Support for Tegra234 was added to the tegra186 driver in 1db9b241bb (
"gpio: tegra186: Add support for Tegra234"). But the driver is not
selectable on Tegra234. Update the Kconfig entry to allow the driver to be
enabled on Tegra234.
Enable the driver by default on Tegra 234 as well, similar to the other
platforms it supports.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241113162939.886242-1-lars@metafoo.de
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add a driver to support the Polarfire SoC gpio controller. Interrupt
controller support is unavailable for now and will be added at a later
date.
Signed-off-by: Lewis Hanly <lewis.hanly@microchip.com>
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241104-tiny-evaluate-9336020b4b6a@spud
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The 'if !EXPERT' bit will work fine if it follows the 'bool "foobar"'
declaration. No need to have separate entries for it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241014110707.101320-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Make it possible to build the module when COMPILE_TEST is enabled for
better build coverage. Stop using of_match_ptr() to avoid build warnings.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241007103440.38416-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver doesn't really depend on interfaces from OF_GPIO so the
Kconfig dependency can be dropped.
Suggested-by: Uwe Kleine-König <ukleinek@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org>
Link: https://lore.kernel.org/r/20241008081555.23465-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
FTDI FT2232H is a USB to GPIO chip. Sealevel produces some devices
with this chip. FT2232H presents itself as a composite device with two
interfaces (each is an "MPSSE"). Each MPSSE has two banks (high and low)
of 8 GPIO each. I believe some MPSSE's have only one bank, but I don't
know how to identify them (I don't have any for testing) and as a result
are unsupported for the time being.
Additionally, this driver provides software polling-based interrupts for
edge detection. For the Sealevel device I have to test with, this works
well because there is hardware debouncing. From talking to Sealevel's
people, this is their preferred way to do edge detection.
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241009131131.1618329-1-mstrodl@csh.rit.edu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
-----BEGIN PGP SIGNATURE-----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=vhYn
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-i2c-watchdog-v6.13' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO, I2C and Watchdog due for the v6.13 merge window
Add gpio support for the Congatec Board Controller.
This Board Controller has 14 GPIO pins.
The driver is probed by the Congatec Board Controller MFD driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241001-congatec-board-controller-v3-2-39ceceed5c47@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
This driver doesn't really depend on gpiolib-of being built and can be
compiled without it.
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240930144804.75068-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the GPIO function using the platform device
registered by the core MFD driver.
The driver is derived from an initial implementation from NXP, available
in commit 451f61b46b76 ("MLK-25917-2 gpio: adp5585-gpio: add
adp5585-gpio support") in their BSP kernel tree. It has been extensively
rewritten.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240722121100.2855-4-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more info
on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core to using
a safer alternative
- use array_index_nospec() where applicable
New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs from actual
hardware and driving tests of the in-kernel GPIO API from user-space over
debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first glance"
debugging on remote boards
Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested as irqs
via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to errno
vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture
DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio
Documentation:
- document stricter behavior of the GPIO character device uAPI with regards to
reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop tempting
people to use it
- document the preference for using pread() for reading edge events in the
sysfs API
Other:
- add an extended initializer to the interrupt simulator allowing to specify
a number of callbacks callers can use to be notified about irqs being
requested and released
-----BEGIN PGP SIGNATURE-----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=kK88
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"The majority of added lines are two new modules: the GPIO virtual
consumer module that improves our ability to add automated tests for
the kernel API and the "sloppy" logic analyzer module that uses the
GPIO API to implement a coarse-grained debugging tool for useful for
remote development.
