linux-next/arch/arm/mach-pxa/mfp-pxa2xx.h
Arnd Bergmann 64dbc4dd7a ARM: pxa: move plat-pxa to drivers/soc/
There are two drivers in arch/arm/plat-pxa: mfp and ssp. Both
of them should ideally not be needed at all, as there are
proper subsystems to replace them.

OTOH, they are self-contained and can simply be normal
SoC drivers, so move them over there to eliminate one more
of the plat-* directories.

Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> (mach-pxa)
Acked-by: Lubomir Rintel <lkundrak@v3.sk> (mach-mmp)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-07 22:56:16 +02:00

144 lines
5.4 KiB
C

/* SPDX-License-Identifier: GPL-2.0 */
#ifndef __ASM_ARCH_MFP_PXA2XX_H
#define __ASM_ARCH_MFP_PXA2XX_H
#include <linux/soc/pxa/mfp.h>
/*
* the following MFP_xxx bit definitions in mfp.h are re-used for pxa2xx:
*
* MFP_PIN(x)
* MFP_AFx
* MFP_LPM_DRIVE_{LOW, HIGH}
* MFP_LPM_EDGE_x
*
* other MFP_x bit definitions will be ignored
*
* and adds the below two bits specifically for pxa2xx:
*
* bit 23 - Input/Output (PXA2xx specific)
* bit 24 - Wakeup Enable(PXA2xx specific)
* bit 25 - Keep Output (PXA2xx specific)
*/
#define MFP_DIR_IN (0x0 << 23)
#define MFP_DIR_OUT (0x1 << 23)
#define MFP_DIR_MASK (0x1 << 23)
#define MFP_DIR(x) (((x) >> 23) & 0x1)
#define MFP_LPM_CAN_WAKEUP (0x1 << 24)
/*
* MFP_LPM_KEEP_OUTPUT must be specified for pins that need to
* retain their last output level (low or high).
* Note: MFP_LPM_KEEP_OUTPUT has no effect on pins configured for input.
*/
#define MFP_LPM_KEEP_OUTPUT (0x1 << 25)
#define WAKEUP_ON_EDGE_RISE (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_RISE)
#define WAKEUP_ON_EDGE_FALL (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_FALL)
#define WAKEUP_ON_EDGE_BOTH (MFP_LPM_CAN_WAKEUP | MFP_LPM_EDGE_BOTH)
/* specifically for enabling wakeup on keypad GPIOs */
#define WAKEUP_ON_LEVEL_HIGH (MFP_LPM_CAN_WAKEUP)
#define MFP_CFG_IN(pin, af) \
((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK)) |\
(MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DIR_IN))
/* NOTE: pins configured as output _must_ provide a low power state,
* and this state should help to minimize the power dissipation.
*/
#define MFP_CFG_OUT(pin, af, state) \
((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK | MFP_LPM_STATE_MASK)) |\
(MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_DIR_OUT | MFP_LPM_##state))
/* Common configurations for pxa25x and pxa27x
*
* Note: pins configured as GPIO are always initialized to input
* so not to cause any side effect
*/
#define GPIO0_GPIO MFP_CFG_IN(GPIO0, AF0)
#define GPIO1_GPIO MFP_CFG_IN(GPIO1, AF0)
#define GPIO9_GPIO MFP_CFG_IN(GPIO9, AF0)
#define GPIO10_GPIO MFP_CFG_IN(GPIO10, AF0)
#define GPIO11_GPIO MFP_CFG_IN(GPIO11, AF0)
#define GPIO12_GPIO MFP_CFG_IN(GPIO12, AF0)
#define GPIO13_GPIO MFP_CFG_IN(GPIO13, AF0)
#define GPIO14_GPIO MFP_CFG_IN(GPIO14, AF0)
#define GPIO15_GPIO MFP_CFG_IN(GPIO15, AF0)
#define GPIO16_GPIO MFP_CFG_IN(GPIO16, AF0)
#define GPIO17_GPIO MFP_CFG_IN(GPIO17, AF0)
#define GPIO18_GPIO MFP_CFG_IN(GPIO18, AF0)
#define GPIO19_GPIO MFP_CFG_IN(GPIO19, AF0)
