The 5760X (P7) chip's HW GRO/LRO interface is very similar to that of
the previous generation (5750X or P5). However, the aggregation ID
fields in the completion structures on P7 have been redefined from
16 bits to 12 bits. The freed up 4 bits are redefined for part of the
metadata such as the VLAN ID. The aggregation ID mask was not modified
when adding support for P7 chips. Including the extra 4 bits for the
aggregation ID can potentially cause the driver to store or fetch the
packet header of GRO/LRO packets in the wrong TPA buffer. It may hit
the BUG() condition in __skb_pull() because the SKB contains no valid
packet header:
kernel BUG at include/linux/skbuff.h:2766!
Oops: invalid opcode: 0000 1 PREEMPT SMP NOPTI
CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Kdump: loaded Tainted: G OE 6.12.0-rc2+ #7
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: Dell Inc. PowerEdge R760/0VRV9X, BIOS 1.0.1 12/27/2022
RIP: 0010:eth_type_trans+0xda/0x140
Code: 80 00 00 00 eb c1 8b 47 70 2b 47 74 48 8b 97 d0 00 00 00 83 f8 01 7e 1b 48 85 d2 74 06 66 83 3a ff 74 09 b8 00 04 00 00 eb a5 <0f> 0b b8 00 01 00 00 eb 9c 48 85 ff 74 eb 31 f6 b9 02 00 00 00 48
RSP: 0018:ff615003803fcc28 EFLAGS: 00010283
RAX: 00000000000022d2 RBX: 0000000000000003 RCX: ff2e8c25da334040
RDX: 0000000000000040 RSI: ff2e8c25c1ce8000 RDI: ff2e8c25869f9000
RBP: ff2e8c258c31c000 R08: ff2e8c25da334000 R09: 0000000000000001
R10: ff2e8c25da3342c0 R11: ff2e8c25c1ce89c0 R12: ff2e8c258e0990b0
R13: ff2e8c25bb120000 R14: ff2e8c25c1ce89c0 R15: ff2e8c25869f9000
FS: 0000000000000000(0000) GS:ff2e8c34be300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055f05317e4c8 CR3: 000000108bac6006 CR4: 0000000000773ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x33/0x90
? do_trap+0xd9/0x100
? eth_type_trans+0xda/0x140
? do_error_trap+0x65/0x80
? eth_type_trans+0xda/0x140
? exc_invalid_op+0x4e/0x70
? eth_type_trans+0xda/0x140
? asm_exc_invalid_op+0x16/0x20
? eth_type_trans+0xda/0x140
bnxt_tpa_end+0x10b/0x6b0 [bnxt_en]
? bnxt_tpa_start+0x195/0x320 [bnxt_en]
bnxt_rx_pkt+0x902/0xd90 [bnxt_en]
? __bnxt_tx_int.constprop.0+0x89/0x300 [bnxt_en]
? kmem_cache_free+0x343/0x440
? __bnxt_tx_int.constprop.0+0x24f/0x300 [bnxt_en]
__bnxt_poll_work+0x193/0x370 [bnxt_en]
bnxt_poll_p5+0x9a/0x300 [bnxt_en]
? try_to_wake_up+0x209/0x670
__napi_poll+0x29/0x1b0
Fix it by redefining the aggregation ID mask for P5_PLUS chips to be
12 bits. This will work because the maximum aggregation ID is less
than 4096 on all P5_PLUS chips.
Fixes: 13d2d3d381 ("bnxt_en: Add new P7 hardware interface definitions")
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241209015448.1937766-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The extern declarations should be in a header file that corresponds to
their definition, move these extern declarations to its header file.
Some of them have nowhere to go, so move them to hwif.h since they are
referenced in hwif.c only.
dwmac100_* dwmac1000_* dwmac4_* dwmac410_* dwmac510_* stay in hwif.h,
otherwise you will be flooded with name conflicts from dwmac100.h,
dwmac1000.h and dwmac4.h if hwif.c try to #include these .h files.
Compile tested only.
No functional change intended.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20241208070202.203931-1-0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Different families of switches have different statistics available.
This information is current hard coded into functions, however this
information will also soon be needed when getting statistics from the
RMU. Move it into the info structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241207-v6-13-rc1-net-next-mv88e6xxx-stats-refactor-v1-1-b9960f839846@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
virtnet_sq_bind_xsk_pool() flushes tx skbs and then resets tx queue, so
DQL counters need to be reset when flushing has actually occurred, Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_resize()
to handle this.
Fixes: 21a4e3ce6d ("virtio_net: xsk: bind/unbind xsk for tx")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When virtqueue_reset() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when it really occurs.
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
virtnet_tx_resize() flushes remaining tx skbs, requiring DQL counters to
be reset when flushing has actually occurred. Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_reset() to
handle this.
Fixes: c8bd1f7f3e ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When virtqueue_resize() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when the recycle really occurs.
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While not harmful, using vq2rxq where it's always sq appears odd.
Replace it with the more appropriate vq2txq for clarity and correctness.
Fixes: 89f86675cb ("virtio_net: xsk: tx: support xmit xsk buffer")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When virtnet_close is followed by virtnet_open, some TX completions can
possibly remain unconsumed, until they are finally processed during the
first NAPI poll after the netdev_tx_reset_queue(), resulting in a crash
[1]. Commit b96ed2c97c ("virtio_net: move netdev_tx_reset_queue() call
before RX napi enable") was not sufficient to eliminate all BQL crash
cases for virtio-net.
This issue can be reproduced with the latest net-next master by running:
`while :; do ip l set DEV down; ip l set DEV up; done` under heavy network
TX load from inside the machine.
netdev_tx_reset_queue() can actually be dropped from virtnet_open path;
the device is not stopped in any case. For BQL core part, it's just like
traffic nearly ceases to exist for some period. For stall detector added
to BQL, even if virtnet_close could somehow lead to some TX completions
delayed for long, followed by virtnet_open, we can just take it as stall
as mentioned in commit 6025b9135f ("net: dqs: add NIC stall detector
based on BQL"). Note also that users can still reset stall_max via sysfs.
So, drop netdev_tx_reset_queue() from virtnet_enable_queue_pair(). This
eliminates the BQL crashes. As a result, netdev_tx_reset_queue() is now
explicitly required in freeze/restore path. This patch adds it to
immediately after free_unused_bufs(), following the rule of thumb:
netdev_tx_reset_queue() should follow any SKB freeing not followed by
netdev_tx_completed_queue(). This seems the most consistent and
streamlined approach, and now netdev_tx_reset_queue() runs whenever
free_unused_bufs() is done.
[1]:
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:99!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 7 UID: 0 PID: 1598 Comm: ip Tainted: G N 6.12.0net-next_main+ #2
Tainted: [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), \
BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:dql_completed+0x26b/0x290
Code: b7 c2 49 89 e9 44 89 da 89 c6 4c 89 d7 e8 ed 17 47 00 58 65 ff 0d
4d 27 90 7e 0f 85 fd fe ff ff e8 ea 53 8d ff e9 f3 fe ff ff <0f> 0b 01
d2 44 89 d1 29 d1 ba 00 00 00 00 0f 48 ca e9 28 ff ff ff
RSP: 0018:ffffc900002b0d08 EFLAGS: 00010297
RAX: 0000000000000000 RBX: ffff888102398c80 RCX: 0000000080190009
RDX: 0000000000000000 RSI: 000000000000006a RDI: 0000000000000000
RBP: ffff888102398c00 R08: 0000000000000000 R09: 0000000000000000
R10: 00000000000000ca R11: 0000000000015681 R12: 0000000000000001
R13: ffffc900002b0d68 R14: ffff88811115e000 R15: ffff8881107aca40
FS: 00007f41ded69500(0000) GS:ffff888667dc0000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556ccc2dc1a0 CR3: 0000000104fd8003 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x32/0x80
? do_trap+0xd9/0x100
? dql_completed+0x26b/0x290
? dql_completed+0x26b/0x290
? do_error_trap+0x6d/0xb0
? dql_completed+0x26b/0x290
? exc_invalid_op+0x4c/0x60
? dql_completed+0x26b/0x290
? asm_exc_invalid_op+0x16/0x20
? dql_completed+0x26b/0x290
__free_old_xmit+0xff/0x170 [virtio_net]
free_old_xmit+0x54/0xc0 [virtio_net]
virtnet_poll+0xf4/0xe30 [virtio_net]
? __update_load_avg_cfs_rq+0x264/0x2d0
? update_curr+0x35/0x260
? reweight_entity+0x1be/0x260
__napi_poll.constprop.0+0x28/0x1c0
net_rx_action+0x329/0x420
? enqueue_hrtimer+0x35/0x90
? trace_hardirqs_on+0x1d/0x80
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? sched_clock_cpu+0xd/0x1a0
handle_softirqs+0x138/0x3e0
do_softirq.part.0+0x89/0xc0
</IRQ>
<TASK>
__local_bh_enable_ip+0xa7/0xb0
virtnet_open+0xc8/0x310 [virtio_net]
__dev_open+0xfa/0x1b0
__dev_change_flags+0x1de/0x250
dev_change_flags+0x22/0x60
do_setlink.isra.0+0x2df/0x10b0
? rtnetlink_rcv_msg+0x34f/0x3f0
? netlink_rcv_skb+0x54/0x100
? netlink_unicast+0x23e/0x390
? netlink_sendmsg+0x21e/0x490
? ____sys_sendmsg+0x31b/0x350
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? __nla_validate_parse+0x5f/0xee0
? __pfx___probestub_irq_enable+0x3/0x10
? __create_object+0x5e/0x90
? security_capable+0x3b/0x70
rtnl_newlink+0x784/0xaf0
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? stack_depot_save_flags+0x24/0x6d0
? __pfx_rtnl_newlink+0x10/0x10
rtnetlink_rcv_msg+0x34f/0x3f0
? do_syscall_64+0x6c/0x180
? entry_SYSCALL_64_after_hwframe+0x76/0x7e
? __pfx_rtnetlink_rcv_msg+0x10/0x10
netlink_rcv_skb+0x54/0x100
netlink_unicast+0x23e/0x390
netlink_sendmsg+0x21e/0x490
____sys_sendmsg+0x31b/0x350
? copy_msghdr_from_user+0x6d/0xa0
___sys_sendmsg+0x86/0xd0
? __pte_offset_map+0x17/0x160
? preempt_count_add+0x69/0xa0
? __call_rcu_common.constprop.0+0x147/0x610
? preempt_count_add+0x69/0xa0
? preempt_count_add+0x69/0xa0
? _raw_spin_trylock+0x13/0x60
? trace_hardirqs_on+0x1d/0x80
__sys_sendmsg+0x66/0xc0
do_syscall_64+0x6c/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f41defe5b34
Code: 15 e1 12 0f 00 f7 d8 64 89 02 b8 ff ff ff ff eb bf 0f 1f 44 00 00
f3 0f 1e fa 80 3d 35 95 0f 00 00 74 13 b8 2e 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 20 89 55
RSP: 002b:00007ffe5336ecc8 EFLAGS: 00000202 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f41defe5b34
RDX: 0000000000000000 RSI: 00007ffe5336ed30 RDI: 0000000000000003
RBP: 00007ffe5336eda0 R08: 0000000000000010 R09: 0000000000000001
R10: 00007ffe5336f6f9 R11: 0000000000000202 R12: 0000000000000003
R13: 0000000067452259 R14: 0000556ccc28b040 R15: 0000000000000000
</TASK>
[...]
Fixes: c8bd1f7f3e ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
[ pabeni: trimmed possibly troublesome separator ]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Due to target variable is being reassigned in npc_install_flow()
function, PF multicast rules are not getting installed.
This patch addresses the issue by fixing the "IF" condition
checks when rules are installed by AF.
Fixes: 6c40ca957f ("octeontx2-pf: Adds TC offload support").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241205113435.10601-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NXP S32G2xx/S32G3xx and S32R45 are automotive grade SoCs
that integrate one or two Synopsys DWMAC 5.10/5.20 IPs.
The basic driver supports only RGMII interface.
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-14-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-12-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-11-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-10-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-9-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-8-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
When in, remove dead code in kmb_eth_fix_mac_speed().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-7-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-6-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize a new helper function rgmii_clock().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-5-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The clock API clk_get_rate() returns unsigned long value.
Expand affected members of stmmac platform data and
convert the stmmac_clk_csr_set() and dwmac4_core_init() methods
to defining the unsigned long clk_rate local variables.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-3-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for CSR clock range up to 800 MHz.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jan Petrous (OSS) <jan.petrous@oss.nxp.com>
Link: https://patch.msgid.link/20241205-upstream_s32cc_gmac-v8-2-ec1d180df815@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This field is set but never used.
GWCA is rswitch CPU interface module which connects rswitch to the
host over AXI bus. Speed of the switch ports is not anyhow related to
GWCA operation.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241206192140.1714-2-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rswitch_ether_port_init_all(), only enabled ports are initialized.
Then, rswitch_ether_port_deinit_all() shall also only deinitialize
enabled ports.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241206192140.1714-1-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The module parameter qcaspi_pluggable controls if QCA7000 signature
should be checked at driver probe (current default) or not. Unfortunately
this could fail in case the chip is temporary in reset, which isn't under
total control by the Linux host. So disable this check per default
in order to avoid unexpected probe failures.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Storing the maximum clock speed in module parameter qcaspi_clkspeed
has the unintended side effect that the first probed instance
defines the value for all other instances. Fix this issue by storing
it in max_speed_hz of the relevant SPI device.
This fix keeps the priority of the speed parameter (module parameter,
device tree property, driver default). Btw this uses the opportunity
to get the rid of the unused member clkspeed.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These APIs are needed to support applications that use netlink to get VF
information from a PF driver.
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Link: https://patch.msgid.link/20241206064135.2331790-1-srasheed@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
t4_set_vf_mac_acl() uses pf to set mac addr, but t4vf_get_vf_mac_acl()
uses port number to get mac addr, this leads to error when an attempt
to set MAC address on VF's of PF2 and PF3.
This patch fixes the issue by using port number to set mac address.
Fixes: e0cdac65ba ("cxgb4vf: configure ports accessible by the VF")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241206062014.49414-1-anumula@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The set of bits that the VXLAN netdevice currently considers reserved is
defined by the features enabled at the netdevice construction. In order to
make this configurable, add an attribute, IFLA_VXLAN_RESERVED_BITS. The
payload is a pair of big-endian u32's covering the VXLAN header. This is
validated against the set of flags used by the various enabled VXLAN
features, and attempts to override bits used by an enabled feature are
bounced.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/c657275e5ceed301e62c69fe8e559e32909442e2.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code currently validates the VXLAN header in two ways: first by
comparing it with the set of reserved bits, constructed ahead of time
during the netdevice construction; and second by gradually clearing the
bits off a separate copy of VXLAN header, "unparsed". Drop the latter
validation method.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/4559f16c5664c189b3a4ee6f5da91f552ad4821c.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VXLAN driver so far has not increased the error counters for packets
that set reserved bits. It does so for other packet errors, so do it for
this case as well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/d096084167d56706d620afe5136cf37a2d34d1b9.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to make it possible to configure which bits in VXLAN header should
be considered reserved, introduce a new field vxlan_config::reserved_bits.
Have it cover the whole header, except for the VNI-present bit and the bits
for VNI itself, and have individual enabled features clear more bits off
reserved_bits.
(This is expressed as first constructing a used_bits set, and then
inverting it to get the reserved_bits. The set of used_bits will be useful
on its own for validation of user-set reserved_bits in a following patch.)
The patch also moves a comment relevant to the validation from the unparsed
validation site up to the new site. Logically this patch should add the new
comment, and a later patch that removes the unparsed bits would remove the
old comment. But keeping both legs in the same patch is better from the
history spelunking point of view.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/984dbf98d5940d3900268dbffaf70961f731d4a4.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Having a named reference to the VXLAN header is more handy than having to
conjure it anew through vxlan_hdr() on every use. Add a new variable and
convert several open-coded sites.
Additionally, convert one "unparsed" use to the new variable as well. Thus
the only "unparsed" uses that remain are the flag-clearing and the header
validity check at the end.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/2a0a940e883c435a0fdbcdc1d03c4858957ad00e.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The functions vxlan_remcsum() and vxlan_parse_gbp_hdr() take both the SKB
and the unparsed VXLAN header. Now that unparsed adjustment is handled
directly by vxlan_rcv(), drop this argument, and have the function derive
it from the SKB on its own.
vxlan_parse_gpe_proto() does not take SKB, so keep the header parameter.
However const it so that it's clear that the intention is that it does not
get changed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/5ea651f4e06485ba1a84a8eb556a457c39f0dfd4.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to migrate away from the use of unparsed to detect invalid flags,
move all the code that actually clears the flags from callees directly to
vxlan_rcv().
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/2857871d929375c881b9defe378473c8200ead9b.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
vxlan_sock.flags is constructed from vxlan_dev.cfg.flags, as the subset of
flags (named VXLAN_F_RCV_FLAGS) that is important from the point of view of
socket sharing. Attempts to reconfigure these flags during the vxlan netdev
lifetime are also bounced. It is therefore immaterial whether we access the
flags through the vxlan_dev or through the socket.
Convert the socket accesses to netdevice accesses in this separate patch to
make the conversions that take place in the following patches more obvious.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/5d237ffd731055e524d7b7c436de43358d8743d2.1733412063.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In configurations with 2 or more DSA clusters it will fail to allocate
unique MDIO bus names as only the switch ID is used, fix this by using
a combination of the tree ID and switch ID when needed
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241206204202.649912-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This development cycle featured multiple patchsets to ath12k to
support the new 802.11be MLO feature, although the feature is still
incomplete. Also in ath12k, there were other feature patches. In
ath11k, support was added for QCA6698AQ. And there was the usual set
of bug fixes and cleanups across most drivers, notable being the
addition of "noinline_for_stack" to some functions to avoid "stack
frame size" warnings when compiling with clang.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZ1cfJQAKCRAsFbugiYzL
e6csAP4yj+pdNHX6asbohlpJlohsyroOTEiPLZ9sP5qQ17eRRgEA6ycwqwJ/d39b
AyL2rJlxRQOz8sPbGeDvSAf3HkKN4Q4=
=81tw
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20241209' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.14
This development cycle featured multiple patchsets to ath12k to
support the new 802.11be MLO feature, although the feature is still
incomplete. Also in ath12k, there were other feature patches. In
ath11k, support was added for QCA6698AQ. And there was the usual set
of bug fixes and cleanups across most drivers, notable being the
addition of "noinline_for_stack" to some functions to avoid "stack
frame size" warnings when compiling with clang.
In commit 52250cbee7 ("mwifiex: use timeout variant for
wait_event_interruptible") it was noted that sometimes we seemed
to miss the signal that our host sleep settings took effect. A
10 second timeout was added to the code to make sure we didn't
hang forever waiting. It appears that this problem still exists
and we hit the timeout sometimes for Chromebooks in the field.
Recently on ChromeOS we've started setting the DPM watchdog
to trip if full system suspend takes over 10 seconds. Given
the timeout in the original patch, obviously we're hitting
the DPM watchdog before mwifiex gets a chance to timeout.
