commit efb9e0f4f43780f0ae0c6428d66bd03e805c7539 upstream.
Without the patch the kernel generates the following error.
ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123'
ata11.15: PMP revalidation failed (errno=-19)
ata11.15: failed to recover PMP after 5 tries, giving up
This patch helps to bypass this error and the device becomes
functional.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67809f85d31eac600f6b28defa5386c9d2a13b1d upstream.
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07b0e5b10258b48e5edfb6c8ac156f05510eb775 upstream.
Currently the I2C device Ids conflict for the MFD and CODEC so
cannot be both instantiated on one platform. This patch updates
the Ids and names to make them unique from each other.
It should be noted that the I2C addresses for both PMIC and CODEC
are modifiable so instantiation of the two are kept as separate
devices, rather than instantiating the CODEC from the MFD code.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71f6d1b31fb1f278a345a30a2180515adc7d80ae ]
Right now the mvneta driver doesn't handle Tx IRQ, and relies on two
mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx()
and a timer. If a burst of packets is emitted faster than the device
can send them, then the queue is stopped until next wake-up of the
timer 10ms later. This causes jerky output traffic with bursts and
pauses, making it difficult to reach line rate with very few streams.
A test on UDP traffic shows that it's not possible to go beyond 134
Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed
traffic tends to observe pauses as well if the traffic is bursty,
making it even burstier after the wake-up.
It seems that this feature was inherited from the original driver but
nothing there mentions any reason for not using the interrupt instead,
which the chip supports.
Thus, this patch enables Tx interrupts and removes the timer. It does
the two at once because it's not really possible to make the two
mechanisms coexist, so a split patch doesn't make sense.
First tests performed on a Mirabox (Armada 370) show that less CPU
seems to be used when sending traffic. One reason might be that we now
call the mvneta_tx_done_gbe() with a mask indicating which queues have
been done instead of looping over all of them.
The same UDP test above now happily reaches 987 Mbps / 87.7 kpps.
Single-stream TCP traffic can now more easily reach line rate. HTTP
transfers of 1 MB objects over a single connection went from 730 to
840 Mbps. It is even possible to go significantly higher (>900 Mbps)
by tweaking tcp_tso_win_divisor.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40ba35e74fa56866918d2f3bc0528b5b92725d5e ]
Marvell has not published the chip's datasheet yet, so it's very hard
to find the relevant bits to manipulate to change the IRQ behaviour.
Fortunately, these bits are described in the proprietary LSP patch set
which is publicly available here :
http://www.plugcomputer.org/downloads/mirabox/
So let's put them back in the driver in order to reduce the burden of
current and future maintenance.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 290213667ab53a95456397763205e4b1e30f46b5 ]
If a queue timeout is reported, we can oops because of some
schedules while the caller is atomic, as shown below :
mvneta d0070000.ethernet eth0: tx timeout
BUG: scheduling while atomic: bash/1528/0x00000100
Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv]
CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180
[<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc)
[<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64)
[<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c)
[<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec)
[<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118)
[<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14)
[<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194)
[<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24)
[<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4)
[<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c)
[<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170)
[<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8)
[<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98)
[<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60)
[<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8)
[<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60)
Ben Hutchings attempted to propose a better fix consisting in using a
scheduled work for this, but while it fixed this panic, it caused other
random freezes and panics proving that the reset sequence in the driver
is unreliable and that additional fixes should be investigated.
When sending multiple streams over a link limited to 100 Mbps, Tx timeouts
happen from time to time, and the driver correctly recovers only when the
function is disabled.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74c41b048db1073a04827d7f39e95ac1935524cc ]
Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything
when they update the stats, and as a result, it randomly happens that
the stats freeze on SMP if two updates happen during stats retrieval.
This is very easily reproducible by starting two HTTP servers and binding
each of them to a different CPU, then consulting /proc/net/dev in loops
during transfers, the interface should immediately lock up. This issue
also randomly happens upon link state changes during transfers, because
the stats are collected in this situation, but it takes more attempts to
reproduce it.
