104 has no output on serial terminal and is not reachable over
network.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Adds Tesla FSD SoC specific data to enable pinctrl.
FSD SoC has similar pinctrl controller as found in the most
Samsung/Exynos SoCs.
Cc: linux-fsd@tesla.com
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220124141644.71052-13-alim.akhtar@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
BCM4908 has its own pins layout so it needs a custom binding and a Linux
driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220124102243.14912-2-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some boards set the direct_irq_en flag in the conf0 register without
setting the correct trigger bits. The direct_irq_en flag just means that
the GPIO will send IRQs directly to the APIC instead of going through
the shared interrupt for the GPIO controller, in order for the pin to be
able to actually generate IRQs the trigger flags must configure the IRQ
as a level-high or level-low active IRQ.
Note testing shows that using edge trigger add the conf0 register level
does NOT work, instead edge triggering should be set at the IO-APIC level.
I believe that the direct_irq_en flag connects the output of the GPIO's IRQ
trigger block, which normally sets the status flag in the IRQ status reg at
0x800 to one of the IO-APIC pins according to the direct IRQ mux.
This means that the TRIG_LVL bit *must* be set, so that the GPIO's input
value is directly passed (1:1 or inverted) to the IO-APIC pin, if TRIG_LVL
is not set, selecting edge mode operation then on the first edge the
selected IO-APIC pin goes high, but since no write-to-clear write will be
done to the IRQ status reg at 0x800, the detected edge condition will never
get cleared.
This APIC pin stuck high condition can be observed with the pin configured
as level-high active, in the form of an interrupt storm. Clearing the
TRIG_MASK bits of conf0 stops the storm, reconfiguring them as edge again
results in a storm again as soon as the edge is triggered once.
Detect invalid trigger flags, log a FW_BUG warning when encountering this
and clear the direct_irq_en flag so that a driver can actually use the pin
as IRQ through gpiod_to_irq().
Specifically this allows the edt-ft5x06 touchscreen driver to use
INT33FC:02 pin 3 as touchscreen IRQ on the Nextbook Ares 8 tablet,
accompanied by the following new log message
byt_gpio INT33FC:02: [Firmware Bug]: pin 3: direct_irq_en set without trigger, clearing
The new byt_direct_irq_sanity_check() function also checks that the
pin is actually appointed to one of the 16 direct-IRQs which the GPIO
controller supports and on success prints debug messages like these:
byt_gpio INT33FC:02: Pin 0: uses direct IRQ 0 (IO-APIC 67)
byt_gpio INT33FC:02: Pin 15: uses direct IRQ 2 (IO-APIC 69)
This is useful to figure out the GPIO pin belonging to ACPI
resources like this one: "Interrupt () { 0x00000043 }" or
the other way around.
The strict checking of valid trigger flags this introduces does result in
FW_BUG messages on quite a few devices. E.g. on the Yoga Tablet 2 1051L:
byt_gpio INT33FC:00: [Firmware Bug]: pin 92: direct_irq_en set but no IRQ assigned, clearing
byt_gpio INT33FC:00: [Firmware Bug]: pin 93: direct_irq_en set but no IRQ assigned, clearing
These 2 also have mux set to 7 and fall + rise + level trigger bits set,
presumably something has written 0xffffffff to their conf0 registers
byt_gpio INT33FC:02: Pin 3: uses direct IRQ 1 (IO-APIC 68)
byt_gpio INT33FC:02: [Firmware Bug]: pin 3: direct_irq_en set without trigger (conf0: 2803cc00h), clearing
Most tablets seem to have this, looking at DSDTs this seems intended for
use with an I2C HID sensor-hub and is still set on devices without one.
To make sure this does not cause any regressions this has been tested,
including checking disabled direct-IRQs are not used in the DSDT,
on the following devices:
Asus ME176C
Asus TF103C
Chuwi Vi10 (with its Windows BIOS)
HP x2 10-n000nd
Lenovo Yoga Tablet 2 1050L (Android version, without EC, with buggy DSDT)
Lenovo Yoga Tablet 2 1051L (Windows version, with EC)
Suggested-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The commit af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer
when switching to GPIO") hadn't taken into account an update of the IRQ
flags scenario.