While we could increase the DPM watchdog in ChromeOS to avoid
this problem, it's probably better to simply decrease the
timeout. Any time we're waiting several seconds for the
firmware to respond it's likely that the firmware won't ever
respond. With that in mind, decrease the timeout in mwifiex
from 10 seconds to 5 seconds.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241127105709.4014302-1-treapking@chromium.org
This removes the following error log when stopping AP:
ieee80211 phy0: brcmf_vif_set_mgmt_ie: vndr ie set error : -52
It happened if:
1) previously wlan interface was in station mode (wpa_supplicant) and
connected to a hotspot
2) then started AP mode (hostapd)
3) and then stopped AP mode.
The error happened when it tried to clear BRCMF_VNDR_IE_PRBREQ_FLAG.
This flag is not set in `brcmf_config_ap_mgmt_ie`, but
BRCMF_VNDR_IE_ASSOCRSP_FLAG is set instead.
Signed-off-by: Renjaya Raga Zenta <ragazenta@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241121-brcmfmac-v1-1-02fc3fb427c2@gmail.com
'struct nla_policy' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
5062 528 0 5590 15d6 drivers/net/wireless/ti/wlcore/testmode.o
After:
=====
text data bss dec hex filename
5178 404 0 5582 15ce drivers/net/wireless/ti/wlcore/testmode.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/78810e3ebb74ddbd3a4538f182bf1143b89baba7.1731332414.git.christophe.jaillet@wanadoo.fr
The scatter-gather handling uses a pre-allocated list (with nents entries).
If the driver runs out of sg entries it will result in an oops. Let's detect
this instead and make the SDIO block transfer fail.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241108125609.107016-1-nvbolhuis@gmail.com
On port initialization, we configure the maximum frame length accepted
by the receive module associated with the port. This value is currently
written to the MAX_LEN field of the DEV10G_MAC_ENA_CFG register, when in
fact, it should be written to the DEV10G_MAC_MAXLEN_CFG register. Fix
this.
Fixes: 946e7fd505 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing port mirroring, the physical port to send the frame to, is
written to the FRMC_PORT_VAL field of the QFWD_FRAME_COPY_CFG register.
This field is 7 bits wide on sparx5 and 6 bits wide on lan969x, and has
a default value of 65 and 30, respectively (the number of front ports).
On mirror deletion, we set the default value of the monitor port to
65 for this field, in case no more ports exists for the mirror. Needless
to say, this will not fit the 6 bits on lan969x.
Fix this by correctly using the n_ports constant instead.
Fixes: 3f9e46347a ("net: sparx5: use SPX5_CONST for constants which already have a symbol")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FDMA handler is responsible for scheduling a NAPI poll, which will
eventually fetch RX packets from the FDMA queue. Currently, the FDMA
handler is run in a threaded context. For some reason, this kills
performance. Admittedly, I did not do a thorough investigation to see
exactly what causes the issue, however, I noticed that in the other
driver utilizing the same FDMA engine, we run the FDMA handler in hard
IRQ context.
Fix this performance issue, by running the FDMA handler in hard IRQ
context, not deferring any work to a thread.
Prior to this change, the RX UDP performance was:
Interval Transfer Bitrate Jitter
0.00-10.20 sec 44.6 MBytes 36.7 Mbits/sec 0.027 ms
After this change, the rx UDP performance is:
Interval Transfer Bitrate Jitter
0.00-9.12 sec 1.01 GBytes 953 Mbits/sec 0.020 ms
Fixes: 10615907e9 ("net: sparx5: switchdev: adding frame DMA functionality")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depmod reports a cyclic dependency between modules sparx5-switch.ko and
lan969x-switch.ko:
depmod: ERROR: Cycle detected: lan969x_switch -> sparx5_switch -> lan969x_switch
depmod: ERROR: Found 2 modules in dependency cycles!
make[2]: *** [scripts/Makefile.modinst:132: depmod] Error 1
make: *** [Makefile:224: __sub-make] Error 2
This makes sense, as they both require symbols from each other.
Fix this by compiling lan969x support into the sparx5-switch.ko module.
In order to do this, in a sensible way, we move the lan969x/ dir into
the sparx5/ dir and do some code cleanup of code that is no longer
required.
After this patch, depmod will no longer complain, as lan969x support is
compiled into the sparx5-swicth.ko module, and can no longer be compiled
as a standalone module.
Fixes: 98a0111960 ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware is initialized and netdev transmit flow is
hooked up for outbound ipsec crypto offload, so finally
enable ipsec offload.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to use hardware offload for outbound ipsec crypto
mode if security association (SA) is set for a given skb.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare and submit crypto hardware (CPT) instruction for
outbound ipsec crypto offload. The CPT instruction have
authentication offset, IV offset and encapsulation offset
in input packet. Also provide SA context pointer which have
details about algo, keys, salt etc. Crypto hardware encrypt,
authenticate and provide the ESP packet to networking hardware.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to add and delete Security Association
(SA) xfrm ops. Hardware maintains SA context in memory allocated
by software. Each SA context is 128 byte aligned and size of
each context is multiple of 128-byte. Add support for transport
and tunnel ipsec mode, ESP protocol, aead aes-gcm-icv16, key size
128/192/256-bits with 32bit salt.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One crypto hardware logical function (cpt-lf) per netdev is
required for outbound ipsec crypto offload. Allocate, attach
and initialize one crypto hardware function when enabling
outbound ipsec crypto offload. Crypto hardware function will
be detached and freed on disabling outbound ipsec crypto
offload.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX can assert backpressure to CPT on the NIX<=>CPT link.
Keep the backpressure disabled for now. NIX block anyways
handles backpressure asserted by MAC due to PFC or flow
control pkts.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move skb fragment map/unmap function to common file
so as to reuse same for outbound IPsec crypto offload
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Crypto hardware need write permission for in-place encrypt
or decrypt operation on skb-data to support IPsec crypto
offload. That patch uses skb_unshare to make skb data writeable
for ipsec crypto offload and map skb fragment memory as
device read-write.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refine the if statement to improve readability.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241206084851.760475-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An unsupported RX filter will leave the port with TX timestamping still
applied as per the new request, rather than the old setting. When
parsing the tx_type, don't apply it just yet, but delay that until after
we've parsed the rx_filter as well (and potentially returned -ERANGE for
that).
Similarly, copy_to_user() may fail, which is a rare occurrence, but
should still be treated by unwinding what was done.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-6-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Felix DSA driver presents unique challenges that make the simplistic
ocelot PTP TX timestamping procedure unreliable: any transmitted packet
may be lost in hardware before it ever leaves our local system.
This may happen because there is congestion on the DSA conduit, the
switch CPU port or even user port (Qdiscs like taprio may delay packets
indefinitely by design).
The technical problem is that the kernel, i.e. ocelot_port_add_txtstamp_skb(),
runs out of timestamp IDs eventually, because it never detects that
packets are lost, and keeps the IDs of the lost packets on hold
indefinitely. The manifestation of the issue once the entire timestamp
ID range becomes busy looks like this in dmesg:
mscc_felix 0000:00:00.5: port 0 delivering skb without TX timestamp
mscc_felix 0000:00:00.5: port 1 delivering skb without TX timestamp
At the surface level, we need a timeout timer so that the kernel knows a
timestamp ID is available again. But there is a deeper problem with the
implementation, which is the monotonically increasing ocelot_port->ts_id.
In the presence of packet loss, it will be impossible to detect that and
reuse one of the holes created in the range of free timestamp IDs.
What we actually need is a bitmap of 63 timestamp IDs tracking which one
is available. That is able to use up holes caused by packet loss, but
also gives us a unique opportunity to not implement an actual timer_list
for the timeout timer (very complicated in terms of locking).
We could only declare a timestamp ID stale on demand (lazily), aka when
there's no other timestamp ID available. There are pros and cons to this
approach: the implementation is much more simple than per-packet timers
would be, but most of the stale packets would be quasi-leaked - not
really leaked, but blocked in driver memory, since this algorithm sees
no reason to free them.
An improved technique would be to check for stale timestamp IDs every
time we allocate a new one. Assuming a constant flux of PTP packets,
this avoids stale packets being blocked in memory, but of course,
packets lost at the end of the flux are still blocked until the flux
resumes (nobody left to kick them out).
Since implementing per-packet timers is way too complicated, this should
be good enough.
Testing procedure:
Persistently block traffic class 5 and try to run PTP on it:
$ tc qdisc replace dev swp3 parent root taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0xdf 100000 flags 0x2
[ 126.948141] mscc_felix 0000:00:00.5: port 3 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
$ ptp4l -i swp3 -2 -P -m --socket_priority 5 --fault_reset_interval ASAP --logSyncInterval -3
ptp4l[70.351]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.354]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.358]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 70.394583] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[70.406]: timed out while polling for tx timestamp
ptp4l[70.406]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[70.406]: port 1 (swp3): send peer delay response failed
ptp4l[70.407]: port 1 (swp3): clearing fault immediately
ptp4l[70.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 71.394858] mscc_felix 0000:00:00.5: port 3 timestamp id 1
ptp4l[71.400]: timed out while polling for tx timestamp
ptp4l[71.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[71.401]: port 1 (swp3): send peer delay response failed
ptp4l[71.401]: port 1 (swp3): clearing fault immediately
[ 72.393616] mscc_felix 0000:00:00.5: port 3 timestamp id 2
ptp4l[72.401]: timed out while polling for tx timestamp
ptp4l[72.402]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[72.402]: port 1 (swp3): send peer delay response failed
ptp4l[72.402]: port 1 (swp3): clearing fault immediately
ptp4l[72.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 73.395291] mscc_felix 0000:00:00.5: port 3 timestamp id 3
ptp4l[73.400]: timed out while polling for tx timestamp
ptp4l[73.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[73.400]: port 1 (swp3): send peer delay response failed
ptp4l[73.400]: port 1 (swp3): clearing fault immediately
[ 74.394282] mscc_felix 0000:00:00.5: port 3 timestamp id 4
ptp4l[74.400]: timed out while polling for tx timestamp
ptp4l[74.401]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[74.401]: port 1 (swp3): send peer delay response failed
ptp4l[74.401]: port 1 (swp3): clearing fault immediately
ptp4l[74.953]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 75.396830] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 75.405760] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[75.410]: timed out while polling for tx timestamp
ptp4l[75.411]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[75.411]: port 1 (swp3): send peer delay response failed
ptp4l[75.411]: port 1 (swp3): clearing fault immediately
(...)
Remove the blocking condition and see that the port recovers:
$ same tc command as above, but use "sched-entry S 0xff" instead
$ same ptp4l command as above
ptp4l[99.489]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.490]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.492]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 100.403768] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 100.412545] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 1 which seems lost
[ 100.421283] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 2 which seems lost
[ 100.430015] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 3 which seems lost
[ 100.438744] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 4 which seems lost
[ 100.447470] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 100.505919] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[100.963]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 101.405077] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 101.507953] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.405405] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.509391] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.406003] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.510011] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.405601] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.510624] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[104.965]: selected best master clock d858d7.fffe.00ca6d
ptp4l[104.966]: port 1 (swp3): assuming the grand master role
ptp4l[104.967]: port 1 (swp3): LISTENING to GRAND_MASTER on RS_GRAND_MASTER
[ 105.106201] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.232420] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.359001] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.405500] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.485356] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.511220] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.610938] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.737237] mscc_felix 0000:00:00.5: port 3 timestamp id 0
(...)
Notice that in this new usage pattern, a non-congested port should
basically use timestamp ID 0 all the time, progressing to higher numbers
only if there are unacknowledged timestamps in flight. Compare this to
the old usage, where the timestamp ID used to monotonically increase
modulo OCELOT_MAX_PTP_ID.
In terms of implementation, this simplifies the bookkeeping of the
ocelot_port :: ts_id and ptp_skbs_in_flight. Since we need to traverse
the list of two-step timestampable skbs for each new packet anyway, the
information can already be computed and does not need to be stored.
Also, ocelot_port->tx_skbs is always accessed under the switch-wide
ocelot->ts_id_lock IRQ-unsafe spinlock, so we don't need the skb queue's
lock and can use the unlocked primitives safely.
This problem was actually detected using the tc-taprio offload, and is
causing trouble in TSN scenarios, which Felix (NXP LS1028A / VSC9959)
supports but Ocelot (VSC7514) does not. Thus, I've selected the commit
to blame as the one adding initial timestamping support for the Felix
switch.
Fixes: c0bcf53766 ("net: dsa: ocelot: add hardware timestamping support for Felix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_txtstamp() is a threaded IRQ handler, requested explicitly as
such by both ocelot_ptp_rdy_irq_handler() and vsc9959_irq_handler().
As such, it runs with IRQs enabled, and not in hardirq context. Thus,
ocelot_port_add_txtstamp_skb() has no reason to turn off IRQs, it cannot
be preempted by ocelot_get_txtstamp(). For the same reason,
dev_kfree_skb_any_reason() will always evaluate as kfree_skb_reason() in
this calling context, so just simplify the dev_kfree_skb_any() call to
kfree_skb().
Also, ocelot_port_txtstamp_request() runs from NET_TX softirq context,
not with hardirqs enabled. Thus, ocelot_get_txtstamp() which shares the
ocelot_port->tx_skbs.lock lock with it, has no reason to disable hardirqs.
This is part of a larger rework of the TX timestamping procedure.
A logical subportion of the rework has been split into a separate
change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This condition, theoretically impossible to trigger, is not really
handled well. By "continuing", we are skipping the write to SYS_PTP_NXT
which advances the timestamp FIFO to the next entry. So we are reading
the same FIFO entry all over again, printing stack traces and eventually
killing the kernel.
No real problem has been observed here. This is part of a larger rework
of the timestamp IRQ procedure, with this logical change split out into
a patch of its own. We will need to "goto next_ts" for other conditions
as well.
Fixes: 9fde506e0c ("net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If ocelot_port_add_txtstamp_skb() fails, for example due to a full PTP
timestamp FIFO, we must undo the skb_clone_sk() call with kfree_skb().
Otherwise, the reference to the skb clone is lost.
Fixes: 52849bcf00 ("net: mscc: ocelot: avoid overflowing the PTP timestamp FIFO")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report the PCS in-band capabilities to phylink for the Lynx PCS.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tJ8NM-006L5J-AH@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently tun checks the group permission even if the user have matched.
Besides going against the usual permission semantic, this has a
very interesting implication: if the tun group is not among the
supplementary groups of the tun user, then effectively no one can
access the tun device. CAP_SYS_ADMIN still can, but its the same as
not setting the tun ownership.
This patch relaxes the group checking so that either the user match
or the group match is enough. This avoids the situation when no one
can access the device even though the ownership is properly set.
Also I simplified the logic by removing the redundant inversions:
tun_not_capable() --> !tun_capable()
Signed-off-by: Stas Sergeev <stsp2@yandex.ru>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20241205073614.294773-1-stsp2@yandex.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 66600fac7a ("net: stmmac: TSO: Fix unbalanced DMA map/unmap
for non-paged SKB data") moved the assignment of tx_skbuff_dma[]'s
members to be later in stmmac_tso_xmit().
The buf (dma cookie) and len stored in this structure are passed to
dma_unmap_single() by stmmac_tx_clean(). The DMA API requires that
the dma cookie passed to dma_unmap_single() is the same as the value
returned from dma_map_single(). However, by moving the assignment
later, this is not the case when priv->dma_cap.addr64 > 32 as "des"
is offset by proto_hdr_len.
This causes problems such as:
dwc-eth-dwmac 2490000.ethernet eth0: Tx DMA map failed
and with DMA_API_DEBUG enabled:
DMA-API: dwc-eth-dwmac 2490000.ethernet: device driver tries to +free DMA memory it has not allocated [device address=0x000000ffffcf65c0] [size=66 bytes]
Fix this by maintaining "des" as the original DMA cookie, and use
tso_des to pass the offset DMA cookie to stmmac_tso_allocator().
Full details of the crashes can be found at:
https://lore.kernel.org/all/d8112193-0386-4e14-b516-37c2d838171a@nvidia.com/https://lore.kernel.org/all/klkzp5yn5kq5efgtrow6wbvnc46bcqfxs65nz3qy77ujr5turc@bwwhelz2l4dw/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Fixes: 66600fac7a ("net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/E1tJXcx-006N4Z-PC@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bareudp uses the TSTATS infrastructure (dev_sw_netstats_*()) for RX
packet counters. It was also recently converted to use the device core
stats (dev_core_stats_*()) for RX and TX drops (see commit 788d5d655b
("bareudp: Use pcpu stats to update rx_dropped counter.")).
Since core stats are to be avoided in drivers, and for consistency with
VXLAN and Geneve, let's convert packet stats handling to DSTATS, which
can handle RX/TX stats and packet drops. Statistics that don't fit
DSTATS are still updated atomically with DEV_STATS_INC().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/0f4f8448db3ff449ac6e939872b28cf3f8982da7.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geneve uses the TSTATS infrastructure (dev_sw_netstats_*()) for RX
packet counters. All other counters are handled using atomic increments
with DEV_STATS_INC().
Let's convert packet stats handling to DSTATS, which has a per-cpu
counter for packet drops too, to avoid the cost of atomic increments
in these cases. Statistics that don't fit DSTATS are still updated
atomically with DEV_STATS_INC().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/7af5c09f3c26f0f231fbe383822ca5d1ce0278fa.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VXLAN uses the TSTATS infrastructure (dev_sw_netstats_*()) for RX and
TX packet counters. It also uses the device core stats
(dev_core_stats_*()) for RX and TX drops.
Let's consolidate that using the DSTATS infrastructure, which can
handle both packet counters and packet drops. Statistics that don't
fit DSTATS are still updated atomically with DEV_STATS_INC().
While there, convert the "len" variable of vxlan_encap_bypass() to
unsigned int, to respect the types of skb->len and
dev_dstats_[rt]x_add().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/145558b184b3cda77911ca5682b6eb83c3ffed8e.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently vrf is the only module that uses NETDEV_PCPU_STAT_DSTATS.
In order to make this kind of statistics available to other modules,
we need to define the update functions in netdevice.h.
Therefore, let's define dev_dstats_*() functions for RX and TX packet
updates (packets, bytes and drops). Use these new functions in vrf.c
instead of vrf_rx_stats() and the other manual counter updates.
While there, update the type of the "len" variables to "unsigned int",
so that there're aligned with both skb->len and the new dstats update
functions.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/d7a552ee382c79f4854e7fcc224cf176cd21150d.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update `lan78xx_dataport_write` and `lan78xx_deferred_multicast_write`
to:
- Handle errors during register read/write operations.
- Exit immediately on errors and log them using `%pe` for clarity.
- Avoid silent failures by propagating error codes properly.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-11-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update `lan78xx_irq_bus_sync_unlock` to handle errors in register
read/write operations. If an error occurs, log it and exit the function
appropriately. This ensures proper handling of failures during IRQ
synchronization.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-10-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Improve error handling in `lan78xx_set_rx_max_frame_length` by:
- Checking return values from register read/write operations and
propagating errors.
- Exiting immediately on failure to ensure proper error reporting.
In `lan78xx_change_mtu`, log errors when changing MTU fails, using `%pe`
for clear error representation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-9-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert `lan78xx_init_ltm` to return error codes and handle errors
properly. Previously, errors during the LTM initialization process were
not propagated, potentially leading to undetected issues. This patch
ensures:
- Errors in `lan78xx_read_reg` and `lan78xx_write_reg` are checked and
handled.
