Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C.
This patch adds support for SPI interface for accessing STMPE's address space.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C and all code is present in a single file
stmpe.c. It would be better to separate out I2C interface specific code from
controller specific code. Later SPI specific code can be added in a separate
file.
This patch separates out I2C and controller specific code into separate files,
making stmpe.c independent of I2C.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8997 device does not support LED control function of it.
To enable MAX8997-LED driver, platform data and devices for LED are updated.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS65910 can be used without interrupts.
Hence let probe succeed in case interrupt can't be
configured and let Kernel only to complain about it
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL family of PMICs, used in master mode, have a power off
functionality. The resulting power off sequence shuts down all the SoC
supplies, LDOs, etc. The sequence is described in the datasheets
chapter "Power-Off Sequence".
Note, that board must be wired correctly for the power off to work as
expected.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add initial device-tree support for twl familly chips.
The current version is missing the regulator entries due
to the lack of DT regulator bindings for the moment.
Only the simple sub-modules that do not depend on
platform_data information can be initialized properly.
Add irqdomain support.
Add documentation for the Texas Instruments TWL Integrated Chip.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Balaji T K <balajitk@ti.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely@secretlab.ca: Fix IRQ_DOMAIN dependency in kconfig]
Cc: Grant Likely <grant.likely@secretlab.ca>
Got dropped in the regmap conversion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use gpio_request_one() instead of multiple gpiolib calls.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use gpio_request_one() instead of multiple gpiolib calls.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use gpio_request_one() instead of multiple gpiolib calls.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use gpio_request_one() instead of multiple gpiolib calls.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM1811A is a variant of the WM1811 with pin configuration changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the const keyword to fix below warning:
CC drivers/mfd/jz4740-adc.o
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_probe':
drivers/mfd/jz4740-adc.c:290: warning: passing argument 3 of 'mfd_add_devices' discards qualifiers from pointer target type
include/linux/mfd/core.h:93: note: expected 'struct mfd_cell *' but argument is of type 'const struct mfd_cell *'
Also make jz4740_adc_cells static, is not used outside
this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use device_init_wakeup & device_may_wakeup to init wakeup
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Silence following warnings:
WARNING: drivers/mfd/cs5535-mfd.o(.data+0x20): Section mismatch in
reference from the variable cs5535_mfd_drv to the function
.devinit.text:cs5535_mfd_probe()
The variable cs5535_mfd_drv references
the function __devinit cs5535_mfd_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/mfd/cs5535-mfd.o(.data+0x28): Section mismatch in
reference from the variable cs5535_mfd_drv to the function
.devexit.text:cs5535_mfd_remove()
The variable cs5535_mfd_drv references
the function __devexit cs5535_mfd_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Rename the variable from *_drv to *_driver so
modpost ignore the OK references to __devinit/__devexit
functions.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds device tree probe support for mc13xxx mfd driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make use of memory resources rather than hardcoded IO adresses.
This is a first step towards DT support.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As tertiary interrupts are handled by handle_twl4030_sih calling
handle_nested_irq, they do not need their own separate irq thread.
So mark them as 'nested_thread' interrupts to avoid the extra thread
creation.
Tested on GTA04 Pheonux.
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the ADC is being prepared for a single or multiple channel reading,
the adc0 register is reconfigured without taking the lithium cell, charge
current and battery current reading enable bits into account. Which results
in clearing the bits.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This will allow us to move to a more idiomatic MFD model as drivers
will be able to get the struct by looking at their parent device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Factors out some boilerplate code for drivers doing the default thing
for platform driver registration. Drivers using platform_driver_probe
or an initcall other than module_init can't be converted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a placeholder device tree binding for the wm8994 driver. At present
the binding is essentially null as none of the platform data is supported,
and at least some of that will depend on the pending regulator bindings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the 88pm860x normal bank register read/write to
use the register map API.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are two banks in 88pm8607. One is the normal bank, and the other
one is the test bank, it means it have the same register address in the
normal bank and test bank seperately.
For test bank register, it needs a special I2C sequence to acess as below,
Touching to 0xFA address
Touching to 0xFB address
Touching to 0xFF address
Accessing bank register
Touching to 0xFE address
Touching to 0xFC address
This sequence can't be interrupted. It means that we can't use
i2c_transfef() to implement touching 0xFA address. Otherwise, other i2c
operation may be inserted into 0xFA and 0xFB operation since the lock of
i2c_adapter is already released.
So for test bank we implemented specific i2c read/write operation;
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On many boards, stmpe is present as an separate device (not as part of SoC).
Here gpio lines are mostly used for getting interrupts. This patch adds in
support to handle irq over gpio pin.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Include linux/io.h to fix below build error:
CC drivers/mfd/jz4740-adc.o
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_irq_demux':
drivers/mfd/jz4740-adc.c:73: error: implicit declaration of function 'readb'
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_set_enabled':
drivers/mfd/jz4740-adc.c:110: error: implicit declaration of function 'writeb'
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_set_config':
drivers/mfd/jz4740-adc.c:146: error: implicit declaration of function 'readl'
drivers/mfd/jz4740-adc.c:151: error: implicit declaration of function 'writel'
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_probe':
drivers/mfd/jz4740-adc.c:249: error: implicit declaration of function 'ioremap_nocache'
drivers/mfd/jz4740-adc.c:249: warning: assignment makes pointer from integer without a cast
drivers/mfd/jz4740-adc.c:289: warning: passing argument 3 of 'mfd_add_devices' discards qualifiers from pointer target type
include/linux/mfd/core.h:93: note: expected 'struct mfd_cell *' but argument is of type 'const struct mfd_cell *'
drivers/mfd/jz4740-adc.c:299: error: implicit declaration of function 'iounmap'
make[2]: *** [drivers/mfd/jz4740-adc.o] Error 1
make[1]: *** [drivers/mfd] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_set_chained_handler sets 'desc->handle_irq'.
However this irq is called by handle_nested_irq from handle_twl4030_pih,
and that uses action->thread_fn.
So the handled set with irq_set_chained_handler is never called.
So change to use request_threaded_irq instead - that sets the correct field.
Tested on GTA04 Phoenux.
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As the interrupt source is only cleared by the threaded interrupt
service routine, we need to make the base interrupt IRQF_ONESHOT.
Without this, the first interrupt from the TWL4030 cause the CPU to
enter an infinite loop trying to handle to interrupt but never
clearing it.
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The function is not actually cleaing the bitmask.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix below build warning if CONFIG_DEBUG_FS is disabled.
CC drivers/mfd/ab8500-core.o
drivers/mfd/ab8500-core.c:623: warning: 'ab8500_debug_resources' defined but not used
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Check inuse variable before trying to access twl_map to prevent
dereferencing of uninitialized variable.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Include linux/module.h to fix below build error:
CC drivers/mfd/ab5500-debugfs.o
drivers/mfd/ab5500-debugfs.c:571: error: 'THIS_MODULE' undeclared here (not in a function)
make[2]: *** [drivers/mfd/ab5500-debugfs.o] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This didn't go in as part of the original MFD patch for WM1811 due to
cross tree issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It does not make sense to write new value only when all the bit_mask
bits are zero.
We need to write new value if the bit mask fields of new value is
not equal to old value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It does not make sense to write new value only when all the bit_mask
bits are zero.
We need to write new value if the bit mask fields of new value is
not equal to old value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code checks if all the bit_mask bits are all zero is wrong.
We need to write new value if the bit mask fields of new value is
not equal to old value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These files had implicit dependencies on modular support
which now show up as build failures with the module cleanup
work merged to mainline.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