When updating the IRQ flags on the preconfigured line the ->irq_set_type()
is called again. In such case the sequential Rx buffer configuration
changes may trigger a falling or rising edge interrupt that may lead,
on some platforms, to an undesired event.
This may happen because each of intel_gpio_set_gpio_mode() and
__intel_gpio_set_direction() updates the pad configuration with a different
value of the GPIORXDIS bit. Notable, that the intel_gpio_set_gpio_mode() is
called only for the pads that are configured as an input. Due to this fact,
integrate the logic of __intel_gpio_set_direction() call into the
intel_gpio_set_gpio_mode() so that the Rx buffer won't be disabled and
immediately re-enabled.
Fixes: af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
Reported-by: Kane Chen <kane.chen@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Grace Kao <grace.kao@intel.com>
ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:
->handle_irq(): 000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
IRQ_NOPROBE set
unexpected IRQ trap at vector 7c
The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Keep Makefile entries ordered in the same way as Kconfig ones.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
For Renesas PFCs not setting .strict, we can snoop GPIOs which are
already muxed to some other function. To actually make use of that, we
shouldn't mux them back to GPIO if they have been already muxed to
something.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211210113226.40111-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
While at it, replace the dev_err() with dev_dbg() as platform_get_irq()
prints an error message upon error.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220104140913.29699-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MSM GPIO IRQ controller relies on the parent IRQ controller to set the
CPU affinity for the IRQ. And this is only valid if there is any wakeup
parent available and defined in DT.
For the case of no parent IRQ controller defined in DT,
msm_gpio_irq_set_affinity() and msm_gpio_irq_set_vcpu_affinity() should
return -EINVAL instead of 0 as the affinity can't be set.
Otherwise, below warning will be printed by genirq:
genirq: irq_chip msmgpio did not update eff. affinity mask of irq 70
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220113162617.131697-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return value from pxa2xx_pinctrl_init() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Link: https://lore.kernel.org/r/20220110012730.643927-1-chi.minghao@zte.com.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two bugs have sneaked in the H616 pinctrl data:
- PH9 uses the mux value of 0x3 twice (one should be 0x5 instead)
- PH8 and PH9 use the "i2s3" function name twice in each pin
For the double pin name we use the same trick we pulled for i2s0: append
the pin function to the group name to designate the special function.
Fixes: 25adc29407fb ("pinctrl: sunxi: Add support for the Allwinner H616 pin controller")
Reported-by: SASANO Takayoshi <uaa@mx5.nisiq.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220105172952.23347-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit bdfbef2d29dc ("pinctrl: cherryview: Don't use selection 0 to mark
an interrupt line as unused") made the code properly differentiate
between unset vs (hwirq) 0 entries in the GPIO-controller interrupt-line
to GPIO pinnumber/hwirq mapping.
This is causing some boards to not boot. This commit restores the old
behavior of triggering hwirq 0 when receiving an interrupt on an
interrupt-line for which there is no mapping.
Fixes: bdfbef2d29dc ("pinctrl: cherryview: Don't use selection 0 to mark an interrupt line as unused")
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220104164238.253142-1-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the outer loop iterate over functions as that's the real subject.
This simplifies code (and reduces amount of lines of code) as allocating
memory for names doesn't require extra checks anymore.
While at it use local "group_names" variable. It fixes:
drivers/pinctrl/pinctrl-thunderbay.c: In function 'thunderbay_add_functions':
drivers/pinctrl/pinctrl-thunderbay.c:815:8: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
815 | grp = func->group_names;
| ^
Ref: c26c4bfc1040 ("pinctrl: keembay: rework loops looking for groups names")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20220111172919.6567-2-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This should make code a bit easier to follow. While at it use some "for"
loops to simplify array iteration loops.
