Commit Graph

148 Commits

Author SHA1 Message Date
Wolfram Sang
d61366cd7a mmc: sh_mmcif: correctly report success when obtaining DMA channels
The debug message could still report success when getting the channels
was OK but configuring them failed. This actually caused a minor detour
when debugging DMA problems, so make sure the success is only reported
when the channels are really ready-to-use.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240928094454.3592-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-10-14 12:40:10 +02:00
Uwe Kleine-König
078e548af9 mmc: Switch back to struct platform_driver::remove()
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.

Convert all platform drivers below drivers/mmc to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240927145832.754697-2-u.kleine-koenig@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-10-14 12:29:01 +02:00
Linus Walleij
4d4a2c71b8 mmc: sh_mmcif: Advance sg_miter before reading blocks
The introduction of sg_miter was a bit sloppy as it didn't
exactly mimic the semantics of the old code on multiblock reads
and writes: these like you to:

- Advance to the first sglist entry *before* starting to read
  any blocks from the card.

- Advance and check availability of the next entry *right after*
  processing one block.

Not checking if we have more sglist entries right after
reading a block will lead to this not being checked until we
return to the callback to read out more blocks, i.e. until the
next interrupt arrives. Since the last block is the last one
(no more data will arrive) there will not be a next interrupt,
and we will be waiting forever resulting in a timeout for
command 18 when reading multiple blocks.

The same bug was fixed also in the writing of multiple blocks.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 27b57277d9 ("mmc: sh_mmcif: Use sg_miter for PIO")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240221-fix-sh-mmcif-v2-2-5e521eb25ae4@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-02-28 13:31:31 +01:00
Linus Walleij
727cba706d mmc: sh_mmcif: sg_miter must not be atomic
All the sglist iterations happen in the *threaded* interrupt handler and
that context is not atomic, so don't request an atomic sglist miter. Using
an atomic miter results in "BUG: scheduling while atomic" splats.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 27b57277d9 ("mmc: sh_mmcif: Use sg_miter for PIO")
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240221-fix-sh-mmcif-v2-1-5e521eb25ae4@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-02-28 13:30:16 +01:00
Linus Walleij
27b57277d9 mmc: sh_mmcif: Use sg_miter for PIO
Use sg_miter iterator instead of sg_virt() and custom code
to loop over the scatterlist. The memory iterator will do
bounce buffering if the page happens to be located in high memory,
which the driver may or may not be using.

Suggested-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/linux-mmc/20240122073423.GA25859@lst.de/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240127-mmc-proper-kmap-v2-9-d8e732aa97d1@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2024-02-13 13:40:56 +01:00
Yangtao Li
8fc8c82dfa mmc: sh_mmcif: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.

Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230727070051.17778-18-frank.li@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2023-08-15 12:45:04 +02:00
Rob Herring
c62da8a8a9 mmc: Explicitly include correct DT includes
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.

Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230718143054.1065288-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2023-08-09 13:21:48 +02:00
Sergey Shtylyov
5b067d7f85 mmc: sh_mmcif: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.

Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230617203622.6812-11-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2023-06-19 13:31:12 +02:00
Wolfram Sang
13acb62ce1 mmc: sh_mmcif: move platform_data header to proper location
We have a dedicated directory for platform_data meanwhile, don't spoil
the MMC directory with it.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220412093102.3428-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2022-04-26 14:05:21 +02:00
Geert Uytterhoeven
bee1549199 mmc: sh_mmcif: Simplify division/shift logic
"a / (1 << b)" == "a >> b".

No change in generated code.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/68d689c39c769d298b53ee8cb9de0e594a2999b2.1645460780.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2022-02-28 16:11:47 +01:00
Jiasheng Jiang
4d315357b3 mmc: sh_mmcif: Check for null res pointer
If there is no suitable resource, platform_get_resource() will return
NULL.
Therefore in order to avoid the dereference of the NULL pointer, it
should be better to check the 'res'.

Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: stable@vger.kernel.org # v5.16+
Link: https://lore.kernel.org/r/20220119120006.1426964-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2022-01-24 15:37:13 +01:00
Wolfram Sang
492200f247 mmc: sh_mmcif: use proper DMAENGINE API for termination
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210623095734.3046-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2021-08-24 10:15:30 +02:00
Douglas Anderson
21b2cec61c mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers.  This batch converts
the drivers that appeared to be around in the v4.4 timeframe.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SH_MMCIF
Tested-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200903162412.1.Id501e96fa63224f77bb86b2135a5e8324ffb9c43@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-09-07 14:20:17 +02:00
Geert Uytterhoeven
b9a349fdc7 mmc: sh_mmcif: Use "kHz" for kilohertz
"K" stands for "kelvin".

While at it, make the spacing before units consistent.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200618080321.16678-1-geert+renesas@glider.be
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-07-13 12:18:23 +02:00
Peter Ujfalusi
b67b45179b mmc: sh_mmcif: Use dma_request_chan() instead dma_request_slave_channel()
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA if needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113031.31847-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-12-19 08:19:42 +01:00
Yangtao Li
34ac4509f2 mmc: sh_mmcif: convert to devm_platform_ioremap_resource
Use devm_platform_ioremap_resource() to simplify code.

Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191215175120.3290-6-tiny.windzz@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-12-18 14:46:06 +01:00
Geert Uytterhoeven
faf97b84fa mmc: sh_mmcif: Use platform_get_irq_optional() for optional interrupt
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:

    sh_mmcif ee200000.mmc: IRQ index 1 not found

Fix this by calling platform_get_irq_optional() instead for the second
interrupt, which is optional.

Remove the now superfluous error printing for the first interrupt, which
is mandatory.

Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-10-03 11:38:37 +02:00
Wolfram Sang
f707079df8 mmc: use SPDX identifier for Renesas drivers
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Wolfram Sang
5a871bf081 mmc: sh_mmcif: remove some cruft
The TODO section from 2010 is obsolete. We have DMA and PM meanwhile and
we always want to handle errors better, if possible. Also DRIVER_VERSION
is not used anymore these days.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-03-05 09:00:59 +01:00
Colin Ian King
659032dcb9 mmc: sh_mmcif: remove redundant initialization of 'opc'
Variable opc is initialized with a value that is never read, opc
is later re-assigned a newer value, hence the initialization can
be removed.

Cleans up clang warning:
drivers/mmc/host/sh_mmcif.c:919:6: warning: Value stored to 'opc'
during its initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-18 09:08:11 +01:00
Julia Lawall
1586cbb354 mmc: sh_mmcif: constify mmc_host_ops structures
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const.  Thus the mmc_host_ops
structure itself can be const.

Done with the help of Coccinelle.

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };

@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p

@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct mmc_host_ops i = { ... };
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:01:42 +02:00
Ulf Hansson
dba4bb484e mmc: sh_mmcif: Remove unused clk_ctrl2_present from the platform data
There are currently no users of the clk_ctrl2_present member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may support clk_ctrl2, let's keep
the current code in the driver, which deals with this. For future support,
we should invent a DT binding instead, but let's leave that until it's
needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:19:58 +01:00
Ulf Hansson
8020f71117 mmc: sh_mmcif: Remove unused ccs_unsupported from the platform data
There are currently no users of the ccs_unsupported member from the
platform data, so let's remove it.

