USB5744 SMBus initialization is done once in probe() and doing it in resume
is not supported so avoid going into suspend and reset the HUB.
There is a sysfs property 'always_powered_in_suspend' to implement this
feature but since default state should be set to a working configuration
so override this property value.
It fixes the suspend/resume testcase on Kria KR260 Robotics Starter Kit.
Fixes: 6782311d04df ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Cc: stable@vger.kernel.org
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1733165302-1694891-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure type safety by using min_t() instead of min().
Also add the explicit `unsigned int` as scripts/checkpatch.pl warns about:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-5-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Lenovo platforms, the patch works around problems with ov2740
sensor initialization, which manifest themself like below:
[ 4.540476] ov2740 i2c-INT3474:01: error -EIO: failed to find sensor
[ 4.542066] ov2740 i2c-INT3474:01: probe with driver ov2740 failed with error -5
or
[ 7.742633] ov2740 i2c-INT3474:01: chip id mismatch: 2740 != 0
[ 7.742638] ov2740 i2c-INT3474:01: error -ENXIO: failed to find sensor
and also by random failures of video stream start.
Issue can be reproduced by this script:
n=0
k=0
while [ $n -lt 50 ] ; do
sudo modprobe -r ov2740
sleep `expr $RANDOM % 5`
sudo modprobe ov2740
if media-ctl -p | grep -q ov2740 ; then
let k++
fi
let n++
done
echo Success rate $k/$n
Without the patch, success rate is approximately 15 or 50 tries.
With the patch it does not fail.
This problem is some hardware or firmware malfunction, that can not be
easy debug and fix. While setting small autosuspend delay is not perfect
workaround as user can configure it to any value, it will prevent
the failures by default.
Additionally setting small autosuspend delay should have positive effect
on power consumption as for most ljca workloads device is used for just
a few milliseconds flowed by long periods of at least 100ms of inactivity
(usually more).
Fixes: acd6199f195d ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-2-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not mark interface as ready to suspend when we are still waiting
for response messages from the device.
Fixes: acd6199f195d ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZwu6fw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yly6QCfdXwmKEqG4H7xonERzmEkP9/sYtoAnAsafKV5
5pWgy7Jw+WH1s1L7IzGy
=xrG1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
net/9p/usbg: Fix build error
USB: yurex: kill needless initialization in yurex_read
Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
usb: xhci: Fix problem with xhci resume from suspend
usb: misc: onboard_usb_dev: introduce new config symbol for usb5744 SMBus support
usb: dwc3: core: Stop processing of pending events if controller is halted
usb: dwc3: re-enable runtime PM after failed resume
usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
usb: gadget: core: force synchronous registration
[Syzbot reported two possible deadlocks]
The first possible deadlock is:
WARNING: possible recursive locking detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
--------------------------------------------
syz-executor363/2651 is trying to acquire lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x15d/0x2c0 drivers/usb/misc/chaoskey.c:322
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x7f/0x2c0 drivers/usb/misc/chaoskey.c:299
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(chaoskey_list_lock);
lock(chaoskey_list_lock);
*** DEADLOCK ***
The second possible deadlock is:
WARNING: possible circular locking dependency detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
------------------------------------------------------
kworker/0:2/804 is trying to acquire lock:
ffffffff899dadb0 (minor_rwsem){++++}-{3:3}, at: usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_disconnect+0xa8/0x2a0 drivers/usb/misc/chaoskey.c:235
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (chaoskey_list_lock){+.+.}-{3:3}:
__mutex_lock_common kernel/locking/mutex.c:608 [inline]
__mutex_lock+0x175/0x9c0 kernel/locking/mutex.c:752
chaoskey_open+0xdd/0x220 drivers/usb/misc/chaoskey.c:274
usb_open+0x186/0x220 drivers/usb/core/file.c:47
chrdev_open+0x237/0x6a0 fs/char_dev.c:414
do_dentry_open+0x6cb/0x1390 fs/open.c:958