The comments in netdevice.h suggest using per_cpu stats instead to get
rid of this issue.
This patch implements this. It merges both rx_stats and tx_stats into
a single "stats" member with a single syncp. Both mvneta_rx() and
mvneta_rx() now only update the a single CPU's counters.
In turn, mvneta_get_stats64() does the summing by iterating over all CPUs
to get their respective stats.
With this change, stats are still correct and no more lockup is encountered.
Note that this bug was present since the first import of the mvneta
driver. It might make sense to backport it to some stable trees. If
so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats
out of the hot path".
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dc4277dd41a80fd5f29a90412ea04bc3ba54fbf1 ]
Better count packets and bytes in the stack and on 32 bit then
accumulate them at the end for once. This saves two memory writes
and two memory barriers per packet. The incoming packet rate was
increased by 4.7% on the Openblocks AX3 thanks to this.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 163c8ff30dbe473abfbb24a7eac5536c87f3baa9 ]
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb85569fe2d06c2fbf4de7b66c263ca095b397aa ]
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d43ff4cd798911736fb39025ec8004284b1b0bc2 ]
The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 891de74d693bb4fefe2efcc6432a4a9a9bee561e ]
Without this patch, the "cat /sys/class/net/ethN/operstate" shows
"unknown", and "ethtool ethN" shows "Link detected: yes", when VM
boots up with or without vNIC connected.
This patch fixed the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ad8b480d6ee916aa84324f69acf690142aecd0e ]
vhost checked the counter within the refcnt before decrementing. It
really wanted to know that it is the one that has the last reference, as
a way to batch freeing resources a bit more efficiently.
Note: we only let refcount go to 0 on device release.
This works well but we now access the ref counter twice so there's a
race: all users might see a high count and decide to defer freeing
resources.
In the end no one initiates freeing resources until the last reference
is gone (which is on VM shotdown so might happen after a looooong time).
Let's do what we probably should have done straight away:
switch from kref to plain atomic, documenting the
semantics, return the refcount value atomically after decrement,
then use that to avoid the deadlock.
Reported-by: Qin Chuanyu <qinchuanyu@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6993dfd7db9b0c6b7ca7503a56fda9236a4710f ]
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbd3a77d813f211060f86cc7a2f8416caf0e03b1 ]
This device was mentioned in an OpenWRT forum. Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
0: qcdm
2: nmea
3: modem
8: qmi
9: storage
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ae89beb283a0db5980d1d4781c7d7be2f2810d6 ]
Self generated skbuffs in net/can/bcm.c are setting a skb->sk reference but
no explicit destructor which is enforced since Linux 3.11 with commit
376c7311bdb6 (net: add a temporary sanity check in skb_orphan()).
This patch adds some helper functions to make sure that a destructor is
properly defined when a sock reference is assigned to a CAN related skb.
To create an unshared skb owned by the original sock a common helper function
has been introduced to replace open coded functions to create CAN echo skbs.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Andre Naujoks <nautsch2@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 upstream.
rtl8192ce is disabling for too long the local interrupts during hw initiatialisation when performing scans
The observable symptoms in dmesg can be:
- underruns from ALSA playback
- clock freezes (tstamps do not change for several dmesg entries until irqs are finaly reenabled):
[ 250.817669] rtlwifi:rtl_op_config():<0-0-0> 0x100
[ 250.817685] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-1-0> IPS Set eRf nic enable
[ 250.817732] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817796] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817910] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818024] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818139] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818253] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818367] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:98053f15:10
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtl8192c_common:rtl92c_download_fw():<0-1-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> The SECR-value cc
[ 250.818472] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-1-0> Schedule TxPowerTracking direct call!!