Note, as some of the sh_mmcif variants may not support ccs, let's keep the
current code in the driver, which deals with this. For future support, we
should invent a DT binding instead, but let's leave that until it's needed.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:19:58 +01:00
Ulf Hansson
5957eeba53 mmc: sh_mmcif: Remove unused ->get_cd() platform callback
Removing the callback also enables us to remove the sh_mmcif_get_cd()
altogether, as we convert to use mmc_gpio_get_cd() to the same kind of
work.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-02-13 13:19:57 +01:00
Ulf Hansson
95cc4df716 mmc: sh_mmcif: Remove unused use_cd_gpio/cd_gpio from platform data
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:19:57 +01:00
Ulf Hansson
52e00b8418 mmc: sh_mmcif: Use a 10s timeout in the error recovery path
The current value means an mdelay(1) may execute up to 10000000 times,
which translates to around ~2.8 hours. This is probably not what the
orignal author had in mind. Let's instead use 10s, which is the same value
sh_mmcif is using for other timeouts.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:25 +02:00
Ulf Hansson
549646a9c7 mmc: sh_mmcif: Inform the mmc core about the max busy timeout
The sh_mmcif driver is already using a 10s request timeout. Let's also
inform the mmc core about this value, as there are situations when it
needs to know about it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:24 +02:00
Ulf Hansson
5b1c29bcee mmc: sh_mmcif: Use response type to know when to enable busy detection
The sh_mmcif explicity checks for certain commands to decide when to
enable HW busy detection. Instead, it should only check the response type
as it tells if busy detection is needed.

In this way, the mmc core also gets full control whether it thinks busy
detection should be done or not. In some specific scenarios, like for
ERASE and STOP commands it may decide to fall back to use a CMD13 to poll
the card status instead.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:23 +02:00
Ulf Hansson
dab3a28b40 mmc: sh_mmcif: Enable MMC_CAP2_NO_SD and MMC_CAP2_NO_SDIO
Enable the capabilities which tells the mmc core to prevent sending SD and
SDIO commands during card initialization. In this way, we can also remove
the validation of non-supported commands in the ->request() callback.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:23 +02:00
Ulf Hansson
33a31ceaf0 mmc: sh_mmci: Get rid of wrapper function for regulators
As there are two callers of sh_mmcif_set_power() and because its only
additional action is to check for a valid regulator, let's just remove it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-02 10:33:09 +02:00
Ulf Hansson
4caf653a55 mmc: sh_mmcif: Restructure ->set_ios()
Both from a runtime PM and clock management point of view, the ->set_ios()
code is unnecessary complex.

A suboptimal path is also executed when the mmc core requests a clock rate
of zero. As that happens during the card initialization phase, trying to
save power by decreasing the runtime PM usage count and gating the clock
via clk_disable_unprepare() is just superfluous.

Moreover, from a runtime PM point of view the core will anyway keep the
device active during the entire card initialization phase.

Restructure the code to rely on the ios->power_mode to understand when the
runtime PM usage count needs to be increased. Let's also deal with clock
rate changes by simply applying the rate.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-02 10:33:08 +02:00
Ulf Hansson
88ac2a2c30 mmc: sh_mmcif: Make sure the device stays active when needed in ->probe()
While accessing the device, make sure it stays active by increasing the
runtime PM usage count for it.

Let's also defer to enable runtime PM until we really need access to the
device. This also enables the error path in ->probe() to become simpler.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-02 10:33:08 +02:00
Kirill A. Shutemov
09cbfeaf1a mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.

This promise never materialized.  And unlikely will.

We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE.  And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.

Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.

Let's stop pretending that pages in page cache are special.  They are
not.

The changes are pretty straight-forward:

 - <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;

 - <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;

 - PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};

 - page_cache_get() -> get_page();

 - page_cache_release() -> put_page();

This patch contains automated changes generated with coccinelle using
script below.  For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.

The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.

There are few places in the code where coccinelle didn't reach.  I'll
fix them manually in a separate patch.  Comments and documentation also
will be addressed with the separate patch.

virtual patch

@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E

@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E

@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT

@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE

@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK

@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)

@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)

@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)

Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-04-04 10:41:08 -07:00
Geliang Tang
1046a81151 mmc: sh_mmcif: use to_delayed_work
Use to_delayed_work() instead of open-coding it.

Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-02-29 11:02:46 +01:00
Chris Paterson
a32ef81c98 mmc: sh_mmcif: Correct TX DMA channel allocation
Commit 27cbd7e815 ("mmc: sh_mmcif: rework dma channel handling")
introduced a typo causing the TX DMA channel allocation to be overwritten
by the requested RX DMA channel.

Fixes: 27cbd7e815 ("mmc: sh_mmcif: rework dma channel handling")
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-02-10 17:02:25 +01:00
Arnd Bergmann
27cbd7e815 mmc: sh_mmcif: rework dma channel handling
When compiling the sh_mmcif driver for ARM64, we currently
get a harmless build warning:

../drivers/mmc/host/sh_mmcif.c: In function 'sh_mmcif_request_dma_one':
../drivers/mmc/host/sh_mmcif.c:417:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
    (void *)pdata->slave_id_tx :
    ^
../drivers/mmc/host/sh_mmcif.c:418:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
    (void *)pdata->slave_id_rx;

This could be worked around by adding another cast to uintptr_t, but
I decided to simplify the code a little more to avoid that. This
splits out the platform data using code into a separate function
and builds that only for CONFIG_SUPERH. This part still has a typecast
but does not need a second one. The SH platform code could be further
modified to pass a pointer directly as we do on other architectures
when we have a filter function.

The normal case is simplified further and now just calls
dma_request_slave_channel() directly without going through the
compat handling.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-12-22 11:32:08 +01:00
Koji Matsuoka
5afc30fc66 mmc: sh_mmcif: Fix suspend process
The clock should be enable when SDHI registers are accessed.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-08-27 14:50:57 +02:00
Kuninori Morimoto
89d49a706c mmc: sh_mmcif: calculate best clock with parent clock
MMCIF IP on R-Car series has parent clock which can be set several rate,
and it was not implemented on old SH-Mobile series (= SH-Mobile series
parent clock was fixed rate) R-Car series MMCIF can use more high speed
access if it setups parent clock. This patch adds parent clock setup
method. It will be used if DT has "max-frequency", and then, this driver
assumes it is booted on R-Car Gen2 or later SoC. Because SH-Mobile series
(which doesn't boot from DT) and R-Car series (which boots from DT) have
different divider.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Silence compiler warning]
2015-06-01 09:07:10 +02:00
Kuninori Morimoto
1b1a694d53 mmc: sh_mmcif: use sh_mmcif_xxx prefix for all functions
Current sh_mmcif driver is using sh_mmcif_xxx and mmcif_xxx
for functions. This patch used sh_mmcif_xxx for all functions.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:09 +02:00
Kuninori Morimoto
585c3a5a0b mmc: sh_mmcif: add sh_mmcif_host_to_dev() macro and use it.
Current sh_mmcif driver is directly using &host->pd->dev in all place.
It is not big problem, but it is unreadable, and it can be cause of
future bug. This patch adds new sh_mmcif_host_to_dev() and use it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:09 +02:00
Kuninori Morimoto
9bb09a30ee mmc: sh_mmcif: separate sh_mmcif_clk_update() into setup and prepare
Current sh_mmcif_clk_update() is called from probe() and set_ios(),
but, the purpose of later one is just clk_prepare_enable().
No need to setup mmc->f_max/f_min in many times.
This patch separe sh_mmcif_clk_update() into clk_prepare_enable()
and mmc->f_max/f_min setup.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-05-25 09:20:06 +02:00
Kuninori Morimoto
6aed678bcd mmc: sh_mmcif: remove unnecessary int clk from struct sh_mmcif_host
struct sh_mmcif_host has 1) int clk, 2) struct clock *hclk,
and host->clk = clk_get_rate(host->hclk).
This int clk is not necessary. Let's remove it.
And, current hclk is confusable naming. Let's rename it to clk.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-05-25 09:20:05 +02:00
Kuninori Morimoto
60985c39cf mmc: sh_mmcif: cleanup to use dev instead of &pdev->dev
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-05-25 09:20:05 +02:00
Kuninori Morimoto
70830b4182 mmc: sh_mmcif: move mmcif_of_match to upside
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-05-25 09:20:04 +02:00
Takeshi Kihara
bad4371d87 mmc: sh_mmcif: Fix timeout value for command request
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
changed the timeout value from 1000 jiffies to 1s. In the case where
HZ is 1000 the values are the same. However, for smaller HZ values the
timeout is now smaller, 1s instead of 10s in the case of HZ=100.

