Commit 13bbbfbea7 ("bpf: Add bpf_dynptr_read and bpf_dynptr_write")
added the bpf_dynptr_write() and bpf_dynptr_read() APIs.
However, it will be needed for some dynptr types to pass in flags as
well (e.g. when writing to a skb, the user may like to invalidate the
hash or recompute the checksum).
This patch adds a "u64 flags" arg to the bpf_dynptr_read() and
bpf_dynptr_write() APIs before their UAPI signature freezes where
we then cannot change them anymore with a 5.19.x released kernel.
Fixes: 13bbbfbea7 ("bpf: Add bpf_dynptr_read and bpf_dynptr_write")
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20220706232547.4016651-1-joannelkoong@gmail.com
The byte queue limits (BQL) mechanism is intended to move queuing from
the driver to the network stack in order to reduce latency caused by
excessive queuing in hardware. However, when transmitting or redirecting
a packet using generic XDP, the qdisc layer is bypassed and there are no
additional queues. Since netif_xmit_stopped() also takes BQL limits into
account, but without having any alternative queuing, packets are
silently dropped.
This patch modifies the drop condition to only consider cases when the
driver itself cannot accept any more packets. This is analogous to the
condition in __dev_direct_xmit(). Dropped packets are also counted on
the device.
Bypassing the qdisc layer in the generic XDP TX path means that XDP
packets are able to starve other packets going through a qdisc, and
DDOS attacks will be more effective. In-driver-XDP use dedicated TX
queues, so they do not have this starvation issue.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220705082345.2494312-1-johan.almbladh@anyfinetworks.com
Mat Martineau says:
====================
mptcp: Path manager fixes for 5.19
The MPTCP userspace path manager is new in 5.19, and these patches fix
some issues in that new code.
Patches 1-3 fix path manager locking issues.
Patches 4 and 5 allow userspace path managers to change priority of
established subflows using the existing MPTCP_PM_CMD_SET_FLAGS generic
netlink command. Includes corresponding self test update.
Patches 6 and 7 fix accounting of available endpoint IDs and the
MPTCP_MIB_RMSUBFLOW counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases MPTCP_MIB_RMSUBFLOW mib counter in userspace pm
destroy subflow function mptcp_nl_cmd_sf_destroy() when removing subflow.
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mptcp_pm_nl_rm_addr_or_subflow() we always mark as available
the id corresponding to the just removed address.
The used bitmap actually tracks only the local IDs: we must
restrict the operation when a (local) subflow is removed.
Fixes: a88c9e4969 ("mptcp: do not block subflows creation on errors")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the testing sample (pm_nl_ctl) to exercise
the updated MPTCP_PM_CMD_SET_FLAGS command for userspace PMs to
issue MP_PRIO signals over the selected subflow.
E.g. ./pm_nl_ctl set 10.0.1.2 port 47234 flags backup token 823274047 rip 10.0.1.1 rport 50003
userspace_pm.sh has a new selftest that invokes this command.
Fixes: 259a834fad ("selftests: mptcp: functional tests for the userspace PM type")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Kishen Maloor <kishen.maloor@intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates MPTCP_PM_CMD_SET_FLAGS to allow userspace PMs
to issue MP_PRIO signals over a specific subflow selected by
the connection token, local and remote address+port.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/286
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Kishen Maloor <kishen.maloor@intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up a subflow's flags for sending MP_PRIO MPTCP options, the
subflow socket lock was not held while reading and modifying several
struct members that are also read and modified in mptcp_write_options().
Acquire the subflow socket lock earlier and send the MP_PRIO ACK with
that lock already acquired. Add a new variant of the
mptcp_subflow_send_ack() helper to use with the subflow lock held.
Fixes: 067065422f ("mptcp: add the outgoing MP_PRIO support")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The in-kernel path manager code for changing subflow flags acquired both
the msk socket lock and the PM lock when possibly changing the "backup"
and "fullmesh" flags. mptcp_pm_nl_mp_prio_send_ack() does not access
anything protected by the PM lock, and it must release and reacquire
the PM lock.
By pushing the PM lock to where it is needed in mptcp_pm_nl_fullmesh(),
the lock is only acquired when the fullmesh flag is changed and the
backup flag code no longer has to release and reacquire the PM lock. The
change in locking context requires the MIB update to be modified - move
that to a better location instead.
