commit 7aae51347b21eb738dc1981df1365b57a6c5ee4e upstream.
Evidently some wacky USB-ATA bridges don't recognize the SYNCHRONIZE
CACHE command, as shown in this email thread:
http://marc.info/?t=138978356200002&r=1&w=2
The fact that we can't tell them to drain their caches shouldn't
prevent the system from going into suspend. Therefore sd_sync_cache()
shouldn't return an error if the device replies with an Invalid
Command ASC.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c3f68f3cd8d55f809fbdb0c138ed061ea1bd25 upstream.
The user-settable knob, low_latency, has been the source of
several BUG reports which stem from flush_to_ldisc() running
in interrupt context. Since 3.12, which added several sleeping
locks (termios_rwsem and buf->lock) to the input processing path,
the frequency of these BUG reports has increased.
Note that changes in 3.12 did not introduce this regression;
sleeping locks were first added to the input processing path
with the removal of the BKL from N_TTY in commit
a88a69c91256418c5907c2f1f8a0ec0a36f9e6cc,
'n_tty: Fix loss of echoed characters and remove bkl from n_tty'
and later in commit 38db89799bdf11625a831c5af33938dcb11908b6,
'tty: throttling race fix'. Since those changes, executing
flush_to_ldisc() in interrupt_context (ie, low_latency set), is unsafe.
However, since most devices do not validate if the low_latency
setting is appropriate for the context (process or interrupt) in
which they receive data, some reports are due to misconfiguration.
Further, serial dma devices for which dma fails, resort to
interrupt receiving as a backup without resetting low_latency.
Historically, low_latency was used to force wake-up the reading
process rather than wait for the next scheduler tick. The
effect was to trim multiple milliseconds of latency from
when the process would receive new data.
Recent tests [1] have shown that the reading process now receives
data with only 10's of microseconds latency without low_latency set.
Remove the low_latency rx steering from tty_flip_buffer_push();
however, leave the knob as an optional hint to drivers that can
tune their rx fifos and such like. Cleanup stale code comments
regarding low_latency.
[1] https://lkml.org/lkml/2014/2/20/434
"Yay.. thats an annoying historical pain in the butt gone."
-- Alan Cox
Reported-by: Beat Bolli <bbolli@ewanet.ch>
Reported-by: Pavel Roskin <proski@gnu.org>
Acked-by: David Sterba <dsterba@suse.cz>
Cc: Grant Edwards <grant.b.edwards@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Hal Murray <murray+fedora@ip-64-139-1-69.sjc.megapath.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 723abd87f6e536f1353c8f64f621520bc29523a3 upstream.
The 'active' sysfs attribute should refer to the currently active tty
devices the console is running on, not the currently active console. The
console structure doesn't refer to any device in sysfs, only the tty the
console is running on has. So we need to print out the tty names in
'active', not the console names.
There is one special-case, which is tty0. If the console is directed to
it, we want 'tty0' to show up in the file, so user-space knows that the
messages get forwarded to the active VT. The ->device() callback would
resolve tty0, though. Hence, treat it special and don't call into the VT
layer to resolve it (plymouth is known to depend on it).
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Werner Fink <werner@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 268d1e799663b795cba15c64f5d29407786a9dd4 upstream.
According to National Instruments' PCI-DIO-96/PXI-6508/PCI-6503 User
Manual, the physical address in PCI BAR1 needs to be OR'ed with 0x80 and
written to register offset 0xC0 in the "MITE" registers (BAR0). Do so
during initialization of the National Instruments boards handled by the
"8255_pci" driver. The boards were previously handled by the
"ni_pcidio" driver, where the initialization was done by `mite_setup()`
in the "mite" module. The "mite" module comes with too much extra
baggage for the "8255_pci" driver to deal with so use a local, simpler
initialization function.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 866d54177b4e671cd52bed1fb487d140d7b691f5 upstream.
Andreas reported that after 1f42db786b14 ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.
This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.
Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device(). But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.
This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.
Fixes: 1f42db786b14 PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691
Reported-and-tested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bf6368ee8f25826d0645c0f7a4f17c8845356a4 upstream.
Commit 1696d9d (ACPI: Remove the old /proc/acpi/event interface)
removed ACPI Button event which originally was sent to userspace via
/proc/acpi/event. This caused ACPI shutdown regression on gentoo
in VirtualBox. Now ACPI events are sent to userspace via netlink,
so add ACPI Button event back via netlink routine.