Other than that we have the usual assortment of various driver
extensions, improvements to the core GPIO code, DT-bindings and other
documentation updates as well as an extension to the interrupt
simulator:
GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more
info on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot
fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core
to using a safer alternative
- use array_index_nospec() where applicable
New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs
from actual hardware and driving tests of the in-kernel GPIO API
from user-space over debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first
glance" debugging on remote boards
Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested
as irqs via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to
errno vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture
DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and
gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio
Documentation:
- document stricter behavior of the GPIO character device uAPI with
regards to reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop
tempting people to use it
- document the preference for using pread() for reading edge events
in the sysfs API
Other:
- add an extended initializer to the interrupt simulator allowing to
specify a number of callbacks callers can use to be notified about
irqs being requested and released"
* tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (41 commits)
gpio: mc33880: Convert comma to semicolon
gpio: virtuser: actually use the "trimmed" local variable
dt-bindings: gpio: convert Atmel GPIO to json-schema
gpio: virtuser: new virtual testing driver for the GPIO API
dt-bindings: gpio: vf610: Allow gpio-line-names to be set
gpio: sim: lock GPIOs as interrupts when they are requested
genirq/irq_sim: add an extended irq_sim initializer
dt-bindings: gpio: fsl,qoriq-gpio: Add compatible string fsl,ls1046a-gpio
gpiolib: unexport gpiochip_get_desc()
gpio: add sloppy logic analyzer using polling
Documentation: gpio: Reconfiguration with unset direction (uAPI v2)
Documentation: gpio: Reconfiguration with unset direction (uAPI v1)
dt-bindings: gpio: fsl,qoriq-gpio: add common property gpio-line-names
gpio: ath79: convert to dynamic GPIO base allocation
pinctrl: da9062: replace gpiochip_get_desc() with gpio_device_get_desc()
gpiolib: put gpio_suffixes in a single compilation unit
Documentation: gpio: Clarify effect of active low flag on line edges
Documentation: gpio: Clarify effect of active low flag on line values
gpiolib: Remove data-less gpiochip_add() function
gpio: sim: use devm_mutex_init()
...
The GPIO subsystem used to have a serious problem with undefined behavior
and use-after-free bugs on hot-unplug of GPIO chips. This can be
considered a corner-case by some as most GPIO controllers are enabled
early in the boot process and live until the system goes down but most
GPIO drivers do allow unbind over sysfs, many are loadable modules that
can be (force) unloaded and there are also GPIO devices that can be
dynamically detached, for instance CP2112 which is a USB GPIO expender.
Bugs can be triggered both from user-space as well as by in-kernel users.
We have the means of testing it from user-space via the character device
but the issues manifest themselves differently in the kernel.
This is a proposition of adding a new virtual driver - a configurable
GPIO consumer that can be configured over configfs (similarly to
gpio-sim) or described on the device-tree.
This driver is aimed as a helper in spotting any regressions in
hot-unplug handling in GPIOLIB.
Link: https://lore.kernel.org/r/20240708142912.120570-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This is a sloppy logic analyzer using GPIOs. It comes with a script to
isolate a CPU for polling. While this is definitely not a production
level analyzer, it can be a helpful first view when remote debugging.
Read the documentation for details.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240620094159.6785-2-wsa+renesas@sang-engineering.com
[Bartosz: moved the Kconfig entry into a different category]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The GPIO_BRCMSTB hardware IP is also included in the bcm2712
SoC so enable the driver to also be built for ARCH_BCM2835.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240530181737.1261450-1-pbrobinson@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
GPIO core:
- remove more unused legacy interfaces (after converting the last remaining
users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos
-----BEGIN PGP SIGNATURE-----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=mBWd
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski
"This was a quiet release cycle for the GPIO tree and so this
pull-request is relatively small.
We have one new driver, some minor improvements to the GPIO core code
and across several drivers, some DT and documentation updates but in
general nothing stands out or is controversial. All changes have spent
time in next with no reported issues (or ones that were quickly
fixed).
GPIO core:
- remove more unused legacy interfaces (after converting the last
remaining users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name
fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple
GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to
gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos"
* tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (30 commits)
gpio: nuvoton: Fix sgpio irq handle error
gpiolib: Discourage to use formatting strings in line names
gpio: brcmstb: add support for gpio-ranges
gpio: of: support gpio-ranges for multiple gpiochip devices
dt-bindings: gpio: brcmstb: add gpio-ranges
gpio: Add Intel Granite Rapids-D vGPIO driver
gpio: brcmstb: Use dynamic GPIO base numbers
gpiolib: acpi: Set label for IRQ only lines
gpiolib: acpi: Add fwnode name to the GPIO interrupt label
gpiolib: Get rid of never false gpio_is_valid() calls
gpiolib: acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
gpiolib: acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
gpiolib: acpi: Simplify error handling in __acpi_find_gpio()
gpiolib: acpi: Extract __acpi_find_gpio() helper
gpio: sch: Utilise temporary variable for struct device
gpio: sch: Switch to memory mapped IO accessors
gpio: regmap: Use -ENOTSUPP consistently
gpio: pcie-idio-24: Use -ENOTSUPP consistently
Documentation: gpio: Replace leading TABs by spaces in code blocks
gpiolib: acpi: Check for errors first in acpi_find_gpio()
...
