Sometimes, if the port doesn't work, we can try to fix it by resetting it.
This patch supports reset triggered by ethtool or FLR of PCIe, For example:
ethtool --reset eth0 dedicated
echo 1 > /sys/bus/pci/devices/0000\:83\:00.1/reset
We hope that the reset can be performed only when the port is down,
and the port cannot be up during the reset.
Therefore, the entire reset process is protected by the rtnl lock.
After the reset is complete, the hardware registers are restored
to their default values. Therefore, some rebuild operations are
required to rewrite the user configuration to the registers.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241216040532.1566229-7-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MAC can automatically send or respond to pause frames.
This patch supports the function of enabling pause frames
by using ethtool.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241216040532.1566229-6-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dump register is an effective way to analyze problems.
To ensure code flexibility, each register contains the type,
offset, and value information. The ethtool does the pretty print
based on these information.
The driver can dynamically add or delete registers that need to be dumped
in the future because information such as type and offset is contained.
ethtool always can do pretty print.
With the ethtool of a specific version,
the following effects are achieved:
[root@localhost sjj]# ./ethtool -d enp131s0f1
[SPEC] VALID [0x0000]: 0x00000001
[SPEC] EVENT_REQ [0x0004]: 0x00000000
[SPEC] MAC_ID [0x0008]: 0x00000002
[SPEC] PHY_ADDR [0x000c]: 0x00000002
[SPEC] MAC_ADDR_L [0x0010]: 0x00000808
[SPEC] MAC_ADDR_H [0x0014]: 0x08080802
[SPEC] UC_MAX_NUM [0x0018]: 0x00000004
[SPEC] MAX_MTU [0x0028]: 0x00000fc2
[SPEC] MIN_MTU [0x002c]: 0x00000100
[SPEC] TX_FIFO_NUM [0x0030]: 0x00000040
[SPEC] RX_FIFO_NUM [0x0034]: 0x0000007f
[SPEC] VLAN_LAYERS [0x0038]: 0x00000002
[MDIO] COMMAND_REG [0x0000]: 0x0000185f
[MDIO] ADDR_REG [0x0004]: 0x00000000
[MDIO] WDATA_REG [0x0008]: 0x0000a000
[MDIO] RDATA_REG [0x000c]: 0x00000000
[MDIO] STA_REG [0x0010]: 0x00000000
[GMAC] DUPLEX_TYPE [0x0008]: 0x00000001
[GMAC] FD_FC_TYPE [0x000c]: 0x00008808
[GMAC] FC_TX_TIMER [0x001c]: 0x000000ff
[GMAC] FD_FC_ADDR_LOW [0x0020]: 0xc2000001
[GMAC] FD_FC_ADDR_HIGH [0x0024]: 0x00000180
[GMAC] MAX_FRM_SIZE [0x003c]: 0x000005f6
[GMAC] PORT_MODE [0x0040]: 0x00000002
[GMAC] PORT_EN [0x0044]: 0x00000006
...
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241216040532.1566229-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAC supports filtering unmatched unicast packets according to
the MAC address table. This patch adds the support for
unicast frame filtering.
To support automatic restoration of MAC entries
after reset, the driver saves a copy of MAC entries in the driver.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20241216040532.1566229-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch initializes debugfs and creates root directory
for each device. The tx_ring and rx_ring debugfs files
are implemented together.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241216040532.1566229-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enhance error handling in Wake-on-LAN (WoL) operations:
- Log a warning in `lan78xx_get_wol` if `lan78xx_read_reg` fails.
- Check and handle errors from `device_set_wakeup_enable` and
`phy_ethtool_set_wol` in `lan78xx_set_wol`.
- Ensure proper cleanup with a unified error handling path.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241216120941.1690908-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove PHY register handling from `lan78xx_get_regs` and
`lan78xx_get_regs_len`. Since the controller can have different PHYs
attached, the first 32 registers are not universally relevant or the
most interesting. Simplify the implementation to focus on MAC and device
registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241216120941.1690908-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename `phy_mutex` to `mdiobus_mutex` for clarity, as the mutex protects
MDIO bus access rather than PHY-specific operations. Update all
references to ensure consistency.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241216120941.1690908-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the generic `done` label to the action-specific `exit_unlock`
label in `lan78xx_mac_reset`. This improves clarity by indicating the
specific cleanup action (mutex unlock) and aligns with best practices
for error handling and cleanup labels.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Link: https://patch.msgid.link/20241216120941.1690908-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update lan78xx_stop_hw to return -ETIMEDOUT instead of -ETIME when
a timeout occurs. While -ETIME indicates a general timer expiration,
-ETIMEDOUT is more commonly used for signaling operation timeouts and
provides better consistency with standard error handling in the driver.
The -ETIME checks in tx_complete() and rx_complete() are unrelated to
this error handling change. In these functions, the error values are derived
from urb->status, which reflects USB transfer errors. The error value from
lan78xx_stop_hw will be exposed in the following cases:
- usb_driver::suspend
- net_device_ops::ndo_stop (potentially, though currently the return value
is not used).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Link: https://patch.msgid.link/20241216120941.1690908-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update `lan78xx_get_regs` to handle errors during register and PHY
reads. Log warnings for failed reads and exit the function early if an
error occurs. Drop all previously logged registers to signal
inconsistent readings to the user space. This ensures that invalid data
is not returned to users.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241216120941.1690908-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are close to removing page->index. Use page->private instead, which
is least likely to be removed.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://patch.msgid.link/20241216155124.3114-1-willy@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Benefit from the recent conversion of the driver to NAPI and enable GRO
support through the use of napi_gro_receive(). Pass the NAPI pointer
from the bus driver (mlxsw_pci) to the switch driver (mlxsw_spectrum)
through the skb control block where various packet metadata is already
encoded.