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> rtl92c_dm_txpower_tracking_callback_thermalmeter
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial pathA ele_d reg0xc80 = 0x40000000, ofdm_index=0xc
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial reg0xa24 = 0x90e1317, cck_index=0xc, ch14 0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf delta 0x1 delta_lck 0x0 delta_iqk 0x0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> <===
[ 250.818472] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-1-0> pMgntInfo->txpower_tracking = 1
[ 250.818472] rtl8192ce:rtl92ce_led_control():<0-1-0> ledaction 3
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtlwifi:rtl_ips_nic_on():<0-1-0> before spin_unlock_irqrestore
[ 251.154656] PCM: Lost interrupts? [Q]-0 (stream=0, delta=15903, new_hw_ptr=293408, old_hw_ptr=277505)
The exact code flow that causes that is:
1. wpa_supplicant send a start_scan request to the nl80211 driver
2. mac80211 module call rtl_op_config with IEEE80211_CONF_CHANGE_IDLE
3. rtl_ips_nic_on is called which disable local irqs
4. rtl92c_phy_set_rf_power_state() is called
5. rtl_ps_enable_nic() is called and hw_init()is executed and then the interrupts on the device are enabled
A good solution could be to refactor the code to avoid calling rtl92ce_hw_init() with the irqs disabled
but a quick and dirty solution that has proven to work is
to reenable the irqs during the function rtl92ce_hw_init().
I think that it is safe doing so since the device interrupt will only be enabled after the init function succeed.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e8c5e56b307271c2dab6f8bfd1d8a3822ca2390 upstream.
rtl_ps_enable_nic() is called from loops that will loop until this function returns true or a
maximum number of retries is performed.
hw_init() returns non-zero on error. In that situation return false to
restore the original design intent to retry hw init when it fails.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6213e413a4e0c66548153516b074df14f9d08e0 upstream.
This patch fixes regression caused by commit a16dad77634 "MIPS: Fix
potencial corruption". That commit fixes one corruption scenario in
cost of adding another one, which actually start to cause crashes
on Yeeloong laptop when rtl8187 driver is used.
For correct DMA read operation on machines without DMA coherence, kernel
have to invalidate cache, such it will refill later with new data that
device wrote to memory, when that data is needed to process. We can only
invalidate full cache line. Hence when cache line includes both dma
buffer and some other data (written in cache, but not yet in main
memory), the other data can not hit memory due to invalidation. That
happen on rtl8187 where struct rtl8187_priv fields are located just
before and after small buffers that are passed to USB layer and DMA
is performed on them.
To fix the problem we align buffers and reserve space after them to make
them match cache line.
This patch does not resolve all possible MIPS problems entirely, for
that we have to assure that we always map cache aligned buffers for DMA,
what can be complex or even not possible. But patch fixes visible and
reproducible regression and seems other possible corruptions do not
happen in practice, since Yeeloong laptop works stable without rtl8187
driver.
Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=54391
Reported-by: Petr Pisar <petr.pisar@atlas.cz>
Bisected-by: Tom Li <biergaizi2009@gmail.com>
Reported-and-tested-by: Tom Li <biergaizi2009@gmail.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.next>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f66fab8e1cd6b3127ba4c5c0d11539fbe1de1e36 upstream.
According to BSpec the entire MI_DISPLAY_FLIP packet must be contained
in a single cacheline. Make sure that happens.
v2: Use intel_ring_begin_cacheline_safe()
v3: Use intel_ring_cacheline_align() (Chris)
Cc: Bjoern C <lkml@call-home.ch>
Cc: Alexandru DAMIAN <alexandru.damian@intel.com>
Cc: Enrico Tagliavini <enrico.tagliavini@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74053
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 753b1ad4a281b0663329409d410243e91825c323 upstream.
intel_ring_cachline_align() emits MI_NOOPs until the ring tail is
aligned to a cacheline boundary.