This change also makes it possible to call
mptcp_pm_nl_mp_prio_send_ack() for the userspace PM commands without
manipulating the in-kernel PM lock.
Fixes: 0f9f696a50 ("mptcp: add set_flags command in PM netlink")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user-space PM subflow removal path uses a couple of helpers
that must be called under the msk socket lock and the current
code lacks such requirement.
Change the existing lock scope so that the relevant code is under
its protection.
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/287
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov says:
====================
net: Fix police 'continue' action offload
TC act_police with 'continue' action had been supported by mlx5 matchall
classifier offload implementation for some time. However, 'continue' was
assumed implicitly and recently got broken in multiple places. Fix it in
both TC hardware offload validation code and mlx5 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Referenced commit prepared the code for upcoming extension that allows mlx5
to offload police action attached to flower classifier. However, with
regard to existing matchall classifier offload validation should be
reversed as FLOW_ACTION_CONTINUE is the only supported notexceed police
action type. Fix the problem by allowing FLOW_ACTION_CONTINUE for police
action and extend scan_tc_matchall_fdb_actions() to only allow such actions
with matchall classifier.
Fixes: d97b4b105c ("flow_offload: reject offload for all drivers with invalid police parameters")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading police with action TC_ACT_UNSPEC was erroneously disabled even
though it was supported by mlx5 matchall offload implementation, which
didn't verify the action type but instead assumed that any single police
action attached to matchall classifier is a 'continue' action. Lack of
action type check made it non-obvious what mlx5 matchall implementation
actually supports and caused implementers and reviewers of referenced
commits to disallow it as a part of improved validation code.
Fixes: b8cd5831c6 ("net: flow_offload: add tc police action parameters")
Fixes: b50e462bc2 ("net/sched: act_police: Add extack messages for offload failure")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of counting the child nodes in the device tree, hardcode the
number of ports in the driver itself. The counting won't work at all
if an ethernet port is marked as disabled, e.g. because it is not
connected on the board at all.
It turns out that the LAN9662 and LAN9668 use the same switching IP
with the same synthesis parameters. The only difference is that the
output ports are not connected. Thus, we can just hardcode the
number of physical ports to 8.
Fixes: db8bcaad53 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220704153654.1167886-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fix deadlock when powering on.
-----BEGIN PGP SIGNATURE-----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=hm0v
-----END PGP SIGNATURE-----
Merge tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix deadlock when powering on.
* tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: core: Fix deadlock on hci_power_on_sync.
====================
Link: https://lore.kernel.org/r/20220705202700.1689796-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
`cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
commit [1] to ensure that power_on work is canceled after HCI interface
down.
But, in certain cases power_on work function may call hci_dev_close_sync
itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
happens when device is rfkilled on boot. To avoid deadlock, move
power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.
Deadlock introduced by commit [1] was reported in [2,3] as broken
suspend. Suspend did not work because `hdev->req_lock` held as result of
`power_on` work deadlock. In fact, other BT features were not working.
It was not observed when testing [1] since it was verified without
rfkill in place.
NOTE: It is not needed to cancel power_on work from other places where
hci_dev_do_close/hci_dev_close_sync is called in case:
* Requests were serialized due to `hdev->req_workqueue`. The power_on
work is first in that workqueue.
* hci_rfkill_set_block which won't close device anyway until HCI_SETUP
is on.
* hci_sock_release which runs after hci_sock_bind which ensures
HCI_SETUP was cleared.
As result, behaviour is the same as in pre-dd06ed7 commit, except
power_on work cancel added to hci_dev_close.
[1]: commit ff7f292611 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
[2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
[2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/
Fixes: ff7f292611 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Reported-by: Max Krummenacher <max.krummenacher@toradex.com>
Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Vladimir Oltean says:
====================
Fix bridge_vlan_aware.sh and bridge_vlan_unaware.sh with IFF_UNICAST_FLT
Make sure that h1 and h2 don't drop packets with a random MAC DA, which
otherwise confuses these selftests. Also, fix an incorrect error message
found during those failures.
====================
Link: https://lore.kernel.org/r/20220703073626.937785-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When packets are not received, they aren't received on $host1_if, so the
message talking about the second host not receiving them is incorrect.