- Errors are logged with detailed messages using `%pe` for clarity.
- The function exits immediately on error, returning the error code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-8-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refine error handling in EEPROM and OTP read/write functions by:
- Return error values immediately upon detection.
- Avoid overwriting correct error codes with `-EIO`.
- Preserve initial error codes as they were appropriate for specific
failures.
- Use `-ETIMEDOUT` for timeout conditions instead of `-EIO`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure proper error handling in `lan78xx_mdiobus_read` and
`lan78xx_mdiobus_write` by checking return values of register read/write
operations and returning errors to the caller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace integer error codes with the `%pe` format specifier in register
read and write error messages. This change provides human-readable error
strings, making logs more informative and debugging easier.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move following functions to avoid forward declarations in the code:
- lan78xx_start_hw()
- lan78xx_stop_hw()
- lan78xx_flush_fifo()
- lan78xx_start_tx_path()
- lan78xx_stop_tx_path()
- lan78xx_flush_tx_fifo()
- lan78xx_start_rx_path()
- lan78xx_stop_rx_path()
- lan78xx_flush_rx_fifo()
These functions will be used in an upcoming PHYlink migration patch.
No modifications to the functionality of the code are made.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the KSZ9031RNX PHY fixup from the lan78xx driver. The fixup applied
specific RGMII pad skew configurations globally, but these settings violate the
RGMII specification and cause more harm than benefit.
Key issues with the fixup:
1. **Non-Compliant Timing**: The fixup's delay settings fall outside the RGMII
specification requirements of 1.5 ns to 2.0 ns:
- RX Path: Total delay of **2.16 ns** (PHY internal delay of 1.2 ns + 0.96
ns skew).
- TX Path: Total delay of **0.96 ns**, significantly below the RGMII minimum
of 1.5 ns.
2. **Redundant or Incorrect Configurations**:
- The RGMII skew registers written by the fixup do not meaningfully alter
the PHY's default behavior and fail to account for its internal delays.
- The TX_DATA pad skew was not configured, relying on power-on defaults
that are insufficient for RGMII compliance.
3. **Micrel Driver Support**: By setting `PHY_INTERFACE_MODE_RGMII_ID`, the
Micrel driver can calculate and assign appropriate skew values for the
KSZ9031 PHY. This ensures better timing configurations without relying on
external fixups.
4. **System Interference**: The fixup applied globally, reconfiguring all
KSZ9031 PHYs in the system, even those unrelated to the LAN78xx adapter.
This could lead to unintended and harmful behavior on unrelated interfaces.
While the fixup is removed, a better mechanism is still needed to dynamically
determine the optimal combination of PHY and MAC delays to fully meet RGMII
requirements without relying on Device Tree or global fixups. This would allow
for robust operation across different hardware configurations.
The Micrel driver is capable of using the interface mode value to calculate and
apply better skew values, providing a configuration much closer to the RGMII
specification than the fixup. Removing the fixup ensures better default
behavior and prevents harm to other system interfaces.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the PHY fixup for the LAN8835 PHY in the lan78xx driver due to
the following reasons:
- There is no publicly available information about the LAN8835 PHY.
However, it appears to be the integrated PHY used in the LAN7800 and
LAN7850 USB Ethernet controllers. These PHYs use the GMII interface,
not RGMII as configured by the fixup.
- The correct driver for handling the LAN8835 PHY functionality is the
Microchip PHY driver (`drivers/net/phy/microchip.c`), which properly
supports these integrated PHYs.
- The PHY ID `0x0007C130` is actually used by the LAN8742A PHY, which
only supports RMII. This interface is incompatible with the LAN78xx
MAC, as the LAN7801 (the only LAN78xx version without an integrated
PHY) supports only RGMII.
- The mask applied for this fixup is overly broad, inadvertently
covering both Microchip LAN88xx PHYs and unrelated SMSC LAN8742A PHYs,
leading to potential conflicts with other devices.
- Testing has shown that removing this fixup for LAN7800 and LAN7850
does not result in any noticeable difference in functionality, as the
Microchip PHY driver (`drivers/net/phy/microchip.c`) handles all
necessary configurations for these integrated PHYs.
- Registering this fixup globally (not limited to USB devices) risks
conflicts by unintentionally modifying other interfaces whenever a
LAN7801 adapter is connected to the system.
Note that both LAN7800 and LAN7850 USB Ethernet controllers use an
integrated PHY with the ID `0x0007C132`. Additionally, the LAN7515, a
specialized part for Raspberry Pi, includes an integrated LAN7800 USB
Ethernet controller and USB hub in a multifunctional chip design, and it
also uses the same PHY ID (`0x0007C132`).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the phy_ethtool_get_eee() documentation to make it clear that
all members of struct ethtool_keee are written by this function.
keee.supported, keee.advertised, keee.lp_advertised and keee.eee_active
are all written by genphy_c45_ethtool_get_eee().
keee.tx_lpi_timer, keee.tx_lpi_enabled and keee.eee_enabled are all
written by eeecfg_to_eee().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1tJ9JH-006LIz-SO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All callers to genphy_c45_eee_is_active() now pass NULL as the
is_enabled argument, which means we never use the value computed
in this function. Remove the argument and clean up this function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tJ9JC-006LIt-Ne@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genphy_c45_ethtool_get_eee() is only called from phy_ethtool_get_eee(),
which then calls eeecfg_to_eee(). eeecfg_to_eee() will overwrite
keee.eee_enabled, so there's no point setting keee.eee_enabled in
genphy_c45_ethtool_get_eee(). Remove this assignment.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tJ9J7-006LIn-Jr@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than calling genphy_c45_ethtool_get_eee() to retrieve whether
EEE is enabled, use the value stored in the phy_device eee_cfg
structure.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tJ9J2-006LIh-Fl@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing code is using RSS profile to determine IPV4/IPV6 GSO type
on all chips older than 5760X. This won't work on 5750X chips that may
be using modified RSS profiles. This commit from 2018 has updated the
driver to not use RSS profile for HW GRO packets on newer chips:
50f011b63d ("bnxt_en: Update RSS setup and GRO-HW logic according to the latest spec.")
However, a recent commit to add support for the newest 5760X chip broke
the logic. If the GRO packet needs to be re-segmented by the stack, the
wrong GSO type will cause the packet to be dropped.
Fix it to only use RSS profile to determine GSO type on the oldest
5730X/5740X chips which cannot use the new method and is safe to use the
RSS profiles.
Also fix the L3/L4 hash type for RX packets by not using the RSS
profile for the same reason. Use the ITYPE field in the RX completion
to determine L3/L4 hash types correctly.
Fixes: a7445d6980 ("bnxt_en: Add support for new RX and TPA_START completion types for P7")
Reviewed-by: Colin Winegarden <colin.winegarden@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241204215918.1692597-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
get resource + request_mem_region + ioremap can all be done by a single
function.
Replace them with devm_platform_get_and_ioremap_resource or\
devm_platform_ioremap_resource where res is not used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> # sja1000_platform.c
Link: https://patch.msgid.link/20241203231337.182391-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ucc_geth is quite capable in terms of supported interfaces, and even
includes an externally controlled PCS (well, TBI). Port that driver to
phylink.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of parallel MII interfaces also exist in a "Reduced" mode,
usually with higher clock rates and fewer data lines, to ease the
hardware design. This is what the 'R' stands for in RGMII, RMII, RTBI,
RXAUI, etc.
The UCC Geth controller has a special configuration bit that needs to be
set when the MII mode is one of the supported reduced modes.
Add a local helper for that.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The uec_configure_serdes() function deals with serialized linkmodes
settings. It's used during the link bringup sequence. It is planned to
be used during the phylink conversion for mac configuration, but it
needs to me moved around in the process. To make the phylink port
clearer, this commit moves the function without any feature change.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The preamble length can be configured in ucc_geth, however it just
ends-up always being configured to 7 bytes, as nothing ever changes the
default value of 7.
Make that value the default value when the MACCFG2 register gets
initialized, and remove the code to configure that value altogether.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The frame length check is configured when the phy interface is setup.
However, it's configured according to an internal flag that is always
false. So, just make so that we disable the relevant bit in the MACCFG2
register upon accessing it for other MAC configuration operations.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WoL opts are represented through a bitmask stored in a u32. As this
mask is copied as-is in the driver, make sure we use the exact same type
to store them internally.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The get/set_wol ethtool ops rely on querying the PHY for its WoL
capabilities, checking for the presence of a PHY and a PHY interrupts
isn't enough. Address that by cleaning up the WoL configuration
sequence.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this driver pre-dates phylib, it uses a private pointer to get a
reference to the attached phy_device. Drop that pointer and use the
netdev's pointer instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparing the phylink conversion, split the adjust_link callbaclk, by
clearly separating the mac configuration, link_up and link_down phases.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In april 2007, ucc_geth was converted to phylib with :
commit 728de4c927 ("ucc_geth: migrate ucc_geth to phylib").
In that commit, the device-tree property "interface", that could be used to
retrieve the PHY interface mode was deprecated.
DTS files that still used that property were converted along the way, in
the following commit, also dating from april 2007 :
commit 0fd8c47ccc ("[POWERPC] Replace undocumented interface properties in dts files")
17 years later, there's no users of that property left and I hope it's
safe to say we can remove support from that in the ucc_geth driver,
making the probe() function a bit simpler.
Should there be any users that have a DT that was generated when 2.6.21 was
cutting-edge, print an error message with hints on how to convert the
devicetree if the 'interface' property is found.
With that property gone, we can greatly simplify the parsing of the
phy-interface-mode from the devicetree by using of_get_phy_mode(),
allowing the removal of the open-coded parsing in the driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dr_domain_add_vport_cap() function generally returns NULL on error
but sometimes we want it to return ERR_PTR(-EBUSY) so the caller can
retry. The problem here is that "ret" can be either -EBUSY or -ENOMEM
and if it's and -ENOMEM then the error pointer is propogated back and
eventually dereferenced in dr_ste_v0_build_src_gvmi_qpn_tag().
Fixes: 11a45def2e ("net/mlx5: DR, Add support for SF vports")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/07477254-e179-43e2-b1b3-3b9db4674195@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, during mac80211 allocate and register single device is
considered for the registration. But, in future, during multi device
group abstraction is introduced, all the devices has to be combined
together as a single abstraction and then hardware should be allocated.
All the devices in the group should be combined together only if it
supports inter device mlo capability. The decision of whether to combine
the devices or not can be based on the mlo capability flag in
ath12k_hw_group.
By default, mlo_capable flag in the group would be set as false. During
QMI PHY capability exchange, only when we have more than one chip in the
group or if one chip, then that chip supports inter MLO, then mlo_capable
flag in the group will be enabled.
Add changes to introduce mlo_capable flag for device group and refactor
ath12k_mac_hw_allocate() api based on device group (ag) rather than
device (ab).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
QMI host capability has the information regarding MLO parameters such as
device_id, MLO capability, group id and the information of each devices
involved in the group and sent immediately on QMI server arrive event.
Currently, only one device is involved in the group and hence, single
device information is sent as part of MLO capability of host.
But, in future when multi device group abstraction is introduced, host
should send all the device information involved in the group as part
of QMI MLO host capability rather than single device. Hence, sending
QMI host capability immediately on server arrive of a device might not
be ideal for multi device group abstraction as the details of other
devices in the group would not be available.
Hence, once QMI server arrive event is received, request for QMI PHY
capabilities of device, and defer the host capability send for that device.
After QMI PHY capability is received for all the devices in the group
trigger the host capability event for the deferred devices in the group.
Hence, add changes to defer the QMI host capability event until the device
group is ready and then resume the QMI exchange for all the device with
host capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, hardware abstractions (ah) of different radio bands are tightly
coupled to a single device (ab). But, with hardware device group abstraction
(ag), multiple radios across different devices in a group can form different
combinations of hardware abstractions (ah) within the group. Hence, the mapping
between ah to ab can be removed and instead it can be mapped with struct
ath12k_hw_group (ag).
Current mapping between struct ath12k_hw (ah), struct ath12k_base (ab) and struct
ath12k_hw_group (ag):
+------------------------------------------------+
| +-------------------------------------+ |
| | +---------------+ +---------------+ | |
| | |ath12k_hw (ah) | |ath12k_hw (ah) | | |
| | +---------------+ +---------------+ | |
| | | |
| | +-----------+ | +-----------+ | |
| | | ar (2GHz) | | | ar (5GHz) | | |
| | +-----------+ | +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------+
After hardware device group abstraction moving ah array out of ab to ag:
+----------------------------------------------+
| +---------------+ +---------------+ |
| |ath12k_hw (ah) | |ath12k_hw (ah) | |
| +---------------+ +---------------+ |
| +-------------------------------------+ |
| | +-----------+ +-----------+ | |
| | | ar (2GHz) | | ar (5GHz) | | |
| | +-----------+ +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+----------------------------------------------+
This decoupling of struct ath12k_hw (ah) from struct ath12k_base (ab) and
mapping it to struct ath12k_hw_group (ag) will help in forming different
combinations of multi-link devices.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, mac allocate/register and core_pdev_create are initiated immediately
when QMI firmware ready event is received for a particular device. With
hardware device group abstraction, QMI firmware ready event can be received
simultaneously for different devices in the group and so, it should not be
registered immediately rather it has to be deferred until all devices in the
group has received QMI firmware ready.
To handle this, refactor the code of core start to have registering within
ath12k_core_hw_group_start() and unregistering in ath12k_core_hw_group_stop().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, single device is probed, and once firmware is ready, the device
is registered to mac80211. For Multi-Link Operation, different bands of
different devices or same device are part of a single wiphy and for
this, hardware device group abstraction is needed.
Hardware device group abstraction - when there are multiple devices (with
single radio or dual radio) that are connected by any means of interface
for communicating between them, then these devices can be combined
together as a single group using a group id to form a group abstraction
and register to mac80211.
The grouping information of multiple devices would be based on device tree
during device probe (will be implemented in future patches). If no such
information is available, then a single device will be part of group abstraction
and registered to mac80211, else multiple devices advertised in device tree are
combined and then registered to mac80211.
For device group abstraction, a base structure ath12k_hw_group (ag) and the
helpers are implemented. These helpers are used during device probe and mapping
the group to the devices involved.
An illustration of how multiple devices might be combined together in
future based on group id:
+------------------------------------------------------------------------+
| +-------------------------------------+ +-------------------+ |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | | ar (2GHz) | | | | ar (5GHz) | | | | ar (6GHz) | | |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | ath12k_base (ab) | | ath12k_base (ab) | |
| | (Dual band device) | | | |
| +-------------------------------------+ +-------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------------------------------+
In the above representation, two devices are combined into single group
based on group id.
Add base code changes where single device would be part of a group with an
invalid group id forming an group abstraction. Multi device grouping will
be introduced in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the mlo_capable_flags in ath12k_base is used to indicate whether
the chip supports inter (QCN9274) or intra (WCN7850) chip MLO. However, it’s
possible that the chip supports neither, especially with older firmware
versions. Additionally, if intra chip MLO is not supported, inter chip MLO will
also be non-functional. Therefore, having two separate flags for this is
unnecessary.
Therefore, rename this flag to single_chip_mlo_supp. At the same time convert
it into a bool data type. Also, get rid of the enums defined earlier.
For the QCN9274 family of chipsets, this will be set only when firmware
advertises the support during the QMI exchange.
For the WCN7850 family of chipsets, since the event is not supported,
assumption is made that single chip MLO is supported.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When hardware device group abstraction is introduced, a group abstraction is
registered to mac80211 rather than a particular single device. So we cannot
set the device registered when the QMI firmware ready event is received, only
after all the devices in group have received the event. To do that set and
unset ATH12K_FLAG_REGISTERED flag inside ath12k_mac_register() and
ath12k_mac_unregister() respectively.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current release - regressions:
- rtnetlink: fix double call of rtnl_link_get_net_ifla()
- tcp: populate XPS related fields of timewait sockets
- ethtool: fix access to uninitialized fields in set RXNFC command
- selinux: use sk_to_full_sk() in selinux_ip_output()
Current release - new code bugs:
- net: make napi_hash_lock irq safe
- eth: bnxt_en: support header page pool in queue API
- eth: ice: fix NULL pointer dereference in switchdev
Previous releases - regressions:
- core: fix icmp host relookup triggering ip_rt_bug
- ipv6:
- avoid possible NULL deref in modify_prefix_route()
- release expired exception dst cached in socket
- smc: fix LGR and link use-after-free issue
- hsr: avoid potential out-of-bound access in fill_frame_info()
- can: hi311x: fix potential use-after-free
- eth: ice: fix VLAN pruning in switchdev mode
Previous releases - always broken:
- netfilter:
- ipset: hold module reference while requesting a module
- nft_inner: incorrect percpu area handling under softirq
- can: j1939: fix skb reference counting
- eth: mlxsw: use correct key block on Spectrum-4
- eth: mlx5: fix memory leak in mlx5hws_definer_calc_layout
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEg1AjqC77wbdLX2LbKSR5jcyPE6QFAmdRve4SHHBhYmVuaUBy
ZWRoYXQuY29tAAoJECkkeY3MjxOk/TUQAItDVkTQDiAUUqd0TDH2SSnboxXozcMF
fKVrdWulFAOe7qcajUqjkzvTDjAOw9Xbfh8rEiFBLaXmUzSUT2eqbm2VahvWIR5/
k08v7fTTuCNzEwhnbQlsZ47Nd26LJVPwOvbtE/4V8d50pU/serjWuI/74tUCWAjn
DQOjyyqRjKgKKY+WWCQ6g4tVpD//DB4Sj15GiE3MhlW1f08AAnPJSe2oTaq0RZBG
nXo7abOGn8x3RYilrlp/ZwWYuNpVI4oF+qmp+t/46NV+7ER1JgrC97k0kFyyCYVD
g7vBvFjvA7vDmiuzfsOW2n7IRdcfBtkfi8UJYOIvVgJg7KDF0DXoxj3qD4FagI35
RWRMJw+PoNlFFkPprlp0we/19jPJWOO6rx+AOMEQD78jrH7NoFQ/+eeBf/nppfjy
wX0LD1aQsgPk2ju0I8GbcM/qaJ81EJUiYYVLJHieH0+vvmqts8cMDRLZf5t08EHa
myXcRGB9N8gjguGp5mdR5KmtY82zASlNC0PbDp3nlPYc3e/opCmMRYGjBohO+vqn
n7u250WThPwiBtOwYmSbcK7zpS034/VX0ufnTT2X3MWnFGGNDv6XVmho/OBuCHqJ
m/EiJo/D9qVGAIql/vAxN9a4lQKrcZgaMzCyEPYCf7rtLmzx7sfyHWbf/GZlUAU/
9dUUfWqCbZcL
=nkPk
-----END PGP SIGNATURE-----
Merge tag 'net-6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can and netfilter.