References: https://bugzilla.kernel.org/show_bug.cgi?id=71721
Reported-and-tested-by: Richard Musil <richard.musil@gmail.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 017fcdc30cdae18c0946eef1ece1f14b4c7897ba upstream.
This patch corrects iATU programming for cfg1, io and mem viewport. Enable
ATU only after configuring it.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Ajay Khandelwal <ajay.khandelwal@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbffdd6862e67d60703f2df66c558bf448f81d6e upstream.
The Synopsys PCIe core provides one pair of 32-bit BARs (BAR 0 and BAR 1).
The BARs can be configured as follows:
- One 64-bit BAR: BARs 0 and 1 are combined to form a single 64-bit BAR
- Two 32-bit BARs: BARs 0 and 1 are two independent 32-bit BARs
This patch corrects 64-bit, non-prefetchable memory BAR configuration
implemented in dw driver.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a94cdd1f4d30f12904ab528152731fb13a812a16 upstream.
In read_all_bytes, we do
unsigned char i;
...
bt->read_data[0] = BMC2HOST;
bt->read_count = bt->read_data[0];
...
for (i = 1; i <= bt->read_count; i++)
bt->read_data[i] = BMC2HOST;
If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-debugged-by: Rui Hui Dian <rhdian@novell.com>
Cc: Tomas Cech <tcech@suse.cz>
Cc: Corey Minyard <minyard@acm.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22c73795b101597051924556dce019385a1e2fa0 upstream.
This patch reorders reported frequencies from the highest to the lowest,
just like in other frequency drivers.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d82b922a4acc1781d368aceac2f9da43b038cab2 upstream.
The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:
* If there was a frequency transition before, the multiplier read from the
register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
register always reads as zero, regardless of the current multiplier that
is set using switches on the mainboard and that the CPU is running at.
The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.
For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.
There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e20e1d0ac02308e2211306fc67abcd0b2668fb8b upstream.
I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.
During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.
This patch flushes the cache during frequency transition. It fixes the
instability.
Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
powernow_k6_set_cpu_multiplier
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
open during other activity (running other kernel code with the port open
shouldn't cause any misbehavior, but we should better be safe and keep
the port closed)
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7563487cbf865284dcd35e9ef5a95380da046737 ]
There are three buffer overflows addressed in this patch.
1) In isdnloop_fake_err() we add an 'E' to a 60 character string and
then copy it into a 60 character buffer. I have made the destination
buffer 64 characters and I'm changed the sprintf() to a snprintf().
2) In isdnloop_parse_cmd(), p points to a 6 characters into a 60
character buffer so we have 54 characters. The ->eazlist[] is 11
characters long. I have modified the code to return if the source
buffer is too long.
3) In isdnloop_command() the cbuf[] array was 60 characters long but the
max length of the string then can be up to 79 characters. I made the
cbuf array 80 characters long and changed the sprintf() to snprintf().
I also removed the temporary "dial" buffer and changed it to use "p"
directly.
Unfortunately, we pass the "cbuf" string from isdnloop_command() to
isdnloop_writecmd() which truncates anything over 60 characters to make
it fit in card->omsg[]. (It can accept values up to 255 characters so
long as there is a '\n' character every 60 characters). For now I have
just fixed the memory corruption bug and left the other problems in this
driver alone.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77bc6bed7121936bb2e019a8c336075f4c8eef62 ]
Return -EINVAL unless all of user-given strings are correctly
NUL-terminated.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52ad762b85ed7947ec9eff6b036eb985352f6874 ]
When using the "separate_tx_channels=1" module parameter, the TX queues are
initially numbered starting from the first TX-only channel number (after all the
RX-only channels). efx_set_channels() renumbers the queues so that they are
indexed from zero.
On EF10, the TX queues need to be relabelled in this way before calling the
dimension_resources NIC type operation, otherwise the TX queue PIO buffers can be
linked to the wrong VIs when using "separate_tx_channels=1".
Added comments to explain UC/WC mappings for PIO buffers
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9d8b2c2968499c1f96563e6522c56958d5a1d0d ]
When netback discovers frontend is sending malformed packet it will
disables the interface which serves that frontend.
However disabling a network interface involving taking a mutex which
cannot be done in softirq context, so we need to defer this process to
kthread context.
This patch does the following:
1. introduce a flag to indicate the interface is disabled.
2. check that flag in TX path, don't do any work if it's true.
3. check that flag in RX path, turn off that interface if it's true.
The reason to disable it in RX path is because RX uses kthread. After
this change the behavior of netback is still consistent -- it won't do
any TX work for a rogue frontend, and the interface will be eventually
turned off.