The main motivation is to improve forwarding performance through the use
of GRO fraglist [1]. In my testing, when the forwarding data path is
simple (routing between two ports) there is not much difference in
forwarding performance between GRO disabled and GRO enabled with
fraglist.
The improvement becomes more noticeable as the data path becomes more
complex since it is traversed less times with GRO enabled. For example,
with 10 ingress and 10 egress flower filters with different priorities
on the two ports between which routing is performed, there is an
improvement of about 140% in forwarded bandwidth.
[1] https://lore.kernel.org/netdev/20200125102645.4782-1-steffen.klassert@secunet.com/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/21258fe55f608ccf1ee2783a5a4534220af28903.1734354812.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241216-sysfs-const-bin_attr-net-v1-4-ec460b91f274@weissschuh.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241216-sysfs-const-bin_attr-net-v1-2-ec460b91f274@weissschuh.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nsim_pp_hold_write() has two problems:
1) It may return with rtnl held, as found by syzbot.
2) Its return value does not propagate an error if any.
Fixes: 1580cbcbfe ("net: netdevsim: add some fake page pool use")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241216083703.1859921-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a race condition between exiting wb_on_itr and completion write
backs. For example, we are in wb_on_itr mode and a Tx completion is
generated by HW, ready to be written back, as we are re-enabling
interrupts:
HW SW
| |
| | idpf_tx_splitq_clean_all
| | napi_complete_done
| |
| tx_completion_wb | idpf_vport_intr_update_itr_ena_irq
That tx_completion_wb happens before the vector is fully re-enabled.
Continuing with this example, it is a UDP stream and the
tx_completion_wb is the last one in the flow (there are no rx packets).
Because the HW generated the completion before the interrupt is fully
enabled, the HW will not fire the interrupt once the timer expires and
the write back will not happen. NAPI poll won't be called. We have
indicated we're back in interrupt mode but nothing else will trigger the
interrupt. Therefore, the completion goes unprocessed, triggering a Tx
timeout.
To mitigate this, fire a SW triggered interrupt upon exiting wb_on_itr.
This interrupt will catch the rogue completion and avoid the timeout.
Add logic to set the appropriate bits in the vector's dyn_ctl register.
Fixes: 9c4a27da0e ("idpf: enable WB_ON_ITR")
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
SW triggered interrupts are guaranteed to fire after their timer
expires, unlike Tx and Rx interrupts which will only fire after the
timer expires _and_ a descriptor write back is available to be processed
by the driver.
Add the necessary fields, defines, and initializations to enable a SW
triggered interrupt in the vector's dyn_ctl register.
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a devlink health reporter for MDD events. The 'dump' handler will
return the information captured in each call to ice_handle_mdd_event().
A device reset (CORER/PFR) will put the reporter back in healthy state.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Co-developed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add Tx hang devlink health reporter, see struct ice_tx_hang_event to see
what exactly is reported. For now dump descriptors with little metadata
and skb diagnostic information.
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Co-developed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Drop "devlink_" prefix from files that sit in devlink/.
I'm going to add more files there, and repeating "devlink" does not feel
good. This is also the scheme used in most other places, most notably the
devlink core files are named like that.
devlink.[ch] stays as is.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Coverity reports an uninit pointer read in qed_mcp_nvm_info_populate().
If EOPNOTSUPP is returned from qed_mcp_bist_nvm_get_num_images() ensure
nvm_info.num_images is set to 0 to avoid possible uninit assignment
to p_hwfn->nvm_info.image_att later on in out label.
Closes: https://scan5.scan.coverity.com/#/project-view/63204/10063?selectedIssue=1636666
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Gianfranco Trad <gianf.trad@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241215011733.351325-2-gianf.trad@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The OF node obtained by of_parse_phandle() is not freed. Call
of_node_put() to balance the refcount.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 1676aba5ef ("net: ethernet: bgmac: device tree phy enablement")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241214014912.2810315-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are two skb pointers to manage tx skb's enqueued from n/w stack.
waiting_tx_skb pointer points to the tx skb which needs to be processed
and ongoing_tx_skb pointer points to the tx skb which is being processed.
SPI thread prepares the tx data chunks from the tx skb pointed by the
ongoing_tx_skb pointer. When the tx skb pointed by the ongoing_tx_skb is
processed, the tx skb pointed by the waiting_tx_skb is assigned to
ongoing_tx_skb and the waiting_tx_skb pointer is assigned with NULL.
Whenever there is a new tx skb from n/w stack, it will be assigned to
waiting_tx_skb pointer if it is NULL. Enqueuing and processing of a tx skb
handled in two different threads.
Consider a scenario where the SPI thread processed an ongoing_tx_skb and
it moves next tx skb from waiting_tx_skb pointer to ongoing_tx_skb pointer
without doing any NULL check. At this time, if the waiting_tx_skb pointer
is NULL then ongoing_tx_skb pointer is also assigned with NULL. After
that, if a new tx skb is assigned to waiting_tx_skb pointer by the n/w
stack and there is a chance to overwrite the tx skb pointer with NULL in
the SPI thread. Finally one of the tx skb will be left as unhandled,
resulting packet missing and memory leak.
