The aoe driver will never be waiting for more than aoe_maxout AoE
commands from a given remote network port on an AoE target. Increasing
the cap increases performance. Users can tighten the setting to reduce
the amount of memory used for handling AoE traffic or the network
bandwidth used for AoE.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before the aoe driver was an I/O request handler, it was a
make_request-style block driver. Even so, there was a problem where
sysfs expected a request queue to exist, so one was provided in commit
7135a71b19be ("aoe: allocate unused request_queue for sysfs").
During the transition to the request-handler style, a patch was merged
that was based on a driver without the noop queue, and the noop queue
remained in place after the patch was merged, even though a new
functional queue was introduced by the patch, allocated through
blk_init_queue.
The user impact is a memory leak proportional to the number of AoE
targets discovered. This patch removes the memory leak and cleans up
vestiges of the old do-nothing queue from the aoeblk_gdalloc function.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f3b8e07af774 ("aoe: commands in retransmit queue use new
destination on failure") omits the copying of the coarse-grained time
when an AoE command was sent during the failover from one destination
MAC address on the AoE target to another.
The coarse-grained timing is only used when the system time changes or
an unlikely length of time has passed since the sending of the AoE
command. Users will not be impacted unless their system clock is very
inaccurate or something unusual (e.g., 10 GbE link reset) happens during
the period when the aoe driver is handling the failure of a port on the
AoE target. Being effected will mean that an AoE target could be
considered "down" too eagerly.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When one remote MAC address isn't working as a destination for AoE
commands, the frames used to track information associated with the AoE
commands are moved to a new aoetgt (defined by the tuple of {AoE major,
AoE minor, target MAC address}).
This patch makes sure that the frames on the queue for retransmits that
need to be done are updated to use the new destination, so that
retransmits will be sent through a working network path.
Without this change, packets on the retransmit queue will be needlessly
retransmitted to the unresponsive destination MAC, possibly causing
premature target failure before there's time for the retransmit timer to
run again, decide to retransmit again, and finally update the destination
to a working MAC address on the AoE target.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes improve the accuracy of the decision about whether it's time
to retransmit an AoE command by using the microsecond-resolution
gettimeofday instead of jiffies.
Because the system time can jump suddenly, the decision reverts to using
jiffies if the high-resolution time difference is relatively large.
Otherwise the AoE targets could be considered failed inappropriately.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this bugfix in place the calculation of the criterion for "lateness"
is performed under lock. Without the lock, there is a chance that one of
the non-atomic operations performed on the round trip time statistics
could be incomplete, such that an incorrect lateness criterion would be
calculated.
Without this change, the effect of the bug would be rare unecessary but
benign retransmissions.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The /dev/etherd/err character device provides low-level information about
normal but sometimes interesting AoE command retransmits and "unexpected
responses", i.e., responses for packets that have already been
retransmitted.
This change adds MAC addresses to the messages about unexpected responses,
so that when they occur, it's more easy to determine the network paths to
which they belong.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoe driver already had some congestion handling, but it was limited in
its ability to cope with the kind of congestion that can arise on more
complex networks such as those involving paths through multiple ethernet
switches.
Some of the lessons from TCP's history of development can be applied to
improving the congestion control and avoidance on AoE storage networks.
These changes use familar concepts from Van Jacobson's "Congestion
Avoidance and Control" paper from '88, without adding significant
overhead.
This patch depends on an upcoming patch that covers the failover case when
AoE commands being retransmitted are transferred from one retransmit queue
to another. Another upcoming patch increases the timing accuracy.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the aoe driver follow expected behavior when the user uses ioctl to
get the ATA device identify information, allowing access to model, serial
number, etc.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The userland aoetools package includes an "aoe-stat" command that can
display a "payload size" column when the aoe driver exports this
information. Users can quickly see what amount of user data is
transferred inside each AoE command on the network, network headers
excluded.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GPFS filesystem is an example of an aoe user that requires the aoe
driver to support I/O request sizes larger than the default. Most users
will not need large I/O request sizes, because they would need to be split
up into multiple AoE commands anyway.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users sometimes want to cause the aoe driver to forget a particular
previously discovered device when it is no longer online. The aoetools
provide an "aoe-flush" command that users run to perform this
administrative task. The changes below provide the support needed in the
driver.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ATA over Ethernet config query response contains a "buffer count"
field reflecting the AoE target's capacity to buffer incoming AoE
commands.
