The imx219/imx708 sensors frequently generate a single corrupt frame
(image or embedded data) when the sensor first starts. This can either
be a missing line, or invalid samples within the line. This only occurrs
using the upstream Unicam kernel driver.
Disabling trigger mode elimiates this corruption. Since trigger mode is
a legacy feature copied from the firmware driver and not expected to be
needed, remove it. Tested on the Raspberry Pi cameras and shows no ill
effects.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When matching formats via try_fmt/set_fmt ioctls, test for the unpacked
formats as well as packed formats. This allows userland clients setup
unpacking to 16-bits from the 10/12/14-packed CSI2 formats.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ensure that the frame sequence counter is incremented only if a previous
frame start interrupt has occurred, or a frame start + frame end has
occurred simultaneously.
This corresponds the sequence number with the actual number of frames
produced by the sensor, not the number of frame buffers dequeued back
to userland.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some designs the regulators for the AVDD / DOVDD / DVDD power rails
are controlled by Linux.
Add support to the driver for getting regulators for these 3 rails and
for enabling these regulators when necessary.
The datasheet specifies a delay of 0ns between enabling the regulators,
IOW they can all 3 be enabled at the same time. This allows using the bulk
regulator API.
The regulator core will provide dummy regulators for the 3 power-rails
when necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov2740 sensor has both reset and power_down inputs according to
the datasheet one or the other should always be tied to DOVDD but on
some designs both are attached to GPIOs.
Add support for controlling both a reset and a powerdown GPIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add camera orientation and sensor rotation controls using
the v4l2_fwnode_device_parse() and v4l2_ctrl_new_fwnode_properties()
helpers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Calling the identify function may get delayed till the first stream-on,
add a dev_dbg() to it so that we know when it has run. This is useful
to debug bring-up problems related to regulators / clks / GPIOs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Light frequency was not properly returned when in auto
mode and the detected frequency was 60Hz.
Fixes: 19a81c1426c1 ("[media] add Omnivision OV5640 sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sam Bobrowicz <sam@elite-embedded.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When creating links from a subdev to a sink, the current logic tries to
iterate over the endpoints of dev's fwnode.
This might not be correct when the subdev uses a different fwnode
compared to the dev's fwnode.
If, when registering, the subdev's fwnode is not set, the code inside
v4l2_async_register_subdev will set it to the dev's fwnode.
To fix this, just use the subdev's fwnode.
Signed-off-by: Cosmin Tanislav <demonsingur@gmail.com>
Fixes: 0d3c81e82da9 ("media: v4l2-mc: add v4l2_create_fwnode_links helpers")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix a few cases where a local shadows a previously declared local of the
same name.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add error handling for i2c reads/writes in various places.
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Closes: https://lore.kernel.org/all/Zv40EQSR__JDN_0M@kekkonen.localdomain/
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add error handling to ub913_hw_init() using a new helper function,
ub913_update_bits().
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Closes: https://lore.kernel.org/all/Zv40EQSR__JDN_0M@kekkonen.localdomain/
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We currently sleep for 50 ms at the end of each iteration in
ub960_rxport_wait_locks(). This feels a bit excessive, especially as we
always do at least two loops, so there's always at least one sleep, even
if we already have a stable lock.
Change the sleep to 10 ms.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the unused UB960_IND_TARGET_CSI_CSIPLL_REG_1 define. It does not
even match to any block in the more recent documents, so it's possible
it is not only unused but also wrong.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clear the CRC error counter after showing it in ub953_log_status() to
make its behavior match the other counter values.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add RGB24 and RAW8 and RAW10 bayer formats. RGB24 is mostly for TPG
purposes, but RAW8 and RAW10 are widely used by sensors.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Normally the driver accesses both the RX and the TX port registers via a
paging mechanism: one register is used to select the page (i.e. the
port), which dictates the port used when accessing the port specific
registers.
The downside to this is that while debugging it's almost impossible to
access the port specific registers from the userspace, as the driver can
change the page at any moment.
The hardware supports another access mechanism: using the I2C_RX_ID
registers (one for each RX port), i2c addresses can be chosen which,
when accessed, will always use the specific port's registers, skipping
the paging mechanism.
The support is only for the RX port, but it has proven very handy while
debugging and testing. So let's add the code for this, but hide it
behind a disabled define.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use HZ_PER_MHZ instead of 1000000U.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver uses a static CSI-2 virtual channel mapping where all virtual
channels from an RX port are mapped to a virtual channel number matching
the RX port number.
The UB960 and UB9702 have different registers for the purpose, and the
UB9702 version is not correct. Each of the VC_ID_MAP registers do not
contain a single mapping, as the driver currently thinks, but two.