Fix it.
Fixes: d4deb01467 ("selftests: forwarding: Add a test for FDB learning")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The first host interface has by default no interest in receiving packets
MAC DA de:ad:be:ef:13:37, so it might drop them before they hit the tc
filter and this might confuse the selftest.
Enable promiscuous mode such that the filter properly counts received
packets.
Fixes: d4deb01467 ("selftests: forwarding: Add a test for FDB learning")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As mentioned in the blamed commit, flood_unicast_test() works by
checking the match count on a tc filter placed on the receiving
interface.
But the second host interface (host2_if) has no interest in receiving a
packet with MAC DA de:ad:be:ef:13:37, so its RX filter drops it even
before the ingress tc filter gets to be executed. So we will incorrectly
get the message "Packet was not flooded when should", when in fact, the
packet was flooded as expected but dropped due to an unrelated reason,
at some other layer on the receiving side.
Force h2 to accept this packet by temporarily placing it in promiscuous
mode. Alternatively we could either deliver to its MAC address or use
tcpdump_start, but this has the fewest complications.
This fixes the "flooding" test from bridge_vlan_aware.sh and
bridge_vlan_unaware.sh, which calls flood_test from the lib.
Fixes: 236dd50bf6 ("selftests: forwarding: Add a test for flooded traffic")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmLCxswTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXR27B/oDW8Z5VKdextQ5vrBmZM0Qo2FhY9Mj
fvK+6wzjYYlIXwXonc420CcRldEwlIgGrr41jr27gd04MTz82v12FQh/4je08wlJ
WZ/Vhn4AX7HSnNysEOakpEr/LKlm19vWsq0Z9KJpt9JGYKNxzJirvGHYNUop4erC
wXEHm31qRnll06I/38FMVUhSiY0K2ZfJRtWX0zopH3Jj7mwcDT8UaGXApEkhUvdS
7JRLsTmMGwAUsYuaoYl+VR186avBpvLHgkYTbZKBvQASd4DZY4LSqBJTpIcbB621
UK8bKIKmhSWOSyU/gnOjD86sacDcyvuKRuLUxYFuGKPyvtuiTYcXRVp9
=Qgal
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.19-20220704' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
can 2022-07-04
The 1st patch is by Oliver Hartkopp, targets the BCM CAN protocol and
converts a costly synchronize_rcu() to call_rcu() to fix a performance
regression.
Srinivas Neeli's patch for the xilinx_can driver drops the brp limit
down to 1, as only the pre-production silicon have an issue with a brp
of 1.
The next patch is by Duy Nguyen and fixes the data transmission on
R-Car V3U SoCs in the rcar_canfd driver.
Rhett Aultman's patch fixes a DMA memory leak in the gs_usb driver.
Liang He's patch removes an extra of_node_get() in the grcan driver.
The next 2 patches are by me, target the m_can driver and fix the
timestamp handling used for peripheral devices like the tcan4x5x.
Jimmy Assarsson contributes 3 patches for the kvaser_usb driver and
fixes CAN clock and bit timing related issues.
The remaining 5 patches target the mcp251xfd driver. Thomas Kopp
contributes 2 patches to improve the workaround for broken CRC when
reading the TBC register. 3 patches by me add a missing
hrtimer_cancel() during the ndo_stop() callback, and fix the reading
of the Device ID register.
* tag 'linux-can-fixes-for-5.19-20220704' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix endianness conversion
can: mcp251xfd: mcp251xfd_register_get_dev_id(): use correct length to read dev_id
can: mcp251xfd: mcp251xfd_stop(): add missing hrtimer_cancel()
can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on TBC register
can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for mcp2517fd
can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32 bits
can: m_can: m_can_chip_config(): actually enable internal timestamping
can: grcan: grcan_probe(): remove extra of_node_get()
can: gs_usb: gs_usb_open/close(): fix memory leak
can: rcar_canfd: Fix data transmission failed on R-Car V3U
Revert "can: xilinx_can: Limit CANFD brp to 2"
can: bcm: use call_rcu() instead of costly synchronize_rcu()
====================
Link: https://lore.kernel.org/r/20220704122613.1551119-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mcp251xfd_register_get_dev_id() the device ID register is read with
handcrafted SPI transfers. As all registers, this register is in
little endian. Further it is not naturally aligned in struct
mcp251xfd_map_buf_nocrc::data. However after the transfer the register
content is converted from big endian to CPU endianness not taking care
of being unaligned.