Also change a "continue" to "break" after xenvif_fatal_tx_err, as it
doesn't make sense to continue processing packets if frontend is rogue.
This is a fix for XSA-90.
Reported-by: Török Edwin <edwin@etorok.net>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0576eddf24df716d8570ef8ca11452a9f98eaab2 ]
This patch removes a test in start_new_rx_buffer() that checks whether
a copy operation is less than MAX_BUFFER_OFFSET in length, since
MAX_BUFFER_OFFSET is defined to be PAGE_SIZE and the only caller of
start_new_rx_buffer() already limits copy operations to PAGE_SIZE or less.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Reported-By: Sander Eikelenboom <linux@eikelenboom.it>
Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a39ee449f96a2cd44ce056d8a0a112211a9b1a1f ]
vhost fails to validate negative error code
from vhost_get_vq_desc causing
a crash: we are using -EFAULT which is 0xfffffff2
as vector size, which exceeds the allocated size.
The code in question was introduced in commit
8dd014adfea6f173c1ef6378f7e5e7924866c923
vhost-net: mergeable buffers support
CVE-2014-0055
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8316f3991d207fe32881a9ac20241be8fa2bad0 ]
When mergeable buffers are disabled, and the
incoming packet is too large for the rx buffer,
get_rx_bufs returns success.
This was intentional in order for make recvmsg
truncate the packet and then handle_rx would
detect err != sock_len and drop it.
Unfortunately we pass the original sock_len to
recvmsg - which means we use parts of iov not fully
validated.
Fix this up by detecting this overrun and doing packet drop
immediately.
CVE-2014-0077
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14a0d635d18d0fb552dcc979d6d25106e6541f2e ]
This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().
The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 681daee2443291419c57cccb0671f5f94a839005 ]
Current error handling of virtqueue_kick() was wrong in two places:
- The skb were freed immediately when virtqueue_kick() fail during
xmit. This may lead double free since the skb was not detached from
the virtqueue.
- try_fill_recv() returns false when virtqueue_kick() fail. This will
lead unnecessary rescheduling of refill work.
Actually, it's safe to just ignore the kick failure in those two
places. So this patch fixes this by partially revert commit
67975901183799af8e93ec60e322f9e2a1940b9b.
Fixes 67975901183799af8e93ec60e322f9e2a1940b9b
(virtio_net: verify if virtqueue_kick() succeeded).
Cc: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51dfe7b944998eaeb2b34d314f3a6b16a5fd621b ]
Including hardware acceleration features in vlan_features breaks
stacked vlans (Q-in-Q) by marking the bottom vlan interface as
capable of acceleration. This causes one of the tags to be lost
and the packets are sent with a sing vlan header.
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebf4ad955d3e26d4d2a33709624fc7b5b9d3b969 ]
Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.
Fixes: 66fda75f47dc (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b29dba9c085a4fb79058fb1c45a2f6257ca3dfa ]
The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:
1) The original code drops all packets with a multicast destination address,
even though neighbor solicitations are sent to the solicited-node
address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
solicited node address, rather than the target address from the
neighbor solicitation. So neighbor lookups would always fail if it
got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
The context for neigh_reduce() is the transmit path, vxlan_xmit(),
where the host or a bridge-attached neighbor is trying to transmit
a neighbor solicitation. To respond to it, the tunnel endpoint needs
to do a *receive* of the appropriate neighbor advertisement. Doing a
send, would only try to send the advertisement, encapsulated, to the
remote destinations in the fdb -- hosts that definitely did not do the
corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
isrouter flag in the advertisement. This has nothing to do with whether
or not the target is a router, and generally won't be set since the
tunnel endpoint is bridging, not routing, traffic.
The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7346135dcd3f9b57f30a5512094848c678d7143e ]
This patch fixes a NULL pointer dereference in the event of an
skb allocation failure in arp_reduce().
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff0992e9036e9810e7cd45234fa32ca1e79750e2 ]
This is a context modified revert of commit 6a9612e2cb22
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb22 ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84fe61821e4ebab6322eeae3f3c27f77f0031978 ]
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb00bc2e6cd2046282ba4b03f4fe682aee70b2f8 ]
The commit d3ab3ffd1d728d7ee77340e7e7e2c7cfe6a4013e
(bonding: use rlb_client_info->vlan_id instead of ->tag)
remove the rlb_client_info->tag, but occur some issues,
The vlan_get_tag() will return 0 for success and -EINVAL for
error, so the client_info->vlan_id always be set to 0 if the
vlan_get_tag return 0 for success, so the client_info would
never get a correct vlan id.