Ref: 5d0674999cc5 ("pinctrl: keembay: comment process of building functions a bit")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20220111172919.6567-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It seems that newer ARMv8 Exynos SoC like Exynos850 and
ExynosAutov9 have differences of their pin controller node capable of
external wake-up interrupts:
1. No multiplexed external wake-up interrupt, only direct,
2. More than one pin controller capable of external wake-up interrupts.
Add support for dedicated Exynos850 and ExynosAutov9 compatibles.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220111201722.327219-20-krzysztof.kozlowski@canonical.com
Existing dt-bindings expected that each GPIO/pin bank within pin
controller has its own node with name matching the bank (e.g. gpa0,
gpx2) and "gpio-controller" property. The node name is then used for
matching between driver data and DTS.
Newly introduced dtschema expects to have nodes ending with "-gpio-bank"
suffix, so rewrite bank-devicetree matching to look for old and new
style of naming.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20220111201426.326777-3-krzysztof.kozlowski@canonical.com
GPIO_ALIVE and GPIO_CMGP blocks in Exynos850 SoC don't have EINT
capabilities (like EINT_SVC register), and there are no corresponding
interrupts wired to GIC. Instead those blocks have wake-up interrupts
for each pin. The ".eint_gpio_init" callbacks were specified by mistake
for these blocks, when porting pinctrl code from downstream kernel. That
leads to error messages like this:
samsung-pinctrl 11850000.pinctrl: irq number not available
Remove ".eint_gpio_init" for pinctrl_alive and pinctrl_gpmc to fix this
error. This change doesn't affect proper interrupt handling for related
pins, as all those pins are handled in ".eint_wkup_init".
Fixes: cdd3d945dcec ("pinctrl: samsung: Add Exynos850 SoC specific data")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20220114203757.4860-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The driver iterates over its devicetree children with
for_each_child_of_node() and stores for later found node pointer. This
has to be put in error paths to avoid leak during re-probing.
Fixes: ab663789d697 ("pinctrl: samsung: Match pin banks with their device nodes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220111201426.326777-2-krzysztof.kozlowski@canonical.com
Core changes:
- New standard enumerator and corresponding device tree bindings
for output impedance pin configuration. (Implemented and used
in the Renesas rzg2l driver.)
- Cleanup of Kconfig and Makefile to be somewhat orderly and
alphabetic.
New drivers:
- Samsung Exynos 7885 pin controller.
- Ocelot LAN966x pin controller.
- Qualcomm SDX65 pin controller.
- Qualcomm SM8450 pin controller.
- Qualcomm PM8019, PM8226 and PM2250 pin controllers.
- NXP/Freescale i.MXRT1050 pin controller.
- Intel Thunder Bay pin controller.
Enhancements:
- Introduction of the string library helper function
"kasprintf_strarray()" and subsequent use in Rockchip, ST and
Armada pin control drivers, as well as the GPIO mockup driver.
- The Ocelot pin controller has been extensively rewritten to
use regmap and other modern kernel infrastructure.
- The Microchip SGPIO driver has been converted to use regmap.
- The SPEAr driver had been converted to use regmap.
- Substantial cleanups and janitorial on the Apple pin control
driver that was merged for v5.16.
- Janitorial to remove of_node assignments in the GPIO portions
that anyway get this handled in the GPIO core.
- Minor cleanups and improvements in several pin controllers.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmHetMgACgkQQRCzN7AZ
XXOXUA/+I8nEdBy8oBa+vYsJp/FwQi9oh2r488Bin7kCEwYJjPKDDjZuIQQQz34H
DcSpzBBB/sSFiO27F27rk70vHGfZ4pVi57XfRI2IB1qSe4uCNCNEURVDSM9aY7Nl
hR973GS5VDvmyo/7zUT7dWmG2b9lxRqwU2wCvVJ7y69gQEwT74iR8b51ycziBNWt
AEQ+BUN9oVEIM6aHs9+jGgD843XIFZMWoKuwoD51036/wFDLO3lQNyuMytZaQtSB
q1epb51jl4tPhybWrWc+IoVp6BshIZs1m8+LhgRqLfJEj1znTZDXvAEuTuI3Y9BY
lyyvGuKNbe6q1aD8Hfu3qiO8PfBrI+pNpOcdw84pG6IwBz4vfLmhzyMd8vTyqoK8
DIlfYCiGJB0aqDBWhRyql8KM04/gSlEm2eZONsudNuMugvRIxU1IOBaKFwlP5Z98
y2/mYo/wLnVFKZE6cLp3Lxjpv4ENRJ1HkQe5JQak1ulq+XkUL9f82p7oGMJ4lvoB
iTOPTkuhhkiUYmwbb97VoqWTYwL+EptvsWto+Mv/glHy7OGXXJFTAD+ARpZc+c5I
f1/mzQYujmVj91XUi9xSGnL07mNNPOiX3p+9q7Fy+A3Rk1x5n0t+7hvmiuv8paLv
KNowhECllp0lBKns39tcn8BQvRufvxv2b+QvEqgUPVI3Qj8vEc4=
=+nxh
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk updates from Linus Walleij:
"Core changes:
- New standard enumerator and corresponding device tree bindings for
output impedance pin configuration. (Implemented and used in the
Renesas rzg2l driver.)