vfs_open+0x82/0x3f0 fs/open.c:1088
do_open fs/namei.c:3774 [inline]
path_openat+0x1e6a/0x2d60 fs/namei.c:3933
do_filp_open+0x1dc/0x430 fs/namei.c:3960
do_sys_openat2+0x17a/0x1e0 fs/open.c:1415
do_sys_open fs/open.c:1430 [inline]
__do_sys_openat fs/open.c:1446 [inline]
__se_sys_openat fs/open.c:1441 [inline]
__x64_sys_openat+0x175/0x210 fs/open.c:1441
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (minor_rwsem){++++}-{3:3}:
check_prev_add kernel/locking/lockdep.c:3161 [inline]
check_prevs_add kernel/locking/lockdep.c:3280 [inline]
validate_chain kernel/locking/lockdep.c:3904 [inline]
__lock_acquire+0x250b/0x3ce0 kernel/locking/lockdep.c:5202
lock_acquire.part.0+0x11b/0x380 kernel/locking/lockdep.c:5825
down_write+0x93/0x200 kernel/locking/rwsem.c:1577
usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
chaoskey_disconnect+0xb7/0x2a0 drivers/usb/misc/chaoskey.c:236
usb_unbind_interface+0x1e8/0x970 drivers/usb/core/driver.c:461
device_remove drivers/base/dd.c:569 [inline]
device_remove+0x122/0x170 drivers/base/dd.c:561
__device_release_driver drivers/base/dd.c:1273 [inline]
device_release_driver_internal+0x44a/0x610 drivers/base/dd.c:1296
bus_remove_device+0x22f/0x420 drivers/base/bus.c:576
device_del+0x396/0x9f0 drivers/base/core.c:3864
usb_disable_device+0x36c/0x7f0 drivers/usb/core/message.c:1418
usb_disconnect+0x2e1/0x920 drivers/usb/core/hub.c:2304
hub_port_connect drivers/usb/core/hub.c:5361 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5661 [inline]
port_event drivers/usb/core/hub.c:5821 [inline]
hub_event+0x1bed/0x4f40 drivers/usb/core/hub.c:5903
process_one_work+0x9c5/0x1ba0 kernel/workqueue.c:3229
process_scheduled_works kernel/workqueue.c:3310 [inline]
worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391
kthread+0x2c1/0x3a0 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(chaoskey_list_lock);
lock(minor_rwsem);
lock(chaoskey_list_lock);
lock(minor_rwsem);
*** DEADLOCK ***
[Analysis]
The first is AA lock, it because wrong logic, it need a unlock.
The second is AB lock, it needs to rearrange the order of lock usage.
Fixes: 422dc0a4d12d ("USB: chaoskey: fail open after removal")
Reported-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=685e14d04fe35692d3bc
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Tested-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/tencent_84EB865C89862EC22EE94CB3A7C706C59206@qq.com
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 86b20af11e84c26ae3fde4dcc4f490948e3f8035.
This patch leads to passing 0 to simple_read_from_buffer()
as a fifth argument, turning the read method into a nop.
The change is fundamentally flawed, as it breaks the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241007094004.242122-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new kernel config symbol for Microchip usb5744 SMBus programming
support. Since usb5744 i2c initialization routine uses i2c SMBus APIs these
APIs should only be invoked when kernel has I2C support. This new kernel
config describes the dependency on I2C kernel support and fix the below
build issues when USB_ONBOARD_DEV=y and CONFIG_I2C=m.
riscv64-linux-ld: drivers/usb/misc/onboard_usb_dev.o:
undefined reference to `i2c_find_device_by_fwnode'
drivers/usb/misc/onboard_usb_dev.c:408:(.text+0xb24): undefined
reference to `i2c_smbus_write_block_data'
<snip>
Parsing of the i2c-bus bus handle is not put under usb5744 kernel config
check as the intention is to report an error when DT is configured for
usb5744 SMBus support and kernel has USB_ONBOARD_DEV_USB5744 disabled.
Fixes: 6782311d04df ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409140539.3Axwv38m-lkp@intel.com/
Acked-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Link: https://lore.kernel.org/r/1727529992-476088-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chaoskey_open() takes the lock only to increase the
counter of openings. That means that the mutual exclusion
with chaoskey_disconnect() cannot prevent an increase
of the counter and chaoskey_open() returning a success.
If that race is hit, chaoskey_disconnect() will happily
free all resources associated with the device after
it has dropped the lock, as it has read the counter
as zero.
To prevent this race chaoskey_open() has to check
the presence of the device under the lock.
However, the current per device lock cannot be used,
because it is a part of the data structure to be
freed. Hence an additional global mutex is needed.