Current release - regressions:
- rtnetlink: fix double call of rtnl_link_get_net_ifla()
- tcp: populate XPS related fields of timewait sockets
- ethtool: fix access to uninitialized fields in set RXNFC command
- selinux: use sk_to_full_sk() in selinux_ip_output()
Current release - new code bugs:
- net: make napi_hash_lock irq safe
- eth:
- bnxt_en: support header page pool in queue API
- ice: fix NULL pointer dereference in switchdev
Previous releases - regressions:
- core: fix icmp host relookup triggering ip_rt_bug
- ipv6:
- avoid possible NULL deref in modify_prefix_route()
- release expired exception dst cached in socket
- smc: fix LGR and link use-after-free issue
- hsr: avoid potential out-of-bound access in fill_frame_info()
- can: hi311x: fix potential use-after-free
- eth: ice: fix VLAN pruning in switchdev mode
Previous releases - always broken:
- netfilter:
- ipset: hold module reference while requesting a module
- nft_inner: incorrect percpu area handling under softirq
- can: j1939: fix skb reference counting
- eth:
- mlxsw: use correct key block on Spectrum-4
- mlx5: fix memory leak in mlx5hws_definer_calc_layout"
* tag 'net-6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
net :mana :Request a V2 response version for MANA_QUERY_GF_STAT
net: avoid potential UAF in default_operstate()
vsock/test: verify socket options after setting them
vsock/test: fix parameter types in SO_VM_SOCKETS_* calls
vsock/test: fix failures due to wrong SO_RCVLOWAT parameter
net/mlx5e: Remove workaround to avoid syndrome for internal port
net/mlx5e: SD, Use correct mdev to build channel param
net/mlx5: E-Switch, Fix switching to switchdev mode in MPV
net/mlx5: E-Switch, Fix switching to switchdev mode with IB device disabled
net/mlx5: HWS: Properly set bwc queue locks lock classes
net/mlx5: HWS: Fix memory leak in mlx5hws_definer_calc_layout
bnxt_en: handle tpa_info in queue API implementation
bnxt_en: refactor bnxt_alloc_rx_rings() to call bnxt_alloc_rx_agg_bmap()
bnxt_en: refactor tpa_info alloc/free into helpers
geneve: do not assume mac header is set in geneve_xmit_skb()
mlxsw: spectrum_acl_flex_keys: Use correct key block on Spectrum-4
ethtool: Fix wrong mod state in case of verbose and no_mask bitset
ipmr: tune the ipmr_can_free_table() checks.
netfilter: nft_set_hash: skip duplicated elements pending gc run
netfilter: ipset: Hold module reference while requesting a module
...
The current requested response version(V1) for MANA_QUERY_GF_STAT query
results in STATISTICS_FLAGS_TX_ERRORS_GDMA_ERROR value being set to
0 always.
In order to get the correct value for this counter we request the response
version to be V2.
Cc: stable@vger.kernel.org
Fixes: e1df5202e8 ("net :mana :Add remaining GDMA stats for MANA to ethtool")
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/1733291300-12593-1-git-send-email-shradhagupta@linux.microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce new scheduling elements in the E-Switch QoS hierarchy to
enhance traffic management capabilities. This patch adds support for:
- Rate Limit scheduling elements: Enables bandwidth limitation across
multiple nodes without a shared ancestor, providing a mechanism for
more granular control of bandwidth allocation.
- Traffic Class Transmit Scheduling Arbiter (TSAR): Introduces the
infrastructure for creating Traffic Class TSARs, allowing
hierarchical arbitration based on traffic classes.
- Traffic Class Arbiter TSAR: Adds support for a TSAR capable of
managing arbitration between multiple traffic classes, enabling
improved bandwidth prioritization and traffic management.
No functional changes are introduced in this patch.
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241204220931.254964-4-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In the original flow, the crystal_cap might be calculated as a negative
value and set as an overflow value. Therefore, we added a check to limit
the calculated crystal_cap value. Additionally, we shrank the crystal_cap
adjustment according to specific CFO.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241128055433.11851-7-pkshih@realtek.com
The original handling will iterate all active links under the given sta
and apply the changes to each. Now, stack tweaks ops from sta_rc_update
to link_sta_rc_update, which means targeting a given link. Then, our link
iteration looks redundant. So, refine it to apply the changes to the link
directly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241128055433.11851-6-pkshih@realtek.com
The PPDU status of probe response will fail to parse the IE due to being
filtered by the to_self check. Therefore, we parse RSSI from PHY report in
RX descriptor.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241128055433.11851-5-pkshih@realtek.com
Declare beacon filter and connection monitor for 8852BT.
This offloads connection monitor mechanism to firmware, and this
is required for the MCC feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241128055433.11851-4-pkshih@realtek.com
Declare beacon filter and connection monitor for 8852B.
This offloads connection monitor mechanism to firmware, and this
is required for the MCC feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241128055433.11851-3-pkshih@realtek.com
Extend the bitfield for duration in channel info to 16 bits.
Update the related format in H2C and C2H, then increase firmware
format sequence to 3.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241128055433.11851-2-pkshih@realtek.com
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-12-03 (ice, idpf, ixgbe, ixgbevf, igb)
This series contains updates to ice, idpf, ixgbe, ixgbevf, and igb
drivers.
For ice:
Arkadiusz corrects search for determining whether PHY clock recovery is
supported on the device.
Przemyslaw corrects mask used for PHY timestamps on ETH56G devices.
Wojciech adds missing virtchnl ops which caused NULL pointer
dereference.
Marcin fixes VLAN filter settings for uplink VSI in switchdev mode.
For idpf:
Josh restores setting of completion tag for empty buffers.
For ixgbevf:
Jake removes incorrect initialization/support of IPSEC for mailbox
version 1.5.
For ixgbe:
Jake rewords and downgrades misleading message when negotiation
of VF mailbox version is not supported.
Tore Amundsen corrects value for BASE-BX10 capability.
For igb:
Yuan Can adds proper teardown on failed pci_register_driver() call.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igb: Fix potential invalid memory access in igb_init_module()
ixgbe: Correct BASE-BX10 compliance code
ixgbe: downgrade logging of unsupported VF API version to debug
ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5
idpf: set completion tag for "empty" bufs associated with a packet
ice: Fix VLAN pruning in switchdev mode
ice: Fix NULL pointer dereference in switchdev
ice: fix PHY timestamp extraction for ETH56G
ice: fix PHY Clock Recovery availability check
====================
Link: https://patch.msgid.link/20241203215521.1646668-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new member visible to simplify setting the static visibility.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/dba77e76-be45-4a30-96c7-45e284072ad2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously a workaround was added to avoid syndrome 0xcdb051. It is
triggered when offload a rule with tunnel encapsulation, and
forwarding to another table, but not matching on the internal port in
firmware steering mode. The original workaround skips internal tunnel
port logic, which is not correct as not all cases are considered. As
an example, if vlan is configured on the uplink port, traffic can't
pass because vlan header is not added with this workaround. Besides,
there is no such issue for software steering. So, this patch removes
that, and returns error directly if trying to offload such rule for
firmware steering.
Fixes: 06b4eac9c4 ("net/mlx5e: Don't offload internal port if filter device is out device")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Tested-by: Frode Nordahl <frode.nordahl@canonical.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a multi-PF netdev, each traffic channel creates its own resources
against a specific PF.
In the cited commit, where this support was added, the channel_param
logic was mistakenly kept unchanged, so it always used the primary PF
which is found at priv->mdev.
In this patch we fix this by moving the logic to be per-channel, and
passing the correct mdev instance.
This bug happened to be usually harmless, as the resulting cparam
structures would be the same for all channels, due to identical FW logic
and decisions.
However, in some use cases, like fwreset, this gets broken.
This could lead to different symptoms. Example:
Error cqe on cqn 0x428, ci 0x0, qn 0x10a9, opcode 0xe, syndrome 0x4,
vendor syndrome 0x32
Fixes: e4f9686bde ("net/mlx5e: Let channels be SD-aware")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the mentioned commit change for MPV mode, since in MPV mode the IB
device is shared between different core devices, so under this change
when moving both devices simultaneously to switchdev mode the IB device
removal and re-addition can race with itself causing unexpected behavior.
In such case do rescan_drivers() only once in order to add the ethernet
representor auxiliary device, and skip adding and removing IB devices.
Fixes: ab85ebf437 ("net/mlx5: E-switch, refactor eswitch mode change")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case that IB device is already disabled when moving to switchdev mode,
which can happen when working with LAG, need to do rescan_drivers()
before leaving in order to add ethernet representor auxiliary device.
Fixes: ab85ebf437 ("net/mlx5: E-switch, refactor eswitch mode change")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It allocates a match template, which creates a compressed definer fc
struct, but that is not deallocated.
This commit fixes that.
Fixes: 74a778b4a6 ("net/mlx5: HWS, added definers handling")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241203204920.232744-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 7ed816be35 ("eth: bnxt: use page pool for head frags") added a
page pool for header frags, which may be distinct from the existing pool
for the aggregation ring. Prior to this change, frags used in the TPA
ring rx_tpa were allocated from system memory e.g. napi_alloc_frag()
meaning their lifetimes were not associated with a page pool. They can
be returned at any time and so the queue API did not alloc or free
rx_tpa.
But now frags come from a separate head_pool which may be different to
page_pool. Without allocating and freeing rx_tpa, frags allocated from
the old head_pool may be returned to a different new head_pool which
causes a mismatch between the pp hold/release count.
Fix this problem by properly freeing and allocating rx_tpa in the queue
API implementation.
Signed-off-by: David Wei <dw@davidwei.uk>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241204041022.56512-4-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor bnxt_rx_ring_info->tpa_info operations into helpers that work
on a single tpa_info in prep for queue API using them.
There are 2 pairs of operations:
* bnxt_alloc_one_tpa_info()
* bnxt_free_one_tpa_info()
These alloc/free the tpa_info array itself.
* bnxt_alloc_one_tpa_info_data()
* bnxt_free_one_tpa_info_data()
These alloc/free the frags stored in tpa_info array.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: David Wei <dw@davidwei.uk>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241204041022.56512-2-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove phylink_phy_no_inband() now that we are handling the lack of
inband negotiation by querying the capabilities of the PHY and PCS,
and the BCM84881 PHY driver provides us the information necessary to
make the decision.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUsO-006IUt-KN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support for in-band signalling with Serdes links is uncertain. Some
PHYs do not support in-band for e.g. SGMII. Some PCS do not support
in-band for 2500Base-X. Some PCS require in-band for Base-X protocols.
Simply using what is in DT is insufficient when we have hot-pluggable
PHYs e.g. in the form of SFP modules, which may not provide the
in-band signalling.
In order to address this, we have introduced phy_inband_caps() and
pcs_inband_caps() functions to allow phylink to retrieve the
capabilities from each end of the PCS/PHY link. This commit adds code
to resolve whether in-band will be used in the various scenarios that
we have: In-band not being used, PHY present using SGMII or Base-X,
PHY not present. We also deal with no capabilties provided.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUsJ-006IUn-H3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report the PCS in-band capabilities to phylink for Marvell PP2
interfaces.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUsE-006IUh-E7@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report the PCS in-band capabilities to phylink for Marvell NETA
interfaces.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUs9-006IUb-Au@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a pcs_inband_caps() method to query the PCS for its inband link
capabilities, and use this to determine whether link modes used with
optical SFPs can be supported.
When a PCS does not provide a method, we allow inband negotiation to
be either on or off, making this a no-op until the pcs_inband_caps()
method is implemented by a PCS driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUs4-006IUU-7K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the config_inband() method for Marvell 88E1112, 88E1111,
and Finisar's 88E1111 variant.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUrz-006IUO-3r@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a method to configure the PHY's in-band mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUru-006IUI-08@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide an implementation for phy_inband_caps() for Marvell PHYs used
on SFP modules, so that phylink knows the PHYs capabilities.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUro-006IUC-Rq@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM84881 has no support for inband signalling, so this is a trivial
implementation that returns no support for inband.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/E1tIUrj-006IU6-ON@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a method to query the PHY's in-band capabilities for a PHY
interface mode.
Where the interface mode does not have in-band capability, or the PHY
driver has not been updated to return this information, then
phy_inband_caps() should return zero. Otherwise, PHY drivers will
return a value consisting of the following flags:
LINK_INBAND_DISABLE indicates that the hardware does not support
in-band signalling, or can have in-band signalling configured via
software to be disabled.
LINK_INBAND_ENABLE indicates that the hardware will use in-band
signalling, or can have in-band signalling configured via software
to be enabled.
LINK_INBAND_BYPASS indicates that the hardware has the ability to
bypass in-band signalling when enabled after a timeout if the link
partner does not respond to its in-band signalling.
This reports the PHY capabilities for the particular interface mode,
not the current configuration.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUre-006ITz-KF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that we have a more complexity in phylink_major_config(), augment
the debugging so we can see what's going on there.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUrZ-006ITt-Fa@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an interdependence between the current link_an_mode and
pcs_neg_mode that some drivers rely upon to know whether inband or PHY
mode will be used.
In order to support detection of PCS and PHY inband capabilities
resulting in automatic selection of inband or PHY mode, we need to
cater for this, and support changing the MAC link_an_mode. However, we
end up with an inter-dependency between the current link_an_mode and
pcs_neg_mode.
To solve this, split the current link_an_mode into the requested
link_an_mode and active link_an_mode. The requested link_an_mode will
always be passed to phylink_pcs_neg_mode(), and the active link_an_mode
will be used for everything else, and only updated during
phylink_major_config(). This will ensure that phylink_pcs_neg_mode()'s
link_an_mode will not depend on the active link_an_mode that will,
in a future patch, depend on pcs_neg_mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUrU-006ITn-Ai@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the call to phylink_pcs_neg_mode() in phylink_major_config() after
we have selected the appropriate PCS to allow the PCS to be passed in.
Add struct phylink and struct phylink_pcs pointers to
phylink_pcs_neg_mode() and pass in the appropriate structures. Set
pl->pcs_neg_mode before returning, and remove the return value.
This will allow the capabilities of the PCS and any PHY to be used when
deciding which pcs_neg_mode should be used.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tIUrP-006ITh-6u@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver is currently using an ACL key block that is not supported by
Spectrum-4. This works because the driver is only using a single field
from this key block which is located in the same offset in the
equivalent Spectrum-4 key block.
The issue was discovered when the firmware started rejecting the use of
the unsupported key block. The change has been reverted to avoid
breaking users that only update their firmware.
Nonetheless, fix the issue by using the correct key block.
Fixes: 07ff135958 ("mlxsw: Introduce flex key elements for Spectrum-4")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/35e72c97bdd3bc414fb8e4d747e5fb5d26c29658.1733237440.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enhance observability of netconsole. Packet sends can fail.
Start tracking at least two failure possibilities: ENOMEM and
NET_XMIT_DROP for every target. Stats are exposed via an additional
attribute in CONFIGFS.
The exposed statistics allows easier debugging of cases when netconsole
messages were not seen by receivers, eliminating the guesswork if the
sender thinks that messages in question were sent out.
Stats are not reset on enable/disable/change remote ip/etc, they
belong to the netcons target itself.
Reported-by: Breno Leitao <leitao@debian.org>
Closes: https://lore.kernel.org/all/ZsWoUzyK5du9Ffl+@gmail.com/
Signed-off-by: Maksym Kutsevol <max@kutsevol.com>
Link: https://patch.msgid.link/20241202-netcons-add-udp-send-fail-statistics-to-netconsole-v5-2-70e82239f922@kutsevol.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ML interfaces can have multiple affiliated links to it and
hence there is a need to report tx power of specified link
rather deflink.
Add changes to report tx power of requested link from mac80211,
also pass link id as an argument in get_tx_power op so that supported
drivers can use it to report link's tx power.
Co-developed-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20241125083217.216095-3-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, TX power is reported on interface/wdev level as
part of NL80211_CMD_GET_INTERFACE. With MLO, Multiple links
can be part of an interface/wdev and hence its necessary to
report the TX power of each link.
Add support to send tx power for all valid links of an MLD as
part of NL80211_CMD_GET_INTERFACE request.
As far as userspace is concerned, there is no behavioral change
for Non-ML Interfaces. For ML interfaces, userspace should fetch
TX power that is nested inside NL80211_ATTR_MLO_LINKS, similar to
how channel info(NL80211_ATTR_WIPHY_FREQ) is fetched.
Co-developed-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20241125083217.216095-2-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch replaces spaces with tabs in the affected source files to
adhere to the Linux kernel coding style guidelines.
This change is purely stylistic and do not affect the functionality
of the code.
Signed-off-by: Juan José Arboleda <soyjuanarbol@gmail.com>
Link: https://patch.msgid.link/715c74c74b336bed81e92e1336bd1a6ddb7b90ff.1724103043.git.soyjuanarbol@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a follow-up to 982300c115 ("r8169: remove detection of chip
version 11 (early RTL8168b)"). Nobody complained yet, so remove
support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/b689ab6d-20b5-4b64-bd7e-531a0a972ba3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After 854d71c555 ("r8169: remove original workaround for RTL8125
broken rx issue") this flag isn't used any longer. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/d9dd214b-3027-4f60-b0e8-6f34a0c76582@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The pci_register_driver() can fail and when this happened, the dca_notifier
needs to be unregistered, otherwise the dca_notifier can be called when
igb fails to install, resulting to invalid memory access.
Fixes: bbd98fe48a ("igb: Fix DCA errors and do not use context index for 82576")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
SFF-8472 (section 5.4 Transceiver Compliance Codes) defines bit 6 as
BASE-BX10. Bit 6 means a value of 0x40 (decimal 64).
The current value in the source code is 0x64, which appears to be a
mix-up of hex and decimal values. A value of 0x64 (binary 01100100)
incorrectly sets bit 2 (1000BASE-CX) and bit 5 (100BASE-FX) as well.
Fixes: 1b43e0d20f ("ixgbe: Add 1000BASE-BX support")
Signed-off-by: Tore Amundsen <tore@amundsen.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Ernesto Castellotti <ernesto@castellotti.net>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ixgbe PF driver logs an info message when a VF attempts to negotiate an
API version which it does not support:
VF 0 requested invalid api version 6
The ixgbevf driver attempts to load with mailbox API v1.5, which is
required for best compatibility with other hosts such as the ESX VMWare PF.
The Linux PF only supports API v1.4, and does not currently have support
for the v1.5 API.
The logged message can confuse users, as the v1.5 API is valid, but just
happens to not currently be supported by the Linux PF.
Downgrade the info message to a debug message, and fix the language to
use 'unsupported' instead of 'invalid' to improve message clarity.
Long term, we should investigate whether the improvements in the v1.5 API
make sense for the Linux PF, and if so implement them properly. This may
require yet another API version to resolve issues with negotiating IPSEC
offload support.
Fixes: 339f289641 ("ixgbevf: Add support for new mailbox communication between PF and VF")
Reported-by: Yifei Liu <yifei.l.liu@oracle.com>
Link: https://lore.kernel.org/intel-wired-lan/20240301235837.3741422-1-yifei.l.liu@oracle.com/
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 339f289641 ("ixgbevf: Add support for new mailbox communication
between PF and VF") added support for v1.5 of the PF to VF mailbox
communication API. This commit mistakenly enabled IPSEC offload for API
v1.5.
No implementation of the v1.5 API has support for IPSEC offload. This
offload is only supported by the Linux PF as mailbox API v1.4. In fact, the
v1.5 API is not implemented in any Linux PF.