This can cause received VCs other than 0 to be mapped in a wrong way.
Fix this by writing both mappings to each register.
Cc: stable@vger.kernel.org
Fixes: afe267f2d368 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UB9702 does not have SP and EQ registers, but the driver uses them in
log_status(). Fix this by separating the SP and EQ related log_status()
work into a separate function (for clarity) and calling that function
only for UB960.
Cc: stable@vger.kernel.org
Fixes: afe267f2d368 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UB9702 doesn't have the registers for SP and EQ. Adjust the code in
ub960_rxport_wait_locks() to not use those registers for UB9702. As
these values are only used for a debug print here, there's no functional
change.
Cc: stable@vger.kernel.org
Fixes: afe267f2d368 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UB9702 has the refclk freq register at a different offset than UB960,
but the code uses the UB960's offset for both chips. Fix this.
The refclk freq is only used for a debug print, so there's no functional
change here.
Cc: stable@vger.kernel.org
Fixes: afe267f2d368 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ub913 and ub953 drivers call fwnode_handle_put(priv->sd.fwnode) as
part of their remove process, and if the driver is removed multiple
times, eventually leads to put "overflow", possibly causing memory
corruption or crash.
The fwnode_handle_put() is a leftover from commit 905f88ccebb1 ("media:
i2c: ds90ub9x3: Fix sub-device matching"), which changed the code
related to the sd.fwnode, but missed removing these fwnode_handle_put()
calls.
Cc: stable@vger.kernel.org
Fixes: 905f88ccebb1 ("media: i2c: ds90ub9x3: Fix sub-device matching")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
No need to continue probing when the CCS static data parser fails. Improve
this by checking the return value and correctly exiting on failure.
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Besides returning an error, also print a warning when
ccs_data_parse() fails.
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When ipu6 driver is waiting for the ivsc driver to probe,
which can fail or take long time, we can get plenty of ipu6
messages like this:
[ 15.454049] intel-ipu6 0000:00:05.0: IPU6 in non-secure mode touch 0x0 mask 0xff
[ 15.456600] intel-ipu6 0000:00:05.0: FW version: 20230925
[ 15.458292] intel-ipu6 0000:00:05.0: IPU6 in non-secure mode touch 0x0 mask 0xff
[ 15.461186] intel-ipu6 0000:00:05.0: FW version: 20230925
[ 15.463616] intel-ipu6 0000:00:05.0: IPU6 in non-secure mode touch 0x0 mask 0xff
[ 15.466490] intel-ipu6 0000:00:05.0: FW version: 20230925
Print them only when debugging is enabled to do not flood dmesg.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The latest datasheet (Rev.0.70) updates the D-PHY start-up sequence for
D-PHY operation. Unfortunately the datasheet do not add any additional
documentation on the magic values.
This have been tested together with the MAX96724 available on the single
board test platform and it works as expected.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The datasheet lists that "Maximum exposure time is frame
length -25 row periods, where frame length is set by
registers {0x380E, 0x380F}".
However this driver had OV9282_EXPOSURE_OFFSET set to 12
which allowed that restriction to be violated, and would
result in very under-exposed images.
Correct the offset.
Fixes: 14ea315bbeb7 ("media: i2c: Add ov9282 camera sensor driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ccs_limits is allocated in ccs_read_all_limits() after the allocation of
mdata.backing. Ensure that resources are freed in the reverse order of
their allocation by moving out_free_ccs_limits up.
Fixes: a11d3d6891f0 ("media: ccs: Read CCS static data from firmware binaries")
Cc: stable@vger.kernel.org
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Later versions of the V4H datasheet adds documentation for the line
order register needed to support all possible configurations. Extend the
driver to take the line order for each data line into account when
configuring the device.
Unfortunately not all registers initially thought to be involved in line
order configuration where directly related. One magic value is still in
the driver and left as-is, but it is not related to line order as that
procedure have now been documented.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Extend the fwnode parsing to validate and fill in the CSI-2 C-PHY
line-orders order properties as defined in MIPI Discovery and
Configuration (DisCo) Specification for Imaging.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[Sakari Ailus: Use ARRAY_SIZE() instead of an integer.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a 2-5ms delay when coming out of standby and before reading the
sensor info register durning probe, as instructed by the datasheet. This
standby delay is already present when the sensor starts streaming.
During a cold-boot, reading the IMX296_SENSOR_INFO register would often
return a value of 0x0000, if this delay is not present before.
Fixes: cb33db2b6ccf ("media: i2c: IMX296 camera sensor driver")
Cc: stable@vger.kernel.org
Tested-by: Alexandru Ardelean <aardelean@baylibre.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX462 is the successor to IMX290, and wants very minor
changes to the register setup.