- Consider the below scenario where the TXC reported from the previous
transfer is 10 and ongoing_tx_skb holds an tx ethernet frame which can be
transported in 20 TXCs and waiting_tx_skb is still NULL.
tx_credits = 10; /* 21 are filled in the previous transfer */
ongoing_tx_skb = 20;
waiting_tx_skb = NULL; /* Still NULL */
- So, (tc6->ongoing_tx_skb || tc6->waiting_tx_skb) becomes true.
- After oa_tc6_prepare_spi_tx_buf_for_tx_skbs()
ongoing_tx_skb = 10;
waiting_tx_skb = NULL; /* Still NULL */
- Perform SPI transfer.
- Process SPI rx buffer to get the TXC from footers.
- Now let's assume previously filled 21 TXCs are freed so we are good to
transport the next remaining 10 tx chunks from ongoing_tx_skb.
tx_credits = 21;
ongoing_tx_skb = 10;
waiting_tx_skb = NULL;
- So, (tc6->ongoing_tx_skb || tc6->waiting_tx_skb) becomes true again.
- In the oa_tc6_prepare_spi_tx_buf_for_tx_skbs()
ongoing_tx_skb = NULL;
waiting_tx_skb = NULL;
- Now the below bad case might happen,
Thread1 (oa_tc6_start_xmit) Thread2 (oa_tc6_spi_thread_handler)
--------------------------- -----------------------------------
- if waiting_tx_skb is NULL
- if ongoing_tx_skb is NULL
- ongoing_tx_skb = waiting_tx_skb
- waiting_tx_skb = skb
- waiting_tx_skb = NULL
...
- ongoing_tx_skb = NULL
- if waiting_tx_skb is NULL
- waiting_tx_skb = skb
To overcome the above issue, protect the moving of tx skb reference from
waiting_tx_skb pointer to ongoing_tx_skb pointer and assigning new tx skb
to waiting_tx_skb pointer, so that the other thread can't access the
waiting_tx_skb pointer until the current thread completes moving the tx
skb reference safely.
Fixes: 53fbde8ab2 ("net: ethernet: oa_tc6: implement transmit path to transfer tx ethernet frames")
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SPI thread wakes up to perform SPI transfer whenever there is an TX skb
from n/w stack or interrupt from MAC-PHY. Ethernet frame from TX skb is
transferred based on the availability tx credits in the MAC-PHY which is
reported from the previous SPI transfer. Sometimes there is a possibility
that TX skb is available to transmit but there is no tx credits from
MAC-PHY. In this case, there will not be any SPI transfer but the thread
will be running in an endless loop until tx credits available again.
So checking the availability of tx credits along with TX skb will prevent
the above infinite loop. When the tx credits available again that will be
notified through interrupt which will trigger the SPI transfer to get the
available tx credits.
Fixes: 53fbde8ab2 ("net: ethernet: oa_tc6: implement transmit path to transfer tx ethernet frames")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for RTL8125D rev.b. Its XID is 0x689. It is basically
based on the one with XID 0x688, but with different firmware file.
Signed-off-by: ChunHao Lin <hau@realtek.com>
[hkallweit1@gmail.com: rebased after adjusted version numbering]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/75e5e9ec-d01f-43ac-b0f4-e7456baf18d1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adjust version numbering for RTL8126, so that it doesn't overlap with
new RTL8125 versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/6a354364-20e9-48ad-a198-468264288757@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a check for NULL at the start of create_txqs() and
create_rxqs() which tess if "nic_dev->txqs" is non-NULL. The
intention is that if the device is already open and the queues
are already created then we don't create them a second time.
However, the bug is that if we have an error in the create_txqs()
then the pointer doesn't get set back to NULL. The NULL check
at the start of the function will say that it's already open when
it's not and the device can't be used.
Set ->txqs back to NULL on cleanup on error.
Fixes: c3e79baf1b ("net-next/hinic: Add logical Txq and Rxq")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0cc98faf-a0ed-4565-a55b-0fa2734bc205@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small follow-up to align this to an equivalent behavior as the bond driver.
The change in 3625920b62 ("teaming: fix vlan_features computing") removed
the netdevice vlan_features when there is no team port attached, yet it
leaves the full set of enc_features intact.
Instead, leave the default features as pre 3625920b62, and recompute once
we do have ports attached. Also, similarly as in bonding case, call the
netdev_base_features() helper on the enc_features.
Fixes: 3625920b62 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241213123657.401868-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "gl->tot_len" variable is controlled by the user. It comes from
process_responses(). On 32bit systems, the "gl->tot_len +
sizeof(struct cpl_pass_accept_req) + sizeof(struct rss_header)" addition
could have an integer wrapping bug. Use size_add() to prevent this.
