When DMA is used in RS485 mode make sure that the UARTs tx section is
enabled before the DMA buffers are queued for transmission.
Cc: stable@vger.kernel.org
Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240216224709.9928-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 07c30ea5861f ("serial: Do not hold the port lock when setting
rx-during-tx GPIO") the SER_RS485_RX_DURING_TX flag was only set if the
rx-during-tx mode was not controlled by a GPIO. Now the flag is set
unconditionally when RS485 is enabled. This results in an incorrect setting
if the rx-during-tx GPIO is not asserted.
Fix this by setting the flag only if the rx-during-tx mode is not
controlled by a GPIO and thus restore the correct behaviour.
Cc: stable@vger.kernel.org # 6.6+
Fixes: 07c30ea5861f ("serial: Do not hold the port lock when setting rx-during-tx GPIO")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240216224709.9928-1-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new SBI console has the same problem as the old one: there's only
one shared backing hardware and no synchronization, so the two drivers
end up stepping on each other. This was the same issue the old SBI-0.1
console drivers had, but that was disabled by default when SBI-0.1 was.
So just mark the new driver as nonportable.
Reported-by: Emil Renner Berthing <kernel@esmil.dk>
Fixes: 88ead68e764c ("tty: Add SBI debug console support to HVC SBI driver")
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240214153429.16484-2-palmer@rivosinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emil reports:
After updating Linux on an i.MX28 board, serial communication over
AUART broke. When I TX from the board and measure on the TX pin, it
seems like the HW fifo is not emptied before the transmission is
stopped.
MXS performs weird things with stop_tx(). The driver makes it
conditional on uart_tx_stopped().
So the driver needs special handling. Pass the brand new UART_TX_NOSTOP
to uart_port_tx_flags() and handle the stop on its own.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Emil Kronborg <emil.kronborg@protonmail.com>
Cc: stable <stable@kernel.org>
Fixes: 2d141e683e9a ("tty: serial: use uart_port_tx() helper")
Closes: https://lore.kernel.org/all/miwgbnvy3hjpnricubg76ytpn7xoceehwahupy25bubbduu23s@om2lptpa26xw/
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240201105557.28043-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was reviewing this code again and I realized I made a mistake here.
It should have been > instead of >=. The subtract ensures that we
don't go out of bounds. My patch meant that we don't read the last
chunk of the buffer.
Fixes: 86ee55e9bc7f ("serial: 8250_pci1xxxx: fix off by one in pci1xxxx_process_read_data()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/bd6fb361-bbb9-427d-90e8-a5df4de76221@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a problem after resetting a port, the do/while() loop that
checks the default value of DIVLSB register may run forever and spam the
I2C bus.
Add a delay before each read of DIVLSB, and a maximum number of tries to
prevent that situation from happening.
Also fail probe if port reset is unsuccessful.
Fixes: 10d8b34a4217 ("serial: max310x: Driver rework")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
Fixes: 4cf9a888fd3c ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Suggested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://www.spinics.net/lists/linux-serial/msg35773.html
Link: https://lore.kernel.org/all/20240110174015.6f20195fde08e5c9e64e5675@hugovil.com/raw
Link: e5dfe3e4a7
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If regmap_read() returns a non-zero value, the 'val' variable can be left
uninitialized.
Clear it before calling regmap_read() to make sure we properly detect
the clock ready bit.
Fixes: 4cf9a888fd3c ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In uart_tiocmget():
result = uport->mctrl;
uart_port_lock_irq(uport);
result |= uport->ops->get_mctrl(uport);
uart_port_unlock_irq(uport);
...
return result;
In uart_update_mctrl():
uart_port_lock_irqsave(port, &flags);
...
port->mctrl = (old & ~clear) | set;
...
port->ops->set_mctrl(port, port->mctrl);
...
uart_port_unlock_irqrestore(port, flags);
An atomicity violation is identified due to the concurrent execution of
uart_tiocmget() and uart_update_mctrl(). After assigning
result = uport->mctrl, the mctrl value may change in uart_update_mctrl(),
leading to a mismatch between the value returned by
uport->ops->get_mctrl(uport) and the mctrl value previously read.
This can result in uart_tiocmget() returning an incorrect value.
