The interrupt line of PCI devices is interpreted as edge-triggered,
however the interrupt signal of the m_can controller integrated in Intel
Elkhart Lake CPUs appears to be generated level-triggered.
Consider the following sequence of events:
- IR register is read, interrupt X is set
- A new interrupt Y is triggered in the m_can controller
- IR register is written to acknowledge interrupt X. Y remains set in IR
As at no point in this sequence no interrupt flag is set in IR, the
m_can interrupt line will never become deasserted, and no edge will ever
be observed to trigger another run of the ISR. This was observed to
result in the TX queue of the EHL m_can to get stuck under high load,
because frames were queued to the hardware in m_can_start_xmit(), but
m_can_finish_tx() was never run to account for their successful
transmission.
On an Elkhart Lake based board with the two CAN interfaces connected to
each other, the following script can reproduce the issue:
ip link set can0 up type can bitrate 1000000
ip link set can1 up type can bitrate 1000000
cangen can0 -g 2 -I 000 -L 8 &
cangen can0 -g 2 -I 001 -L 8 &
cangen can0 -g 2 -I 002 -L 8 &
cangen can0 -g 2 -I 003 -L 8 &
cangen can0 -g 2 -I 004 -L 8 &
cangen can0 -g 2 -I 005 -L 8 &
cangen can0 -g 2 -I 006 -L 8 &
cangen can0 -g 2 -I 007 -L 8 &
cangen can1 -g 2 -I 100 -L 8 &
cangen can1 -g 2 -I 101 -L 8 &
cangen can1 -g 2 -I 102 -L 8 &
cangen can1 -g 2 -I 103 -L 8 &
cangen can1 -g 2 -I 104 -L 8 &
cangen can1 -g 2 -I 105 -L 8 &
cangen can1 -g 2 -I 106 -L 8 &
cangen can1 -g 2 -I 107 -L 8 &
stress-ng --matrix 0 &
To fix the issue, repeatedly read and acknowledge interrupts at the
start of the ISR until no interrupt flags are set, so the next incoming
interrupt will also result in an edge on the interrupt line.
While we have received a report that even with this patch, the TX queue
can become stuck under certain (currently unknown) circumstances on the
Elkhart Lake, this patch completely fixes the issue with the above
reproducer, and it is unclear whether the remaining issue has a similar
cause at all.
Fixes: cab7ffc032 ("can: m_can: add PCI glue driver for Intel Elkhart Lake")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/fdf0439c51bcb3a46c21e9fb21c7f1d06363be84.1728288535.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While an m_can controller usually already has the init flag from a
hardware reset, no such reset happens on the integrated m_can_pci of the
Intel Elkhart Lake. If the CAN controller is found in an active state,
m_can_dev_setup() would fail because m_can_niso_supported() calls
m_can_cccr_update_bits(), which refuses to modify any other configuration
bits when CCCR_INIT is not set.
To avoid this issue, set CCCR_INIT before attempting to modify any other
configuration flags.
Fixes: cd5a46ce6f ("can: m_can: don't enable transceiver when probing")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/e247f331cb72829fcbdfda74f31a59cbad1a6006.1728288535.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
get resource + request_mem_region + ioremap can all be done by a single
function.
Replace them with devm_platform_get_and_ioremap_resource or\
devm_platform_ioremap_resource where res is not used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> # sja1000_platform.c
Link: https://patch.msgid.link/20241203231337.182391-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently rtnl_link_get_net_ifla() gets called twice when we create
peer devices, once in rtnl_add_peer_net() and once in each ->newlink()
implementation.
This looks safer, however, it leads to a classic Time-of-Check to
Time-of-Use (TOCTOU) bug since IFLA_NET_NS_PID is very dynamic. And
because of the lack of checking error pointer of the second call, it
also leads to a kernel crash as reported by syzbot.
Fix this by getting rid of the second call, which already becomes
redudant after Kuniyuki's work. We have to propagate the result of the
first rtnl_link_get_net_ifla() down to each ->newlink().
Reported-by: syzbot+21ba4d5adff0b6a7cfc6@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=21ba4d5adff0b6a7cfc6
Fixes: 0eb87b02a7 ("veth: Set VETH_INFO_PEER to veth_link_ops.peer_type.")