Fixes: a089439478 ("crypto: chtls - Register chtls with net tls")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/c6bfb23c-2db2-4e1b-b8ab-ba3925c82ef5@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
mlx5-next 2024-12-16
The following pull-request contains mlx5 IFC updates.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Add device cap abs_native_port_num
net/mlx5: qos: Add ifc support for cross-esw scheduling
net/mlx5: Add support for new scheduling elements
net/mlx5: Add ConnectX-8 device to ifc
net/mlx5: ifc: Reorganize mlx5_ifc_flow_table_context_bits
====================
Link: https://patch.msgid.link/20241216124028.973763-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now everything in ath12k is in place and we can enable Multi-Link Operation
(MLO) in the driver. For now it's only enabled for QCN9274 with firmware having
ATH12K_FW_FEATURE_MLO feature bit set.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the QMI host capability, the device index, the number of local
links, and the corresponding hardware link IDs are sent. The hardware link ID
assignment is based on the local variable `hw_link_id`, which starts from 0 and
ranges up to `num_local_links` in the device. Starting from 0 is not ideal
because it can result in the same link ID being assigned to different devices
in certain scenarios (e.g., split MAC). Additionally, for multi link
operations the firmware expects the hardware link IDs in the same order as the
Wireless Serial Interface (WSI) connection.
Hence, for MLO to function seamlessly, the hardware link IDs across devices
need to be unique and should follow the order of the WSI connection. To address
this, a previous change read the WSI index from the Device Tree (DT) and stored
it. Use this WSI index to determine the starting hardware link IDs for each
device, ensuring uniqueness and correct order across all devices.
While at it, add debug prints to clearly show the MLO capability advertisement
sent during QMI host capability exchange.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
To maintain backward compatibility with older firmware versions, introduce a
new feature bit, ATH12K_FW_FEATURE_MLO, to identify whether the firmware
supports MLO. If the firmware-X.bin does not have this bit advertised in the
feature, then MLO capability in the host will be disabled.
This applies only for QCN9274 chipsets.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the function ath12k_htt_mlo_offset_event_handler(), it is possible that
the ar is not yet active (started). The function
ath12k_mac_get_ar_by_pdev_id() only searches for active pdev, so a NULL
return is possible. Therefore, there is no need to print a warning,
instead, just silently discard the message.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, certain WMI events are frequently received by the host. Since
the host lacks the logic to process these events, the console is flooded
with ‘Unknown eventid:’ debug messages.
To address this, handle these events gracefully without printing debug
messages. There is already a block of event IDs that are ignored with a debug
print. However, this new type of event occurs more frequently, so no debug
print is necessary, and handling it should be a no-op.
While at it, re-arrange the code so that all Unknown event IDs are towards
the end of the switch block.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When operating as an ML station, mac80211 initially activates only one link in
the driver until the peer is authorized. Once the state changes to authorized,
the driver should call mac80211 API to activate all other partner links.
Before doing so, mac80211 checks if the driver supports activating links via
the can_activate_links mac80211_ops. Therefore, add support for this
mac80211_ops and call the API to activate the links once the state changes to
authorized.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the hardware scan is initiated in the driver on scan link (15).
After mapping to the appropriate radio based on the scan frequency, the vdev is
created and the scan begins. However, the vdev is only deleted when channel
assignment is about to occur after the scan. Additionally, it is also deleted
if a new scan is requested on the same interface but the underlying radio
differs in the new request.
This imbalance leads to various hardware scan issues, especially when a non-MLO
and MLO combination exists. In such cases, the latter tries to skip the scan
and proceed with channel assignment while the former is still scanning, causing
a firmware assert.
To address this issue, symmetrize the scan vdev creation and deletion during
hardware scan operations. This means creating a vdev when the scan starts and
deleting it once the scan is completed or aborted.
While at this, add a few debug prints in scan handling and a few empty lines
for better code read.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
mac80211 expects link_id in some scenarios or else the packet might
get dropped. Hence, add link_id information before delivering the skb.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-10-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the ath12k_mac_hw_register() function's context, ar is an iterator
variable, and there is no assurance that the last ar will be the one with
6 GHz enabled. Therefore, checking directly ar->supports_6ghz outside the
loop is not appropriate.
Additionally, 6 GHz lacks HT capabilities. To obtain the super set of
HT capabilities across all grouped radios, 6 GHz should be excluded.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-9-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If the requested memory chunk is too large, an error message is logged, but the
request continues to be processed. However, no actual memory is allocated to
the firmware from this request. Instead, the firmware sends another request
with smaller chunks, where memory will be allocated accordingly. Therefore, it
is pointless to proceed with parsing the request if at least one of the
requests cannot be fulfilled.
Hence, return -EAGAIN immediately and proceed to process the new request.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The prerequisite for MLO support in cfg80211/mac80211 requires that all the
links participating in MLO belong to the same wiphy/struct ieee80211_hw. The
driver needs to group multiple discrete hardware components, each acting as a
link in MLO, under one wiphy. Consequently, the driver advertises
multi-hardware device interface combination capabilities specific to the radio,
including supported frequencies. The global interface combination represent the
combined interface capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, radio stores the low frequency and high frequency information as
separate variables. However, cfg80211 already provides a suitable data
structure struct wiphy_radio_freq_range to store this information efficiently.
Additionally, for multi radio per wiphy infrastructure, this frequency range
information is essential. In future patches using struct wiphy_radio_freq_range
makes the code simpler.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce a cleanup helper function to avoid redundant code for interface
combination cleanup. Remove the cleanup code from ath12k_mac_hw_unregister()
and ath12k_mac_hw_register() and replace it with a new cleanup helper function.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the Inter Multi-Link Operation, the primary device is expected to receive
the partner device buffer. Therefore, each device initializes the partner
device buffer in their cmem configuration. So add a helper function to
initialize the partner device buffer in their cmem configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, partner device buffer is not handled in the receive data path. In
Multi-Link Operation, the partner device buffer is reported to the primary
upper MAC rings. Therefore, add partner device buffer processing in the REO and
Exception ring handler.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, all the rx processing treats the hardware link id as the MAC id.