The issue is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+422188bce66e76020e55@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=422188bce66e76020e55
Fixes: 66e3e591891da ("usb: Add driver for Altus Metrum ChaosKey device (v2)")
Rule: add
Link: https://lore.kernel.org/stable/20241002132201.552578-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20241002132201.552578-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IO yurex_write() needs to wait for in order to have a device
ready for writing again can take a long time time.
Consequently the sleep is done in an interruptible state.
Therefore others waiting for yurex_write() itself to finish should
use mutex_lock_interruptible.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 6bc235a2e24a5 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Rule: add
Link: https://lore.kernel.org/stable/20240924084415.300557-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20240924084415.300557-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iowarrior_read() uses the iowarrior dev structure, but does not use any
lock on the structure. This can cause various bugs including data-races,
so it is more appropriate to use a mutex lock to safely protect the
iowarrior dev structure. When using a mutex lock, you should split the
branch to prevent blocking when the O_NONBLOCK flag is set.
In addition, it is unnecessary to check for NULL on the iowarrior dev
structure obtained by reading file->private_data. Therefore, it is
better to remove the check.
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://lore.kernel.org/r/20240919103403.3986-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/usb to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a small window during probing when IO is running
but the backlight is not registered. Processing events
during that time will crash. The completion handler
needs to check for a backlight before scheduling work.
The bug is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240912123317.1026049-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb5744 supports SMBus Configuration and it may be configured via the
SMBus slave interface during the hub start-up configuration stage.
To program it driver uses i2c-bus phandle (added in commit '02be19e914b8
dt-bindings: usb: Add support for Microchip usb5744 hub controller') to
get i2c client device and then based on usb5744 compatible check calls
usb5744 i2c default initialization sequence.
Apart from the USB command attach, prevent the hub from suspend.
when the USB Attach with SMBus (0xAA56) command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBus access made by the SMBus Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.
Prevent the MCU from putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2
register at address 0x411D controls this aspect of the hub. The
BYPASS_UDC_SUSPEND bit in register 0x411Dh must be set to ensure that the
MCU is always enabled and ready to respond to SMBus runtime commands.
This register needs to be written before the USB attach command is issued.
The byte sequence is as follows:
Slave addr: 0x2d 00 00 05 00 01 41 1D 08
Slave addr: 0x2d 99 37 00
Slave addr: 0x2d AA 56 00
Also since usb5744 i2c initialization routine uses i2c SMBus APIs invoke
these APIs only when i2c driver is enabled in the kernel configuration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1725732196-70975-3-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce dedicated field 'power_on_delay_us' in onboard platform data
and update its delay for USB5744 configuration. Hub itself requires some
delay after reset to get to state where configuration data is going to
be accepted. Without delay upcoming support for configuration via SMBUS
is reporting a failure on the first SMBus write.
i2c 2-002d: error -ENXIO: BYPASS_UDC_SUSPEND bit configuration failed
Similar delay is likely also required for default configuration but
because there is enough time (code execution) between reset and usage
of the hub any issue is not visible but it doesn't mean delay shouldn't
be reflected.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1725732196-70975-2-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240822130113.164644-3-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add LJCA GPIO support for the Lunar Lake platform.
New HID taken from out of tree ivsc-driver git repo.
Link: 47e7c4a446
Cc: stable <stable@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240812095038.555837-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bindings require two compatibles to be used: qcom,sc7280-eud
followed by fallback qcom,eud. The convention is to use fallback
compatible in OF device ID tables, unless some device-specific quirks
are needed.
This will also simplify matching any new devices - they will use
existing OF device ID entry, instead of adding a new one.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240731054438.9073-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Add a match function for the onboard_usb_dev driver. Primary
matching is still done through the VID:PID pair, as usual for
USB devices. The new match function checks in addition whether
the device has a device tree node, which is a needed for using
the onboard_usb_dev driver.
Remove the check for a device tree node from _probe(), the new
match functions prevents devices without DT node from probing.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Jameson Thies <jthies@google.com>
Reviewed-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240612180448.1.I805556c176c626872c15ce001f0e8198e1f95ae1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240619194413.2544537-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/ezusb.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/isight_firmware.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/yurex.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-usb-misc-v1-1-98475a5aa8ef@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
interacting with "usb: misc: onboard_usb_hub: Disable the USB hub clock
on failure"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20240424161202.7e45e19e@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The incompatible device in my possession has a sticker that says
"F5U002 Rev 2" and "P80453-B", and lsusb identifies it as
"050d:0002 Belkin Components IEEE-1284 Controller". There is a bug
report from 2007 from Michael Trausch who was seeing the exact same
errors that I saw in 2024 trying to use this cable.