- Cleanup of Kconfig and Makefile to be somewhat orderly and
alphabetic.
New drivers:
- Samsung Exynos 7885 pin controller.
- Ocelot LAN966x pin controller.
- Qualcomm SDX65 pin controller.
- Qualcomm SM8450 pin controller.
- Qualcomm PM8019, PM8226 and PM2250 pin controllers.
- NXP/Freescale i.MXRT1050 pin controller.
- Intel Thunder Bay pin controller.
Enhancements:
- Introduction of the string library helper function
"kasprintf_strarray()" and subsequent use in Rockchip, ST and
Armada pin control drivers, as well as the GPIO mockup driver.
- The Ocelot pin controller has been extensively rewritten to use
regmap and other modern kernel infrastructure.
- The Microchip SGPIO driver has been converted to use regmap.
- The SPEAr driver had been converted to use regmap.
- Substantial cleanups and janitorial on the Apple pin control driver
that was merged for v5.16.
- Janitorial to remove of_node assignments in the GPIO portions that
anyway get this handled in the GPIO core.
- Minor cleanups and improvements in several pin controllers"
* tag 'pinctrl-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (98 commits)
pinctrl: imx: fix assigning groups names
dt-bindings: pinctrl: mt8195: add wrapping node of pin configurations
pinctrl: bcm: ns: use generic groups & functions helpers
pinctrl: imx: fix allocation result check
pinctrl: samsung: Use platform_get_irq_optional() to get the interrupt
pinctrl: Propagate firmware node from a parent device
dt-bindings: pinctrl: qcom: Add SDX65 pinctrl bindings
pinctrl: add one more "const" for generic function groups
pinctrl: keembay: rework loops looking for groups names
pinctrl: keembay: comment process of building functions a bit
pinctrl: imx: prepare for making "group_names" in "function_desc" const
ARM: dts: gpio-ranges property is now required
pinctrl: aspeed: fix unmet dependencies on MFD_SYSCON for PINCTRL_ASPEED
pinctrl: Get rid of duplicate of_node assignment in the drivers
pinctrl-sunxi: don't call pinctrl_gpio_direction()
pinctrl-bcm2835: don't call pinctrl_gpio_direction()
pinctrl: bcm2835: Silence uninit warning
pinctrl: Sort Kconfig and Makefile entries alphabetically
pinctrl: Add Intel Thunder Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Thunderbay pinctrl driver
...
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype
board, with additional boards to be added later. This SoC promises
to be the first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding
a few other Arm based SoCs as well, but those did not pass the
review in time, so it's only this one.
-----BEGIN PGP SIGNATURE-----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=X5uk
-----END PGP SIGNATURE-----
Merge tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull RISC-V SoC updates from Arnd Bergmann:
"Add support for StarFive JH7100 RISC-V SoC
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype board,
with additional boards to be added later. This SoC promises to be the
first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding a
few other Arm based SoCs as well, but those did not pass the review in
time, so it's only this one"
* tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
reset: starfive-jh7100: Fix 32bit compilation
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
1. Add support for Exynos7885.
2. Drop usage of platform_get_resource().
-----BEGIN PGP SIGNATURE-----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=hka6
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-5.17' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v5.17
1. Add support for Exynos7885.
2. Drop usage of platform_get_resource().
This simplifies ns driver and gets rid of ~70 lines of code.