By taking the current value of this field into accound, we increase
performance throughput or avoid network congestion, when the value
has increased or decreased, respectively.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dropped transmits are not common, but when they do occur, increasing
the transmit queue length often helps.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A driver for the DA9055 PMIC. This has a dependency upon the DA9055 MFD
core.
Functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This eliminates having an #ifdef returning NULL for the case when OF is
disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enabling RTC HW block depends on the default value of TPS65910 register.
In some mode, RTC block is disabled by default.(eg. AM3517 Craneboard) In
this case, RTC_PWDN(RTC power down) bit should be cleared to enable the
RTC HW block.
This patch also works in case that RTC block is active by default, because
there is no side effect even if the bit is updated again.
Tested on AM3517 Craneboard.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Sivaram Nair <sivaramn@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code is under #if 0 and not used.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc-s3c driver is modified to use devm_request_and_ioremap() (combining
request_mem_region and ioremap), devm_clk_get() and devm_request_irq()
APIs. Since this removes the necessity of freeing the related resources
the return path is also simplified.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
err_nores label redirects to a simple return statement. Move the return
statement to caller location and remove the label.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an RTC driver for PCF8523 chips by NXP Semiconductors. No support is
currently provided for the alarm and interrupt functions. Only the time
and date functionality is implemented.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_kzalloc() and remove the error path free and the unload free as
devm functions take care of freeing resources.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc_device_register() returns a pointer containing error code in case
of error. Use that in the error return.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A cosmetic change to rename the irq name to match the device name.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The applications can set the RTC hardware to trigger interrupts in one
of three modes:
* AIE: Alarm interrupt
* UIE: Update interrupt (ie: once per second)
* PIE: Periodic interrupt (sub-second irqs)
The above defined 3 modes are to be supported in the RTC HW in form of
interrupts. The SPEAr RTC hardware does not support the later two modes.
There have been refinements in the RTC core in mainline related to
use of timer queue infrastructure to manage events in RTC. Please refer
the below mentioned patch for details:
* RTC: Rework RTC code to use timerqueue for events
* SHA ID: 6610e0893b8bc6f59b14fed7f089c5997f035f88
There have been provisions added to support hardware that do not have
support the UIE mode. Please refer the following patch.
* rtc: Provide flag for rtc devices that don't support UIE
* SHA ID: 4a649903f91232d02284d53724b0a45728111767
The patch makes use of the provision defined in the above patch to
update the hardware status of UIE mode.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clk_{un}prepare is mandatory for platforms using common clock framework.
Because for SPEAr we don't do anything in clk_{un}prepare() calls, just
call them once in probe/remove.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Free the rtc-spear driver from tension of freeing resources :) devm_*
derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Deepak Sikri <deepak.sikri@st.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of error, test_init() needs to call platform_device_del() instead
of platform_device_unregister(). Otherwise, we may call
platform_device_put() twice.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
[akpm@linux-foundation.org: improve label naming]
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add device tree support to the rtc-imxdi driver.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable support for i.MX53 in addition to i.MX25 by enabling the driver on
ARCH_MXC generally.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP1 RTC driver is used in multiple devices like, OMAPL138 and AM33XX.
Driver currently doesn't handle any clocks, which may be right for OMAP1
architecture but in case of AM33XX, the clock/module needs to be enabled
in order to access the registers.
So convert this driver to runtime pm, which internally handles rest.
[afzal@ti.com: handle error path]
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc-omap driver can be reused for AM33xx RTC. Provide dependency in
Kconfig.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enhance rtc-omap driver with DT capability
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP RTC IP can have kicker feature. This prevents spurious writes to
register. To write to registers kicker lock has to be released.