Fix the conversion by converting from little endian to CPU endianness
taking the unaligned source into account.
Side note: So far the register content is 0x0 on all mcp251xfd
compatible chips, and is only used for an informative printk.
Link: https://lore.kernel.org/all/20220627092859.809042-1-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device ID register is 32 bits wide. The driver uses incorrectly
the size of a pointer to a u32 to calculate the length of the SPI
transfer. This results in a read of 2 registers on 64 bit platforms.
This is no problem on the Linux side, as the RX buffer of the SPI
transfer is large enough. In the mpc251xfd chip this results in the
read of an undocumented register. So far no problems were observed.
Fix the length of the SPI transfer to read the device ID register
only.
Link: https://lore.kernel.org/all/20220616094914.244440-1-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit 169d00a256 ("can: mcp251xfd: add TX IRQ coalescing
support") software based TX coalescing was added to the driver. The
key idea is to keep the TX complete IRQ disabled for some time after
processing it and re-enable later by a hrtimer. When bringing the
interface down, this timer has to be stopped.
Add the missing hrtimer_cancel() of the tx_irq_time hrtimer to
mcp251xfd_stop().
Link: https://lore.kernel.org/all/20220620143942.891811-1-mkl@pengutronix.de
Fixes: 169d00a256 ("can: mcp251xfd: add TX IRQ coalescing support")
Cc: stable@vger.kernel.org # v5.18
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
New investigations and simulations indicate that the CRC send by the
device is calculated on correct data, and the data is incorrectly
received by the SPI host controller.
Use flipped instead of original data and update workaround description
in mcp251xfd_regmap_crc_read().
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
Measurements on the mcp2517fd show that the workaround is applicable
not only of the lowest byte is 0x00 or 0x80, but also if 3 least
significant bits are set.
Update check on 1st data byte and workaround description accordingly.
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Reported-by: Pavel Modilaynen <pavel.modilaynen@volvocars.com>
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use correct bittiming limits depending on device. For devices based on
USBcanII, Leaf M32C or Leaf i.MX28.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: b4f20130af ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe")
Fixes: f5d4abea3c ("can: kvaser_usb: Add support for the USBcan-II family")
Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: remove stray netlink.h include]
[mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The firmware of M32C based Leaf devices expects bittiming parameters
calculated for 16MHz clock. Since we use the actual clock frequency of
the device, the device may end up with wrong bittiming parameters,
depending on user requested parameters.
This regression affects M32C based Leaf devices with non-16MHz clock.
Fixes: fb12797ab1 ("can: kvaser_usb: get CAN clock frequency from device")
Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Unify and move compile-time known information into new struct
kvaser_usb_driver_info, in favor of run-time checks.
All Kvaser USBcanII supports listen-only mode and error counter
reporting.
Link: https://lore.kernel.org/all/20220603083820.800246-2-extja@kvaser.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: move struct kvaser_usb_driver_info into kvaser_usb_core.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During a reset, there may have been transmits in flight that are no
longer valid and cannot be fulfilled. Resetting and clearing the
queues is insufficient; each skb also needs to be explicitly freed
so that upper levels are not left waiting for confirmation of a
transmit that will never happen. If this happens frequently enough,
the apparent backlog will cause TCP to begin "congestion control"
unnecessarily, culminating in permanently decreased throughput.
Fixes: d7c0ef36bd ("ibmvnic: Free and re-allocate scrqs when tx/rx scrqs change")
Tested-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Rick Lindsley <ricklind@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1be37d3b04 ("can: m_can: fix periph RX path: use
rx-offload to ensure skbs are sent from softirq context") the RX path
for peripheral devices was switched to RX-offload.
Received CAN frames are pushed to RX-offload together with a
timestamp. RX-offload is designed to handle overflows of the timestamp
correctly, if 32 bit timestamps are provided.
The timestamps of m_can core are only 16 bits wide. So this patch
shifts them to full 32 bit before passing them to RX-offload.