Link: https://lore.kernel.org/all/46DE5830.9060401@trausch.us/
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-5-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is a gray USB parallel port adapter with "F5U002" imprinted
on the plastic and a sticker that says both "F5U002" and "P80453-A".
It's identified in lsusb as "05ab:1001 In-System Design BAYI Printer
Class Support". It's subtly different from the other gray cable I have
that has "F5U002 Rev 2" and "P80453-B" on its sticker and device ID
050d:0002.
The uss720 driver appears to work flawlessly with this device, although
the device evidently does not support ECP.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-4-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids a "fix this legacy no-device port driver" warning from
parport_announce_port in drivers/parport/share.c. The parport driver now
requires a pointer to the device struct.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-2-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XMOS XVF3500 VocalFusion Voice Processor[1] is a low-latency, 32-bit
multicore controller for voice processing.
This device requires a specific power sequence, which consists of
enabling the regulators that control the 3V3 and 1V0 device supplies,
and a reset de-assertion after a delay of at least 100ns.
Once in normal operation, the XVF3500 registers itself as a USB device,
and it does not require any device-specific operations in the driver.
[1] https://www.xmos.com/xvf3500/
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-8-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the functionality this driver provides can be used by non-hub
devices as well.
To account for the hub-specific code, add a flag to the device data
structure and check its value for hub-specific code.
The 'always_powered_in_supend' attribute is only available for hub
devices, keeping the driver's default behavior for non-hub devices (keep
on in suspend).
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-6-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares onboad_hub to support non-hub devices by renaming
the driver files and their content, the headers and their references.
The comments and descriptions have been slightly modified to keep
coherence and account for the specific cases that only affect onboard
hubs (e.g. peer-hub).
The "hub" variables in functions where "dev" (and similar names) variables
already exist have been renamed to onboard_dev for clarity, which adds a
few lines in cases where more than 80 characters are used.
No new functionality has been added.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-2-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses generic names for the power supplies,
which conflicts with proper name definitions in the device bindings.
Add a per-device property to include real supply names and keep generic
names for existing devices to keep backward compatibility.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-1-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function ljca_auxdev_release
calls kfree(auxdev->dev.platform_data) to free the parameter data
of the function ljca_new_client_device. The callers of
ljca_new_client_device shouldn't call kfree() again
in the error handling path to free the platform data.
Fix this by cleaning up the redundant kfree() in all callers and
adding kfree() the passed in platform_data on errors which happen
before auxiliary_device_init() succeeds .
Fixes: acd6199f195d ("usb: Add support for Intel LJCA device")
Cc: stable <stable@kernel.org>
Signed-off-by: Yongzhi Liu <hyperlyzcs@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240311125748.28198-1-hyperlyzcs@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 14485de431b0 ("usb: Use device_get_match_data()") overlooked the
already existing pointer to pdev->dev 'dev'.
Use the existing pointer 'dev' in device_get_match_data() to keep code
consistency.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240305-onboard_xvf3500-v7-1-ad3fb50e593b@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI TUSB8020B is a 2-port USB 3.0 hub. Add support for
this hub in the driver in order to bring up reset, and supply
dependencies.
Power-up: Issue a GPIO reset (GRSTz) 3ms after VDD and VDD33 stabilize.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240227090228.22156-2-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Whilst we're at it, let's define some magic numbers to increase
readability and ease of maintenance.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-9-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C6563x is a 2/4-port USB 2.0 hub. Add support for
this hub in the driver in order to bring up reset, supply or clock
dependencies.
There is no reset pulse width given in the datasheet so we expect
a minimal value of 1us to be enough. This hasn't been tested though
due to lack of hardware which has the reset connected to a GPIO.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-3-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most onboard USB hubs have a dedicated crystal oscillator but on some
boards the clock signal for the hub is provided by the SoC.
In order to support this, we add the possibility of specifying a
clock in the devicetree that gets enabled/disabled when the hub
is powered up/down.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-2-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of printing the decimal error codes, let's use the more
human-readable symbolic error names provided by the %pe printk
format specifier.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-1-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB/PHY/Thunderbolt fixes in here as well for later patches
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