"const" had to be dropped from "struct ns_pinctrl_group" @pins to match
"struct group_desc" @pins and pinctrl_generic_add_group(). Otherwise it
would cause:
drivers/pinctrl/bcm/pinctrl-ns.c: In function 'ns_pinctrl_probe':
drivers/pinctrl/bcm/pinctrl-ns.c:277:13: warning: passing argument 3 of 'pinctrl_generic_add_group' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
277 | group->pins, group->num_pins, NULL);
| ~~~~~^~~~~~
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211222064344.14624-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix code to check correct variable value.
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Fixes: 02f117134952 ("pinctrl: imx: prepare for making "group_names" in "function_desc" const")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20211222212807.27122-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224145748.18754-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
When creating MFD platform devices the firmware node is left unset.
This, in particular, prevents GPIO library to use it for different
purposes. Propagate firmware node from the parent device and let
GPIO library do the right thing.
While at it, slightly modify the headers to reflect the usage of APIs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20211216151227.58687-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Generic code doesn't modify those strings and .get_function_groups
callback has that extra "const" as well. This allows more flexibility in
GENERIC_PINMUX_FUNCTIONS users.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-4-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the outer loop iterate over functions as that's the real subject.
This simplifies code (and reduces amount of lines of code) as allocating
memory for names doesn't require extra checks anymore.
While at it use local "group_names" variable. The plan for
"struct function_desc" is to make its "group_names" /double/ const. That
will allow drivers to use it with static const data.
This keembay "group_names" change is required to avoid:
drivers/pinctrl/pinctrl-keembay.c: In function 'keembay_add_functions':
drivers/pinctrl/pinctrl-keembay.c:1594:8: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1594 | grp = func->group_names;
| ^
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-3-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This should make code a bit easier to follow. While at it use some "for"
loops to simplify array iteration loops.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-2-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The plan for "struct function_desc" is to make its "group_names"
/double/ const. That will allow drivers to use it with static const
data.
This imx change is required to avoid:
drivers/pinctrl/freescale/pinctrl-imx.c: In function 'imx_pinctrl_parse_functions':
drivers/pinctrl/freescale/pinctrl-imx.c:672:24: error: assignment of read-only location '*(func->group_names + (sizetype)(i * 4))'
672 | func->group_names[i] = child->name;
| ^
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211216162206.8027-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Align comments in the R-Car V3U pin control driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYbxj9gAKCRCKwlD9ZEnx
cMhKAQD+V66ADB9lwaSKLNwxK5TA8v6hpJTOP7FXFcbhpzafyQD/d9QETuTFehxZ
PyNfggjhzv6yi0qdIOvbv+t4lcf/4wo=
=WvSa
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.17 (take two)
- Align comments in the R-Car V3U pin control driver.
This adds support for the StarFive JH7100 RISC-V SoC. The SoC has many
devices that need non-coherent DMA operations to work which isn't
upstream yet[1], so this just adds basic support to boot up, get a
serial console, blink an LED and reboot itself. Unlike the Allwinner D1
this chip doesn't use any extra pagetable bits, but instead the DDR RAM
appears twice in the memory map, with and without the cache.
The JH7100 is a test chip for the upcoming JH7110 and about 300 BeagleV
Starlight Beta boards were sent out with them as part of a now cancelled
BeagleBoard.org project. However StarFive has produced more of the
JH7100s and will be selling VisionFive boards with them soon[2].