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 5.17.
To address this issue, it is suggested to move the line
result = uport->mctrl inside the uart_port_lock block to ensure atomicity
and prevent the mctrl value from being altered during the execution of
uart_tiocmget(). With this patch applied, our tool no longer reports the
bug, with the kernel configuration allyesconfig for x86_64. Due to the
absence of the requisite hardware, we are unable to conduct runtime
testing of the patch. Therefore, our verification is solely based on code
logic analysis.
[1] https://sites.google.com/view/basscheck/
Fixes: c5f4644e6c8b ("[PATCH] Serial: Adjust serial locking")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/r/20240112113624.17048-1-2045gemini@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These > comparisons should be >= to prevent writing one element beyond
the end of the rx_buff[] array. The rx_buff[] buffer has RX_BUF_SIZE
elements. Fix the buffer overflow.
Fixes: aba8290f368d ("8250: microchip: pci1xxxx: Add Burst mode reception support in uart driver for writing into FIFO")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ZZ7vIfj7Jgh-pJn8@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This includes everything from part 2:
* Support for tuning for systems with fast misaligned accesses.
* Support for SBI-based suspend.
* Support for the new SBI debug console extension.
* The T-Head CMOs now use PA-based flushes.
* Support for enabling the V extension in kernel code.
* Optimized IP checksum routines.
* Various ftrace improvements.
* Support for archrandom, which depends on the Zkr extension.
and then also a fix for those:
* The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
-----BEGIN PGP SIGNATURE-----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=Sjhj
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for tuning for systems with fast misaligned accesses.
- Support for SBI-based suspend.
- Support for the new SBI debug console extension.
- The T-Head CMOs now use PA-based flushes.
- Support for enabling the V extension in kernel code.
- Optimized IP checksum routines.
- Various ftrace improvements.
- Support for archrandom, which depends on the Zkr extension.
- The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
lib: checksum: Fix build with CONFIG_NET=n
riscv: lib: Check if output in asm goto supported
riscv: Fix build error on rv32 + XIP
riscv: optimize ELF relocation function in riscv
RISC-V: Implement archrandom when Zkr is available
riscv: Optimize hweight API with Zbb extension
riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
riscv: ftrace: Make function graph use ftrace directly
riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
riscv: Restrict DWARF5 when building with LLVM to known working versions
riscv: Hoist linker relaxation disabling logic into Kconfig
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
RISC-V: selftests: cbo: Ensure asm operands match constraints
...
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty core
and drivers in here, along with the usual set of rs485 updates (someday
this might work properly...) Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeUaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyOgCgp1uhP/b9iW6qM7qL6OYEG6idI0kAnj0VASNm
vSI69HmdKKwo69YLOSBp
=14n1
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
- New Device Support
- Add support for AW20108 to Awinic LED driver
- New Functionality
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off via sysfs if required
- Add support for hardware control in AW200xx
- Fix-ups
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify, avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
- Bug Fixes
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct operation
- Avoid division-by-zero issues
-----BEGIN PGP SIGNATURE-----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=/f98
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
New Device Support:
- Add support for AW20108 to Awinic LED driver
New Functionality:
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off
via sysfs if required
- Add support for hardware control in AW200xx
Fix-ups:
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify,
avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
Bug Fixes:
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct
operation
- Avoid division-by-zero issues"
* tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (45 commits)
leds: trigger: netdev: Add core support for hw not supporting fallback to LED sw control
leds: trigger: panic: Don't register panic notifier if creating the trigger failed
leds: sun50i-a100: Convert to be agnostic to property provider
leds: max5970: Add missing headers
leds: max5970: Make use of dev_err_probe()
leds: max5970: Make use of device properties
leds: max5970: Remove unused variable
leds: rgb: Drop obsolete dependency on COMPILE_TEST
leds: sun50i-a100: Avoid division-by-zero warning
leds: trigger: Remove unused function led_trigger_rename_static()
leds: qcom-lpg: Introduce a wrapper for getting driver data from a pwm chip
leds: gpio: Add kernel log if devm_fwnode_gpiod_get() fails
dt-bindings: leds: qcom,spmi-flash-led: Fix example node name
dt-bindings: leds: aw200xx: Fix led pattern and add reg constraints
dt-bindings: leds: awinic,aw200xx: Add AW20108 device
leds: aw200xx: Add support for aw20108 device
leds: aw200xx: Improve autodim calculation method
leds: aw200xx: Enable disable_locking flag in regmap config
leds: aw200xx: Add delay after software reset
dt-bindings: leds: aw200xx: Remove property "awinic,display-rows"
...