Add the relevant configuration to support it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewing the datasheets, register 0x3011 is meant to be 0x02 on imx327
and 0x00 on imx290.
Move it out of the common registers, and set it appropriately in the
sensor specific sections. (Included for imx290 to be explicit, rather
than relying on the default value).
Fixes: 2d41947ec2c0 ("media: i2c: imx290: Add support for imx327 variant")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The imx327 only supports up to 29.4dB of analogue gain, vs
the imx290 going up to 30dB. Both are in 0.3dB steps.
As we now have model specific config, fix this mismatch,
and delete the comment referencing it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ccs_data_parse() releases the allocated in-memory data structure when the
parser fails, but it does not clean up parsed metadata that is there to
help access the actual data. Do that, in order to return the data
structure in a sane state.
Fixes: a6b396f410b1 ("media: ccs: Add CCS static data parser library")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The length field of the CCS static data blocks was mishandled, leading to
wrong interpretation of the length header for blocks that are 16 kiB in
size. Such large blocks are very, very rare and so this wasn't found
earlier.
As the length is used as part of input validation, the issue has no
security implications.
Fixes: a6b396f410b1 ("media: ccs: Add CCS static data parser library")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add check for the return value of clk_enable() to guarantee the success.
Fixes: 81a409bfd551 ("media: marvell-ccic: provide a clock for the sensor")
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
[Sakari Ailus: Fix spelling in commit message.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The company name has update to Rockchip Electronics Co., Ltd.
since 2021.
And change Co.Ltd to Co., Ltd. to fix mail server warning:
DBL_SPAM(6.50)[co.ltd:url];
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241216100444.3726048-1-andyshrk@163.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Store the chroma and motion vector offsets for each frame so that they
can be used later when the resolution changes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Hantro decoder non post-processed pixel-format steps are different
from the post-processed ones. Fix the steps according to the hardware
limitations. Since reference frame pixel-format issues have been fixed,
it is possible to use V4L2_PIX_FMT_NV15_4L4 rather V4L2_PIX_FMT_P010_4L4
for 10bit streams.
Fluster VP9 score goes up to 207/305.
HEVC score is still 141/147.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Hantro decoder always produces tiled pixel-formats, but when the
post-processor is used, the destination pixel-format is a non-tiled
pixel-format. This causes an incorrect computation of the reference
frame size and offsets. Get and save the correct tiled pixel-format for
8 and 10 bit streams to solve these computation issues.
Fluster VP9 score increase to 166/305 (vs 145/305).
HEVC score is still 141/147.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With KASAN enabled, clang fails to optimize the inline version of
vdec_vp9_slice_map_counts_eob_coef() properly, leading to kilobytes
of temporary values spilled to the stack:
drivers/media/platform/mediatek/vcodec/decoder/vdec/vdec_vp9_req_lat_if.c:1526:12: error: stack frame size (2160) exceeds limit (2048) in 'vdec_vp9_slice_update_prob' [-Werror,-Wframe-larger-than]
This seems to affect all versions of clang including the latest (clang-20),
but the degree of stack overhead is different per release.
Marking the function as noinline_for_stack is harmless here and avoids
the problem completely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the cmdq_pkt_create() and cmdq_pkt_destroy() common functions
instead of implementing specific mdp3 versions.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to have fine-grained control, use cmdq_pkt_eoc() and
cmdq_pkt_jump_rel() to replace cmdq_pkt_finalize().
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Just like was done with MM_REG_WRITE, remove the mask from the
MM_REG_POLL macro, leaving MM_REG_POLL_MASK to be used when a mask is
required, and update the call sites accordingly. In this case, all calls
require a mask, so MM_REG_POLL remains unused, but at least this makes
the MM_REG_POLL macros consistent with the MM_REG_WRITE ones.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are two macros to issue a cmdq write: MM_REG_WRITE_MASK and
MM_REG_WRITE, but confusingly, both of them take a mask parameter. The
difference is that MM_REG_WRITE additionally checks whether the mask
passed in contains the register mask, in which case, the 0xffffffff mask
is passed to cmdq_pkt_write_mask(), effectively disregarding the mask
and calling cmdq_pkt_write() as an optimization.
Move that optimization to the MM_REG_WRITE_MASK macro and make
MM_REG_WRITE the variant that doesn't take a mask, directly calling to
cmdq_pkt_write().
Change the call sites to MM_REG_WRITE whenever a mask wasn't necessary
(ie 0xffffffff or a <register>_MASK was passed as mask) and in other
cases to MM_REG_WRITE_MASK.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
