If macsec is offloaded, we need to follow the lower device's
capabilities, like VLAN devices do.
Leave the limits unchanged when the offload is disabled.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/8240c0181e851f169d815f59658a01fb9dfc5073.1730929545.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit extends the set of netdevice features supported by macsec
devices when offload is enabled, which increases performance
significantly (for a single TCP stream: 17.5Gbps to 38.5Gbps on my
test machines).
Commit c850240b6c ("net: macsec: report real_dev features when HW
offloading is enabled") previously attempted something similar, but
had to be reverted (commit 8bcd560ae8 ("Revert "net: macsec: report
real_dev features when HW offloading is enabled"")) because the set of
features it exposed was too large.
During initialization, all features are set, and they're then removed
via ndo_fix_features (macsec_fix_features). This allows the
offloadable features to be automatically enabled if offloading is
turned on after device creation.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/8b32c3011d269d6f149724e80c1ffe67c9534067.1730929545.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the original conversion is from the spatch below,
but I edited some and left out other instances that were
either buggy after conversion (where default values don't
fit into the type) or just looked strange.
@@
expression attr, def;
expression val;
identifier fn =~ "^nla_get_.*";
fresh identifier dfn = fn ## "_default";
@@
(
-if (attr)
- val = fn(attr);
-else
- val = def;
+val = dfn(attr, def);
|
-if (!attr)
- val = def;
-else
- val = fn(attr);
+val = dfn(attr, def);
|
-if (!attr)
- return def;
-return fn(attr);
+return dfn(attr, def);
|
-attr ? fn(attr) : def
+dfn(attr, def)
|
-!attr ? def : fn(attr)
+dfn(attr, def)
)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@kernel.org>
Link: https://patch.msgid.link/20241108114145.0580b8684e7f.I740beeaa2f70ebfc19bfca1045a24d6151992790@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KASAN reports the following UAF. The metadata_dst, which is used to
store the SCI value for macsec offload, is already freed by
metadata_dst_free() in macsec_free_netdev(), while driver still use it
for sending the packet.
To fix this issue, dst_release() is used instead to release
metadata_dst. So it is not freed instantly in macsec_free_netdev() if
still referenced by skb.
BUG: KASAN: slab-use-after-free in mlx5e_xmit+0x1e8f/0x4190 [mlx5_core]
Read of size 2 at addr ffff88813e42e038 by task kworker/7:2/714
[...]
Workqueue: mld mld_ifc_work
Call Trace:
<TASK>
dump_stack_lvl+0x51/0x60
print_report+0xc1/0x600
kasan_report+0xab/0xe0
mlx5e_xmit+0x1e8f/0x4190 [mlx5_core]
dev_hard_start_xmit+0x120/0x530
sch_direct_xmit+0x149/0x11e0
__qdisc_run+0x3ad/0x1730
__dev_queue_xmit+0x1196/0x2ed0
vlan_dev_hard_start_xmit+0x32e/0x510 [8021q]
dev_hard_start_xmit+0x120/0x530
__dev_queue_xmit+0x14a7/0x2ed0
macsec_start_xmit+0x13e9/0x2340
dev_hard_start_xmit+0x120/0x530
__dev_queue_xmit+0x14a7/0x2ed0
ip6_finish_output2+0x923/0x1a70
ip6_finish_output+0x2d7/0x970
ip6_output+0x1ce/0x3a0
NF_HOOK.constprop.0+0x15f/0x190
mld_sendpack+0x59a/0xbd0
mld_ifc_work+0x48a/0xa80
process_one_work+0x5aa/0xe50
worker_thread+0x79c/0x1290
kthread+0x28f/0x350
ret_from_fork+0x2d/0x70
ret_from_fork_asm+0x11/0x20
</TASK>
Allocated by task 3922:
kasan_save_stack+0x20/0x40
kasan_save_track+0x10/0x30
__kasan_kmalloc+0x77/0x90
__kmalloc_noprof+0x188/0x400
metadata_dst_alloc+0x1f/0x4e0
macsec_newlink+0x914/0x1410
__rtnl_newlink+0xe08/0x15b0
rtnl_newlink+0x5f/0x90
rtnetlink_rcv_msg+0x667/0xa80
netlink_rcv_skb+0x12c/0x360
netlink_unicast+0x551/0x770
netlink_sendmsg+0x72d/0xbd0
__sock_sendmsg+0xc5/0x190
____sys_sendmsg+0x52e/0x6a0
___sys_sendmsg+0xeb/0x170
__sys_sendmsg+0xb5/0x140
do_syscall_64+0x4c/0x100
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Freed by task 4011:
kasan_save_stack+0x20/0x40
kasan_save_track+0x10/0x30
kasan_save_free_info+0x37/0x50
poison_slab_object+0x10c/0x190
__kasan_slab_free+0x11/0x30
kfree+0xe0/0x290
macsec_free_netdev+0x3f/0x140