A new drivers/cache/ subsystem is added to contain drivers for abstracting
cache flush methods on riscv and potentially others, as this is needed for
handling non-coherent DMA but several SoCs require nonstandard hardware
methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and MT8195,
and driver support for MT8188 along with some code refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and hisilicon
-----BEGIN PGP SIGNATURE-----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=4bKY
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"A new drivers/cache/ subsystem is added to contain drivers for
abstracting cache flush methods on riscv and potentially others, as
this is needed for handling non-coherent DMA but several SoCs require
nonstandard hardware methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and
MT8195, and driver support for MT8188 along with some code
refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA
bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and
hisilicon"
* tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (189 commits)
memory: ti-emif-pm: Convert to platform remove callback returning void
memory: ti-aemif: Convert to platform remove callback returning void
memory: tegra210-emc: Convert to platform remove callback returning void
memory: tegra186-emc: Convert to platform remove callback returning void
memory: stm32-fmc2-ebi: Convert to platform remove callback returning void
memory: exynos5422-dmc: Convert to platform remove callback returning void
memory: renesas-rpc-if: Convert to platform remove callback returning void
memory: omap-gpmc: Convert to platform remove callback returning void
memory: mtk-smi: Convert to platform remove callback returning void
memory: jz4780-nemc: Convert to platform remove callback returning void
memory: fsl_ifc: Convert to platform remove callback returning void
memory: fsl-corenet-cf: Convert to platform remove callback returning void
memory: emif: Convert to platform remove callback returning void
memory: brcmstb_memc: Convert to platform remove callback returning void
memory: brcmstb_dpfe: Convert to platform remove callback returning void
soc: qcom: llcc: Fix LLCC_TRP_ATTR2_CFGn offset
firmware: qcom: qseecom: fix memory leaks in error paths
dt-bindings: clock: google,gs101: rename CMU_TOP gate defines
soc: qcom: llcc: Fix typo in kernel-doc
dt-bindings: soc: qcom,aoss-qmp: document the X1E80100 Always-On Subsystem side channel
...
We extend the existing RISC-V SBI earlycon support to use the new
RISC-V SBI debug console extension.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231124070905.1043092-4-apatel@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Move common code for EFR lock/unlock of mutex into functions for code reuse
and clarity.
With the addition of old_lcr, move irda_mode within struct sc16is7xx_one to
reduce memory usage:
Before: /* size: 752, cachelines: 12, members: 10 */
After: /* size: 744, cachelines: 12, members: 10 */
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-17-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move/reorder some functions to remove sc16is7xx_ier_set() and
sc16is7xx_stop_tx() prototypes declarations.
No functional change.
sc16is7xx_ier_set() was introduced in
commit cc4c1d05eb10 ("sc16is7xx: Properly resume TX after stop").
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-16-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify FIFO access functions by avoiding to declare
a struct sc16is7xx_port *s variable within each function.
This is mainly done to have more commonality between the max310x and
sc16is7xx drivers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MODULE_DEVICE_TABLE() already creates the proper aliases for the
SPI driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To better show why the limit is what it is, since we have only 16 bits for
the divisor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows to simplify code by removing the break statement in the default
switch/case in some functions.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the driver name is displayed instead of "unknown" when
displaying the driver infos:
Before:
grep ttySC /proc/tty/drivers
unknown /dev/ttySC 243 0-7 serial
After:
grep ttySC /proc/tty/drivers
sc16is7xx /dev/ttySC 243 0-7 serial
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred i2c_get_match_data() instead of device_get_match_data()
and i2c_client_get_device_id() to get the driver match data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred spi_get_device_match_data() instead of
device_get_match_data() and spi_get_device_id() to get the driver match
data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-8-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the explicit sc16is7xx_lines bitfield declaration with the generic
macro DECLARE_BITMAP() to reserve just enough memory to contain all
required bits.