#define GPIO20_GPIO MFP_CFG_IN(GPIO20, AF0)
#define GPIO21_GPIO MFP_CFG_IN(GPIO21, AF0)
#define GPIO22_GPIO MFP_CFG_IN(GPIO22, AF0)
#define GPIO23_GPIO MFP_CFG_IN(GPIO23, AF0)
#define GPIO24_GPIO MFP_CFG_IN(GPIO24, AF0)
#define GPIO25_GPIO MFP_CFG_IN(GPIO25, AF0)
#define GPIO26_GPIO MFP_CFG_IN(GPIO26, AF0)
#define GPIO27_GPIO MFP_CFG_IN(GPIO27, AF0)
#define GPIO28_GPIO MFP_CFG_IN(GPIO28, AF0)
#define GPIO29_GPIO MFP_CFG_IN(GPIO29, AF0)
#define GPIO30_GPIO MFP_CFG_IN(GPIO30, AF0)
#define GPIO31_GPIO MFP_CFG_IN(GPIO31, AF0)
#define GPIO32_GPIO MFP_CFG_IN(GPIO32, AF0)
#define GPIO33_GPIO MFP_CFG_IN(GPIO33, AF0)
#define GPIO34_GPIO MFP_CFG_IN(GPIO34, AF0)
#define GPIO35_GPIO MFP_CFG_IN(GPIO35, AF0)
#define GPIO36_GPIO MFP_CFG_IN(GPIO36, AF0)
#define GPIO37_GPIO MFP_CFG_IN(GPIO37, AF0)
#define GPIO38_GPIO MFP_CFG_IN(GPIO38, AF0)
#define GPIO39_GPIO MFP_CFG_IN(GPIO39, AF0)
#define GPIO40_GPIO MFP_CFG_IN(GPIO40, AF0)
#define GPIO41_GPIO MFP_CFG_IN(GPIO41, AF0)
#define GPIO42_GPIO MFP_CFG_IN(GPIO42, AF0)
#define GPIO43_GPIO MFP_CFG_IN(GPIO43, AF0)
#define GPIO44_GPIO MFP_CFG_IN(GPIO44, AF0)
#define GPIO45_GPIO MFP_CFG_IN(GPIO45, AF0)
#define GPIO46_GPIO MFP_CFG_IN(GPIO46, AF0)
#define GPIO47_GPIO MFP_CFG_IN(GPIO47, AF0)
#define GPIO48_GPIO MFP_CFG_IN(GPIO48, AF0)
#define GPIO49_GPIO MFP_CFG_IN(GPIO49, AF0)
#define GPIO50_GPIO MFP_CFG_IN(GPIO50, AF0)
#define GPIO51_GPIO MFP_CFG_IN(GPIO51, AF0)
#define GPIO52_GPIO MFP_CFG_IN(GPIO52, AF0)
#define GPIO53_GPIO MFP_CFG_IN(GPIO53, AF0)
#define GPIO54_GPIO MFP_CFG_IN(GPIO54, AF0)
#define GPIO55_GPIO MFP_CFG_IN(GPIO55, AF0)
#define GPIO56_GPIO MFP_CFG_IN(GPIO56, AF0)
#define GPIO57_GPIO MFP_CFG_IN(GPIO57, AF0)
#define GPIO58_GPIO MFP_CFG_IN(GPIO58, AF0)
#define GPIO59_GPIO MFP_CFG_IN(GPIO59, AF0)
#define GPIO60_GPIO MFP_CFG_IN(GPIO60, AF0)
#define GPIO61_GPIO MFP_CFG_IN(GPIO61, AF0)
#define GPIO62_GPIO MFP_CFG_IN(GPIO62, AF0)
#define GPIO63_GPIO MFP_CFG_IN(GPIO63, AF0)
#define GPIO64_GPIO MFP_CFG_IN(GPIO64, AF0)
#define GPIO65_GPIO MFP_CFG_IN(GPIO65, AF0)
#define GPIO66_GPIO MFP_CFG_IN(GPIO66, AF0)
#define GPIO67_GPIO MFP_CFG_IN(GPIO67, AF0)
#define GPIO68_GPIO MFP_CFG_IN(GPIO68, AF0)
#define GPIO69_GPIO MFP_CFG_IN(GPIO69, AF0)
#define GPIO70_GPIO MFP_CFG_IN(GPIO70, AF0)
#define GPIO71_GPIO MFP_CFG_IN(GPIO71, AF0)
#define GPIO72_GPIO MFP_CFG_IN(GPIO72, AF0)
#define GPIO73_GPIO MFP_CFG_IN(GPIO73, AF0)
#define GPIO74_GPIO MFP_CFG_IN(GPIO74, AF0)
#define GPIO75_GPIO MFP_CFG_IN(GPIO75, AF0)
#define GPIO76_GPIO MFP_CFG_IN(GPIO76, AF0)
#define GPIO77_GPIO MFP_CFG_IN(GPIO77, AF0)
#define GPIO78_GPIO MFP_CFG_IN(GPIO78, AF0)
#define GPIO79_GPIO MFP_CFG_IN(GPIO79, AF0)
#define GPIO80_GPIO MFP_CFG_IN(GPIO80, AF0)
#define GPIO81_GPIO MFP_CFG_IN(GPIO81, AF0)
#define GPIO82_GPIO MFP_CFG_IN(GPIO82, AF0)
#define GPIO83_GPIO MFP_CFG_IN(GPIO83, AF0)
#define GPIO84_GPIO MFP_CFG_IN(GPIO84, AF0)
extern void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num);
extern void pxa2xx_mfp_set_lpm(int mfp, unsigned long lpm);
extern int gpio_set_wake(unsigned int gpio, unsigned int on);
#endif /* __ASM_ARCH_MFP_PXA2XX_H */