This driver provides a basic GPIO driver for the Intel Granite Rapids-D
virtual GPIOs. On SoCs with limited physical pins on the package, the
physical pins controlled by this driver would be exposed on an external
device such as a BMC or CPLD. The virtual GPIO registers are an
interface to firmware, which communicates with the external device that
implements the GPIO hardware functionality.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
SPI devices can specify a cs-gpios property to enumerate their
chip selects. Under device tree, a zero entry in this property can
be used to specify that a particular chip select is using the SPI
controllers native chip select, for example:
cs-gpios = <&gpio1 0 0>, <0>;
Here, the second chip select is native. However, when using swnodes
there is currently no way to specify a native chip select. The
proposal here is to register a swnode_gpio_undefined software node,
that can be specified to allow the indication of a native chip
select. For example:
static const struct software_node_ref_args device_cs_refs[] = {
{
.node = &device_gpiochip_swnode,
.nargs = 2,
.args = { 0, GPIO_ACTIVE_LOW },
},
{
.node = &swnode_gpio_undefined,
.nargs = 0,
},
};
Register the swnode as the gpiolib is initialised and check in
swnode_get_gpio_device() if the returned node matches
swnode_gpio_undefined and return -ENOENT, which matches the
behaviour of the device tree system when it encounters a 0 phandle.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander.
I found this living out-of-tree in OpenWrt as an upstream
attempt had stalled on the finishing line, so I picked it
up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of
tree for the ST STA chips, and now the IP was re-used in a
MIPS automotive SoC called MobilEyeq5, so it has been split
in pin control and GPIO drivers so the latter can be reused
by MobilEyeq5. (Along with a long list of cleanups.)
- A lot of overall cleanup and tidying up.
-----BEGIN PGP SIGNATURE-----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=Pt9Y
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander. I found this
living out-of-tree in OpenWrt as an upstream attempt had stalled on
the finishing line, so I picked it up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of tree
for the ST STA chips, and now the IP was re-used in a MIPS
automotive SoC called MobilEyeq5, so it has been split in pin
control and GPIO drivers so the latter can be reused by MobilEyeq5.
(Along with a long list of cleanups)
- A lot of overall cleanup and tidying up"
* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
dt-bindings: pinctrl: qcom: update compatible name for match with driver
pinctrl: aw9523: Make the driver tristate
pinctrl: nomadik: fix dereference of error pointer
gpio: nomadik: Back out some managed resources
pinctrl: aw9523: Add proper terminator
pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
gpio: nomadik: Finish conversion to use firmware node APIs
gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
pinctrl: da9062: Add OF table
dt-bindings: pinctrl: at91: add sam9x7
pinctrl: ocelot: remove redundant assignment to variable ret
gpio: nomadik: grab optional reset control and deassert it at probe
gpio: nomadik: support mobileye,eyeq5-gpio
gpio: nomadik: handle variadic GPIO count
gpio: nomadik: support shared GPIO IRQs
...
Previously driver got a few updates in order to replace OF APIs by
respective firmware node, however it was not finished to the logical
end, e.g., some APIs that has been used are still require OF node
to be passed. Finish that job by converting leftovers to use firmware
node APIs.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240302173401.217830-1-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We create a custom compatible for the STA2X11 IP block as integrated
into the Mobileye EyeQ5 platform. Its wake and alternate functions have
been disabled, we want to avoid touching those registers.
We both do: (1) early return in functions that do not support the
platform, but with warnings, and (2) avoid calling those functions in
the first place.