This also improves code self-documentation by showing the maximum number
of bits required.
This conversion now makes sc16is7xx_lines an array, so drop the "&" before
sc16is7xx_lines in all bit access functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify and improve readability by replacing while(1) loop with
do {} while, and by using the keep_polling variable as the exit
condition, making it more explicit.
Fixes: 834449872105 ("sc16is7xx: Fix for multi-channel stall")
Cc: <stable@vger.kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 834449872105 ("sc16is7xx: Fix for multi-channel stall") changed
sc16is7xx_port_irq() from looping multiple times when there was still
interrupts to serve. It simply changed the do {} while(1) loop to a
do {} while(0) loop, which makes the loop itself now obsolete.
Clean the code by removing this obsolete do {} while(0) loop.
Fixes: 834449872105 ("sc16is7xx: Fix for multi-channel stall")
Cc: <stable@vger.kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error occurs during probing, the sc16is7xx_lines bitfield may be left
in a state that doesn't represent the correct state of lines allocation.
For example, in a system with two SC16 devices, if an error occurs only
during probing of channel (port) B of the second device, sc16is7xx_lines
final state will be 00001011b instead of the expected 00000011b.
This is caused in part because of the "i--" in the for/loop located in
the out_ports: error path.
Fix this by checking the return value of uart_add_one_port() and set line
allocation bit only if this was successful. This allows the refactor of
the obfuscated for(i--...) loop in the error path, and properly call
uart_remove_one_port() only when needed, and properly unset line allocation
bits.
Also use same mechanism in remove() when calling uart_remove_one_port().
Fixes: c64349722d14 ("sc16is7xx: support multiple devices")
Cc: <stable@vger.kernel.org>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers RS485 support is deactivated if there is no RTS GPIO available.
This is done by nullifying the ports rs485_supported struct. After that
however the settings in serial_omap_rs485_supported are assigned to the
same structure unconditionally, which results in an unintended reactivation
of RS485 support.
Fix this by moving the assignment to the beginning of
serial_omap_probe_rs485() and thus before uart_get_rs485_mode() gets
called.
Also replace the assignment of rs485_config() to have the complete RS485
setup in one function.
Fixes: e2752ae3cfc9 ("serial: omap: Disallow RS-485 if rts-gpio is not specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-7-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.
This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.
Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.
With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.
Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.
Fixes: 00d7a00e2a6f ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-6-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some uart drivers specify a rs485_config() function and then decide later
to disable RS485 support for some reason (e.g. imx and ar933).
In these cases userspace may be able to activate RS485 via TIOCSRS485
nevertheless, since in uart_set_rs485_config() an existing rs485_config()
function indicates that RS485 is supported.
Make sure that this is not longer possible by checking the uarts
rs485_supported.flags instead and bailing out if SER_RS485_ENABLED is not
set.
Furthermore instead of returning an empty structure return -ENOTTY if the
RS485 configuration is requested via TIOCGRS485 but RS485 is not supported.
This has a small impact on userspace visibility but it is consistent with
the -ENOTTY error for TIOCGRS485.
Fixes: e849145e1fdd ("serial: ar933x: Fill in rs485_supported")
Fixes: 55e18c6b6d42 ("serial: imx: Remove serial_rs485 sanitization")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-5-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Among other things uart_sanitize_serial_rs485() tests the sanity of the RTS
settings in a RS485 configuration that has been passed by userspace.
If RTS-on-send and RTS-after-send are both set or unset the configuration
is adjusted and RTS-after-send is disabled and RTS-on-send enabled.
This however makes only sense if both RTS modes are actually supported by
the driver.
With commit be2e2cb1d281 ("serial: Sanitize rs485_struct") the code does
take the driver support into account but only checks if one of both RTS
modes are supported. This may lead to the errorneous result of RTS-on-send
being set even if only RTS-after-send is supported.
Fix this by changing the implemented logic: First clear all unsupported
flags in the RS485 configuration, then adjust an invalid RTS setting by
taking into account which RTS mode is supported.