Attempting to enable IPSEC offload on a PF which supports v1.5 API will not
work. Only the Linux upstream ixgbe and ixgbevf support IPSEC offload, and
only as part of the v1.4 API.
Fix the ixgbevf Linux driver to stop attempting IPSEC offload when
the mailbox API does not support it.
The existing API design choice makes it difficult to support future API
versions, as other non-Linux hosts do not implement IPSEC offload. If we
add support for v1.5 to the Linux PF, then we lose support for IPSEC
offload.
A full solution likely requires a new mailbox API with a proper negotiation
to check that IPSEC is actually supported by the host.
Fixes: 339f289641 ("ixgbevf: Add support for new mailbox communication between PF and VF")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit d9028db618 ("idpf: convert to libeth Tx buffer completion")
inadvertently removed code that was necessary for the tx buffer cleaning
routine to iterate over all buffers associated with a packet.
When a frag is too large for a single data descriptor, it will be split
across multiple data descriptors. This means the frag will span multiple
buffers in the buffer ring in order to keep the descriptor and buffer
ring indexes aligned. The buffer entries in the ring are technically
empty and no cleaning actions need to be performed. These empty buffers
can precede other frags associated with the same packet. I.e. a single
packet on the buffer ring can look like:
buf[0]=skb0.frag0
buf[1]=skb0.frag1
buf[2]=empty
buf[3]=skb0.frag2
The cleaning routine iterates through these buffers based on a matching
completion tag. If the completion tag is not set for buf2, the loop will
end prematurely. Frag2 will be left uncleaned and next_to_clean will be
left pointing to the end of packet, which will break the cleaning logic
for subsequent cleans. This consequently leads to tx timeouts.
Assign the empty bufs the same completion tag for the packet to ensure
the cleaning routine iterates over all of the buffers associated with
the packet.
Fixes: d9028db618 ("idpf: convert to libeth Tx buffer completion")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Madhu chittim <madhu.chittim@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In switchdev mode the uplink VSI should receive all unmatched packets,
including VLANs. Therefore, VLAN pruning should be disabled if uplink is
in switchdev mode. It is already being done in ice_eswitch_setup_env(),
however the addition of ice_up() in commit 44ba608db5 ("ice: do
switchdev slow-path Rx using PF VSI") caused VLAN pruning to be
re-enabled after disabling it.
Add a check to ice_set_vlan_filtering_features() to ensure VLAN
filtering will not be enabled if uplink is in switchdev mode. Note that
ice_is_eswitch_mode_switchdev() is being used instead of
ice_is_switchdev_running(), as the latter would only return true after
the whole switchdev setup completes.
Fixes: 44ba608db5 ("ice: do switchdev slow-path Rx using PF VSI")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To check if PHY Clock Recovery mechanic is available for a device, there
is a need to verify if given PHY is available within the netlist, but the
netlist node type used for the search is wrong, also the search context
shall be specified.
Modify the search function to allow specifying the context in the
search.
Use the PHY node type instead of CLOCK CONTROLLER type, also use proper
search context which for PHY search is PORT, as defined in E810
Datasheet [1] ('3.3.8.2.4 Node Part Number and Node Options (0x0003)' and
'Table 3-105. Program Topology Device NVM Admin Command').
[1] https://cdrdv2.intel.com/v1/dl/getContent/613875?explicitVersion=true
Fixes: 91e43ca009 ("ice: fix linking when CONFIG_PTP_1588_CLOCK=n")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently rtnl_link_get_net_ifla() gets called twice when we create
peer devices, once in rtnl_add_peer_net() and once in each ->newlink()
implementation.
This looks safer, however, it leads to a classic Time-of-Check to
Time-of-Use (TOCTOU) bug since IFLA_NET_NS_PID is very dynamic. And
because of the lack of checking error pointer of the second call, it
also leads to a kernel crash as reported by syzbot.
Fix this by getting rid of the second call, which already becomes
redudant after Kuniyuki's work. We have to propagate the result of the
first rtnl_link_get_net_ifla() down to each ->newlink().
Reported-by: syzbot+21ba4d5adff0b6a7cfc6@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=21ba4d5adff0b6a7cfc6
Fixes: 0eb87b02a7 ("veth: Set VETH_INFO_PEER to veth_link_ops.peer_type.")
Fixes: 6b84e558e9 ("vxcan: Set VXCAN_INFO_PEER to vxcan_link_ops.peer_type.")
Fixes: fefd5d0821 ("netkit: Set IFLA_NETKIT_PEER_INFO to netkit_link_ops.peer_type.")
Cc: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241129212519.825567-1-xiyou.wangcong@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If we got an unprotected action frame with CSA and then we heard the
beacon with the CSA IE, we'll block the queues with the CSA reason
twice. Since this reason is refcounted, we won't wake up the queues
since we wake them up only once and the ref count will never reach 0.
This led to blocked queues that prevented any activity (even
disconnection wouldn't reset the queue state and the only way to recover
would be to reload the kernel module.
Fix this by not refcounting the CSA reason.
It becomes now pointless to maintain the csa_blocked_queues state.
Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 414e090bc4 ("wifi: mac80211: restrict public action ECSA frame handling")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219447
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241119173108.5ea90828c2cc.I4f89e58572fb71ae48e47a81e74595cac410fbac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 43645ce03e ("qed: Populate nvm image attribute shadow.")
added support for populating flash image attributes, notably
"num_images". However, some cards were not able to return this
information. In such cases, the driver would return EINVAL, causing the
driver to exit.
Add check to return EOPNOTSUPP instead of EINVAL when the card is not
able to return these information. The caller function already handles
EOPNOTSUPP without error.
Fixes: 43645ce03e ("qed: Populate nvm image attribute shadow.")
Co-developed-by: Florian Forestier <florian@forestier.re>
Signed-off-by: Florian Forestier <florian@forestier.re>
Signed-off-by: Louis Leseur <louis.leseur@gmail.com>
Link: https://patch.msgid.link/20241128083633.26431-1-louis.leseur@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix outdated MII_LPA data in the LAN88xx PHY, which is used in LAN7800
and LAN7850 USB Ethernet controllers. Due to a hardware limitation, the
PHY cannot reliably update link status after parallel detection when the
link partner does not support auto-negotiation. To mitigate this, add a
PHY reset in `lan88xx_link_change_notify()` when `phydev->state` is
`PHY_NOLINK`, ensuring the PHY starts in a clean state and reports
accurate fixed link parallel detection results.
Fixes: 792aec47d5 ("add microchip LAN88xx phy driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241125084050.414352-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEUEC6huC2BN0pvD5fKDiiPnotvG8FAmdNdZ0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAoOKI+ei28b76fB/9mW1n8e9GEUallIie+f+uGBRi4nMCI
GeyuVZyVMUH1pJBXHMQ4B17ZRJ8ynF0gFZ7evMbwsJ9aJ2ZOQVQWPO6FaAge2jrJ
9HD/LQsj55+YXaCyPnFlpCmH8HvA2ojVvIbpGyz+u9zAwJXI/2hwMVSNBt5HaAg7
iJ2Rij/PECWDD2cR/OU2cDNjZPMyn3HEyZGAEDKlsQZQbZNFfqFdr8MXP76ppjjx
f9PKW9LeaA6L2wyXjx2tTFIABsnJRJSQJenVVH/lQLC6Kqkq3j7Z0umAxQ6fQ9qT
5LvJt6rP+5ZsUEOxkG5mMhsweAaynzFvur+ZVCZpRg2HHL35PQ0UX67/
=ZT7R
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-6.13-20241202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2024-12-02
The first patch is by me and allows the use of sleeping GPIOs to set
termination GPIOs.
Alexander Kozhinov fixes the gs_usb driver to use the endpoints
provided by the usb endpoint descriptions instead of hard coded ones.
Dario Binacchi contributes 11 statistics related patches for various
CAN driver. A potential use after free in the hi311x is fixed. The
statistics for the c_can, sun4i_can, hi311x, m_can, ifi_canfd,
sja1000, sun4i_can, ems_usb, f81604 are fixed: update statistics even
if the allocation of the error skb fails and fix the incrementing of
the rx,tx error counters.
A patch by me fixes the workaround for DS80000789E 6 erratum in the
mcp251xfd driver.
The last patch is by Dmitry Antipov, targets the j1939 CAN protocol
and fixes a skb reference counting issue.
* tag 'linux-can-fixes-for-6.13-20241202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: j1939_session_new(): fix skb reference counting
can: mcp251xfd: mcp251xfd_get_tef_len(): work around erratum DS80000789E 6.
can: f81604: f81604_handle_can_bus_errors(): fix {rx,tx}_errors statistics
can: ems_usb: ems_usb_rx_err(): fix {rx,tx}_errors statistics
can: sun4i_can: sun4i_can_err(): fix {rx,tx}_errors statistics
can: sja1000: sja1000_err(): fix {rx,tx}_errors statistics
can: hi311x: hi3110_can_ist(): fix {rx,tx}_errors statistics
can: ifi_canfd: ifi_canfd_handle_lec_err(): fix {rx,tx}_errors statistics
can: m_can: m_can_handle_lec_err(): fix {rx,tx}_errors statistics
can: hi311x: hi3110_can_ist(): update state error statistics if skb allocation fails
can: hi311x: hi3110_can_ist(): fix potential use-after-free
can: sun4i_can: sun4i_can_err(): call can_change_state() even if cf is NULL
can: c_can: c_can_handle_bus_err(): update statistics if skb allocation fails
can: gs_usb: add usb endpoint address detection at driver probe step
can: dev: can_set_termination(): allow sleeping GPIOs
====================
Link: https://patch.msgid.link/20241202090040.1110280-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current driver allows only packet size < 512B as SDP_LINK_CREDIT
register is set to default value.
This patch fixes this issue by configure the register with
maximum HW supported value to allow packet size > 512B.
Fixes: 2f7f33a095 ("octeontx2-pf: Add representors for sdp MAC")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2f4f9fe5bf ("bnxt_en: Support adding ntuple rules on RSS
contexts") added support for redirecting to an RSS context as an ntuple
rule action. However, it forgot to update the ETHTOOL_GRXCLSRULE
codepath. This caused `ethtool -n` to always report the action as
"Action: Direct to queue 0" which is wrong.
Fix by teaching bnxt driver to report the RSS context when applicable.
Fixes: 2f4f9fe5bf ("bnxt_en: Support adding ntuple rules on RSS contexts")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Link: https://patch.msgid.link/2e884ae39e08dc5123be7c170a6089cefe6a78f7.1732748253.git.dxu@dxuuu.xyz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When hardware device group abstraction is introduced, the QMI firmware ready
event of different devices in a group can be received simultaneously. To
indicate the firmware ready event is completed for a particular device in a
group set a flag (ATH12K_FLAG_QMI_FW_READY_COMPLETE). This helps the upcoming
hardware recovery implementation for hardware device group abstraction.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-5-kvalo@kernel.org
Currently, one or more struct ath12k_hw is part of device (struct ath12k_base)
but in future, ath12k_hw would be part of device group (struct
ath12k_hw_group). Hence, num_hw under device would be moved to device group.
To facilitate above transition, add helper ath12k_get_num_hw() to get the
number of radios per device. In future, this helper will return the number of
radios in a device group.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-4-kvalo@kernel.org
Currently, one or more ath12k_hw is part of a device (struct ath12k_base) but
in future, it would be part of device group abstraction (struct
ath12k_hw_group), i.e., when multiple radios (ar) across different devices can
be combined together in a device group (struct ath12k_hw_group).
In order to facilitate the above transition, introduce helpers
ath12k_ab_to_ah() and ath12k_ab_set_ah() to get and set values of ath12k_hw
respectively.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-3-kvalo@kernel.org
In the upcoming hardware device group abstraction radios across different
devices can be grouped together to support multi-link operation and register as
a device group to mac80211.
Currently, ath12k_mac_allocate() and ath12k_mac_register() are part of
ath12k_core_start() and ath12k_core_pdev_create() respectively and are based on
per device (struct ath12k_base). These APIs can be decoupled and moved out to
ath12k_core_qmi_firmware_ready() itself. This refactor is helpful for device
group abstraction when mac80211 allocate and register will be changed from per
device (struct ath12k_base) to per device group (struct ath12k_hw_group).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-2-kvalo@kernel.org
Both ENETC PF and VF drivers share enetc_setup_tc_mqprio() to configure
MQPRIO. And enetc_setup_tc_mqprio() calls enetc_change_preemptible_tcs()
to configure preemptible TCs. However, only PF is able to configure
preemptible TCs. Because only PF has related registers, while VF does not
have these registers. So for VF, its hw->port pointer is NULL. Therefore,
VF will access an invalid pointer when accessing a non-existent register,
which will cause a crash issue. The simplified log is as follows.
root@ls1028ardb:~# tc qdisc add dev eno0vf0 parent root handle 100: \
mqprio num_tc 4 map 0 0 1 1 2 2 3 3 queues 1@0 1@1 1@2 1@3 hw 1
[ 187.290775] Unable to handle kernel paging request at virtual address 0000000000001f00
[ 187.424831] pc : enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.430518] lr : enetc_mm_commit_preemptible_tcs+0x30c/0x400
[ 187.511140] Call trace:
[ 187.513588] enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.518918] enetc_setup_tc_mqprio+0x180/0x214
[ 187.523374] enetc_vf_setup_tc+0x1c/0x30
[ 187.527306] mqprio_enable_offload+0x144/0x178
[ 187.531766] mqprio_init+0x3ec/0x668
[ 187.535351] qdisc_create+0x15c/0x488
[ 187.539023] tc_modify_qdisc+0x398/0x73c
[ 187.542958] rtnetlink_rcv_msg+0x128/0x378
[ 187.547064] netlink_rcv_skb+0x60/0x130
[ 187.550910] rtnetlink_rcv+0x18/0x24
[ 187.554492] netlink_unicast+0x300/0x36c
[ 187.558425] netlink_sendmsg+0x1a8/0x420
[ 187.606759] ---[ end trace 0000000000000000 ]---
In addition, some PFs also do not support configuring preemptible TCs,
such as eno1 and eno3 on LS1028A. It won't crash like it does for VFs,
but we should prevent these PFs from accessing these unimplemented
registers.
Fixes: 827145392a ("net: enetc: only commit preemptible TCs to hardware when MM TX is active")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring TSN (Qbv, Qbu, PSFP) capabilities requires access to port
registers, which are available to the PSI but not the VSI.
Yet, the SI port capability register 0 (PSICAPR0), exposed to both PSIs
and VSIs, presents the same capabilities to the VF as to the PF, thus
leading the VF driver into thinking it can configure these features.
In the case of ENETC_SI_F_QBU, having it set in the VF leads to a crash:
root@ls1028ardb:~# tc qdisc add dev eno0vf0 parent root handle 100: \
mqprio num_tc 4 map 0 0 1 1 2 2 3 3 queues 1@0 1@1 1@2 1@3 hw 1
[ 187.290775] Unable to handle kernel paging request at virtual address 0000000000001f00
[ 187.424831] pc : enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.430518] lr : enetc_mm_commit_preemptible_tcs+0x30c/0x400
[ 187.511140] Call trace:
[ 187.513588] enetc_mm_commit_preemptible_tcs+0x1c4/0x400
[ 187.518918] enetc_setup_tc_mqprio+0x180/0x214
[ 187.523374] enetc_vf_setup_tc+0x1c/0x30
[ 187.527306] mqprio_enable_offload+0x144/0x178
[ 187.531766] mqprio_init+0x3ec/0x668
[ 187.535351] qdisc_create+0x15c/0x488
[ 187.539023] tc_modify_qdisc+0x398/0x73c
[ 187.542958] rtnetlink_rcv_msg+0x128/0x378
[ 187.547064] netlink_rcv_skb+0x60/0x130
[ 187.550910] rtnetlink_rcv+0x18/0x24
[ 187.554492] netlink_unicast+0x300/0x36c
[ 187.558425] netlink_sendmsg+0x1a8/0x420
[ 187.606759] ---[ end trace 0000000000000000 ]---
while the other TSN features in the VF are harmless, because the
net_device_ops used for the VF driver do not expose entry points for
these other features.
These capability bits are in the process of being defeatured from the SI
registers. We should read them from the port capability register, where
they are also present, and which is naturally only exposed to the PF.
The change to blame (relevant for stable backports) is the one where
this started being a problem, aka when the kernel started to crash due
to the wrong capability seen by the VF driver.
Fixes: 827145392a ("net: enetc: only commit preemptible TCs to hardware when MM TX is active")
Reported-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a todo comment to use mac80211 provided link id. As mac80211 now
provides it use it in ath12k and remove the comment.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-11-kvalo@kernel.org
Dan reported that in some cases the ret variable could be uninitialized. Fix
that by removing the out label entirely and returning zero explicitly on
succesful cases.
Also remove the unnecessary else branches to follow more the style used in
ath12k and now it's easier to see the error handling.
No functional changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/7e7afd00-ad84-4744-8d94-416bab7e7dd9@stanley.mountain/
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-10-kvalo@kernel.org
Currently for single radio devices (ah->num_radio == 1)
ath12k_mac_op_add_interface() creates vdev and later hw scan and
assign_vif_chanctx uses the same. For MLO, vdev create request should carry ML
address which will not be known during ath12k_mac_op_add_interface() as vif
will be marked as ML only after links are added to it.
If hw scan is requested, the vdev will be deleted post hw scan and subsequent
assign_vif_chanctx call will create new vdev with ML address. But in certain
cases assign_vif_chanctx could be called without any prior hw scan request and
reusing the previously created vdev causes a non-ML vdev to be used for an ML
vif and firmware operates the vdev in non-ML mode.
Fix this by deferring vdev creation for interface until hw scan or
assign_vif_chanctx request is received from mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-9-kvalo@kernel.org
Currently, the ath12k_bss_assoc() function handles only deflink station
connections. To support multi-link station connections, make the necessary
changes to retrieve the required information from the link-level members.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-8-kvalo@kernel.org
When a scan request is received, driver selects a link id for which the arvif
can be mapped. Same link is also used for getting the link conf address.
Currently, we return 0 as link id for a non ML vif, which is correct since that
is the default link id. Also when any of the link vif is active and the scan
request is for a channel in the active link we return its link id. But, when we
don't hit both of the above cases (i.e not a ML vif or no active link vif for
the channel is present) we currently return 0 as the link id.
Bu the problemis that this might not work out always, eg., when only one link
(eg. linkid = 1) is added to vif, then we won't find any link conf for link id
0 in the vif resulting in scan failure. During AP bringup, such scan failure
causes bringup issues. Hence avoid sending link id 0 as default. Rather use a
default link for scan and default link address for the same. This scan vdev
will either be deleted if another scan is requested on same vif or when AP is
broughtup on same link or during interface cleanup.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-7-kvalo@kernel.org
If peer creation fails ar->rx_stats needs to be freed in error handling.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-6-kvalo@kernel.org
Apply tid queue setup based on all link stations on receiving ampdu action
params for an ML Station.
Modify ath12k_get_ar_by_vif() to fetch ar based on link arvif inside ahvif.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-5-kvalo@kernel.org
Currently when tx flush is requested for an vif only packets corresponding to
deflink are flushed, with MLO multiple link arvif could be affiliated to the ML
vif and packets corresponding to all of them should be flushed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-4-kvalo@kernel.org
For a frame transmission for an ML vif, mac80211 mentions transmit link id in
the tx control info. Use it to convert the RA/TA to the corresponding link sta
and link vif address before enqueueing the frame for transmission.