netdev_run_todo+0x450/0xc70
rtnetlink_rcv_msg+0x66f/0xa80
netlink_rcv_skb+0x12c/0x360
netlink_unicast+0x551/0x770
netlink_sendmsg+0x72d/0xbd0
__sock_sendmsg+0xc5/0x190
____sys_sendmsg+0x52e/0x6a0
___sys_sendmsg+0xeb/0x170
__sys_sendmsg+0xb5/0x140
do_syscall_64+0x4c/0x100
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fixes: 0a28bfd497 ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20241021100309.234125-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On RX, we shouldn't be incrementing the stats for an arbitrary SA in
case the actual SA hasn't been set up. Those counters are intended to
track packets for their respective AN when the SA isn't currently
configured. Due to the way MACsec is implemented, we don't keep
counters unless the SA is configured, so we can't track those packets,
and those counters will remain at 0.
The RXSC's stats keeps track of those packets without telling us which
AN they belonged to. We could add counters for non-existent SAs, and
then find a way to integrate them in the dump to userspace, but I
don't think it's worth the effort.
Fixes: 91ec9bd57f ("macsec: Fix traffic counters/statistics")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/f5ac92aaa5b89343232615f4c03f9f95042c6aa0.1728657709.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NETIF_F_LLTX can't be changed via Ethtool and is not a feature,
rather an attribute, very similar to IFF_NO_QUEUE (and hot).
Free one netdev_features_t bit and make it a "hot" private flag.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Can now correctly identify where the packets should be delivered by using
md_dst or its absence on devices that provide it.
This detection is not possible without device drivers that update md_dst. A
fallback pattern should be used for supporting such device drivers. This
fallback mode causes multicast messages to be cloned to both the non-macsec
and macsec ports, independent of whether the multicast message received was
encrypted over MACsec or not. Other non-macsec traffic may also fail to be
handled correctly for devices in promiscuous mode.
Link: https://lore.kernel.org/netdev/ZULRxX9eIbFiVi7v@hog/
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: stable@vger.kernel.org
Fixes: 860ead89b8 ("net/macsec: Add MACsec skb_metadata_dst Rx Data path support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240423181319.115860-4-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the macsec driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240305113728.1974944-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
This patch prepares dev_get_iflink() and nla_put_iflink()
to run either with RTNL or RCU held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading MACsec in PHYs requires inserting the SecTAG and the ICV in
the ethernet frame. This operation will increase the frame size with up
to 32 bytes. If the frames are sent at line rate, the PHY will not have
enough room to insert the SecTAG and the ICV.
Some PHYs use a hardware buffer to store a number of ethernet frames and,
if it fills up, a pause frame is sent to the MAC to control the flow.
This HW implementation does not need any modification in the stack.
Other PHYs might offer to use a specific ethertype with some padding
bytes present in the ethernet frame. This ethertype and its associated
bytes will be replaced by the SecTAG and ICV.
mdo_insert_tx_tag allows the PHY drivers to add any specific tag in the
skb.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the MAC address if mdo_upd_secy fails. Offloaded MACsec device
might be left in an inconsistent state.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_ensure_writable_head_tail to expand the skb if needed instead of
reimplementing a similar operation.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
kernel/bpf/verifier.c
829955981c ("bpf: Fix verifier log for async callback return values")
a923819fb2 ("bpf: Treat first argument as return value for bpf_throw")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Indicate next PN update using update_pn flag in macsec_context.