Link: https://lore.kernel.org/all/20220612211410.4081390-1-mkl@pengutronix.de
Fixes: 1be37d3b04 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit df06fd6782 ("can: m_can: m_can_chip_config(): enable and
configure internal timestamps") the timestamping in the m_can core
should be enabled. In peripheral mode, the RX'ed CAN frames, TX
compete frames and error events are sorted by the timestamp.
The above mentioned commit however forgot to enable the timestamping.
Add the missing bits to enable the timestamp counter to the write of
the Timestamp Counter Configuration register.
Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de
Fixes: df06fd6782 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In grcan_probe(), of_find_node_by_path() has already increased the
refcount. There is no need to call of_node_get() again, so remove it.
Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com
Fixes: 1e93ed26ac ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs")
Cc: stable@vger.kernel.org # v5.18
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the 928150fad4 ("can: esd_usb2: fix memory
leak").
Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On R-Car V3U, this driver should use suitable register offset instead of
other SoCs' one. Otherwise, data transmission failed on R-Car V3U.
Fixes: 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Link: https://lore.kernel.org/all/20220704074611.957191-1-yoshihiro.shimoda.uh@renesas.com
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit 05ca14fdb6.
On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.
Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jakub Kicinski says:
====================
docs: netdev: document more of our rules
The patch series length limit and reverse xmas tree are not documented.
Add those, and a tl;dr section summarizing how we differ.
v2: improve the series length blurb (Andrew)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Summarize the rules we see broken most often and which may
be less familiar to kernel devs who are used to working outside
of netdev.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the 15 patch rule the reverse xmas tree is not
documented.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had been asking people to avoid massive patch series but it does
not appear in the FAQ.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d5f9023fa6 ("can: bcm: delay release of struct bcm_op
after synchronize_rcu()") Thadeu Lima de Souza Cascardo introduced two
synchronize_rcu() calls in bcm_release() (only once at socket close)
and in bcm_delete_rx_op() (called on removal of each single bcm_op).
Unfortunately this slow removal of the bcm_op's affects user space
applications like cansniffer where the modification of a filter
removes 2048 bcm_op's which blocks the cansniffer application for
40(!) seconds.
In commit 181d444790 ("can: gw: use call_rcu() instead of costly
synchronize_rcu()") Eric Dumazet replaced the synchronize_rcu() calls
with several call_rcu()'s to safely remove the data structures after
the removal of CAN ID subscriptions with can_rx_unregister() calls.
This patch adopts Erics approach for the can-bcm which should be
applicable since the removal of tasklet_kill() in bcm_remove_op() and
the introduction of the HRTIMER_MODE_SOFT timer handling in Linux 5.4.
Fixes: d5f9023fa6 ("can: bcm: delay release of struct bcm_op after synchronize_rcu()") # >= 5.4
Link: https://lore.kernel.org/all/20220520183239.19111-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Eric Dumazet <edumazet@google.com>
Cc: Norbert Slusarek <nslusarek@gmx.net>
Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Insufficient validation of element datatype and length in
nft_setelem_parse_data(). At least commit 7d7402642e updates
maximum element data area up to 64 bytes when only 16 bytes
where supported at the time. Support for larger element size
came later in fdb9c405e3 though. Picking this older commit
as Fixes: tag to be safe than sorry.
2) Memleak in pipapo destroy path, reproducible when transaction
in aborted. This is already triggering in the existing netfilter
test infrastructure since more recent new tests are covering this
path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
New elements that reside in the clone are not released in case that the
transaction is aborted.
[16302.231754] ------------[ cut here ]------------
[16302.231756] WARNING: CPU: 0 PID: 100509 at net/netfilter/nf_tables_api.c:1864 nf_tables_chain_destroy+0x26/0x127 [nf_tables]
[...]
[16302.231882] CPU: 0 PID: 100509 Comm: nft Tainted: G W 5.19.0-rc3+ #155
[...]
[16302.231887] RIP: 0010:nf_tables_chain_destroy+0x26/0x127 [nf_tables]
[16302.231899] Code: f3 fe ff ff 41 55 41 54 55 53 48 8b 6f 10 48 89 fb 48 c7 c7 82 96 d9 a0 8b 55 50 48 8b 75 58 e8 de f5 92 e0 83 7d 50 00 74 09 <0f> 0b 5b 5d 41 5c 41 5d c3 4c 8b 65 00 48 8b 7d 08 49 39 fc 74 05
[...]