Fixes: 6b84e558e9 ("vxcan: Set VXCAN_INFO_PEER to vxcan_link_ops.peer_type.")
Fixes: fefd5d0821 ("netkit: Set IFLA_NETKIT_PEER_INFO to netkit_link_ops.peer_type.")
Cc: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241129212519.825567-1-xiyou.wangcong@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround
broken TEF FIFO tail index erratum") introduced
mcp251xfd_get_tef_len() to get the number of unhandled transmit events
from the Transmit Event FIFO (TEF).
As the TEF has no head index, the driver uses the TX-FIFO's tail index
instead, assuming that send frames are completed.
When calculating the number of unhandled TEF events, that commit
didn't take mcp2518fd erratum DS80000789E 6. into account. According
to that erratum, the FIFOCI bits of a FIFOSTA register, here the
TX-FIFO tail index might be corrupted.
However here it seems the bit indicating that the TX-FIFO is
empty (MCP251XFD_REG_FIFOSTA_TFERFFIF) is not correct while the
TX-FIFO tail index is.
Assume that the TX-FIFO is indeed empty if:
- Chip's head and tail index are equal (len == 0).
- The TX-FIFO is less than half full.
(The TX-FIFO empty case has already been checked at the
beginning of this function.)
- No free buffers in the TX ring.
If the TX-FIFO is assumed to be empty, assume that the TEF is full and
return the number of elements in the TX-FIFO (which equals the number
of TEF elements).
If these assumptions are false, the driver might read to many objects
from the TEF. mcp251xfd_handle_tefif_one() checks the sequence numbers
and will refuse to process old events.
Reported-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Closes: https://patch.msgid.link/CAJ7t6HgaeQ3a_OtfszezU=zB-FqiZXqrnATJ3UujNoQJJf7GgA@mail.gmail.com
Fixes: b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround broken TEF FIFO tail index erratum")
Tested-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20241126-mcp251xfd-fix-length-calculation-v2-1-c2ed516ed6ba@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The f81604_handle_can_bus_errors() function only incremented the receive
error counter and never the transmit error counter, even if the ECC_DIR
flag reported that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 88da174369 ("can: usb: f81604: add Fintek F81604 support")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-13-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ems_usb_rx_err() function only incremented the receive error counter
and never the transmit error counter, even if the ECC_DIR flag reported
that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-12-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sun4i_can_err() function only incremented the receive error counter
and never the transmit error counter, even if the STA_ERR_DIR flag
reported that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
STA_ERR_DIR flag.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sja1000_err() function only incremented the receive error counter
and never the transmit error counter, even if the ECC_DIR flag reported
that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 429da1cc84 ("can: Driver for the SJA1000 CAN controller")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-10-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hi3110_can_ist() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission.
The fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: 57e83fb9b7 ("can: hi311x: Add Holt HI-311x CAN driver")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ifi_canfd_handle_lec_err() function was incorrectly incrementing only
the receive error counter, even in cases of bit or acknowledgment errors
that occur during transmission.
Fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: 5bbd655a8b ("can: ifi: Add more detailed error reporting")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/20241122221650.633981-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The m_can_handle_lec_err() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission.
Fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ensure that the statistics related to state error counters
(i. e. warning, passive, and bus-off) are updated even in case the skb
allocation fails. Additionally, also handle bus-off state is now.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The commit a22bd630cf ("can: hi311x: do not report txerr and rxerr
during bus-off") removed the reporting of rxerr and txerr even in case
of correct operation (i. e. not bus-off).
The error count information added to the CAN frame after netif_rx() is
a potential use after free, since there is no guarantee that the skb
is in the same state. It might be freed or reused.
Fix the issue by postponing the netif_rx() call in case of txerr and
rxerr reporting.
Fixes: a22bd630cf ("can: hi311x: do not report txerr and rxerr during bus-off")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-5-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Call the function can_change_state() if the allocation of the skb
fails, as it handles the cf parameter when it is null.
Additionally, this ensures that the statistics related to state error
counters (i. e. warning, passive, and bus-off) are updated.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is an approach made to implement gs_usb firmware/driver based on
Zephyr RTOS. It was found that USB stack of Zephyr RTOS overwrites USB
EP addresses, if they have different last 4 bytes in absence of other
endpoints.