Cc: <stable@vger.kernel.org>
Fixes: be2e2cb1d281 ("serial: Sanitize rs485_struct")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-4-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the RS485 feature RX-during-TX is supported by means of a GPIO set the
according supported flag. Otherwise setting this feature from userspace may
not be possible, since in uart_sanitize_serial_rs485() the passed RS485
configuration is matched against the supported features and unsupported
settings are thereby removed and thus take no effect.
Cc: <stable@vger.kernel.org>
Fixes: 163f080eb717 ("serial: core: Add option to output RS485 RX_DURING_TX state via GPIO")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-3-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
Since this function is called with the port lock held, this can be a
problem in case that setting the GPIO line can sleep (e.g. if a GPIO
expander is used which is connected via SPI or I2C).
Avoid this issue by moving the GPIO setting outside of the port lock into
the serial core and thus making it a generic feature.
Also with commit c54d48543689 ("serial: stm32: Add support for rs485
RX_DURING_TX output GPIO") the SER_RS485_RX_DURING_TX flag is only set if a
rx-during-tx GPIO is _not_ available, which is wrong. Fix this, too.
Furthermore reset old GPIO settings in case that changing the RS485
configuration failed.
Fixes: c54d48543689 ("serial: stm32: Add support for rs485 RX_DURING_TX output GPIO")
Fixes: ca530cfa968c ("serial: imx: Add support for RS485 RX_DURING_TX output GPIO")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In PCI1XXXX C0 endpoint, support for Burst mode is added.
pci1xxxx_handle_irq checks the burst status and based on that
incoming characters are received in DWORDs, RX handling is done
in pci1xxxx_rx_burst. While reading the burst status the RX error
is checked and the corresponding error statistics are updated.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20231215151123.41812-4-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Different Host drivers can attempt to access system registers
simultaneously from different memory spaces at the same time. The
syslock mechanism provides a safe option for reading UART system
registers and prevents conflicts by serializing access. Added
three padding bytes in the structure for memory alignment.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20231215151123.41812-3-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Structure declarations in 8250_pci1xxxx.c have been moved above
the functions for code readability.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20231215151123.41812-2-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_kmemdup() helper to copy dma_param instead of doing it manually.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20240102055006.27256-1-raag.jadav@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After switching the serial interface of the Moxa RS232 PCIe boards, it
fails to reset to RS232 when attempting to reload 8250_pci driver.
This patch set RS232 as the default setting during the initialization of
Moxa PCIe board.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Link: https://lore.kernel.org/r/20240102053133.9795-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Designware UART has optional feature FIFO_MODE to implement FIFO.
Encoding FIFO capabilities through Component Parameter Register CPR is
optional and it can be enabled using parameter UART_ADD_ENCODED_PARAMS.
Driver can exercise fifo capabilities by decoding CPR if implemented
or from cpr_val provided from the dw8250_platform_data otherwise.
dw8250_setup_port() checks for CPR or cpr_val to determine FIFO size
only when Component Version (UCV) is non-zero. Bailing out early on UCV
read returning zero will leave fifosize as zero and !UART_CAP_FIFO,
hence prevent early return and continue to process CPR or cpr_val for
the driver to utilize FIFO.
Non-zero UCV implies ADDITIONAL_FEATURES=1, preventing early return
will not be an overhead here.
Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231231182951.877805-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986e6 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.
Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a leon kernel with qemu there where no console prompt.
The root cause is the handling of the fifo size in the tx part of the
apbuart driver.
The qemu uart driver only have a very rudimentary status handling and do
not report the number of chars queued in the tx fifo in the status register.
So the driver ends up with a fifo size of 1.
In the tx path the fifo size is divided by 2 - resulting in a fifo
size of zero.
The original implementation would always try to send one char, but
after the introduction of uart_port_tx_limited() the fifo size is
respected even for the first char.
There seems to be no good reason to divide the fifo size with two - so
remove this. It looks like something copied from the original amba driver.
With qemu we now have a minimum fifo size of one char, so we show
the prompt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: d11cc8c3c4b6 ("tty: serial: use uart_port_tx_limited()")
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: <linux-serial@vger.kernel.org>
Cc: <sparclinux@vger.kernel.org>
Link: https://lore.kernel.org/r/20231226121607.GA2622970@ravnborg.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