We should only set the vlan id to 0 when the vlan_get_tag return error.
Fixes: d3ab3ffd1d7 (bonding: use rlb_client_info->vlan_id instead of ->tag)
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5bd076708664313f2bdbbc1cf71093313b7774a1 ]
Current netback uses gso_type to check whether the skb contains
gso offload, and this is wrong. Gso_size is the right one to
check gso existence, and gso_type is only used to check gso type.
Some skbs contains nonzero gso_type and zero gso_size, current
netback would treat these skbs as gso and create wrong response
for this. This also causes ssh failure to domu from other server.
V2: use skb_is_gso function as Paul Durrant suggested
Signed-off-by: Annie Li <annie.li@oracle.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8d9bc2e9f5d1c5a25e33cec096d2a1652d3fd52 ]
The pci shutdown handler added in:
bnx2: Add pci shutdown handler
commit 25bfb1dd4ba3b2d9a49ce9d9b0cd7be1840e15ed
created a shutdown down sequence without chip reset if the device was
never brought up. This can cause the firmware to shutdown the PHY
prematurely and cause MMIO read cycles to be unresponsive. On some
systems, it may generate NMI in the bnx2's pci shutdown handler.
The fix is to tell the firmware not to shutdown the PHY if there was
no prior chip reset.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 668f9abbd4334e6c29fa8acd71635c4f9101caa7 upstream.
Commit bf6bddf1924e ("mm: introduce compaction and migration for
ballooned pages") introduces page_count(page) into memory compaction
which dereferences page->first_page if PageTail(page).
This results in a very rare NULL pointer dereference on the
aforementioned page_count(page). Indeed, anything that does
compound_head(), including page_count() is susceptible to racing with
prep_compound_page() and seeing a NULL or dangling page->first_page
pointer.
This patch uses Andrea's implementation of compound_trans_head() that
deals with such a race and makes it the default compound_head()
implementation. This includes a read memory barrier that ensures that
if PageTail(head) is true that we return a head page that is neither
NULL nor dangling. The patch then adds a store memory barrier to
prep_compound_page() to ensure page->first_page is set.
This is the safest way to ensure we see the head page that we are
expecting, PageTail(page) is already in the unlikely() path and the
memory barriers are unfortunately required.
Hugetlbfs is the exception, we don't enforce a store memory barrier
during init since no race is possible.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Holger Kiehl <Holger.Kiehl@dwd.de>
Cc: Christoph Lameter <cl@linux.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3a8786c10e75903f1269474e21fe8cb49c3a670 upstream.
Commit 5445eaf309ff ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.
However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.
Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.
In detail, to achieve this, the commit:
* Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
not specific to SGMII, but also used on RGMII configurations.
* Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
the MVNETA_SERDES_CFG value in RGMII configurations.
* Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
functions, and instead directly do the SGMII/RGMII configuration in
mvneta_port_up(), from where those functions where called. It is
worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
parameter that was always passed as '1', so it was pretty useless.
* Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
register to the appropriate value depending on the RGMII vs. SGMII
configuration. It also unconditionally set the PCS_ENABLE bit (was
already done for SGMII, but is now also needed for RGMII), and sets
the PORT_RGMII bit (which was already done for both SGMII and
RGMII).
This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).
Reported-by: Steve McIntyre <steve@einval.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a79121d3b57e7ad61f0b5d23eae05214054f3ccd upstream.
Bit 3 of the MVNETA_GMAC_CTRL_2 is actually used to enable the PCS,
not the PSC: there was a typo in the name of the define, which this
commit fixes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f12c5eca6e6b7aeb4b2028d579f614b4fe7a81f upstream.
Fixes a build break due to the undeclared use of irq_of_parse_and_map()
and of_iomap(). This build break was apparently introduced while the
driver was unbuildable due to the bug fixed by
62c19c9d29e65086e5ae76df371ed2e6b23f00cd ("i2c: Remove usage of
orphaned symbol OF_I2C"). When 62c19c was added in v3.14-rc7,
the driver was enabled again, breaking the powerpc mpc85xx_defconfig
and mpc85xx_smp_defconfig.
62c19c is marked for stable, so this should go there as well.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09ed3d5ba06137913960f9c9385f71fc384193ab upstream.