For example in case of gs_usb candlelight firmware EP-IN is 0x81 and
EP-OUT 0x02. If there are no additional USB endpoints, Zephyr RTOS will
overwrite EP-OUT to 0x01. More information can be found in the
discussion with Zephyr RTOS USB stack maintainer here:
https://github.com/zephyrproject-rtos/zephyr/issues/67812
There are already two different gs_usb FW driver implementations based
on Zephyr RTOS:
1. https://github.com/CANnectivity/cannectivity
(by: https://github.com/henrikbrixandersen)
2. https://github.com/zephyrproject-rtos/zephyr/compare/main...KozhinovAlexander:zephyr:gs_usb
(by: https://github.com/KozhinovAlexander)
At the moment both Zephyr RTOS implementations use dummy USB endpoint,
to overcome described USB stack behavior from Zephyr itself. Since
Zephyr RTOS is intended to be used on microcontrollers with very
constrained amount of resources (ROM, RAM) and additional endpoint
requires memory, it is more convenient to update the gs_usb driver in
the Linux kernel.
To fix this problem, update the gs_usb driver from using hard coded
endpoint numbers to evaluate the endpoint descriptors and use the
endpoints provided there.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Alexander Kozhinov <ak.alexander.kozhinov@gmail.com>
Link: https://patch.msgid.link/20241018212450.31746-1-ak.alexander.kozhinov@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit 6e86a1543c ("can: dev: provide optional GPIO based
termination support") GPIO based termination support was added.
For no particular reason that patch uses gpiod_set_value() to set the
GPIO. This leads to the following warning, if the systems uses a
sleeping GPIO, i.e. behind an I2C port expander:
| WARNING: CPU: 0 PID: 379 at /drivers/gpio/gpiolib.c:3496 gpiod_set_value+0x50/0x6c
| CPU: 0 UID: 0 PID: 379 Comm: ip Not tainted 6.11.0-20241016-1 #1 823affae360cc91126e4d316d7a614a8bf86236c
Replace gpiod_set_value() by gpiod_set_value_cansleep() to allow the
use of sleeping GPIOs.
Cc: Nicolai Buchwitz <nb@tipi-net.de>
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reported-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Tested-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Fixes: 6e86a1543c ("can: dev: provide optional GPIO based termination support")
Link: https://patch.msgid.link/20241121-dev-fix-can_set_termination-v1-1-41fa6e29216d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For per-netns RTNL, we need to prefetch the peer device's netns.
Let's set rtnl_link_ops.peer_type and accordingly remove duplicated
validation in ->newlink().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241108004823.29419-8-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround
broken TEF FIFO tail index erratum") introduced
mcp251xfd_get_tef_len() to get the number of unhandled transmit events
from the Transmit Event FIFO (TEF).
As the TEF has no head pointer, the driver uses the TX FIFO's tail
pointer instead, assuming that send frames are completed. However the
check for the TEF being full was not correct. This leads to the driver
stop working if the TEF is full.
Fix the TEF full check by assuming that if, from the driver's point of
view, there are no free TX buffers in the chip and the TX FIFO is
empty, all messages must have been sent and the TEF must therefore be
full.
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Closes: https://patch.msgid.link/FR3P281MB155216711EFF900AD9791B7ED9692@FR3P281MB1552.DEUP281.PROD.OUTLOOK.COM
Fixes: b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround broken TEF FIFO tail index erratum")
Tested-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20241104-mcp251xfd-fix-length-calculation-v3-1-608b6e7e2197@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 50ea5449c5 ("can: mcp251xfd: fix ring configuration
when switching from CAN-CC to CAN-FD mode"), the current ring and
coalescing configuration is passed to can_ram_get_layout(). That fixed
the issue when switching between CAN-CC and CAN-FD mode with
configured ring (rx, tx) and/or coalescing parameters (rx-frames-irq,
tx-frames-irq).
However 50ea5449c5 ("can: mcp251xfd: fix ring configuration when
switching from CAN-CC to CAN-FD mode"), introduced a regression when
switching CAN modes with disabled coalescing configuration: Even if
the previous CAN mode has no coalescing configured, the new mode is
configured with active coalescing. This leads to delayed receiving of
CAN-FD frames.
This comes from the fact, that ethtool uses usecs = 0 and max_frames =
1 to disable coalescing, however the driver uses internally
priv->{rx,tx}_obj_num_coalesce_irq = 0 to indicate disabled
coalescing.