We ensure that pinctrl-nomadik is not used with this STA2X11 variant.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-24-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously, drivers/pinctrl/nomadik/pinctrl-nomadik.c registered two
platform drivers: pinctrl & GPIO. Move the GPIO aspect to the
drivers/gpio/ folder, as would be expected.
Both drivers are intertwined for a reason; pinctrl requires access to
GPIO registers for pinmuxing, pull-disable, disabling interrupts while
setting the muxing and wakeup control. Information sharing is done
through a shared array containing GPIO chips and a few helper
functions. That shared array is not touched from gpio-nomadik when
CONFIG_PINCTRL_NOMADIK is not defined.
Make no change to the code that moved into gpio-nomadik; there should be
no behavior change following. A few functions are shared and header
comments are added. Checkpatch warnings are addressed. NUM_BANKS is
renamed to NMK_MAX_BANKS.
It is supported to compile gpio-nomadik without pinctrl-nomadik. The
opposite is not true.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-6-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ChromeOS embedded controller (EC) supports setting the state of
GPIOs when the system is unlocked, and getting the state of GPIOs in all
cases. The GPIOs are on the EC itself, so the EC acts similar to a GPIO
expander. Add a driver to get and set the GPIOs on the EC through the
host command interface.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Enable COMPILE_TEST for the vf610 gpio driver to support test builds on
systems without this hardware.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The vf610 gpio driver is enabled by default for all i.MX machines,
without any option to disable it in a board-specific config file.
Most i.MX chipsets have no hardware for this driver. Change the default
to enable GPIO_VF610 for SOC_VF610 and disable it otherwise.
Add a text description after the bool type, this makes the driver
selectable by make config etc.
Fixes: 30a35c07d9 ("gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver support.
Nuvoton NPCM SGPIO module is combine serial to parallel IC (HC595)
and parallel to serial IC (HC165), and use APB3 clock to control it.
This interface has 4 pins (D_out , D_in, S_CLK, LDSH).
BMC can use this driver to increase 64 GPI pins and 64 GPO pins to use.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for new
hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio, spi,
and i2c drivers for that type of device (all acked by the respective
subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems, EXCEPT for some merge conflicts that you will run
into in your tree. 2 of them are in device-tree files, which will be
trivial to resolve (accept both sides), and the last in the
drivers/gpio/gpio-ljca.c file, in the remove callback, resolution should
be pretty trivial (take the version in this branch), see here:
https://lore.kernel.org/all/20231016134159.11d8f849@canb.auug.org.au/
for details, or I can provide a resolved merge point if needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUStew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxgQCggUyfGo+JVV8XZVu5A9KwT6nr7mUAmwUgFxhZ
khK77t0KqF4hjXryeaHa
=iPd+
-----END PGP SIGNATURE-----
Merge tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
This driver communicate with LJCA GPIO module with specific
protocol through interfaces exported by LJCA USB driver.
Update the driver according to LJCA USB driver's changes.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/1696833205-16716-5-git-send-email-wentong.wu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a much better alternative to the clunky old gpio-mockup. Don't
remove it just yet (there are tests depending on it out there) but make
Kconfig say that it should no longer be used in new projects.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
The WinSystems WS16C48 provides the following registers:
Offset 0x0-0x5: Port 0-5 I/O
Offset 0x6: Int_Pending
Offset 0x7: Page/Lock
Offset 0x8-0xA (Page 1): Pol_0-Pol_2
Offset 0x8-0xA (Page 2): Enab_0-Enab_2
Offset 0x8-0xA (Page 3): Int_ID0-Int_ID2
Port 0-5 I/O provides access to 48 lines of digital I/O across six
registers, each bit position corresponding to the respective line.
Writing a 1 to a respective bit position causes that output pin to sink
current, while writing a 0 to the same bit position causes that output
pin to go to a high-impedance state and allows it to be used an input.
Reads on a port report the inverted state (0 = high, 1 = low) of an I/O
pin when used in input mode. Interrupts are supported on Port 0-2.
Int_Pending is a read-only register that reports the combined state of
the INT_ID0 through INT_ID2 registers; an interrupt pending is indicated
when any of the low three bits are set.