Offloaded MACsec implementations does not know whether or not the
MACSEC_SA_ATTR_PN attribute was passed for an SA update and assume
that next PN should always updated, but this is not always true.
The PN can be reset to its initial value using the following command:
$ ip macsec set macsec0 tx sa 0 off #octeontx2-pf case
Or, the update PN command will succeed even if the driver does not support
PN updates.
$ ip macsec set macsec0 tx sa 0 pn 1 on #mscc phy driver case
Comparing the initial PN with the new PN value is not a solution. When
the user updates the PN using its initial value the command will
succeed, even if the driver does not support it. Like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 on #mlx5 case
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Companion of DEV_STATS_INC() & DEV_STATS_ADD().
This is going to be used in the series.
Use it in macsec_get_stats64().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
mlx5 MACsec RoCEv2 support
From Patrisious:
This series extends previously added MACsec offload support
to cover RoCE traffic either.
In order to achieve that, we need configure MACsec with offload between
the two endpoints, like below:
REMOTE_MAC=10:70:fd:43:71:c0
* ip addr add 1.1.1.1/16 dev eth2
* ip link set dev eth2 up
* ip link add link eth2 macsec0 type macsec encrypt on
* ip macsec offload macsec0 mac
* ip macsec add macsec0 tx sa 0 pn 1 on key 00 dffafc8d7b9a43d5b9a3dfbbf6a30c16
* ip macsec add macsec0 rx port 1 address $REMOTE_MAC
* ip macsec add macsec0 rx port 1 address $REMOTE_MAC sa 0 pn 1 on key 01 ead3664f508eb06c40ac7104cdae4ce5
* ip addr add 10.1.0.1/16 dev macsec0
* ip link set dev macsec0 up
And in a similar manner on the other machine, while noting the keys order
would be reversed and the MAC address of the other machine.
RDMA traffic is separated through relevant GID entries and in case
of IP ambiguity issue - meaning we have a physical GIDs and a MACsec
GIDs with the same IP/GID, we disable our physical GID in order
to force the user to only use the MACsec GID.
v0: https://lore.kernel.org/netdev/20230813064703.574082-1-leon@kernel.org/
* 'mlx5-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
RDMA/mlx5: Handles RoCE MACsec steering rules addition and deletion
net/mlx5: Add RoCE MACsec steering infrastructure in core
net/mlx5: Configure MACsec steering for ingress RoCEv2 traffic
net/mlx5: Configure MACsec steering for egress RoCEv2 traffic
IB/core: Reorder GID delete code for RoCE
net/mlx5: Add MACsec priorities in RDMA namespaces
RDMA/mlx5: Implement MACsec gid addition and deletion
net/mlx5: Maintain fs_id xarray per MACsec device inside macsec steering
net/mlx5: Remove netdevice from MACsec steering
net/mlx5e: Move MACsec flow steering and statistics database from ethernet to core
net/mlx5e: Rename MACsec flow steering functions/parameters to suit core naming style
net/mlx5: Remove dependency of macsec flow steering on ethernet
net/mlx5e: Move MACsec flow steering operations to be used as core library
macsec: add functions to get macsec real netdevice and check offload
====================
Link: https://lore.kernel.org/r/20230821073833.59042-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Given a macsec net_device add two functions to return the real net_device
for that device, and check if that macsec device is offloaded or not.
This is needed for auxiliary drivers that implement MACsec offload, but
have flows which are triggered over the macsec net_device, this allows
the drivers in such cases to verify if the device is offloaded or not,
and to access the real device of that macsec device, which would
belong to the driver, and would be needed for the offload procedure.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Use the helper functions dev_sw_netstats_rx_add() and
dev_sw_netstats_tx_add() to update stats, which helps to
provide code readability.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot/KCSAN reported data-races in macsec whenever dev->stats fields
are updated.
It appears all of these updates can happen from multiple cpus.