Fix the regression by assigning struct ethtool_coalesce
ec->{rx,tx}_max_coalesced_frames_irq = 1 if coalescing is disabled in
the driver as can_ram_get_layout() expects this.
Reported-by: https://github.com/vdh-robothania
Closes: https://github.com/raspberrypi/linux/issues/6407
Fixes: 50ea5449c5 ("can: mcp251xfd: fix ring configuration when switching from CAN-CC to CAN-FD mode")
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241025-mcp251xfd-fix-coalesing-v1-1-9d11416de1df@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), OF
can be enabled on all architectures. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20241022130439.70d016e9@endymion.delvare
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Rockchip CAN-FD controller is only present on Rockchip SoCs. Hence
add a dependency on ARCH_ROCKCHIP, to prevent asking the user about
this driver when configuring a kernel without Rockchip platform
support.
Fixes: ff60bfbaf6 ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/a4b3c8c1cca9515e67adac83af5ba1b1fab2fcbc.1727169288.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The c_can_handle_bus_err() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission. The patch fixes the issue by incrementing the
appropriate counter based on the type of error.
Fixes: 881ff67ad4 ("can: c_can: Added support for Bosch C_CAN controller")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241014135319.2009782-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit b382380c0d ("can: m_can: Add hrtimer to generate software
interrupt") support for IRQ-less devices was added. Instead of an
interrupt, the interrupt routine is called by a hrtimer-based polling
loop.
That patch forgot to change free_irq() to be only called for devices
with IRQs. Fix this, by calling free_irq() conditionally only if an
IRQ is available for the device (and thus has been requested
previously).
Fixes: b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20240930-m_can-cleanups-v1-1-001c579cdee4@pengutronix.de
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ISA variable is only defined if X86_32 is also defined. However,
these drivers are still useful and in use on at least some modern 64-bit
x86 industrial systems as well. With the correct module parameters, they
work as long as IO port communication is possible, despite their name
having ISA in them.
Fixes: a29689e60e ("net: handle HAS_IOPORT dependencies")
Signed-off-by: Thomas Mühlbacher <tmuehlbacher@posteo.net>
Link: https://patch.msgid.link/20240919174151.15473-2-tmuehlbacher@posteo.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
After calling m_can_stop() an interrupt may be pending or NAPI might
still be executed. This means the driver might still touch registers
of the IP core after the clocks have been disabled. This is not good
practice and might lead to aborts depending on the SoC integration.
To avoid these potential problems, make m_can_close() symmetric to
m_can_open(), i.e. stop the clocks at the end, right before shutting
down the transceiver.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-2-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If an interrupt (RX-complete or error flag) is set when bringing up
the CAN device, e.g. due to CAN bus traffic before initializing the
device, when m_can_start() is called and interrupts are enabled,
m_can_isr() is called immediately, which disables all CAN interrupts
and calls napi_schedule().
Because napi_enable() isn't called until later in m_can_open(), the
call to napi_schedule() never schedules the m_can_poll() callback and
the device is left with interrupts disabled and can't receive any CAN
packets until rebooted.
This can be verified by running "cansend" from another device before
setting the bitrate and calling "ip link set up can0" on the test
device. Adding debug lines to m_can_isr() shows it's called with flags
(IR_EP | IR_EW | IR_CRCE), which calls m_can_disable_all_interrupts()
and napi_schedule(), and then m_can_poll() is never called.
Move the call to napi_enable() above the call to m_can_start() to
enable any initial interrupt flags to be handled by m_can_poll() so
that interrupts are reenabled. Add a call to napi_disable() in the
error handling section of m_can_open(), to handle the case where later
functions return errors.
Also, in m_can_close(), move the call to napi_disable() below the call
to m_can_stop() to ensure all interrupts are handled when bringing
down the device. This race condition is much less likely to occur.
Tested on a Microchip SAMA7G54 MPU. The fix should be applicable to
any SoC with a Bosch M_CAN controller.
Signed-off-by: Jake Hamby <Jake.Hamby@Teledyne.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-1-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enabling 64-bit addressing for DMA buffers will prevent issues
on some memory constrained platforms like e.g. Raspberry Pi 5,
where the driver won't load because it cannot allocate enough
continuous memory in the default 32-bit memory address range.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://patch.msgid.link/d7340f78e3db305bfeeb8229d2dd1c9077e10b92.1725875278.git.martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove the CAN_CTRLMODE_3_SAMPLES announcement for CAN-USB/3-FD devices
because these devices don't support it.