The Page/Lock register provides the following bits:
Bit 0-5: Port 0-5 I/O Lock
Bit 6-7: Page 0-3 Selection
For Bits 0-5, writing a 1 to a respective bit position locks the output
state of the corresponding I/O port. Writing the page number to Bits 6-7
selects that respective register page for use.
Pol_0-Pol_2 are accessible when Page 1 is selected. Writing a 1 to a
respective bit position selects the rising edge detection interrupts for
that input line, while writing a 0 to the same bit position selects the
falling edge detection interrupts.
Enab_0-Enab_2 are accessible when Page 2 is selected. Writing a 1 to a
respective bit position enables interrupts for that input line, while
writing a 0 to that same bit position clears and disables interrupts for
that input line.
Int_ID0-Int_ID2 are accessible when Page 3 is selected. A respective bit
when read as a 1 indicates that an edge of the polarity set in the
corresponding polarity register was detected for the corresponding input
line. Writing any value to this register clears all pending interrupts
for the register.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/f59de81e80f7198bcfa9a15615c459c38b5d0e08.1680708357.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
For the PCIe-IDIO-24 series of devices, the following BARs are
available:
BAR[0]: memory mapped PEX8311
BAR[1]: I/O mapped PEX8311
BAR[2]: I/O mapped card registers
There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS
lines (which may be configured for either output or input). The GPIO
lines are exposed by the following card registers:
Base +0x0-0x2 (Read/Write): FET Outputs
Base +0xB (Read/Write): TTL/CMOS
Base +0x4-0x6 (Read): Isolated Inputs
Base +0x7 (Read): TTL/CMOS
In order for the device to support interrupts, the PLX PEX8311 internal
PCI wire interrupt and local interrupt input must first be enabled.
The following card registers for Change-Of-State may be used:
Base +0x8-0xA (Read): COS Status Inputs
Base +0x8-0xA (Write): COS Clear Inputs
Base +0xB (Read): COS Status TTL/CMOS
Base +0xB (Write): COS Clear TTL/CMOS
Base +0xE (Read/Write): COS Enable
The COS Enable register is used to enable/disable interrupts and
configure the interrupt levels; each bit maps to a group of eight inputs
as described below:
Bit 0: IRQ EN Rising Edge IN0-7
Bit 1: IRQ EN Rising Edge IN8-15
Bit 2: IRQ EN Rising Edge IN16-23
Bit 3: IRQ EN Rising Edge TTL0-7
Bit 4: IRQ EN Falling Edge IN0-7
Bit 5: IRQ EN Falling Edge IN8-15
Bit 6: IRQ EN Falling Edge IN16-23
Bit 7: IRQ EN Falling Edge TTL0-7
An interrupt is asserted when a change-of-state matching the interrupt
level configuration respective for a particular group of eight inputs
with enabled COS is detected.
The COS Status registers may be read to determine which inputs have
changed; if interrupts were enabled, an IRQ will be generated for the
set bits in these registers. Writing the value read from the COS Status
register back to the respective COS Clear register will clear just those
interrupts.
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the pci-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/5ba5405c64aca984d5cf3bdbdffa04c325e5a147.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver. Migrate the 104-idio-16 module to the new
idio-16 library interface leveraging the gpio-regmap API.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1f24a1f18c9a9daa4983713e0a5b53e838d624a8.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
By leveraging the regmap API, the idio-16 library is reduced to simply a
devm_idio_16_regmap_register() function and a configuration structure
struct idio_16_regmap_config.
Legacy functions and code will be removed once all consumers have
migrated to the new idio-16 library interface.
For IDIO-16 devices we have the following IRQ registers:
Base Address +1 (Write): Clear Interrupt
Base Address +2 (Read): Enable Interrupt
Base Address +2 (Write): Disable Interrupt
An interrupt is asserted whenever a change-of-state is detected on any
of the inputs. Any write to 0x2 will disable interrupts, while any read
will enable interrupts. Interrupts are cleared by a write to 0x1.
For 104-IDIO-16 devices, there is no IRQ status register, so software
has to assume that if an interrupt is raised then it was for the
104-IDIO-16 device.