Adopt SMP safe DEV_STATS_INC() to update dev->stats fields.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside macsec_add_dev() we free percpu macsec->secy.tx_sc.stats and
macsec->stats on some of the memory allocation failure paths. However, the
net_device is already registered to that moment: in macsec_newlink(), just
before calling macsec_add_dev(). This means that during unregister process
its priv_destructor - macsec_free_netdev() - will be called and will free
the stats again.
Remove freeing percpu stats inside macsec_add_dev() because
macsec_free_netdev() will correctly free the already allocated ones. The
pointers to unallocated stats stay NULL, and free_percpu() treats that
correctly.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 0a28bfd497 ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support")
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading device drivers will mark offloaded MACsec SKBs with the
corresponding SCI in the skb_metadata_dst so the macsec rx handler will
know to which interface to divert those skbs, in case of a marked skb
and a mismatch on the dst MAC address, divert the skb to the macsec
net_device where the macsec rx_handler will be called to consider cases
where relying solely on the dst MAC address is insufficient.
One such instance is when using MACsec with a VLAN as an inner
header, where the packet structure is ETHERNET | SECTAG | VLAN.
In such a scenario, the dst MAC address in the ethernet header
will correspond to the VLAN MAC address, resulting in a mismatch.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core
----
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used
to describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols
---------
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP
path manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF
---
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key
to better support decap on GRE tunnel devices not operating
in collect metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk
and bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols
by livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter
---------
- Remove the CLUSTERIP target. It has been marked as obsolete
for years, and we still have WARN splats wrt. races of
the out-of-band /proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to
the existing 'delete' commands, but do not return an error if
the referenced object (set, chain, rule...) did not exist.
Driver API
----------
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into multiple
files, drop some of the unnecessarily granular locks and factor out
common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless Extensions
for Wi-Fi 7 devices at all. Everyone should switch to using nl80211
interface instead.
- Improve the CAN bit timing configuration. Use extack to return error
messages directly to user space, update the SJW handling, including
the definition of a new default value that will benefit CAN-FD
controllers, by increasing their oscillator tolerance.
New hardware / drivers
----------------------
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers
-------
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- enetc: support XDP_REDIRECT for XDP non-linear buffers
- enetc: improve reconfig, avoid link flap and waiting for idle
- enetc: support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q, 8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmP1VIYACgkQMUZtbf5S
IrvsChAApz0rNL/sPKxXTEfxZ1tN7D3sYxYKQPomxvl5BV+MvicrLddJy3KmzEFK
nnJNO3nuRNuH422JQ/ylZ4mGX1opa6+5QJb0UINImXUI7Fm8HHBIuPGkv7d5CheZ
7JexFqjPJXUy9nPyh1Rra+IA9AcRd2U7jeGEZR38wb99bHJQj5Bzdk20WArEB0el
n44aqg49LXH71bSeXRz77x5SjkwVtYiccQxLcnmTbjLU2xVraLvI2J+wAhHnVXWW
9lrU1+V4Ex2Xcd1xR0L0cHeK+meP1TrPRAeF+JDpVI3a/zJiE7cZjfHdG/jH5xWl
leZJqghVozrZQNtewWWO7XhUFhMDgFu3W/1vNLjSHPZEqaz1JpM67J1+ql6s63l4
LMWoXbcYZz+SL9ZRCoPkbGue/5fKSHv8/Jl9Sh58+eTS+c/zgN8uFGRNFXLX1+EP
n8uvt985PxMd6x1+dHumhOUzxnY4Sfi1vjitSunTsNFQ3Cmp4SO0IfBVJWfLUCuC
xz5hbJGJJbSpvUsO+HWyCg83E5OWghRE/Onpt2jsQSZCrO9HDg4FRTEf3WAMgaqc
edb5KfbRZPTJQM08gWdluXzSk1nw3FNP2tXW4XlgUrEbjb+fOk0V9dQg2gyYTxQ1
Nhvn8ZQPi6/GMMELHAIPGmmW1allyOGiAzGlQsv8EmL+OFM6WDI=
=xXhC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used to
describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on
boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols:
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF:
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
better support decap on GRE tunnel devices not operating in collect
metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk and
bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols by
livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter:
- Remove the CLUSTERIP target. It has been marked as obsolete for
years, and we still have WARN splats wrt races of the out-of-band
/proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to the
existing 'delete' commands, but do not return an error if the
referenced object (set, chain, rule...) did not exist.