The hardware has a Microchip SAM E70 microcontroller that uses a Bosch
MCAN IP core as CAN FD controller. But this MCAN core doesn't support
triple sampling.
Fixes: 80662d9430 ("can: esd_usb: Add support for esd CAN-USB/3")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20240904222740.2985864-2-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all can drivers to use .remove(), with the eventual goal to drop
struct platform_driver::remove_new(). As .remove() and .remove_new() have
the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20240909072742.381003-2-u.kleine-koenig@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On some 32-bit platforms (at least on parisc), the compiler generates
a call to __divdi3() from the u32 by 3 division in
rkcanfd_timestamp_init(), which results in the following linker
error:
| ERROR: modpost: "__divdi3" [drivers/net/can/rockchip/rockchip_canfd.ko] undefined!
As this code doesn't run in the hot path, a 64 bit by 32 bit division
is OK, even on 32 bit platforms. Use an explicit call to div_u64() to
fix linking.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409072304.lCQWyNLU-lkp@intel.com/
Link: https://patch.msgid.link/20240909-can-rockchip_canfd-fix-64-bit-division-v1-1-2748d9422b00@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
drivers/net/can/rockchip/rockchip_canfd-core.c:770:20: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
770 | .ndo_start_xmit = rkcanfd_start_xmit,
| ^~~~~~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int' (although the types are ABI compatible). Adjust
the return type of rkcanfd_start_xmit() to match the prototype's to
resolve the warning.
Fixes: ff60bfbaf6 ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20240906-rockchip-canfd-wifpts-v1-1-b1398da865b7@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use of the typed property accessors is preferred over of_get_property().
The existing code doesn't work on little endian systems either. Replace
the of_get_property() calls with of_property_read_bool() and
of_property_read_u32().
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240903135731.405635-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous commit prepared the TX path to make use of the full
TX-FIFO depth as much as possible. Increase the available TX-FIFO
depth to the hardware maximum of 2.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-17-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
So far the TX-FIFO is only used with a depth of 1, although the
hardware offers a depth of 2.
The workaround for the chips that are affected by erratum 6, i.e. EFF
frames may be send as standard frames, is to re-send the EFF frame.
This means the driver cannot queue the next frame for sending, as long
ad the EFF frame has not been successfully send out.
Introduce rkcanfd_get_effective_tx_free() that returns "0" space in
the TX-FIFO if an EFF frame is pending and the actual free space in
the TX-FIFO otherwise. Then replace rkcanfd_get_tx_free() with
rkcanfd_get_effective_tx_free() everywhere.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-16-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver contains workarounds for some of the rk3568v2 errata. Add
ethtool-based statistics ("ethtool -S") to track how often an erratum
workaround was needed.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-15-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tests show that sometimes both CAN bus error counters read 0x0, even
if the controller is in warning mode
(RKCANFD_REG_STATE_ERROR_WARNING_STATE in RKCANFD_REG_STATE
set).
To work around this issue, if both error counters read from hardware
are 0x0, use the structure priv->bec, otherwise save the read value in
priv->bec.
In rkcanfd_handle_rx_int_one() decrement the priv->bec.rxerr for
successfully RX'ed CAN frames.
In rkcanfd_handle_tx_done_one() decrement the priv->bec.txerr for
successfully TX'ed CAN frames.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-14-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| A dominant bit at the third bit of the intermission may cause a
| transmission error.
|
| When sampling the third bit of the intermission as a dominant bit, if
| tx_req is configured to transmit extended frames at this time, the
| extended frame may be sent to the bus in the format of a standard
| frame. The extended frame will be sent as a standard frame and will not
| result in error frames
Turn on "Interframe Spaceing RX Mode" only during TX to work around
erratum 12, according to rock-chip:
| Spaceing RX Mode = 1, the third Bit between frames cannot receive
| and send, and the fourth Bit begins to receive and send.
|
| Spaceing RX Mode = 0, allowing the third Bit between frames to
| receive and send.
Message-ID: <be72939f-0a9e-0608-dfff-7b0096a26eba@rock-chips.com>
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-13-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