For 802.3 data frames, always enqueue the frame on the primary (assoc) link id.
Firmware does the link selection, builds 802.11 header and therefore the address
translation too.
Also ensure right link vif is used for WMI based management transmission and
add comments to document when RCU read lock is held.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-3-kvalo@kernel.org
To simplify locking for the next patches convert struct
ath12k::wmi_mgmt_tx_work to use wiphy_work. After this
ath12k_mgmt_over_wmi_tx_work() is called with wiphy_lock() taken. In
ath12k_core_suspend() we need to take wiphy_lock() because
ath12k_mac_wait_tx_complete() requires it.
Also add lockdep_assert_wiphy() to document when wiphy_lock() is held.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-2-kvalo@kernel.org
When phy_ethtool_set_eee_noneg() detects a change in the LPI
parameters, it attempts to update phylib state and trigger the link
to cycle so the MAC sees the updated parameters.
However, in doing so, it sets phydev->enable_tx_lpi depending on
whether the EEE configuration allows the MAC to generate LPI without
taking into account the result of negotiation.
This can be demonstrated with a 1000base-T FD interface by:
# ethtool --set-eee eno0 advertise 8 # cause EEE to be not negotiated
# ethtool --set-eee eno0 tx-lpi off
# ethtool --set-eee eno0 tx-lpi on
This results in being true, despite EEE not having been negotiated and:
# ethtool --show-eee eno0
EEE status: enabled - inactive
Tx LPI: 250 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Fix this by keeping track of whether EEE was negotiated via a new
eee_active member in struct phy_device, and include this state in
the decision whether phydev->enable_tx_lpi should be set.
Fixes: 3e43b903da ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tErSe-005RhB-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In MLD connection, a pairwise key should work on all active links. And, we
take just one entry in security CAM for one pairwise key. (It means we will
reuse one single entry for all links.) Originally, we already applied the
security CAM entry of pairwise key to deflink's address CAM.
However, links can be activated dynamically. So now for pairwise keys, each
rtw89_sta records the IDs of the security CAM entries. Then, when driver is
notified that some links are active via change_sta_links(), we apply target
pairwise keys to them according to the record.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241120034054.13575-5-pkshih@realtek.com
To support MLO, implement change_vif_links() and change_sta_links() ops.
Basically, we follow arguments to set/clear links. One special thing is
that when vif is idle, i.e. no connection, link id 0 is set up by us for
default uses. So, when bitmap of vif links change from 0x0 to non-zero,
we clear the default one first. And when bitmap of vif links change from
non-zero to 0x0, we set up a default one at the end.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241120034054.13575-4-pkshih@realtek.com
Register mac80211 ops of can_activate_links which is required when
we are ready to enable multiple active links.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241120034054.13575-3-pkshih@realtek.com
After FW v0.35.46.0, for AP mode, RTL8922A FW supports a new FW feature,
called NOTIFY_AP_INFO, to notify driver information related to AP mode.
And, one function of it is to monitor PS states of remote stations. Once
one of them changes, FW will send a C2H event to tell driver. With this
FW feature, we can declare AP_LINK_PS.
For now, driver still needs to determine if a frame is ps-poll or U-APSD
trigger. So, add the corresponding RX handling in driver, which activates
only when at least one AP is running.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241120034054.13575-2-pkshih@realtek.com
-----BEGIN PGP SIGNATURE-----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=2Otz
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
callers can't stop a device multiple times, even as we migrate from
the global pci_rescan_remove_lock to finer-grained locking (Keith
Busch)
- Improve pci_walk_bus() implementation by making it recursive and
moving locking up to avoid need for a 'locked' parameter (Keith
Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by
the PCI core (Keith Busch)
- Detect some Thunderbolt chips that are built-in and hence
'trustworthy' by a heuristic since the 'ExternalFacingPort' and
'usb4-host-interface' ACPI properties are not quite enough (Esther
Shimanovich)
Resource management:
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties
when building dynamic DT nodes so systems where PCI and CPU
addresses differ work correctly (Andrea della Porta)
- Tidy resource sizing and assignment with helpers to reduce
redundancy (Ilpo Järvinen)
- Improve pdev_sort_resources() 'bogus alignment' warning to be more
specific (Ilpo Järvinen)
Driver binding:
- Convert driver .remove_new() callbacks to .remove() again to finish
the conversion from returning 'int' to being 'void' (Sergio
Paracuellos)
- Export pcim_request_all_regions(), a managed interface to request
all BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with
pcim_request_all_regions(), and pcim_iomap_table()[n] with
pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
(Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp
Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and
release a PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
cavium (Philipp Stanner)
Error handling:
- Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
bridge; previously Secondary Bus Reset could only be used when
there was a single device below a bridge (Keith Busch)
- Warn if we reset a running device where the driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
ASPM:
- Disable ASPM L1 before touching L1 PM Substates to follow the spec
closer and avoid a CPU load timeout on some platforms (Ajay
Agarwal)
- Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
as required per spec for all L1 Substates changes (Jian-Hong Pan)
Power management:
- Enable starfive controller runtime PM before probing host bridge
(Mayank Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
Power control:
- Use of_platform_device_create() instead of of_platform_populate()
to create pwrctl platform devices so we can control it based on the
child nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power
supply property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure
pwrctl drivers are probed before the PCI dev driver; this avoids a
race where pwrctl could change device power state while the PCI
driver was active (Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node()
instead of searching all children of the parent (Manivannan
Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
('bwctrl') and hotplug files (Bjorn Helgaas)
Bandwidth control:
- Add read/modify/write locking for Link Control 2, which is used to
manage Link speed (Ilpo Järvinen)
- Extract Link Bandwidth Management Status check into
pcie_lbms_seen(), where it can be shared between the bandwidth
controller and quirks that use it to help retrain failed links
(Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address
the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
Järvinen)
- Add pcie_set_target_speed() and related functionality so drivers
can manage PCIe Link speed based on thermal or other constraints
(Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the
existing thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
PCI device hotplug:
- Add hotplug controller driver for Marvell OCTEON multi-function
device where function 0 has a management console interface to
enable/disable and provision various personalities for the other
functions (Shijith Thotton)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to
avoid a use-after-free when the thunderbolt driver resets USB4 host
routers on boot, causing hotplug remove/add of downstream docks or
other devices (Lukas Wunner)
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
detection in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and
doesn't handle devices below hot-added bridges (Ilpo Järvinen)
Virtualization:
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
capability but do isolate functions as though PCI_ACS_RR and
PCI_ACS_CR were set, so the functions can be in independent IOMMU
groups (Mengyuan Lou)
TLP Processing Hints (TPH):
- Add and document TLP Processing Hints (TPH) support so drivers can
enable and disable TPH and the kernel can save/restore TPH
configuration (Wei Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag
values associated with specific CPUs via an ACPI _DSM to improve
performance by directing DMA writes closer to their consumers (Wei
Huang)
Data Object Exchange (DOE):
- Wait up to 1 second for DOE Busy bit to clear before writing a
request to the mailbox to avoid failures if the mailbox is still
busy from a previous transfer (Gregory Price)
Endpoint framework:
- Skip attempts to allocate from endpoint controller memory window if
the requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
handle controller-specific size and alignment constraints, and add
test cases to the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
observe DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
(Niklas Cassel)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks
'mmio' DT property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid
use-after-free (Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when
removing the secondary controller associated with an NTB (Zijun Hu)
Cadence PCIe controller driver:
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
Freescale i.MX6 PCIe controller driver:
- Fix suspend/resume support on i.MX6QDL, which has a hardware
erratum that prevents use of L2 (Stefan Eichenberger)
Intel VMD host bridge driver:
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 DT binding to require the exact number of
clocks for each SoC (Fei Shao)
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add DT and driver support for using either of the two PolarFire
Root Ports (Conor Dooley)
NVIDIA Tegra194 PCIe controller driver:
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
Qualcomm PCIe controller driver:
- Add qcom SAR2130P DT binding with an additional clock (Dmitry
Baryshkov)
- Enable MSI interrupts if 'global' IRQ is supported, since a
previous commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP
v5.80a and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the
qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
can be used by other Qcom platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the
link comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
to support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
'iommu-map' DT property and doesn't need BDF-to-SID translation
(Qiang Yu)
Rockchip PCIe controller driver:
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
.align value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead
of searching for it, and verify that the address was mapped (Damien
Le Moal)
- When mapping an endpoint window, verify that the address hasn't
been mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which
fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
(Damien Le Moal)
- Rename rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources() for consistency with similar DT
interfaces (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
it only in the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and
controller configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it
(Damien Le Moal)
- Add a handler for PERST# signal so we can detect host-initiated
resets and start link training after PERST# is deasserted (Damien
Le Moal)
Synopsys DesignWare PCIe controller driver:
- Clear outbound address on unmap so dw_pcie_find_index() won't match
an ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when
testing for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
TI J721E PCIe driver:
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
us), before deasserting PERST# to ensure power and refclk are
stable (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
Complex mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we
can do (Kishon Vijay Abraham I)
Miscellaneous:
- Reorganize kerneldoc parameter names to match order in function
signature (Julia Lawall)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)"
* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
tools: PCI: Fix incorrect printf format specifiers
...
If we go through the PCI shutdown or suspend path, we shutdown the
NIC but PTP remains registered. If the kernel continues to run for
a little bit, the periodic PTP .do_aux_work() function may be called
and it will read the PHC from the BAR register. Since the device
has already been disabled, it will cause a PCIe completion timeout.
Fix it by calling bnxt_ptp_clear() in the PCI shutdown/suspend
handlers. bnxt_ptp_clear() will unregister from PTP and
.do_aux_work() will be canceled.
In bnxt_resume(), we need to re-initialize PTP.
Fixes: a521c8a01d ("bnxt_en: Move bnxt_ptp_init() from bnxt_open() back to bnxt_init_one()")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of passing the 2nd parameter phc_cfg to bnxt_ptp_init().
Store it in bp->ptp_cfg so that the caller doesn't need to know what
the value should be.
In the next patch, we'll need to call bnxt_ptp_init() in bnxt_resume()
and this will make it easier.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The MTU setting at the time an XDP multi-buffer is attached
determines whether the aggregation ring will be used and the
rx_skb_func handler. This is done in bnxt_set_rx_skb_mode().
If the MTU is later changed, the aggregation ring setting may need
to be changed and it may become out-of-sync with the settings
initially done in bnxt_set_rx_skb_mode(). This may result in
random memory corruption and crashes as the HW may DMA data larger
than the allocated buffer size, such as:
BUG: kernel NULL pointer dereference, address: 00000000000003c0
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 17 PID: 0 Comm: swapper/17 Kdump: loaded Tainted: G S OE 6.1.0-226bf9805506 #1
Hardware name: Wiwynn Delta Lake PVT BZA.02601.0150/Delta Lake-Class1, BIOS F0E_3A12 08/26/2021
RIP: 0010:bnxt_rx_pkt+0xe97/0x1ae0 [bnxt_en]
Code: 8b 95 70 ff ff ff 4c 8b 9d 48 ff ff ff 66 41 89 87 b4 00 00 00 e9 0b f7 ff ff 0f b7 43 0a 49 8b 95 a8 04 00 00 25 ff 0f 00 00 <0f> b7 14 42 48 c1 e2 06 49 03 95 a0 04 00 00 0f b6 42 33f
RSP: 0018:ffffa19f40cc0d18 EFLAGS: 00010202
RAX: 00000000000001e0 RBX: ffff8e2c805c6100 RCX: 00000000000007ff
RDX: 0000000000000000 RSI: ffff8e2c271ab990 RDI: ffff8e2c84f12380
RBP: ffffa19f40cc0e48 R08: 000000000001000d R09: 974ea2fcddfa4cbf
R10: 0000000000000000 R11: ffffa19f40cc0ff8 R12: ffff8e2c94b58980
R13: ffff8e2c952d6600 R14: 0000000000000016 R15: ffff8e2c271ab990
FS: 0000000000000000(0000) GS:ffff8e3b3f840000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000003c0 CR3: 0000000e8580a004 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<IRQ>
__bnxt_poll_work+0x1c2/0x3e0 [bnxt_en]
To address the issue, we now call bnxt_set_rx_skb_mode() within
bnxt_change_mtu() to properly set the AGG rings configuration and
update rx_skb_func based on the new MTU value.
Additionally, BNXT_FLAG_NO_AGG_RINGS is cleared at the beginning of
bnxt_set_rx_skb_mode() to make sure it gets set or cleared based on
the current MTU.
Fixes: 08450ea98a ("bnxt_en: Fix max_mtu setting for multi-buf XDP")
Co-developed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
HWRM_RING_FREE followed by a HWRM_RING_ALLOC is not guaranteed to
have the same FW ring ID as before. So we must reinitialize the
RSS table with the correct ring IDs. Otherwise, traffic may not
resume properly if the restarted ring ID is stale. Since this
feature is only supported on P5_PLUS chips, we call
bnxt_vnic_set_rss_p5() to update the HW RSS table.
Fixes: 2d694c27d3 ("bnxt_en: implement netdev_queue_mgmt_ops")
Cc: David Wei <dw@davidwei.uk>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the return value from bnxt_get_media() to determine the port and
link modes. bnxt_get_media() returns the proper BNXT_MEDIA_KR when
the PHY is backplane. This will correct the ethtool settings for
backplane devices.
Fixes: 5d4e1bf606 ("bnxt_en: extend media types to supported and autoneg modes")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After successful PCIe AER recovery, FW will reset all resource
reservations. If it is IF_UP, the driver will call bnxt_open() and
all resources will be reserved again. It it is IF_DOWN, we should
call bnxt_reserve_rings() so that we can reserve resources including
RoCE resources to allow RoCE to resume after AER. Without this
patch, RoCE fails to resume in this IF_DOWN scenario.
Later, if it becomes IF_UP, bnxt_open() will see that resources have
been reserved and will not reserve again.
Fixes: fb1e6e562b ("bnxt_en: Fix AER recovery.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During initialization, the AF driver resets all blocks. The RPM (MAC)
block and NIX block operate on a credit-based model. When the NIX block
resets during active traffic flow, it doesn't release credits to the RPM
block. This causes the RPM FIFO to overflow, leading to receive traffic
struck.
To address this issue, the patch introduces the following changes:
1. Stop receiving traffic at the MAC level during AF driver
initialization.
2. Perform an X2P reset (prevents RXFIFO of all LMACS from pushing data)
3. Reset the NIX block.
4. Clear the X2P reset and re-enable receiving traffic.
Fixes: 54d557815e ("octeontx2-af: Reset all RVU blocks")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The corrected words register(FCFECX_VL0_CCW_LO)/Uncorrected words
register (FCFECX_VL0_NCCW_LO) of FCFEC counter has different LMAC
offset which needs to be accessed differently.
Fixes: 84ad364211 ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The earlier patch sets the 'Stats control register' for RPM
receive/transmit statistics instead of RSFEC statistics,
causing the driver to return stale FEC counters.
Fixes: 84ad364211 ("octeontx2-af: Add FEC stats for RPM/RPM_USX block")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Low network performance is observed even on RPMs with larger
FIFO lengths.
The cn10kb silicon has three RPM blocks with the following
FIFO sizes:
--------------------
| RPM0 | 256KB |
| RPM1 | 256KB |
| RPM2 | 128KB |
--------------------
The current design stores the FIFO length in a common structure for all
RPMs (mac_ops). As a result, the FIFO length of the last RPM is applied
to all RPMs, leading to reduced network performance.
This patch resolved the problem by storing the fifo length in per MAC
structure (cgx).
Fixes: b9d0fedc62 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Due to a bug in the previous patch, there is a mismatch
between the lmac type reported by the driver and the actual
hardware configuration.
Fixes: 3ad3f8f93c ("octeontx2-af: cn10k: MAC internal loopback support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On DWMAC3 and later, there's a RX Watchdog interrupt that's used for
interrupt coalescing. It's known to be buggy on some platforms, and
dwmac-socfpga appears to be one of them. Changing the interrupt
coalescing from ethtool doesn't appear to have any effect here.
Without disabling RIWT (Received Interrupt Watchdog Timer, I
believe...), we observe latencies while receiving traffic that amount to
around ~0.4ms. This was discovered with NTP but can be easily reproduced
with a simple ping. Without this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.657 ms
With this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.254 ms
Fixes: 801d233b73 ("net: stmmac: Add SOCFPGA glue driver")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241122141256.764578-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If the clock pep->clk was not enabled in pxa168_eth_probe,
it should not be disabled in any path.
Conversely, if it was enabled in pxa168_eth_probe, it must be disabled
in all error paths to ensure proper cleanup.
Use the devm_clk_get_enabled helper function to ensure proper call balance
for pep->clk.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: a49f37eed2 ("net: add Fast Ethernet driver for PXA168.")
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Link: https://patch.msgid.link/20241121200658.2203871-1-mordan@ispras.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround
broken TEF FIFO tail index erratum") introduced
mcp251xfd_get_tef_len() to get the number of unhandled transmit events
from the Transmit Event FIFO (TEF).
As the TEF has no head index, the driver uses the TX-FIFO's tail index
instead, assuming that send frames are completed.
When calculating the number of unhandled TEF events, that commit
didn't take mcp2518fd erratum DS80000789E 6. into account. According
to that erratum, the FIFOCI bits of a FIFOSTA register, here the
TX-FIFO tail index might be corrupted.
However here it seems the bit indicating that the TX-FIFO is
empty (MCP251XFD_REG_FIFOSTA_TFERFFIF) is not correct while the
TX-FIFO tail index is.
Assume that the TX-FIFO is indeed empty if:
- Chip's head and tail index are equal (len == 0).
- The TX-FIFO is less than half full.
(The TX-FIFO empty case has already been checked at the
beginning of this function.)
- No free buffers in the TX ring.
If the TX-FIFO is assumed to be empty, assume that the TEF is full and
return the number of elements in the TX-FIFO (which equals the number
of TEF elements).
If these assumptions are false, the driver might read to many objects
from the TEF. mcp251xfd_handle_tefif_one() checks the sequence numbers
and will refuse to process old events.
Reported-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Closes: https://patch.msgid.link/CAJ7t6HgaeQ3a_OtfszezU=zB-FqiZXqrnATJ3UujNoQJJf7GgA@mail.gmail.com
Fixes: b8e0ddd36c ("can: mcp251xfd: tef: prepare to workaround broken TEF FIFO tail index erratum")
Tested-by: Renjaya Raga Zenta <renjaya.zenta@formulatrix.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20241126-mcp251xfd-fix-length-calculation-v2-1-c2ed516ed6ba@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If an optional resource is found but fails to remap, return on failure.
Avoids any potential problems when using the iomapped resource as the
assumption is that it's available.