[1]: https://lore.kernel.org/linux-riscv/20210723214031.3251801-2-atish.patra@wdc.com/
[2]: https://www.cnx-software.com/2021/12/09/starfive-visionfive-single-board-computer-for-sale-accelerating-risc-v-ecosystem-development/
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTtU6YTJ5V9vBl9M/+39ymfrXW1/gUCYbtpnAAKCRC39ymfrXW1
/skTAQD6hDKWL5jLLCa4fN6yaovSC9RC4EPYmXpj2krzFMqcvwEA/OFHLp+buXhV
n1BGpTieVfRMV5HJZhFK3aAED9+SQQY=
=r5lD
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmG7bpoACgkQmmx57+YA
GNkDdg//dJTDLeCkrQuRIui8nkvmfsWz6Y8x1DcW4//soqJ5rnSBJJ5Gq2iAnEH4
VykUY8rW72nciU/JzSwM3Qdxyvug4xYoHAit8Rae5km4yi290cIrKmFotXjS2JSN
3ckEbe6VOunvR8mhxXXcDOINRka+6Lj7y1S+L6Fg8dl8Y8AEo8ZAdb0wytrP37lg
QzOpjir/clYVnIDK1jq9J3GqiY2AcnlmrLIKNJMvdc5c5Y9LCkxiZ1HDbuqwP70c
vCbwxbww2y5TYVRjDrB+fAQak7/xgZZQrZSaMNFn0MDnmas8UjMDL1nvdYf0WwD0
5E6uhIFBNOIZ8TKKE0JdDM75JSsHa03kxy79t9U5dgH4M/JAp4v5p0g32kVTSm/H
F8L2KukzKQ65SzJm9cBVDinYp11FQ025NV0Vhne7y3UzH1QCp9KeMeqXJ9o+PRnj
80xWERuaKyiYOJfvPmJgO53Satfij/fjNsvKy6MLCC5jenkKFKutG3DAG+kitHWj
s4invacyYqnzTd3Pai/ZtMVt/dC7pIaitm2l675jIdf5TEtxvmyQ54FdeidkmdGi
mPe478oDXZSjKGH/0SN0SYl7bl4nex8m+HN066ZjgocQ35JVwUqbYa9PNGoQ5/6Y
X3BvJt/EwoEX8c+i3GyB9QhP57EX30sh1jIXUeQAniskPx6fzYU=
=TBjW
-----END PGP SIGNATURE-----
Merge tag 'jh7100-for-5.17' of https://github.com/esmil/linux into arm/newsoc
Basic StarFive JH7100 RISC-V SoC support
This adds support for the StarFive JH7100 RISC-V SoC. The SoC has many
devices that need non-coherent DMA operations to work which isn't
upstream yet[1], so this just adds basic support to boot up, get a
serial console, blink an LED and reboot itself. Unlike the Allwinner D1
this chip doesn't use any extra pagetable bits, but instead the DDR RAM
appears twice in the memory map, with and without the cache.
The JH7100 is a test chip for the upcoming JH7110 and about 300 BeagleV
Starlight Beta boards were sent out with them as part of a now cancelled
BeagleBoard.org project. However StarFive has produced more of the
JH7100s and will be selling VisionFive boards with them soon[2].
[1]: https://lore.kernel.org/linux-riscv/20210723214031.3251801-2-atish.patra@wdc.com/
[2]: https://www.cnx-software.com/2021/12/09/starfive-visionfive-single-board-computer-for-sale-accelerating-risc-v-ecosystem-development/
* tag 'jh7100-for-5.17' of https://github.com/esmil/linux:
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
Link: https://lore.kernel.org/r/20211216164205.286138-1-kernel@esmil.dk
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a combined pinctrl and GPIO driver for the JH7100 RISC-V SoC by
StarFive Ltd. This is a test chip for their upcoming JH7110 SoC, which
is said to feature only minor changes to these pinctrl/GPIO parts.
For each "GPIO" there are two registers for configuring the output and
output enable signals which may come from other peripherals. Among these
are two special signals that are constant 0 and constant 1 respectively.
Controlling the GPIOs from software is done by choosing one of these
signals. In other words the same registers are used for both pin muxing
and controlling the GPIOs, which makes it easier to combine the pinctrl
and GPIO driver in one.
I wrote the pinconf and pinmux parts, but the GPIO part of the code is
based on the GPIO driver in the vendor tree written by Huan Feng with
cleanups and fixes by Drew and me.
Datasheet: https://github.com/starfive-tech/JH7100_Docs/blob/main/JH7100%20Data%20Sheet%20V01.01.04-EN%20(4-21-2021).pdf
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Co-developed-by: Huan Feng <huan.feng@starfivetech.com>
Signed-off-by: Huan Feng <huan.feng@starfivetech.com>
Co-developed-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