The HW link id is a unique identifier for all hardware links participating in
the multi link group. Therefore, the current MAC id derivation is insufficient
to process the partner rx buffer in the Multi-Link Operation. So derive the
MAC id from the HW link id and implementing this change in rx processing will
enable the scaling of partner buffer processing in Multi-Link Operation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in DP rx error processing, the MAC id is fetched redundantly from
the same descriptor for each MSDU. To avoid this redundancy, move the fetch
handling before the iteration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-9-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of multi device group abstraction, host has to exchange the multi-link
operation commands such as setup and ready to firmware before registering the
device group to mac80211.
The multi-link operation commands - setup, ready and teardown are necessary for
many commands such as WMI_PEER_ASSOC_CMD, WMI_BCN_TMPL_CMD in case of
multi-link interfaces.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of multi device group abstraction, host has to exchange the MLO
commands such as setup, teardown and ready to firmware.
Once multi device group is ready, host has to exchange MLO setup command with
partner devices link information and followed by MLO ready command to firmware.
During deinit, MLO teardown command should be sent to firmware. Firmware would
send MLO setup complete and MLO teardown complete to host for MLO setup command
and MLO teardown command respectively.
Added WMI helper functions for the MLO setup, ready and teardown command
and the handling for corresponding event from firmware. Add appropriate WMI
tag, command id and event id to parse the event and send request.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
To enable Multi-Link Operation (MLO), QCN9274 firmware requests MLO global
memory (MLO_GLOBAL_MEM_REGION_TYPE). This memory region is shared across all
the firmware (SoC) that are participation in the MLO.
Hence, add support to allocate and free MLO global memory region. Allocate one
MLO global memory per struct ath12k_hw_group and assign the same memory to all
firmware in the same struct ath12k_hw_group. WCN7850 firmware does not request
this memory type, therefore this change will have no impact on WCN7850 device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, all QMI target memory types share the same allocation logic within
ath12k_qmi_alloc_target_mem_chunk(). However, for Multi-Link Operation (MLO),
the firmware requests a new MLO global memory region. This memory is shared
across different firmware (SoC) participating in the MLO. To accommodate this
logic change, refactor ath12k_qmi_alloc_target_mem_chunk() and introduce a
helper function ath12k_qmi_alloc_chunk() for memory chunk allocation.
Subsequent patch will add MLO global memory allocation logic.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, QMI MLO host capability is sent with the details of local links and
hw_link id only for particular device. But in the case of multi device group
abstraction, it has to include the details of hw_link_id, num_local_links of
every partner device that is involved in the group during QMI MLO capability
exchange. Add changes to send partner device details to the firmware in QMI MLO
capability exchange.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, a single device is part of the device group abstraction. However,
for multi-link operations, multiple devices need to be combined. This
multi-device grouping is done via WSI (WLAN Serial Interface), which is
described in the Device Tree. Information about different WSI groups and the
number of devices involved in each group can be parsed from the Device Tree.
Add changes to parse the Device Tree and determine WSI information, such as the
different WSI groups and the number of devices per WSI group. Assign WSI index
zero to the WSI controller device (to synchronize the clock among the devices
within the WSI group), and increment the WSI index of each device in the order
of the WSI connection.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce the description of a hwtstamp provider, mainly defined with a
the hwtstamp source and the phydev pointer.
Add a hwtstamp provider description within the netdev structure to
allow saving the hwtstamp we want to use. This prepares for future
support of an ethtool netlink command to select the desired hwtstamp
provider. By default, the old API that does not support hwtstamp
selectability is used, meaning the hwtstamp provider pointer is unset.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing linked list based implementation of how ts tags are
assigned and managed is unsafe against concurrency and corner cases:
- element addition in tx processing can race against element removal
in ts queue completion,
- element removal in ts queue completion can race against element
removal in device close,
- if a large number of frames gets added to tx queue without ts queue
completions in between, elements with duplicate tag values can get
added.
Use a different implementation, based on per-port used tags bitmaps and
saved skb arrays.
Safety for addition in tx processing vs removal in ts completion is
provided by:
tag = find_first_zero_bit(...);
smp_mb();
<write rdev->ts_skb[tag]>
set_bit(...);
vs
<read rdev->ts_skb[tag]>
smp_mb();
clear_bit(...);
Safety for removal in ts completion vs removal in device close is
provided by using atomic read-and-clear for rdev->ts_skb[tag]:
ts_skb = xchg(&rdev->ts_skb[tag], NULL);
if (ts_skb)
<handle it>
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://patch.msgid.link/20241212062558.436455-1-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some calls into ionic_get_module_eeprom() don't use a single
full buffer size, but instead multiple calls with an offset.
Teach our driver to use the offset correctly so we can
respond appropriately to the caller.
Fixes: 4d03e00a21 ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241212213157.12212-4-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are some FW error handling paths that can cause us to
try to destroy the workqueue more than once, so let's be sure
we're checking for that.