Fixes: 23a890d493 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241121193152.8966-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The f81604_handle_can_bus_errors() function only incremented the receive
error counter and never the transmit error counter, even if the ECC_DIR
flag reported that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 88da174369 ("can: usb: f81604: add Fintek F81604 support")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-13-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ems_usb_rx_err() function only incremented the receive error counter
and never the transmit error counter, even if the ECC_DIR flag reported
that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-12-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sun4i_can_err() function only incremented the receive error counter
and never the transmit error counter, even if the STA_ERR_DIR flag
reported that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
STA_ERR_DIR flag.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sja1000_err() function only incremented the receive error counter
and never the transmit error counter, even if the ECC_DIR flag reported
that an error had occurred during transmission.
Increment the receive/transmit error counter based on the value of the
ECC_DIR flag.
Fixes: 429da1cc84 ("can: Driver for the SJA1000 CAN controller")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-10-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hi3110_can_ist() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission.
The fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: 57e83fb9b7 ("can: hi311x: Add Holt HI-311x CAN driver")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ifi_canfd_handle_lec_err() function was incorrectly incrementing only
the receive error counter, even in cases of bit or acknowledgment errors
that occur during transmission.
Fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: 5bbd655a8b ("can: ifi: Add more detailed error reporting")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/20241122221650.633981-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The m_can_handle_lec_err() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission.
Fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ensure that the statistics related to state error counters
(i. e. warning, passive, and bus-off) are updated even in case the skb
allocation fails. Additionally, also handle bus-off state is now.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The commit a22bd630cf ("can: hi311x: do not report txerr and rxerr
during bus-off") removed the reporting of rxerr and txerr even in case
of correct operation (i. e. not bus-off).
The error count information added to the CAN frame after netif_rx() is
a potential use after free, since there is no guarantee that the skb
is in the same state. It might be freed or reused.
Fix the issue by postponing the netif_rx() call in case of txerr and
rxerr reporting.
Fixes: a22bd630cf ("can: hi311x: do not report txerr and rxerr during bus-off")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-5-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Call the function can_change_state() if the allocation of the skb
fails, as it handles the cf parameter when it is null.
Additionally, this ensures that the statistics related to state error
counters (i. e. warning, passive, and bus-off) are updated.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Set the initial eee_cfg values to have 'ethtool --show-eee ' display
the initial EEE configuration.
Fixes: 49168d1980 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Cc: <stable@vger.kernel.org>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241120083818.1079456-1-yong.liang.choong@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is an approach made to implement gs_usb firmware/driver based on
Zephyr RTOS. It was found that USB stack of Zephyr RTOS overwrites USB
EP addresses, if they have different last 4 bytes in absence of other
endpoints.
For example in case of gs_usb candlelight firmware EP-IN is 0x81 and
EP-OUT 0x02. If there are no additional USB endpoints, Zephyr RTOS will
overwrite EP-OUT to 0x01. More information can be found in the
discussion with Zephyr RTOS USB stack maintainer here:
https://github.com/zephyrproject-rtos/zephyr/issues/67812
There are already two different gs_usb FW driver implementations based
on Zephyr RTOS:
1. https://github.com/CANnectivity/cannectivity
(by: https://github.com/henrikbrixandersen)
2. https://github.com/zephyrproject-rtos/zephyr/compare/main...KozhinovAlexander:zephyr:gs_usb
(by: https://github.com/KozhinovAlexander)
At the moment both Zephyr RTOS implementations use dummy USB endpoint,
to overcome described USB stack behavior from Zephyr itself. Since
Zephyr RTOS is intended to be used on microcontrollers with very
constrained amount of resources (ROM, RAM) and additional endpoint
requires memory, it is more convenient to update the gs_usb driver in
the Linux kernel.
To fix this problem, update the gs_usb driver from using hard coded
endpoint numbers to evaluate the endpoint descriptors and use the
endpoints provided there.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Alexander Kozhinov <ak.alexander.kozhinov@gmail.com>
Link: https://patch.msgid.link/20241018212450.31746-1-ak.alexander.kozhinov@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit 6e86a1543c ("can: dev: provide optional GPIO based
termination support") GPIO based termination support was added.
For no particular reason that patch uses gpiod_set_value() to set the
GPIO. This leads to the following warning, if the systems uses a
sleeping GPIO, i.e. behind an I2C port expander:
| WARNING: CPU: 0 PID: 379 at /drivers/gpio/gpiolib.c:3496 gpiod_set_value+0x50/0x6c
| CPU: 0 UID: 0 PID: 379 Comm: ip Not tainted 6.11.0-20241016-1 #1 823affae360cc91126e4d316d7a614a8bf86236c
Replace gpiod_set_value() by gpiod_set_value_cansleep() to allow the
use of sleeping GPIOs.
Cc: Nicolai Buchwitz <nb@tipi-net.de>
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reported-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Tested-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Fixes: 6e86a1543c ("can: dev: provide optional GPIO based termination support")
Link: https://patch.msgid.link/20241121-dev-fix-can_set_termination-v1-1-41fa6e29216d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Previously, when the hardware version ID was determined to be invalid,
only an error message was printed without any further handling. Therefore,
this patch makes the necessary corrections to address this.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Previously, the reported speed was uniformly set to SPEED_5000, but the
RTL907XD-V1 actually operates at a speed of SPEED_10000. Therefore, this
patch makes the necessary correction.
Fixes: dd7f17c40f ("rtase: Implement ethtool function")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Different hardware requires different configurations, but this distinction
was not made previously. Additionally, the error message was not clear
enough. Therefore, this patch will address the issues mentioned above.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently mac80211's struct ieee80211_sta deflink is used to fetch any sta
related configurations in driver. With MLO multiple link sta's (struct
ieee80211_link_sta) are affiliated to an ML sta and corresponding link configs
are present in sta->link[]. Fetch link sta of corresponding link from ML sta
and use the same for configurations.
Add ath12k_mac_get_link_sta() helper to fetch ieee80211_link_sta from arsta. But as
ath12k_mac_op_sta_rc_update() is called in atomic context the helper cannot be
used and instead rcu_dereference() has to be called directly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-9-kvalo@kernel.org
Currently mac80211 vif's bss_conf is used to fetch any vif related
configurations in driver but with MLO multiple links are affiliated to a vif
and corresponding link configs are present in vif->link_conf[]. Fetch
link_conf for corresponding link from vif and use the same for configurations.
Add ath12k_mac_get_link_bss_conf() helper to fetch link_conf from arvif.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-8-kvalo@kernel.org
Currently ath12k's chanctx iterator functions use deflink of given ahvif and
bss_conf of corresponding vif to make sure the iterator returns intended vif.
An ML vif can have multiple affiliated links each having its own channel
context, hence iterate through the links of the given ahvif and use the link
objects (arvif and link_conf) to make sure the chan ctx iterator returns
intended link of the given vif.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-7-kvalo@kernel.org
Currently reoqueue tid setup uses lookup table (LUT) during peer association,
but for ML peer there will be multiple link peers (belonging to different
underlying firmware) affiliated to each other. Hence the reo queue should be
setup only on one of the links which is the primary link.
Add changes to create separate ML reo queue lookup table for ML peers and use
the same while setting up rx tid for ML peer's primary link. For ML peers use
ml_peer_id instead of peer_id to setup/lookup the reo queue entry in the LUT.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-6-kvalo@kernel.org
Currently, struct ieee80211_sta (sta) is used for many WMI and mac80211 ops but
for multi link station, driver should use struct ath12k_link_sta (arsta)
instead of sta. Add changes to use arsta object for WMI commands and other
mac80211 ops.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-5-kvalo@kernel.org
In case of Multi-link operation, data path peer setup and tid setup should be
done only for primary link of multi-link station. Add changes to introduce
primary link is peer. Currently, association link will be considered as primary
link.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-4-kvalo@kernel.org
Add changes to handle multi-link station state change with proper
link handling and add code changes for ML peer creation, peer deletion.
In ath12k_mac_assign_link_sta() initialise all arsta fields first and only then
call rcu_assign_pointer(). This is to make sure that readers don't have access
to arsta which is still modified.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-2-kvalo@kernel.org
VCAP API unit tests fail randomly with errors such as
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:387
Expected 134 + 7 == iter.offset, but
134 + 7 == 141 (0x8d)
iter.offset == 17214 (0x433e)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:388
Expected 5 == iter.reg_idx, but
iter.reg_idx == 702 (0x2be)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:389
Expected 11 == iter.reg_bitpos, but
iter.reg_bitpos == 15 (0xf)
# vcap_api_iterator_init_test: pass:0 fail:1 skip:0 total:1
Comments in the code state that "A typegroup table ends with an all-zero
terminator". Add the missing terminators.
Some of the typegroups did have a terminator of ".offset = 0, .width = 0,
.value = 0,". Replace those terminators with "{ }" (no trailing ',') for
consistency and to excplicitly state "this is a terminator".
Fixes: 67d637516f ("net: microchip: sparx5: Adding KUNIT test for the VCAP API")
Cc: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119213202.2884639-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Validate Wake-on-LAN (WoL) options in `lan78xx_set_wol` before calling
`usb_autopm_get_interface`. This prevents USB autopm refcounting issues
and ensures the adapter can properly enter autosuspend when invalid WoL
options are provided.
Fixes: eb9ad088f9 ("lan78xx: Check for supported Wake-on-LAN modes")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://patch.msgid.link/20241118140351.2398166-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware on Broadcom 1G chipsets have a known limitation
where they cannot handle DMA addresses that cross over 4GB.
When such an address is encountered, the hardware sets the
address overflow error bit in the DMA status register and
triggers a reset.
However, BCM57766 hardware is setting the overflow bit and
triggering a reset in some cases when there is no actual
underlying address overflow. The hardware team analyzed the
issue and concluded that it is happening when the status
block update has an address with higher (b16 to b31) bits
as 0xffff following a previous update that had lowest bits
as 0xffff.
To work around this bug in the BCM57766 hardware, set the
coherent dma mask from the current 64b to 31b. This will
ensure that upper bits of the status block DMA address are
always at most 0x7fff, thus avoiding the improper overflow
check described above. This work around is intended for only
status block and ring memories and has no effect on TX and
RX buffers as they do not require coherent memory.
Fixes: 72f2afb8a6 ("[TG3]: Add DMA address workaround")
Reported-by: Salam Noureddine <noureddine@arista.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20241119055741.147144-1-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add calls to `phy_device_free` after `fixed_phy_unregister` to fix a
memory leak that occurs when the device is unplugged. This ensures
proper cleanup of pseudo fixed-link PHYs.
Fixes: 89b36fb5e5 ("lan78xx: Lan7801 Support for Fixed PHY")
Cc: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In lan78xx_probe(), the buffer `buf` was being freed twice: once
implicitly through `usb_free_urb(dev->urb_intr)` with the
`URB_FREE_BUFFER` flag and again explicitly by `kfree(buf)`. This caused
a double free issue.
To resolve this, reordered `kmalloc()` and `usb_alloc_urb()` calls to
simplify the initialization sequence and removed the redundant
`kfree(buf)`. Now, `buf` is allocated after `usb_alloc_urb()`, ensuring
it is correctly managed by `usb_fill_int_urb()` and freed by
`usb_free_urb()` as intended.
Fixes: a6df95cae4 ("lan78xx: Fix memory allocation bug")
Cc: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a follow-up to 41ffcd9501 ("net: phy: fix phylib's dual
eee_enabled") and resolves an issue with genphy_c45_an_config_eee_aneg()
(called from genphy_c45_ethtool_set_eee) not seeing the new value of
phydev->eee_cfg.eee_enabled.
Fixes: 49168d1980 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seveal fixes scattered across the drivers and a few new features:
- Minor updates and bug fixes to hfi1, efa, iopob, bnxt, hns
- Force disassociate the userspace FD when hns does an async reset
- bnxt new features for optimized modify QP to skip certain stayes, CQ
coalescing, better debug dumping
- mlx5 new data placement ordering feature
- Faster destruction of mlx5 devx HW objects
- Improvements to RDMA CM mad handling
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCZz4ENwAKCRCFwuHvBreF
YQYQAP9R54r5J1Iylg+zqhCc+e/9oveuuZbfLvy/EJiEpmdprQEAgPs1RrB0z7U6
1xrVStUKNPhGd5XeVVZGkIV0zYv6Tw4=
=V5xI
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Seveal fixes scattered across the drivers and a few new features:
- Minor updates and bug fixes to hfi1, efa, iopob, bnxt, hns
- Force disassociate the userspace FD when hns does an async reset
- bnxt new features for optimized modify QP to skip certain stayes,
CQ coalescing, better debug dumping
- mlx5 new data placement ordering feature
- Faster destruction of mlx5 devx HW objects
- Improvements to RDMA CM mad handling"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (51 commits)
RDMA/bnxt_re: Correct the sequence of device suspend
RDMA/bnxt_re: Use the default mode of congestion control
RDMA/bnxt_re: Support different traffic class
IB/cm: Rework sending DREQ when destroying a cm_id
IB/cm: Do not hold reference on cm_id unless needed
IB/cm: Explicitly mark if a response MAD is a retransmission
RDMA/mlx5: Move events notifier registration to be after device registration
RDMA/bnxt_re: Cache MSIx info to a local structure
RDMA/bnxt_re: Refurbish CQ to NQ hash calculation
RDMA/bnxt_re: Refactor NQ allocation
RDMA/bnxt_re: Fail probe early when not enough MSI-x vectors are reserved
RDMA/hns: Fix different dgids mapping to the same dip_idx
RDMA/bnxt_re: Add set_func_resources support for P5/P7 adapters
RDMA/bnxt_re: Enhance RoCE SRIOV resource configuration design
bnxt_en: Add support for RoCE sriov configuration
RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg()
RDMA/hns: Fix out-of-order issue of requester when setting FENCE
RDMA/nldev: Add IB device and net device rename events
RDMA/mlx5: Add implementation for ufile_hw_cleanup device operation
RDMA/core: Move ib_uverbs_file struct to uverbs_types.h
...
The most significant set of changes is the per netns RTNL. The new
behavior is disabled by default, regression risk should be contained.
Notably the new config knob PTP_1588_CLOCK_VMCLOCK will inherit its
default value from PTP_1588_CLOCK_KVM, as the first is intended to be
a more reliable replacement for the latter.
Core
----
- Started a very large, in-progress, effort to make the RTNL lock
scope per network-namespace, thus reducing the lock contention
significantly in the containerized use-case, comprising:
- RCU-ified some relevant slices of the FIB control path
- introduce basic per netns locking helpers
- namespacified the IPv4 address hash table
- remove rtnl_register{,_module}() in favour of rtnl_register_many()
- refactor rtnl_{new,del,set}link() moving as much validation as
possible out of RTNL lock
- convert all phonet doit() and dumpit() handlers to RCU
- convert IPv4 addresses manipulation to per-netns RTNL
- convert virtual interface creation to per-netns RTNL
the per-netns lock infra is guarded by the CONFIG_DEBUG_NET_SMALL_RTNL
knob, disabled by default ad interim.
- Introduce NAPI suspension, to efficiently switching between busy
polling (NAPI processing suspended) and normal processing.
- Migrate the IPv4 routing input, output and control path from direct
ToS usage to DSCP macros. This is a work in progress to make ECN
handling consistent and reliable.
- Add drop reasons support to the IPv4 rotue input path, allowing
better introspection in case of packets drop.
- Make FIB seqnum lockless, dropping RTNL protection for read
access.
- Make inet{,v6} addresses hashing less predicable.
- Allow providing timestamp OPT_ID via cmsg, to correlate TX packets
and timestamps
Things we sprinkled into general kernel code
--------------------------------------------
- Add small file operations for debugfs, to reduce the struct ops size.
- Refactoring and optimization for the implementation of page_frag API,
This is a preparatory work to consolidate the page_frag
implementation.
Netfilter
---------
- Optimize set element transactions to reduce memory consumption
- Extended netlink error reporting for attribute parser failure.
- Make legacy xtables configs user selectable, giving users
the option to configure iptables without enabling any other config.
- Address a lot of false-positive RCU issues, pointed by recent
CI improvements.
BPF
---
- Put xsk sockets on a struct diet and add various cleanups. Overall,
this helps to bump performance by 12% for some workloads.
- Extend BPF selftests to increase coverage of XDP features in
combination with BPF cpumap.
- Optimize and homogenize bpf_csum_diff helper for all archs and also
add a batch of new BPF selftests for it.
- Extend netkit with an option to delegate skb->{mark,priority}
scrubbing to its BPF program.
- Make the bpf_get_netns_cookie() helper available also to tc(x) BPF
programs.
Protocols
---------
- Introduces 4-tuple hash for connected udp sockets, speeding-up
significantly connected sockets lookup.
- Add a fastpath for some TCP timers that usually expires after close,
the socket lock contention.
- Add inbound and outbound xfrm state caches to speed up state lookups.
- Avoid sending MPTCP advertisements on stale subflows, reducing
risks on loosing them.
- Make neighbours table flushing more scalable, maintaining per device
neigh lists.
Driver API
----------
- Introduce a unified interface to configure transmission H/W shaping,
and expose it to user-space via generic-netlink.
- Add support for per-NAPI config via netlink. This makes napi
configuration persistent across queues removal and re-creation.
Requires driver updates, currently supported drivers are:
nVidia/Mellanox mlx4 and mlx5, Broadcom brcm and Intel ice.
- Add ethtool support for writing SFP / PHY firmware blocks.
- Track RSS context allocation from ethtool core.
- Implement support for mirroring to DSA CPU port, via TC mirror
offload.
- Consolidate FDB updates notification, to avoid duplicates on
device-specific entries.
- Expose DPLL clock quality level to the user-space.
- Support master-slave PHY config via device tree.
Tests and tooling
-----------------
- forwarding: introduce deferred commands, to simplify
the cleanup phase
Drivers
-------
- Updated several drivers - Amazon vNic, Google vNic, Microsoft vNic,
Intel e1000e and Broadcom Tigon3 - to use netdev-genl to link the
IRQs and queues to NAPI IDs, allowing busy polling and better
introspection.
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- mlx5:
- a large refactor to implement support for cross E-Switch
scheduling
- refactor H/W conter management to let it scale better
- H/W GRO cleanups
- Intel (100G, ice)::
- adds support for ethtool reset
- implement support for per TX queue H/W shaping
- AMD/Solarflare:
- implement per device queue stats support
- Broadcom (bnxt):
- improve wildcard l4proto on IPv4/IPv6 ntuple rules
- Marvell Octeon:
- Adds representor support for each Resource Virtualization Unit
(RVU) device.
- Hisilicon:
- adds support for the BMC Gigabit Ethernet
- IBM (EMAC):
- driver cleanup and modernization
- Cisco (VIC):
- raise the queues number limit to 256
- Ethernet virtual:
- Google vNIC:
- implements page pool support
- macsec:
- inherit lower device's features and TSO limits when offloading
- virtio_net:
- enable premapped mode by default
- support for XDP socket(AF_XDP) zerocopy TX
- wireguard:
- set the TSO max size to be GSO_MAX_SIZE, to aggregate larger
packets.
- Ethernet NICs embedded and virtual:
- Broadcom ASP:
- enable software timestamping
- Freescale:
- add enetc4 PF driver
- MediaTek: Airoha SoC:
- implement BQL support
- RealTek r8169:
- enable TSO by default on r8168/r8125
- implement extended ethtool stats
- Renesas AVB:
- enable TX checksum offload
- Synopsys (stmmac):
- support header splitting for vlan tagged packets
- move common code for DWMAC4 and DWXGMAC into a separate FPE
module.