Driver API:
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into
multiple files, drop some of the unnecessarily granular locks and
factor out common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless
Extensions for Wi-Fi 7 devices at all. Everyone should switch to
using nl80211 interface instead.
- Improve the CAN bit timing configuration. Use extack to return
error messages directly to user space, update the SJW handling,
including the definition of a new default value that will benefit
CAN-FD controllers, by increasing their oscillator tolerance.
New hardware / drivers:
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers:
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- support XDP_REDIRECT for XDP non-linear buffers
- improve reconfig, avoid link flap and waiting for idle
- support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q,
8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation"
* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
page_pool: add a comment explaining the fragment counter usage
net: ethtool: fix __ethtool_dev_mm_supported() implementation
ethtool: pse-pd: Fix double word in comments
xsk: add linux/vmalloc.h to xsk.c
sefltests: netdevsim: wait for devlink instance after netns removal
selftest: fib_tests: Always cleanup before exit
net/mlx5e: Align IPsec ASO result memory to be as required by hardware
net/mlx5e: TC, Set CT miss to the specific ct action instance
net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
net/mlx5: Refactor tc miss handling to a single function
net/mlx5: Kconfig: Make tc offload depend on tc skb extension
net/sched: flower: Support hardware miss to tc action
net/sched: flower: Move filter handle initialization earlier
net/sched: cls_api: Support hardware miss to tc action
net/sched: Rename user cookie and act cookie
sfc: fix builds without CONFIG_RTC_LIB
sfc: clean up some inconsistent indentings
net/mlx4_en: Introduce flexible array to silence overflow warning
net: lan966x: Fix possible deadlock inside PTP
net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
...
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds temporary scaffolding so that the Crypto API
completion function can take a void * instead of crypto_async_request.
Once affected users have been converted this can be removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support dumping offload netlink attribute in macsec's device
attributes dump.
Change macsec_get_size to consider the offload attribute in
the calculations of the required room for dumping the device
netlink attributes.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for changing Macsec offload selection through the
netlink layer by implementing the relevant changes in
macsec_changelink.
Since the handling in macsec_changelink is similar to macsec_upd_offload,
update macsec_upd_offload to use a common helper function to avoid
duplication.
Example for setting offload for a macsec device:
ip link set macsec0 type macsec offload mac
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently macsec offload selection update routine accesses
the net device prior to holding the relevant lock.
Fix by holding the lock prior to the device access.
Fixes: dcb780fb27 ("net: macsec: add nla support for changing the offloading selection")
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Link: https://lore.kernel.org/r/20221211075532.28099-1-ehakim@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing attribute validation for IFLA_MACSEC_OFFLOAD
to the netlink policy.
Fixes: 791bb3fcaf ("net: macsec: add support for specifying offload upon link creation")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20221207101618.989-1-ehakim@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'ret' is defined twice in macsec_changelink(), when it is set in macsec_is_offloaded
case, it will be invalid before return.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20221118011249.48112-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
macsec_add_rxsa and macsec_add_txsa copy the key to an on-stack
offloading context to pass it to the drivers, but leaves it there when
it's done. Clear it with memzero_explicit as soon as it's not needed
anymore.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macsec_is_configured incorrectly uses secy->n_rx_sc to check if some
RXSCs exist. secy->n_rx_sc only counts the number of active RXSCs, but
there can also be inactive SCs as well, which may be stored in the
driver (in case we're disabling offloading), or would have to be
pushed to the device (in case we're trying to enable offloading).
As long as RXSCs active on creation and never turned off, the issue is
not visible.