The case where this popped up was in an AER event where the
handlers got called in such a way that ionic_reset_prepare()
and thus ionic_dev_teardown() got called twice in a row.
The second time through the workqueue was already destroyed,
and destroy_workqueue() choked on the bad wq pointer.
We didn't hit this in AER handler testing before because at
that time we weren't using a private workqueue. Later we
replaced the use of the system workqueue with our own private
workqueue but hadn't rerun the AER handler testing since then.
Fixes: 9e25450da7 ("ionic: add private workqueue per-device")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241212213157.12212-3-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If register_netdev() fails, then the driver leaks the netdev notifier.
Fix this by calling ionic_lif_unregister() on register_netdev()
failure. This will also call ionic_lif_unregister_phc() if it has
already been registered.
Fixes: 30b87ab4c0 ("ionic: remove lif list concept")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241212213157.12212-2-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplify framer_provider_simple_of_xlate() implementation by API
class_find_device_by_of_node().
Also correct comments to mark its parameter @dev as unused instead of
@args in passing.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241213-net_fix-v2-1-6d06130d630f@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit b35108a51c ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
@@ constant C; @@
- msecs_to_jiffies(C * 1000)
+ secs_to_jiffies(C)
@@ constant C; @@
- msecs_to_jiffies(C * MSEC_PER_SEC)
+ secs_to_jiffies(C)
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Link: https://patch.msgid.link/20241212-netdev-converge-secs-to-jiffies-v4-1-6dac97a6d6ab@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When DCB is disabled, the pfc_en struct member cannot be accessed:
drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.c: In function 'otx2_is_pfc_enabled':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.c:22:48: error: 'struct otx2_nic' has no member named 'pfc_en'
22 | return IS_ENABLED(CONFIG_DCB) && !!pfvf->pfc_en;
| ^~
drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.c: In function 'otx2_nix_config_bp':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.c:1755:33: error: 'IEEE_8021QAZ_MAX_TCS' undeclared (first use in this function)
1755 | req->chan_cnt = IEEE_8021QAZ_MAX_TCS;
| ^~~~~~~~~~~~~~~~~~~~
Move the member out of the #ifdef block to avoid putting back another
check in the source file and add the missing include file unconditionally.
Fixes: a7ef63dbd5 ("octeontx2-af: Disable backpressure between CPT and NIX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241213083228.2645757-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit aa58bec064 ("net: ethernet: oa_tc6: implement register
write operation") introduced a library that implements the OPEN Alliance
TC6 10BASE-T1x MAC-PHY Serial Interface protocol for supporting
10BASE-T1x MAC-PHYs.
There is no need to ask the user about enabling this library, as all
drivers that use it select the OA_TC6 symbol. Hence make the symbol
invisible, unless when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/3b600550745af10ab7d7c3526353931c1d39f641.1733994552.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems that phylink does not support driving PHYs in SFP modules using
the Generic PHY or Generic Clause 45 PHY driver. I've come to this
conclusion after analyzing these facts:
- sfp_sm_probe_phy(), who is our caller here, first calls
phy_device_register() and then sfp_add_phy() -> ... ->
phylink_sfp_connect_phy().
- phydev->supported is populated by phy_probe()
- phy_probe() is usually called synchronously from phy_device_register()
via phy_bus_match(), if a precise device driver is found for the PHY.
In that case, phydev->supported has a good chance of being set to a
non-zero mask.
- There is an exceptional case for the PHYs for which phy_bus_match()
didn't find a driver. Those devices sit for a while without a driver,
then phy_attach_direct() force-binds the genphy_c45_driver or
genphy_driver to them. Again, this triggers phy_probe() and renders
a good chance of phydev->supported being populated, assuming
compatibility with genphy_read_abilities() or
genphy_c45_pma_read_abilities().
- phylink_sfp_config_phy() does not support the exceptional case of
retrieving phydev->supported from the Generic PHY driver, due to its
code flow. It expects the phydev->supported mask to already be
non-empty, because it first calls phylink_validate() on it, and only
calls phylink_attach_phy() if that succeeds. Thus, phylink_attach_phy()
-> phy_attach_direct() has no chance of running.
It is not my wish to change the state of affairs by altering the code
flow, but merely to document the limitation rather than have the current
unspecific error:
[ 61.800079] mv88e6085 d0032004.mdio-mii:12 sfp: validation with support 00,00000000,00000000,00000000 failed: -EINVAL
[ 61.820743] sfp sfp: sfp_add_phy failed: -EINVAL
On the premise that an empty phydev->supported is going to make
phylink_validate() fail anyway, and that this is caused by a missing PHY
driver, it would be more informative to single out that case, undercut
the entire phylink_sfp_config_phy() call, including phylink_validate(),
and print a more specific message for this common gotcha:
[ 37.076403] mv88e6085 d0032004.mdio-mii:12 sfp: PHY i2c:sfp:16 (id 0x01410cc2) has no driver loaded
[ 37.089157] mv88e6085 d0032004.mdio-mii:12 sfp: Drivers which handle known common cases: CONFIG_BCM84881_PHY, CONFIG_MARVELL_PHY
[ 37.108047] sfp sfp: sfp_add_phy failed: -EINVAL
Link: https://lore.kernel.org/netdev/20241113144229.3ff4bgsalvj7spb7@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20241212140834.278894-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packets injected by the CPU should have a SRC_PORT field equal to the
CPU port module index in the Analyzer block (ocelot->num_phys_ports).