Since the timeout occurs in spite of a normal data transfer a timeout of
10s seems more appropriate. This restores the previous timeout in the
case where HZ=100 and results in an increase over the previous timeout
for larger values of HZ.

Fixes: f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[horms: rewrote changelog to refer to HZ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-05-06 11:58:33 +02:00
Linus Torvalds
d6a4c0e5d3 Merge branch 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine updates from Vinod Koul:

 - new drivers for:
        - Ingenic JZ4780 controller
        - APM X-Gene controller
        - Freescale RaidEngine device
        - Renesas USB Controller

  - remove device_alloc_chan_resources dummy handlers

  - sh driver cleanups for peri peri and related emmc and asoc patches
    as well

  - fixes and enhancements spread over the drivers

* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (59 commits)
  dmaengine: dw: don't prompt for DW_DMAC_CORE
  dmaengine: shdmac: avoid unused variable warnings
  dmaengine: fix platform_no_drv_owner.cocci warnings
  dmaengine: pch_dma: fix memory leak on failure path in pch_dma_probe()
  dmaengine: at_xdmac: unlock spin lock before return
  dmaengine: xgene: devm_ioremap() returns NULL on error
  dmaengine: xgene: buffer overflow in xgene_dma_init_channels()
  dmaengine: usb-dmac: Fix dereferencing freed memory 'desc'
  dmaengine: sa11x0: report slave capabilities to upper layers
  dmaengine: vdma: Fix compilation warnings
  dmaengine: fsl_raid: statify fsl_re_chan_probe
  dmaengine: Driver support for FSL RaidEngine device.
  dmaengine: xgene_dma_init_ring_mngr() can be static
  Documentation: dma: Add documentation for the APM X-Gene SoC DMA device DTS binding
  arm64: dts: Add APM X-Gene SoC DMA device and DMA clock DTS nodes
  dmaengine: Add support for APM X-Gene SoC DMA engine driver
  dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver
  dmaengine: renesas,usb-dmac: Add device tree bindings documentation
  dmaengine: edma: fixed wrongly initialized data parameter to the edma callback
  dmaengine: ste_dma40: fix implicit conversion
  ...
2015-04-24 09:49:37 -07:00
Kouichi Tomita
dbb42d962c mmc: sh_mmcif: Add exclusion between cmd and interrupt
A command end interrupt should not be processed between command issue
and setting of wait_for flag. It expects already the flag to be set.
Therefore the exclusive control was added.

Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-03-23 14:13:43 +01:00
Kouichi Tomita
4cbd522465 mmc: sh_mmcif: Move dev_err() of mmcif_timeout_work()
If interruption of command already occurred, mrq pointer in dev_err()
would refer to NULL, because the host-state is changed to STATE_IDLE
and mrq pointer is changed to NULL by interrupt handler.
Therefore dev_err is moved after checking STATE_IDLE.

Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-03-23 14:13:43 +01:00
Kuninori Morimoto
5f48dd0690 mmc: sh_mmcif: remove slave_id settings for DMAEngine
Current sh_mmcif sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-02-23 16:12:25 +05:30
Peter Griffin
2137f5d3b8 mmc: remove .owner field for drivers using module_platform_driver
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:04 +02:00