Procedure to do it as follows,
1. write to kick0 register, 0x83e70b13
2. write to kick1 register, 0x95a4f1e0
Writing value other than 0x83e70b13 to kick0 enables write locking, more
details about kicker mechanism can be found in section 20.3.3.5.3 of
AM335X TRM @www.ti.com/am335x
Here id table information is added and is used to distinguish those that
require kicker handling and the ones that doesn't need it. There are more
features in the newer IP's compared to legacy ones other than kicker,
which driver currently doesn't handle, supporting additional features
would be easier with the addition of id table.
Older IP (of OMAP1) doesn't have revision register as per TRM, so revision
register can't be relied always to find features, hence id table is being
used.
While at it, replace __raw_writeb/__raw_readb with writeb/readb; this
driver is used on ARMv7 (AM335X SoC)
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changing backlight intensity on an Akita (Sharp Zaurus C-1000) triggers
WARN_ON message:
WARNING: at drivers/gpio/gpiolib.c:1672 __gpio_set_value+0x38/0xa4()
Modules linked in:
Backtrace:
corgi_bl_set_intensity+0x0/0x74
corgi_bl_update_status+0x0/0x64
corgi_lcd_probe+0x0/0x258
spi_drv_probe+0x0/0x24
driver_probe_device+0x0/0x208
__driver_attach+0x0/0x94
bus_for_each_dev+0x0/0x90
driver_attach+0x0/0x28
bus_add_driver+0x0/0x22c
driver_register+0x0/0x134
spi_register_driver+0x0/0x60
corgi_lcd_driver_init+0x0/0x1c
do_one_initcall+0x0/0x174
kernel_init+0x0/0x2a8
Akita machines have backlight controls hooked to a gpio expander chip,
max7310 using i2c transfers which can sleep. In this case,
pca953x_gpio_set_value() can be called to control gpio, and
pca953x_setup_gpio() sets can_sleep flag. Therefore,
gpio_set_value_cansleep() should be used in order to avoid WARN_ON on
akita machines.
Akita is the only exception in this case since other users of corgi_lcd
access backlight gpio controls through a different gpio expander which
does not set the can_sleep flag.
Signed-off-by: Marko Katic <dromede@gmail.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GPIOF_DIR_OUT and GPIOF_DIR_IN are defined as below:
GPIOF_DIR_OUT (0 << 0)
GPIOF_DIR_IN (1 << 0)
So, when !pdata->reset_inverted is 1, the gpio pin can be set as
input, instead of output.
To prevent this problem, GPIOF_INIT flag should be used when using
devm_gpio_request_one().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, when ops functions cannot be called, lcd_show_contrast() and
lcd_store_contrast() returned 0, instead of ENXIO.
Thus, in this case, a local variable 'rc' for return value should be
initialized as ENXIO, after kstrtoul() is called.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove an unnecessary line continuation in pm860x_backlight_probe().
Also, a checkpatch warning is fixed as below:
WARNING: Avoid unnecessary line continuations
[akpm@linux-foundation.org: remove newline]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TWL_MODULE_PWM is defined as:
#define TWL_MODULE_PWM TWL4030_MODULE_PWM0
Use the common module ID define here which will facilitate the upcoming
twl-core cleanup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function finds the struct backlight_device for a given device tree
node. A dummy function is provided so that it safely compiles out if OF
support is disabled.
[akpm@linux-foundation.org: Don't use IS_ENABLED(CONFIG_OF)]
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need the sysfs file to be world writable or group writable.
This file is write-only, change it to S_IWUSR (0200).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: "G.Shark Jeong" <gshark.jeong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devm_kfree() allocates memory that is released when a driver detaches.
Thus, there is no reason to explicitly call devm_kfree in probe or remove
functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devm_kfree() allocates memory that is released when a driver detaches.
Thus, there is no reason to explicitly call devm_kfree() in probe or remove
functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