The blamed commit copied the ocelot_ifh_set_basic() call incorrectly
from ocelot_xmit_common() in net/dsa/tag_ocelot.c. Instead of calling
with "x", it calls with BIT_ULL(x), but the field is not a port mask,
but rather a single port index.
[ side note: this is the technical debt of code duplication :( ]
The error used to be silent and doesn't appear to have other
user-visible manifestations, but with new changes in the packing
library, it now fails loudly as follows:
------------[ cut here ]------------
Cannot store 0x40 inside bits 46-43 - will truncate
sja1105 spi2.0: xmit timed out
WARNING: CPU: 1 PID: 102 at lib/packing.c:98 __pack+0x90/0x198
sja1105 spi2.0: timed out polling for tstamp
CPU: 1 UID: 0 PID: 102 Comm: felix_xmit
Tainted: G W N 6.13.0-rc1-00372-gf706b85d972d-dirty #2605
Call trace:
__pack+0x90/0x198 (P)
__pack+0x90/0x198 (L)
packing+0x78/0x98
ocelot_ifh_set_basic+0x260/0x368
ocelot_port_inject_frame+0xa8/0x250
felix_port_deferred_xmit+0x14c/0x258
kthread_worker_fn+0x134/0x350
kthread+0x114/0x138
The code path pertains to the ocelot switchdev driver and to the felix
secondary DSA tag protocol, ocelot-8021q. Here seen with ocelot-8021q.
The messenger (packing) is not really to blame, so fix the original
commit instead.
Fixes: e1b9e80236 ("net: mscc: ocelot: fix QoS class for injected packets with "ocelot-8021q"")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241212165546.879567-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The GPIO2 pin on the DP83822 can be configured as clock output. Add support
for configuration via DT.
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_intx() is a hybrid function which can sometimes be managed through
devres. To remove this hybrid nature from pci_intx(), it is necessary to
port users to either an always-managed or a never-managed version.
qtnfmac enables its PCI device with pcim_enable_device(). Thus, it needs
the always-managed version.
Replace pci_intx() with pcim_intx().
Link: https://lore.kernel.org/r/20241209130632.132074-11-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
dwmac510_tc_ops and dwxgmac_tc_ops are completely identical,
keep dwmac510_tc_ops to provide better backward compatibility.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Link: https://patch.msgid.link/20241212033325.282817-1-0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Regular development in this period. Main changes are listed:
rtl8xxxu:
* add more USB devices IDs
rtlwifi:
* refine error path
rtw88:
* add more USB devices IDs
* enable USB RX aggregation and USB 3 to improve performance
rtw89:
* implement more stuffs including PS flow for MLO
-----BEGIN PGP SIGNATURE-----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=Lt77
-----END PGP SIGNATURE-----
Merge tag 'rtw-next-2024-12-12' of https://github.com/pkshih/rtw
rtw-next patches for v6.14
Regular development in this period. Main changes are listed:
rtl8xxxu:
* add more USB devices IDs
rtlwifi:
* refine error path
rtw88:
* add more USB devices IDs
* enable USB RX aggregation and USB 3 to improve performance
rtw89:
* implement more stuffs including PS flow for MLO
Including the fwil.h header file can lead to a build error:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h: \
In function ‘brcmf_fil_cmd_int_set’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h:90:9: error: implicit \
declaration of function ‘brcmf_dbg’ [-Werror=implicit-function-declaration]
90 | brcmf_dbg(FIL, "ifidx=%d, cmd=%d, value=%d\n", ifp->ifidx, cmd, data);
| ^~~~~~~~~
The error is often avoided because the debug.h header file is included
before the fwil.h header file.
This makes sure the header include order is irrelevant by explicitly adding the
debug.h header.
Fixes: 31343230ab ("wifi: brcmfmac: export firmware interface functions")
Signed-off-by: Marcel Hamer <marcel.hamer@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241211133618.2014083-1-marcel.hamer@windriver.com
In 'wlc_phy_iqcal_gainparams_nphy()', add gain range check to WARN()
instead of possible out-of-bounds 'tbl_iqcal_gainparams_nphy' access.
Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241210070441.836362-1-dmantipov@yandex.ru
When removing a netfront device directly after a suspend/resume cycle
it might happen that the queues have not been setup again, causing a
crash during the attempt to stop the queues another time.
Fix that by checking the queues are existing before trying to stop
them.
This is XSA-465 / CVE-2024-53240.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: d50b7914fa ("xen-netfront: Fix NULL sring after live migration")
Signed-off-by: Juergen Gross <jgross@suse.com>
Initially, xdp_frame::mem.id was used to search for the corresponding
&page_pool to return the page correctly.
However, after that struct page was extended to have a direct pointer
to its PP (netmem has it as well), further keeping of this field makes
no sense. xdp_return_frame_bulk() still used it to do a lookup, and
this leftover is now removed.
Remove xdp_frame::mem and replace it with ::mem_type, as only memory
type still matters and we need to know it to be able to free the frame
correctly.
As a cute side effect, we can now make every scalar field in &xdp_frame
of 4 byte width, speeding up accesses to them.
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20241211172649.761483-3-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ath12k_mac_assign_vif_to_vdev(), if arvif is created on a different
radio, it gets deleted from that radio through a call to
ath12k_mac_unassign_link_vif(). This action frees the arvif pointer.