Xen balloon driver will update ballooned out pages' P2M entries to point
to scratch page for PV guests. In 24f69373e2 ("xen/balloon: don't alloc
page while non-preemptible", kmap_flush_unused was moved after updating
P2M table. In that case for 32 bit PV guest we might end up with
P2M X -----> S (S is mfn of balloon scratch page)
M2P Y -----> X (Y is mfn in persistent kmap entry)
kmap_flush_unused() iterates through all the PTEs in the kmap address
space, using pte_to_page() to obtain the page. If the p2m and the m2p
are inconsistent the incorrect page is returned. This will clear
page->address on the wrong page which may cause subsequent oopses if
that page is currently kmap'ed.
Move the flush back between get_page and __set_phys_to_machine to fix
this.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6797b39e6f6f34c74177736e146406e894b9482b upstream.
The cypress PS/2 trackpad models supported by the cypress_ps2 driver
emulate BTN_RIGHT events in firmware based on the finger position, as part
of this no motion events are sent when the finger is in the button area.
The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that
BTN_RIGHT events should be emulated in userspace, which is not necessary
in this case.
When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion
event before propagating the button event higher up the stack, as it needs
current abs x + y data for its BTN_RIGHT emulation. Since in the
cypress_ps2 pads don't report motion events in the button area, this means
that clicks in the button area end up being ignored, so
INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and
removing it fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=76341
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0435d958fb36d93b8df610124a0e91e5675c82 upstream.
This extends Benjamin Tissoires manual min/max quirk table with support for
the ThinkPad X240.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 421e08c41fda1f0c2ff6af81a67b491389b653a5 upstream.
The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.
Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.
We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).
So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4dbedc7eac7da9db363a36f2bd4366962eeefcc upstream.
We should not be using static variable mousedev_mix in methods that can be
called before that singleton gets assigned. While at it let's add open and
close methods to mousedev structure so that we do not need to test if we
are dealing with multiplexor or normal device and simply call appropriate
method directly.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=71551
Reported-by: GiulioDP <depasquale.giulio@gmail.com>
Tested-by: GiulioDP <depasquale.giulio@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1aa9578c1a9450fb21501c4f549f5b1edb557e6d upstream.
Don Zickus <dzickus@redhat.com> writes:
Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail). This led to frustration as suspend/resume is a common use for
laptops.
Poking around, I applied the reset on resume quirk to this chipset and the
resume started working. Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 961794a00eab03f4344b7d5e825e8e789e55da87 upstream.
New Intuos series models added a hardware switch to turn touch
data on/off. The state of the switch is reported periodically
from the tablet. To report the state the driver will emit SW_MUTE_DEVICE
events.
Reviewed_by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5fd2a3e92ca5c8c1f3c20d31ac5daed3ec4d604 upstream.
Two tablets in this series support both pen and touch. One (Intuos S)
only supports pen. This patch also updates the driver to process wireless
devices that do not support touch interface.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d0d6df02750b4a6f466768cbfbf860e24f4c8d4 upstream.
Old single touch Tablet PCs do not have touch_max set at
wacom_features. Since touch device at lease supports one
finger, assign touch_max to 1 when touch usage is defined
in its HID Descriptor and touch_max is not pre-defined.
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c15bdfd5b9831e4cab8cfc118243956e267dd30e upstream.
The current assumption in the elantech driver that hw version 3 touchpads
are never clickpads and hw version 4 touchpads are always clickpads is
wrong.
There are several bug reports for this, ie:
https://bugzilla.redhat.com/show_bug.cgi?id=1030802http://superuser.com/questions/619582/right-elantech-touchpad-button-not-working-in-linux
I've spend a couple of hours wading through various bugzillas, launchpads
and forum posts to create a list of fw-versions and capabilities for
different laptop models to find a good method to differentiate between
clickpads and versions with separate hardware buttons.
Which shows that a device being a clickpad is reliable indicated by bit 12
being set in the fw_version. I've included the gathered list inside the
driver, so that we've this info at hand if we need to revisit this later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66fda75f47dc583f1c187556e9a2c082dd64f8c6 upstream.
There are many places where ops->disable is called directly. Instead we
should use _regulator_do_disable() which also handles gpio regulators.
To be able to use the wrapper function from _regulator_force_disable(),
I moved the _notifier_call_chain() call from _regulator_do_disable() to
_regulator_disable(). This way, _regulator_force_disable() can use
different flags for _notifier_call_chain() without calling it twice.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 608cfbe4abaf76e9d732efd7ed1cfa3998163d91 upstream.
The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef1d ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e83b366487b5582274374f8226e489cb214ae5a6 upstream.
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6ac ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd982 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