Fixes: dcb780fb27 ("net: macsec: add nla support for changing the offloading selection")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
secy->n_rx_sc is supposed to be the number of _active_ rxsc's within a
secy. This is then used by macsec_send_sci to help decide if we should
add the SCI to the header or not.
This logic is currently broken when we create a new RXSC and turn it
off at creation, as create_rx_sc always sets ->active to true (and
immediately uses that to increment n_rx_sc), and only later
macsec_add_rxsc sets rx_sc->active.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we get an inconsistent state:
- netlink returns the error to userspace
- the RXSC is installed but not offloaded
Then the device could get confused when we try to add an RXSA, because
the RXSC isn't supposed to exist.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c850240b6c.
That commit tried to improve the performance of macsec offload by
taking advantage of some of the NIC's features, but in doing so, broke
macsec offload when the lower device supports both macsec and ipsec
offload, as the ipsec offload feature flags (mainly NETIF_F_HW_ESP)
were copied from the real device. Since the macsec device doesn't
provide xdo_* ops, the XFRM core rejects the registration of the new
macsec device in xfrm_api_check.
Example perf trace when running
ip link add link eni1np1 type macsec port 4 offload mac
ip 737 [003] 795.477676: probe:xfrm_dev_event__REGISTER name="macsec0" features=0x1c000080014869
xfrm_dev_event+0x3a
notifier_call_chain+0x47
register_netdevice+0x846
macsec_newlink+0x25a
ip 737 [003] 795.477687: probe:xfrm_dev_event__return ret=0x8002 (NOTIFY_BAD)
notifier_call_chain+0x47
register_netdevice+0x846
macsec_newlink+0x25a
dev->features includes NETIF_F_HW_ESP (0x04000000000000), so
xfrm_api_check returns NOTIFY_BAD because we don't have
dev->xfrmdev_ops on the macsec device.
We could probably propagate GSO and a few other features from the
lower device, similar to macvlan. This will be done in a future patch.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 0a28bfd497 added a metadata_dst to each tx_sc, but that's
only allocated when macsec_add_dev has run, which happens after device
registration. If the requested or computed SCI already exists, or if
linking to the lower device fails, we will panic because
metadata_dst_free can't handle NULL.
Reproducer:
ip link add link $lower type macsec
ip link add link $lower type macsec
Fixes: 0a28bfd497 ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/60f2a1965fe553e2cade9472407d0fafff8de8ce.1663923580.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the MACsec offloading preparation phase was removed from the
MACsec core implementation as well as from drivers implementing it, we
can safely remove the flag representing it.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware offloading in MACsec was initially supported using 2 phases.
This was proposed in the RFC as this could have allowed easier fallback
to the software implementation if the hardware did not support a feature
or had enough entries already. But this fallback wasn't implemented and
might not be a good idea after all. In addition it turned out this logic
didn't mapped well the hardware logic and device drivers were mostly
ignoring the preparation phase.
Let's remove this as it does not offer any advantage and is ignored by
drivers.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently macsec invokes HW offload path before reading extended packet
number (EPN) related user properties i.e. salt and short secure channel
identifier (ssci), hence preventing macsec EPN HW offload.
Expose those by moving macsec EPN properties reading prior to HW offload
path.
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move some MACsec infrastructure like defines and functions,
in order to avoid code duplication for future drivers which
implements MACsec offload.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ben Ben-Ishay <benishay@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in the Tx changes, if there are more than one MACsec device with
the same MAC address as in the packet's destination MAC, the packet will
be forward only to this device and not neccessarly to the desired one.
Offloading device drivers will mark offloaded MACsec SKBs with the
corresponding SCI in the skb_metadata_dst so the macsec rx handler will
know to which port to divert those skbs, instead of wrongly solely
relaying on dst MAC address comparison.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current MACsec offload implementation, MACsec interfaces shares
the same MAC address by default.
Therefore, HW can't distinguish from which MACsec interface the traffic
originated from.
MACsec stack will use skb_metadata_dst to store the SCI value, which is
unique per Macsec interface, skb_metadat_dst will be used by the
offloading device driver to associate the SKB with the corresponding
offloaded interface (SCI).
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.
One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.
To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>