Subsequently, there is a check involving arvif, which will result in a
read-after-free scenario.
Fix this by moving this check after arvif is again assigned via call to
ath12k_mac_assign_link_vif().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Closes: https://scan5.scan.coverity.com/#/project-view/63541/10063?selectedIssue=1636423
Fixes: b5068bc918 ("wifi: ath12k: Cache vdev configs before vdev create")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241210-read_after_free-v1-1-969f69c7d66c@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit 8d7ae22ae9 ("net: dsa: microchip: KSZ9477 register regmap
alignment to 32 bit boundaries") fixed an issue whereby regmap_reg_range
did not allow writes as 32 bit words to KSZ9477 PHY registers, this fix
for KSZ9896 is adapted from there as the same errata is present in
KSZ9896C as "Module 5: Certain PHY registers must be written as pairs
instead of singly" the explanation below is likewise taken from this
commit.
The commit provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accessed as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9896 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Fixes: 5c844d57aa ("net: dsa: microchip: fix writes to phy registers >= 0x10")
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Link: https://patch.msgid.link/20241211092932.26881-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MPIC.PIS must be set per phy interface type.
MPIC.LSC must be set per speed.
Do that strictly per datasheet, instead of hardcoding MPIC.PIS to GMII.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241211053012.368914-1-nikita.yoush@cogentembedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Teach the driver to recognize and decode the sfp pid
SFF8024_ID_QSFP_PLUS_CMIS correctly.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add higher speed defines to the ionic_if.h API and decode them
in the ethtool get_link_ksettings callback.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of reporting -EINVAL when IONIC_RC_ENOSUPP is returned use
the -EOPNOTSUPP value. This aligns better since the FW only returns
IONIC_RC_ENOSUPP when operations aren't supported not when invalid
values are used.
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace when ETH_HLEN and VLAN_HLEN are used together with
VLAN_ETH_HLEN since it's the same value and uses 1 define
instead of 2.
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that the firmware has learned how to properly report
the asic type id, add the values to our interface file.
The sharp-eyed reviewers will catch that the CAPRI value
changed here from 0 to 1. This comes with the FW actually
defining it correctly. This is safe for us to change as
nothing actually uses that value yet.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Similar to bonding driver, add NETIF_F_GSO_ENCAP_ALL to TEAM_VLAN_FEATURES
in order to support slave devices which propagate NETIF_F_GSO_UDP_TUNNEL &
NETIF_F_GSO_UDP_TUNNEL_CSUM as vlan_features.
Fixes: 3625920b62 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-5-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Similarly as with bonding, fix the calculation of vlan_features to reuse
netdev_base_features() in order derive the set in the same way as
ndo_fix_features before iterating through the slave devices to refine the
feature set.
Fixes: 3625920b62 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-4-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers like mlx5 expose NIC's vlan_features such as
NETIF_F_GSO_UDP_TUNNEL & NETIF_F_GSO_UDP_TUNNEL_CSUM which are
later not propagated when the underlying devices are bonded and
a vlan device created on top of the bond.
Right now, the more cumbersome workaround for this is to create
the vlan on top of the mlx5 and then enslave the vlan devices
to a bond.
To fix this, add NETIF_F_GSO_ENCAP_ALL to BOND_VLAN_FEATURES
such that bond_compute_features() can probe and propagate the
vlan_features from the slave devices up to the vlan device.
Given the following bond:
# ethtool -i enp2s0f{0,1}np{0,1}
driver: mlx5_core
[...]
# ethtool -k enp2s0f0np0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k enp2s0f1np1 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k bond0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Before:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: off [requested on]
tx-udp_tnl-csum-segmentation: off [requested on]
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
After:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Various users have run into this reporting performance issues when
configuring Cilium in vxlan tunneling mode and having the combination
of bond & vlan for the core devices connecting the Kubernetes cluster
to the outside world.
Fixes: a9b3ace44c ("bonding: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-3-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If a bonding device has slave devices, then the current logic to derive
the feature set for the master bond device is limited in that flags which
are fully supported by the underlying slave devices cannot be propagated
up to vlan devices which sit on top of bond devices. Instead, these get
blindly masked out via current NETIF_F_ALL_FOR_ALL logic.
vlan_features and mpls_features should reuse netdev_base_features() in
order derive the set in the same way as ndo_fix_features before iterating
through the slave devices to refine the feature set.
Fixes: a9b3ace44c ("bonding: fix vlan_features computing")
Fixes: 2e770b507c ("net: bonding: Inherit MPLS features from slave devices")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-2-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Both bonding and team driver have logic to derive the base feature
flags before iterating over their slave devices to refine the set
via netdev_increment_features().
Add a small helper netdev_base_features() so this can be reused
instead of having it open-coded multiple times.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241210141245.327886-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement the .support_eee() method by reusing the ksz_validate_eee()
method as a template, renaming the function, changing the return type
and values, and removing it from the ksz_set_mac_eee() and
ksz_get_mac_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14Z-006cZs-6o@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14U-006cZm-2K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14O-006cZg-VM@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method by using the generic helper as all
user ports support EEE.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14J-006cZa-Rh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .support_eee() method to indicate that EEE is not
supported by two switch variants, rather than making these checks in
the .set_mac_eee() and .get_mac_eee() methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/E1tL14E-006cZU-Nc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