- Add the dwmac driver support for T-HEAD TH1520 SoC
- Synopsys (xpcs):
- driver refactor and cleanup
- TI:
- icssg_prueth: add VLAN offload support
- Xilinx emaclite:
- adds clock support
- Ethernet switches:
- Microchip:
- implement support for the lan969x Ethernet switch family
- add LAN9646 switch support to KSZ DSA driver
- Ethernet PHYs:
- Marvel: 88q2x: enable auto negotiation
- Microchip: add support for LAN865X Rev B1 and LAN867X Rev C1/C2
- PTP:
- Add support for the Amazon virtual clock device
- Add PtP driver for s390 clocks
- WiFi:
- mac80211
- EHT 1024 aggregation size for transmissions
- new operation to indicate that a new interface is to be added
- support radio separation of multi-band devices
- move wireless extension spy implementation to libiw
- Broadcom:
- brcmfmac: optional LPO clock support
- Microchip:
- add support for Atmel WILC3000
- Qualcomm (ath12k):
- firmware coredump collection support
- add debugfs support for a multitude of statistics
- Qualcomm (ath5k):
- Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
- Realtek:
- rtw88: 8821au and 8812au USB adapters support
- rtw89: add thermal protection
- rtw89: fine tune BT-coexsitence to improve user experience
- rtw89: firmware secure boot for WiFi 6 chip
- Bluetooth
- add Qualcomm WCN785x support for ids Foxconn 0xe0fc/0xe0f3 and
0x13d3:0x3623
- add Realtek RTL8852BE support for id Foxconn 0xe123
- add MediaTek MT7920 support for wireless module ids
- btintel_pcie: add handshake between driver and firmware
- btintel_pcie: add recovery mechanism
- btnxpuart: add GPIO support to power save feature
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEg1AjqC77wbdLX2LbKSR5jcyPE6QFAmc8sukSHHBhYmVuaUBy
ZWRoYXQuY29tAAoJECkkeY3MjxOkLEYQAIMM6Qjh0bh3Byr3gOS1xZzXG+APLjP4
9Jr0p3i+X53i90jvVqzeVO5FTc95MVHSKZ3kvPkDMXSLUaEJxocNHCI5Dzl/2/qL
wWdpUB6/ou+jKB4Bn6Z8OvVODT7qrr0tVa9M2/fuKWrIsOU/ntIhG8EhnGddk5U/
vKPSf5PUIb81uNRnF58VusY3wrT1dEoh9VfJYxL+ST+inPxjEAMy6Y+lmlsjGaSX
jrS+Pp9KYiUwl3Qt0AQs+cG4OHkJdjbnChrfosWwpkiyddO8klVq06+wX/TiSzfF
b9VZtBfy/GZs3lkE1mQkcILdtX5pP3YHQdpsuxFfVI0JHVszx2ck7WdoRux/8F0v
kKZsYcO7bH9I1wMFP66Ff9hIbdEQaeucK+KdDkXyPNMfP91Vzmfjii8IBxOC36Ie
BbOeFUrXyTxxJ2u0vf/X9JtIq8bcrkNrSd1n1jlGPMqG3FVzsY95+Oi4qfsyeUbl
lS1PlVTqPMPFdX54HnxM3y2rJjhd7iXhkvmtuXNjRFThXlOiK3maAPWlM1aZ3b8u
Vjs4JFUsW0tleZG+RzANjsGjXbf7AiPUGLZt+acem0K+fcjG4i5aGIAJrxwa/ORx
eG74IZRt5cOI371W7gNLGHjwnuge8tFPgOWcRP2eozNm7jvMYALBejYS7eWUTvaf
THcvVM+bupEZ
=GzPr
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"The most significant set of changes is the per netns RTNL. The new
behavior is disabled by default, regression risk should be contained.
Notably the new config knob PTP_1588_CLOCK_VMCLOCK will inherit its
default value from PTP_1588_CLOCK_KVM, as the first is intended to be
a more reliable replacement for the latter.
Core:
- Started a very large, in-progress, effort to make the RTNL lock
scope per network-namespace, thus reducing the lock contention
significantly in the containerized use-case, comprising:
- RCU-ified some relevant slices of the FIB control path
- introduce basic per netns locking helpers
- namespacified the IPv4 address hash table
- remove rtnl_register{,_module}() in favour of
rtnl_register_many()
- refactor rtnl_{new,del,set}link() moving as much validation as
possible out of RTNL lock
- convert all phonet doit() and dumpit() handlers to RCU
- convert IPv4 addresses manipulation to per-netns RTNL
- convert virtual interface creation to per-netns RTNL
the per-netns lock infrastructure is guarded by the
CONFIG_DEBUG_NET_SMALL_RTNL knob, disabled by default ad interim.
- Introduce NAPI suspension, to efficiently switching between busy
polling (NAPI processing suspended) and normal processing.
- Migrate the IPv4 routing input, output and control path from direct
ToS usage to DSCP macros. This is a work in progress to make ECN
handling consistent and reliable.
- Add drop reasons support to the IPv4 rotue input path, allowing
better introspection in case of packets drop.
- Make FIB seqnum lockless, dropping RTNL protection for read access.
- Make inet{,v6} addresses hashing less predicable.
- Allow providing timestamp OPT_ID via cmsg, to correlate TX packets
and timestamps
Things we sprinkled into general kernel code:
- Add small file operations for debugfs, to reduce the struct ops
size.
- Refactoring and optimization for the implementation of page_frag
API, This is a preparatory work to consolidate the page_frag
implementation.
Netfilter:
- Optimize set element transactions to reduce memory consumption
- Extended netlink error reporting for attribute parser failure.
- Make legacy xtables configs user selectable, giving users the
option to configure iptables without enabling any other config.
- Address a lot of false-positive RCU issues, pointed by recent CI
improvements.
BPF:
- Put xsk sockets on a struct diet and add various cleanups. Overall,
this helps to bump performance by 12% for some workloads.
- Extend BPF selftests to increase coverage of XDP features in
combination with BPF cpumap.
- Optimize and homogenize bpf_csum_diff helper for all archs and also
add a batch of new BPF selftests for it.
- Extend netkit with an option to delegate skb->{mark,priority}
scrubbing to its BPF program.
- Make the bpf_get_netns_cookie() helper available also to tc(x) BPF
programs.
Protocols:
- Introduces 4-tuple hash for connected udp sockets, speeding-up
significantly connected sockets lookup.
- Add a fastpath for some TCP timers that usually expires after
close, the socket lock contention.
- Add inbound and outbound xfrm state caches to speed up state
lookups.
- Avoid sending MPTCP advertisements on stale subflows, reducing
risks on loosing them.
- Make neighbours table flushing more scalable, maintaining per
device neigh lists.
Driver API:
- Introduce a unified interface to configure transmission H/W
shaping, and expose it to user-space via generic-netlink.
- Add support for per-NAPI config via netlink. This makes napi
configuration persistent across queues removal and re-creation.
Requires driver updates, currently supported drivers are:
nVidia/Mellanox mlx4 and mlx5, Broadcom brcm and Intel ice.
- Add ethtool support for writing SFP / PHY firmware blocks.
- Track RSS context allocation from ethtool core.
- Implement support for mirroring to DSA CPU port, via TC mirror
offload.
- Consolidate FDB updates notification, to avoid duplicates on
device-specific entries.
- Expose DPLL clock quality level to the user-space.
- Support master-slave PHY config via device tree.
Tests and tooling:
- forwarding: introduce deferred commands, to simplify the cleanup
phase
Drivers:
- Updated several drivers - Amazon vNic, Google vNic, Microsoft vNic,
Intel e1000e and Broadcom Tigon3 - to use netdev-genl to link the
IRQs and queues to NAPI IDs, allowing busy polling and better
introspection.
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- mlx5:
- a large refactor to implement support for cross E-Switch
scheduling
- refactor H/W conter management to let it scale better
- H/W GRO cleanups
- Intel (100G, ice)::
- add support for ethtool reset
- implement support for per TX queue H/W shaping
- AMD/Solarflare:
- implement per device queue stats support
- Broadcom (bnxt):
- improve wildcard l4proto on IPv4/IPv6 ntuple rules
- Marvell Octeon:
- Add representor support for each Resource Virtualization Unit
(RVU) device.
- Hisilicon:
- add support for the BMC Gigabit Ethernet
- IBM (EMAC):
- driver cleanup and modernization
- Cisco (VIC):
- raise the queues number limit to 256
- Ethernet virtual:
- Google vNIC:
- implement page pool support
- macsec:
- inherit lower device's features and TSO limits when
offloading
- virtio_net:
- enable premapped mode by default
- support for XDP socket(AF_XDP) zerocopy TX
- wireguard:
- set the TSO max size to be GSO_MAX_SIZE, to aggregate larger
packets.
- Ethernet NICs embedded and virtual:
- Broadcom ASP:
- enable software timestamping
- Freescale:
- add enetc4 PF driver
- MediaTek: Airoha SoC:
- implement BQL support
- RealTek r8169:
- enable TSO by default on r8168/r8125
- implement extended ethtool stats
- Renesas AVB:
- enable TX checksum offload
- Synopsys (stmmac):
- support header splitting for vlan tagged packets
- move common code for DWMAC4 and DWXGMAC into a separate FPE
module.
- add dwmac driver support for T-HEAD TH1520 SoC
- Synopsys (xpcs):
- driver refactor and cleanup
- TI:
- icssg_prueth: add VLAN offload support
- Xilinx emaclite:
- add clock support
- Ethernet switches:
- Microchip:
- implement support for the lan969x Ethernet switch family
- add LAN9646 switch support to KSZ DSA driver
- Ethernet PHYs:
- Marvel: 88q2x: enable auto negotiation
- Microchip: add support for LAN865X Rev B1 and LAN867X Rev C1/C2
- PTP:
- Add support for the Amazon virtual clock device
- Add PtP driver for s390 clocks
- WiFi:
- mac80211
- EHT 1024 aggregation size for transmissions
- new operation to indicate that a new interface is to be added
- support radio separation of multi-band devices
- move wireless extension spy implementation to libiw
- Broadcom:
- brcmfmac: optional LPO clock support
- Microchip:
- add support for Atmel WILC3000
- Qualcomm (ath12k):
- firmware coredump collection support
- add debugfs support for a multitude of statistics
- Qualcomm (ath5k):
- Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
- Realtek:
- rtw88: 8821au and 8812au USB adapters support
- rtw89: add thermal protection
- rtw89: fine tune BT-coexsitence to improve user experience
- rtw89: firmware secure boot for WiFi 6 chip
- Bluetooth
- add Qualcomm WCN785x support for ids Foxconn 0xe0fc/0xe0f3 and
0x13d3:0x3623
- add Realtek RTL8852BE support for id Foxconn 0xe123
- add MediaTek MT7920 support for wireless module ids
- btintel_pcie: add handshake between driver and firmware
- btintel_pcie: add recovery mechanism
- btnxpuart: add GPIO support to power save feature"
* tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1475 commits)
mm: page_frag: fix a compile error when kernel is not compiled
Documentation: tipc: fix formatting issue in tipc.rst
selftests: nic_performance: Add selftest for performance of NIC driver
selftests: nic_link_layer: Add selftest case for speed and duplex states
selftests: nic_link_layer: Add link layer selftest for NIC driver
bnxt_en: Add FW trace coredump segments to the coredump
bnxt_en: Add a new ethtool -W dump flag
bnxt_en: Add 2 parameters to bnxt_fill_coredump_seg_hdr()
bnxt_en: Add functions to copy host context memory
bnxt_en: Do not free FW log context memory
bnxt_en: Manage the FW trace context memory
bnxt_en: Allocate backing store memory for FW trace logs
bnxt_en: Add a 'force' parameter to bnxt_free_ctx_mem()
bnxt_en: Refactor bnxt_free_ctx_mem()
bnxt_en: Add mem_valid bit to struct bnxt_ctx_mem_type
bnxt_en: Update firmware interface spec to 1.10.3.85
selftests/bpf: Add some tests with sockmap SK_PASS
bpf: fix recursive lock when verdict program return SK_PASS
wireguard: device: support big tcp GSO
wireguard: selftests: load nf_conntrack if not present
...
When compiling the ath11k driver using clang with KASAN enabled, the
following warning is observed:
drivers/net/wireless/ath/ath11k/wow.c:672:5: warning: stack frame size (1336) exceeds limit (1024) in 'ath11k_wow_op_suspend' [-Wframe-larger-than]
This is similar to the issue found in ath12k/qmi.c that was discussed
in [1] and fixed with [2]. The issue is that clang inlining can
explode stack usage.
ath11k_wow_op_suspend() itself is a pretty lightweight function, but
it dispatches to several other functions which do the real work. One
path in particular is:
ath11k_wow_op_suspend()
ath11k_wow_set_wakeups()
ath11k_vif_wow_set_wakeups()
ath11k_wow_convert_8023_to_80211()
Of these, ath11k_wow_convert_8023_to_80211() has non-trivial stack
usage, so mark it as 'noinline_for_stack' to prevent it from being
inlined in ath11k_wow_op_suspend(), thereby eliminating the excessive
stack usage.
Compile tested only.
Link: https://msgid.link/bc214795-1c51-4cb7-922f-67d6ef98bff2@quicinc.com # [1]
Link: https://patch.msgid.link/20241028-ath12k_qmi_driver_event_work-v1-1-0d532eb593fa@quicinc.com # [2]
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241119-ath11k-noinline-v1-3-4ec0a8aa30b2@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
When compiling the ath11k driver using clang with KASAN enabled, the
following warning is observed:
drivers/net/wireless/ath/ath11k/dp_rx.c:5244:5: warning: stack frame size (1304) exceeds limit (1024) in 'ath11k_dp_rx_process_mon_status' [-Wframe-larger-than]
This is similar to the issue found in ath12k/qmi.c that was discussed
in [1] and fixed with [2]. The issue is that clang inlining can
explode stack usage.
ath11k_dp_rx_process_mon_status() itself is a pretty
lightweight function, but it dispatches to several other functions
which do the real work:
ath11k_dp_rx_process_mon_status()
ath11k_dp_rx_reap_mon_status_ring()
ath11k_dp_rx_mon_dest_process()
ath11k_dp_rx_mon_mpdu_pop() *
ath11k_dp_rx_mon_deliver()
ath11k_dp_rx_mon_merg_msdus()
ath11k_dp_rx_deliver_msdu()
ath11k_dp_rx_update_peer_stats()
Of these, only ath11k_dp_rx_mon_mpdu_pop() has non-trivial stack
usage, so mark that function as 'noinline_for_stack' to prevent it
from being inlined in ath11k_dp_rx_process_mon_status(), thereby
eliminating the excessive stack usage.
Compile tested only.
Link: https://msgid.link/bc214795-1c51-4cb7-922f-67d6ef98bff2@quicinc.com # [1]
Link: https://patch.msgid.link/20241028-ath12k_qmi_driver_event_work-v1-1-0d532eb593fa@quicinc.com # [2]
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241119-ath11k-noinline-v1-2-4ec0a8aa30b2@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
When compiling the ath11k driver using clang with KASAN enabled, the
following warning is observed:
drivers/net/wireless/ath/ath11k/qmi.c:3199:13: warning: stack frame size (1560) exceeds limit (1024) in 'ath11k_qmi_driver_event_work' [-Wframe-larger-than]
This is similar to the issue found in ath12k/qmi.c that was discussed
in [1] and fixed with [2]. The issue is that clang inlining can
explode stack usage.
Just as in ath12k, ath11k_qmi_driver_event_work() itself is a pretty
lightweight function, but it dispatches to several other functions
which do the real work:
ath11k_qmi_driver_event_work()
ath11k_qmi_event_server_arrive()
ath11k_qmi_fw_ind_register_send()
ath11k_qmi_host_cap_send() *
ath11k_qmi_event_load_bdf()
ath11k_qmi_event_mem_request()
ath11k_qmi_respond_fw_mem_request()
ath11k_qmi_event_load_bdf()
ath11k_qmi_wlanfw_m3_info_send() *
ath11k_qmi_m3_load()
ath11k_qmi_process_coldboot_calibration()
Of these, the two marked with * have non-trivial stack usage. Mark
those functions as 'noinline_for_stack' to prevent them from being
inlined in ath12k_qmi_driver_event_work(), thereby eliminating the
excessive stack usage.
Note that this approach is a bit more "surgical" than the ath12k
approach as only the two functions with the largest stack usage are
modified.
Compile tested only.
Link: https://msgid.link/bc214795-1c51-4cb7-922f-67d6ef98bff2@quicinc.com # [1]
Link: https://patch.msgid.link/20241028-ath12k_qmi_driver_event_work-v1-1-0d532eb593fa@quicinc.com # [2]
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241119-ath11k-noinline-v1-1-4ec0a8aa30b2@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Currently in ath12k_htt_print_tx_pdev_mumimo_grp_stats_tlv() the
htt_stats_buf->ul_mumimo_grp_best_usrs array is printed using
print_array_to_buf_index() with a stats_index of 1. This is meant
to convey the semantic that first entry in ul_mumimo_grp_best_usrs
is associated with user 1. However, unlike some of the other "usr"
arrays which have that semantic, ul_mumimo_grp_best_usrs does not
have that semantic. Instead the first entry corresponds to user 0.
Fix the issue by calling the API - print_array_to_buf(), instead of
print_array_to_buf_index().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241118035722.1755373-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
QCA6698AQ IP core is the same as WCN6855 hw2.1, they share the same
PCI device ID, the same major and minor version numbers, the same
register address, and same HAL descriptors, etc. The most significant
difference is that QCA6698AQ has different RF, IPA, thermal, etc.
Follow the approach done in commit 5dc9d1a55e ("wifi: ath11k: add
support for QCA2066"), enumerate the subversion number to identify the
specific card.
Tested-on: QCA6698AQ hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241031000541.3331606-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Correct spelling here and there as suggested by codespell.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241111070152.85140-4-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Remove initialized but otherwise unused 'rx_status_q' member of
'struct ath11k_mon_data' and adjust 'ath11k_dp_rx_pdev_mon_status_attach'
accordingly. Compile tested only.
Fixes: 67a9d399fc ("ath11k: enable RX PPDU stats in monitor co-exist mode")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241111070152.85140-3-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Remove unused 'ap_constraint_power' field of 'struct
ath11k_reg_tpc_power_info' and adjust related comment.
Compile tested only.
Fixes: 6f4e235be6 ("wifi: ath11k: add parse of transmit power envelope element")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241111070152.85140-2-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Remove set but otherwise unused 'tx_seq_no' member of 'struct ath11k_vif',
adjust 'ath11k_control_beaconing()' accordingly. This field was actually
unused since an initial commit of the driver. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241111070152.85140-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
KASAN reported a memory allocation issue in wcn->chan_survey
due to incorrect size calculation.
This commit uses kcalloc to allocate memory for wcn->chan_survey,
ensuring proper initialization and preventing the use of uninitialized
values when there are no frames on the channel.
Fixes: 29696e0aa4 ("wcn36xx: Track SNR and RSSI for each RX frame")
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Acked-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://patch.msgid.link/20241104-wcn36xx-memory-allocation-v1-1-5ec901cf37b6@mainlining.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
