Add code to program the flatiron internal i2c ADC and pass the
appropriate audio mux enums to the cx25840 driver.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The change effects cx23885 boards only and preserves support for existing
boards. Essentially, if we're using baseband audio into the cx23885 AV
core then we have to patch registers. The cx23885 driver will call
with either CX25840_AUDIO8 to signify tuner audio or AUDIO7 to
signify baseband audio. If/When we become more comfortable with this change
across a series of products then we may decide to relax the cx23885 only
restriction.
[liplianin@netup.ru: fix missing state declaration]
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Coding style and printk's cleaned up in following patches.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change is probably good for other boards also, but the change
has limited scope and is reasonably safe.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Coding style and printk's are cleaned up in subsequent patches
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A handlful of coding style issue cleaned up in the following patches.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_g_tuner should not do any memset for the parameters. Core
already does that. In particular, V4L2 core now does some handling
for the tuner type, and the tuner-core module relies on that.
So, doing any memset there is a very bad idea.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[stoth@kernellabs.com: add it to the makefile and fix snd_card binding]
[liplianin@netup.ru: videobuf: Remove the videobuf_sg_dma_map/unmap functions]
Signed-off-by: Mijhail Moreyra <mijhail.moreyra@gmail.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stb0899_status stb0899_check_data the first read of STB0899_VSTATUS
could read old (from previous search) LOOP status bit and the search
fails on a good frequency.
With the patch more transponder could be locked and locks about 2*
faster.
Signed-off-by: Lutz Sammer<johns98@gmx.net>
Reviewed-by: Manu Abraham<manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code here treated user pointers correctly, but the __user tags
weren't used correctly so it caused Sparse warnings:
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the tuner is constantly powered causing these effects.
1. Remembering last tune channel causing corruptions of changing channel.
2. Causing corruption on other frontend.
3. Higher current in standby of demodulator with clock running.
Power sequence now follows;
Power Up
Tuner on -> Frontend suspend off -> Tuner clk on
Power Down
Frontend suspend on -> Tuner clk off -> Tuner off
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tvp5150 video decoder has two operation modes to configure the video
standard used.
If auto-switch mode is enable, the device can sense the signal and detect which
video standard the device is operating. Also the device can be forced to use a
user defined video standard.
Each operation mode uses a different register and the bitmask values to
represent each standard is different.
So we add video standard constants for both autoswitch and no-autoswitch mode.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both mt9t001.c and mt9p031.c have two identical issues, those
being that they will need module.h inclusion for the upcoming
cleanup going on there, and that their dependencies don't limit
selection of configs that will fail to compile as follows:
The related config options are CONFIG_MEDIA_CONTROLLER and
CONFIG_VIDEO_V4L2_SUBDEV_API. Looking at the code, it appears
that the driver was never intended to work without these enabled,
so add a dependency on CONFIG_VIDEO_V4L2_SUBDEV_API, which in
turn already has a dependency on CONFIG_MEDIA_CONTROLLER.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As msp3400 allows standards detection, add support for it. That
efectivelly means that devices with msp3400 can now implement
VIDIOC_QUERYSTD, and it will provide very good detection for
the standard, specially if combined with a video decoder detection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using V4L2_STD_ALL when no standard is detected,
trust that the maximum allowed standards are already filled by
the V4L2 core. It is better this way, as the bridge and/or the audio
decoder may have some extra restrictions to some video standards.
This also allow other devices like audio and tuners to contribute to
standards detection, when they support such feature.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with the V4L2 API spec:
"When detection is not possible or fails, the set must contain
all standards supported by the current video input or output."
The V4L2 core has the mask with all supported standards already. So,
apply it. Driver and subdevs can then just remove standards from the
mask, as they're able of detecting audio, video and frames frequency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several bugs at saa7115 standards detection:
After the fix, the driver is returning the proper standards,
as tested with 3 different broadcast sources:
On an invalid channel (without any TV signal):
[ 4394.931630] saa7115 15-0021: Status byte 2 (0x1f)=0xe0
[ 4394.931635] saa7115 15-0021: detected std mask = 00ffffff
With a PAL/M signal:
[ 4410.836855] saa7115 15-0021: Status byte 2 (0x1f)=0xb1
[ 4410.837727] saa7115 15-0021: Status byte 1 (0x1e)=0x82
[ 4410.837731] saa7115 15-0021: detected std mask = 00000900
With a NTSC/M signal:
[ 4422.383893] saa7115 15-0021: Status byte 2 (0x1f)=0xb1
[ 4422.384768] saa7115 15-0021: Status byte 1 (0x1e)=0x81
[ 4422.384772] saa7115 15-0021: detected std mask = 0000b000
Tests were done with a WinTV PVR USB2 Model 29xx card.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.
Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.
Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.
Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.
Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This lock should be released as well on the error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Patrick Boettcher <Patrick.Boettcher@dibcom.fr>
Cc: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Negate has higher precedence than bitwise AND. I2C_M_RD is 0x1 so
the original code is equivelent to just checking if (!msg->flags).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.
This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These are necessary to prevent dead-locks e.g. if one thread waits
in dqbuf at one end and another tries to queue a buffer at the
other end.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Pawel Osciak <pawel@osciak.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes mbus configuration between Mixer, SDO and HDMI. The SDO
accepts only YUV444 on input. The HDMI in DVI mode accepts only RGB888. Now
Mixer is choosing proper output format depending on mbus format.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Current version of the driver does not support HDMI features
not present in DVI standard. Therefore DVI mode is used to
keep compatibility with DVI devices.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The TVOUT driver requires PM_RUNTIME support for proper clock
enabling.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplifies the locking by moving the em28xx_init_extension() call until
em28xx_usb_probe() has finished with the dev->lock mutex. It therefore
makes the second and subsequent "plugging" events logically identical to
the first "plugging" event when the em28xx-dvb and em28xx-alsa modules
must be loaded (i.e. registered).
Basically, em28xx_usb_probe() requests that em28xx-dvb be loaded and
also triggers udev to initialise the V4L2 devices. These two events are
serialised by the dev->lock mutex but the order that they happen in is
undefined. But this has always been the case anyway.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