[16302.231917] Call Trace:
[16302.231919] <TASK>
[16302.231921] __nf_tables_abort.cold+0x23/0x28 [nf_tables]
[16302.231934] nf_tables_abort+0x30/0x50 [nf_tables]
[16302.231946] nfnetlink_rcv_batch+0x41a/0x840 [nfnetlink]
[16302.231952] ? __nla_validate_parse+0x48/0x190
[16302.231959] nfnetlink_rcv+0x110/0x129 [nfnetlink]
[16302.231963] netlink_unicast+0x211/0x340
[16302.231969] netlink_sendmsg+0x21e/0x460
Add nft_set_pipapo_match_destroy() helper function to release the
elements in the lookup tables.
Stefano Brivio says: "We additionally look for elements pointers in the
cloned matching data if priv->dirty is set, because that means that
cloned data might point to additional elements we did not commit to the
working copy yet (such as the abort path case, but perhaps not limited
to it)."
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make sure element data type and length do not mismatch the one specified
by the set declaration.
Fixes: 7d7402642e ("netfilter: nf_tables: variable sized set element keys / data")
Reported-by: Hugues ANGUELKOV <hanguelkov@randorisec.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add Wenjia as maintainer for Shared Memory Communications (SMC)
Sockets.
Acked-by: Wenjia Zhang <wenjia@linux.ibm.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8fffa0e345 ("selftests/bpf: Normalize XDP section names in
selftests") the xdp_dummy.o's section name has changed to xdp. But some
tests are still using "section xdp_dummy", which make the tests failed.
Fix them by updating to the new section name.
Fixes: 8fffa0e345 ("selftests/bpf: Normalize XDP section names in selftests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20220630062228.3453016-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2022-07-02
We've added 7 non-merge commits during the last 14 day(s) which contain
a total of 6 files changed, 193 insertions(+), 86 deletions(-).
The main changes are:
1) Fix clearing of page contiguity when unmapping XSK pool, from Ivan Malov.
2) Two verifier fixes around bounds data propagation, from Daniel Borkmann.
3) Fix fprobe sample module's parameter descriptions, from Masami Hiramatsu.
4) General BPF maintainer entry revamp to better scale patch reviews.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, selftests: Add verifier test case for jmp32's jeq/jne
bpf, selftests: Add verifier test case for imm=0,umin=0,umax=1 scalar
bpf: Fix insufficient bounds propagation from adjust_scalar_min_max_vals
bpf: Fix incorrect verifier simulation around jmp32's jeq/jne
xsk: Clear page contiguity bit when unmapping pool
bpf, docs: Better scale maintenance of BPF subsystem
fprobe, samples: Add module parameter descriptions
====================
Link: https://lore.kernel.org/r/20220701230121.10354-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a test case to trigger the verifier's incorrect conclusion in the
case of jmp32's jeq/jne. Also here, make use of dead code elimination,
so that we can see the verifier bailing out on unfixed kernels.
Before:
# ./test_verifier 724
#724/p jeq32/jne32: bounds checking FAIL
Failed to load prog 'Permission denied'!
R4 !read_ok
verification time 8 usec
stack depth 0
processed 8 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 0
Summary: 0 PASSED, 0 SKIPPED, 1 FAILED
After:
# ./test_verifier 724
#724/p jeq32/jne32: bounds checking OK
Summary: 1 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220701124727.11153-4-daniel@iogearbox.net
Add a test case to trigger the constant scalar issue which leaves the
register in scalar(imm=0,umin=0,umax=1,var_off=(0x0; 0x0)) state. Make
use of dead code elimination, so that we can see the verifier bailing
out on unfixed kernels. For the condition, we use jle given it checks
on umax bound.
Before:
# ./test_verifier 743
#743/p jump & dead code elimination FAIL
Failed to load prog 'Permission denied'!
R4 !read_ok
verification time 11 usec
stack depth 0
processed 13 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1
Summary: 0 PASSED, 0 SKIPPED, 1 FAILED
After:
# ./test_verifier 743
#743/p jump & dead code elimination OK
Summary: 1 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220701124727.11153-3-daniel@iogearbox.net