For PCI-IDIO-16 devices, there is an additional IRQ register:
Base Address +6 (Read): Interrupt Status
Interrupt status can be read from 0x6 where bit 2 set indicates that an
IRQ has been generated.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b45081958ab53dfa697f4a8b15f1bfba46718068.1680618405.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The DS4520 is a 9-bit nonvolatile (NV) I/O expander.
It offers users a digitally programmable alternative
to hardware jumpers and mechanical switches that are
being used to control digital logic node.
Signed-off-by: Okan Sahin <okan.sahin@analog.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The 104-DIO-48E features an 8254 Counter/Timer chip providing three
counter/timers which can be used for frequency measurement, frequency
output, pulse width modulation, pulse width measurement, event count,
etc. The counter/timers use the same addresses as PPI 0 (addresses 0x0
to 0x3), so a raw_spinlock_t is used to synchronize operations between
the two regmap mappings to prevent clobbering.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Driver is so simple, yet there was a room for mistakes.
Reduce their appearance in the future by enabling COMPILE_TEST
option.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This can reduce the kernel image size in multiplatform configurations.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is nothing in the driver that requires OF APIs,
make the driver OF independent.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been converted in
the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block
-----BEGIN PGP SIGNATURE-----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=3KNJ
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have two new drivers, some improvements to the core code, lots of
different updates to existing GPIO drivers and some dt-bindings on
top.
There's nothing controversial in here and almost everything has been
in next for more than a week (95% a lot longer than this). The only
thing that has spent less time in next is a new driver so no risk of
regressions.
The single merge pulls in changes that remove all usage of global GPIO
numbers from arch/arm/mach-omap.
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers:
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down
delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been
converted in the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block"
* tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (58 commits)
of: unittest: drop assertions for GPIO hog messages
gpiolib: Drop unused domain_ops memeber of GPIO IRQ chip
gpio: synq: remove unused zynq_gpio_irq_reqres/zynq_gpio_irq_relres
dt-bindings: gpio: gpio-vf610: Add parsing of hogs
gpio: lpc18xx: Remove unused of_gpio.h inclusion
gpio: xra1403: Remove unused of_gpio.h inclusion
gpio: mpc8xxx: Remove unused of_gpio.h inclusion
dt-bindings: gpio: Add Cirrus EP93xx
gpio: mpc8xxx: latch GPIOs state on module load when configured as output
selftests: gpio: gpio-sim: Use same variable name for sysfs pathname
gpio: mlxbf3: Add gpio driver support
gpio: delay: Remove duplicative functionality
gpio: aggregator: Set up a parser of delay line parameters
gpio: aggregator: Support delay for setting up individual GPIOs
gpio: aggregator: Remove CONFIG_OF and of_match_ptr() protections
dt-bindings: gpio: pca9570: add gpio-line-names property
gpiolib: remove unused gpio_cansleep()
gpio: tps65219: add GPIO support for TPS65219 PMIC
gpio: zynq: fix zynqmp_gpio not an immutable chip warning
gpio: davinci: make davinci_gpio_dev_pm_ops static
...
Add support for the BlueField-3 SoC GPIO driver.
This driver configures and handles GPIO interrupts. It also enables a user
to manipulate certain GPIO pins via libgpiod tools or other kernel drivers.
The usables pins are defined via the "gpio-reserved-ranges" property.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that GPIO aggregator supports a delay line, drop the duplicative
functionality, i.e. the entire gpio-delay driver.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for TPS65219 PMICs GPIO interface.
3 GPIO pins:
- GPIO0 only is IO but input mode reserved for MULTI_DEVICE_ENABLE usage.
- GPIO1 and GPIO2 are Output only and referred as GPO1 and GPO2 in spec.
GPIO0 is statically configured as input or output prior to Linux boot.
it is used for MULTI_DEVICE_ENABLE function.
This setting is statically configured by NVM.
GPIO0 can't be used as a generic GPIO (specification Table 8-34).
It's either a GPO when MULTI_DEVICE_EN=0 or a GPI when MULTI_DEVICE_EN=1.
Datasheet describes specific usage for non standard GPIO.
Datasheet: https://www.ti.com/lit/ds/symlink/tps65219.pdf
Co-developed-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
