Right now, when a gpio value is set, the actual hardware pin gets set
asynchronously. When linux write the output register, it takes some time
until it is actually propagated to the output shift registers. If that
output port is connected to an I2C mux for example, the linux driver
assumes the I2C bus is already switched although it is not.
Fortunately, there is a single shot mode with a feedback: you can
trigger the single shot and the hardware will clear that bit once it has
finished the clocking and strobed the load signal of the shift
registers. This can take a considerable amount of time though.
Measuremens have shown that it takes up to a whole burst cycle gap which
is about 50ms on the largest setting. Therefore, we have to mark the
output bank as sleepable. To avoid unnecessary waiting, just trigger the
single shot if the value was actually changed.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-6-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sgpio_output_set() return an error value. Don't just ignore the
return value of any regmap access but propagate it to our callers. Even
if the accesses never fail, this is a preparation patch to add single
shot mode where we need to poll a bit and thus we might get -ETIMEDOUT.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-5-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert sgpio_clrsetbits() to use regmap_update_bits() and drop the
spinlocks because regmap already takes care of the locking.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-4-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt ack register has the usual "write one to clear" semantics.
No read-modify-write is required here.
This is also a preparation patch to change the sgpio_clrsetbits() to use
regmap_update_bits() which don't write the value if it is not changed.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-3-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Protect any RMW access to the registers by a spinlock.
Fixes: 7e5ea974e61c ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220226204507.2511633-2-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On lan966x platform when the switch gets reseted then also the sgpio
gets reseted. The fix for this is to extend also the sgpio driver to
call the reset driver which will be reseted only once by the first
driver that is probed.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20211018085754.1066056-3-horatiu.vultur@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
device_for_each_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 7e5ea974e61c ("pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO")
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210606191940.29312-1-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes using a wrong register offset when configuring an IRQ
trigger type.
Fixes: be2dc859abd4 ("pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)")
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210203123825.611576-1-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds 'interrupt-controller' features for the signals available on
the Microchip SGPIO controller, however only for controller versions
on the Sparx5 platform (or later).
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201209142753.683208-2-lars.povlsen@microchip.com
[Select GPIOLIB_IRQCHIP in Kconfig]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following sparse warnings:
drivers/pinctrl/pinctrl-microchip-sgpio.c:63:31: warning: symbol 'properties_luton' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:68:31: warning: symbol 'properties_ocelot' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:73:31: warning: symbol 'properties_sparx5' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1606218173-3722-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
(SGPIO) device used in various SoC's.
The driver is added as a pinctrl driver, albeit only having just GPIO
support currently. The hardware supports other functions that will be
added following.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201113145151.68900-3-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