Cc: Bjoern C <lkml@call-home.ch>
Cc: Alexandru DAMIAN <alexandru.damian@intel.com>
Cc: Enrico Tagliavini <enrico.tagliavini@gmail.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7f1c1e65b68e1e1ab70898528d5977ed68a0a7d upstream.
Commit 0a0afd282f ("drm/nv50-/disp: move DP link training to core and
train from supervisor") added code that uses the wrong register for
computing the display bpp, used for bandwidth calculation. Adjust to use
the same register as used by exec_clkcmp and nv50_disp_intr_unk20_2_dp.
Reported-by: Torsten Wagner <torsten.wagner@gmail.com>
Reported-by: Michael Gulick <mgulick@mathworks.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67628
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95ca5b550ac255bf3cee108c123407785c47e3cc upstream.
commit 8613e7314ac254fdd67ed46192f021d76141e4c9
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon Oct 21 08:50:25 2013 +1000
drm/nouveau/fb: remove ram oclass argument from base fb constructor
Introduced a unfortunate regression by using nv10 ram oclass for nv1a
hardware, causing corruption and eventually system lockup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74866
Reported-by: John F. Godfrey <jfgodfrey@gmail.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d3428cd4b2ad51af86fdbdf8284ca38fa95e601 upstream.
Since commit 0fa9061ae8c ("drm/nouveau/mc: handle irq-related setup
ourselves"), drm_device->irq_enabled remained unset. This is needed in
order to properly wait for a vblank event in the generic drm code.
See https://bugs.freedesktop.org/show_bug.cgi?id=74195
Reported-by: Jan Janecek <janjanjanx@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f53492f86f9ca66bc762be98f0a9fce9bcb319a upstream.
The CP semaphore queue on CIK has a bug that triggers if uncompleted
waits use the same address while a signal is still pending. Work around
this by using different addresses for each sync.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb6ef42e516cb8948f15e4b70dc03af8020050a2 upstream.
We're using edac_mc_workq_setup() both on the init path, when
we load an edac driver and when we change the polling period
(edac_mc_reset_delay_period) through /sys/.../edac_mc_poll_msec.
On that second path we don't need to init the workqueue which has been
initialized already.
Thanks to Tejun for workqueue insights.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9da21b1509d8aa7ab4846722817d16c72d656c91 upstream.
Sanitize code even more to accept unsigned longs only and to not allow
polling intervals below 1 second as this is unnecessary and doesn't make
much sense anyway for polling errors.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc09149df6e20cfbb0bb86f10899607c321a31eb upstream.
This patch addresses a >= v3.11 free-after-use regression
in core_scsi3_emulate_pro_register() that was introduced
in the following commit:
commit bc118fe4c4a8cfa453491ba77c0a146a6d0e73e0
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:41:04 2013 -0700
target: Further refactoring of core_scsi3_emulate_pro_register()
To avoid the free-after-use, save an type value before hand, and
only call core_scsi3_put_pr_reg() with a valid *pr_reg.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79970db213344b4a4034645db5ebfc31571f3fa3 upstream.
Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 930ab3d403ae (i2c: mv64xxx: Add I2C Transaction Generator support)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 789b5e0315284463617e106baad360cb9e8db3ac upstream.
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Interestingly, the raid5 code can actually prevent double initialization and
hence can use the following simplified form of callback registration:
register_cpu_notifier(&foobar_cpu_notifier);
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
put_online_cpus();
A hotplug operation that occurs between registering the notifier and calling
get_online_cpus(), won't disrupt anything, because the code takes care to
perform the memory allocations only once.
So reorganize the code in raid5 this way to fix the deadlock with callback
registration.
Cc: linux-raid@vger.kernel.org
Fixes: 36d1c6476be51101778882897b315bd928c8c7b5
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[Srivatsa: Fixed the unregister_cpu_notifier() deadlock, added the
free_scratch_buffer() helper to condense code further and wrote the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1877db75589a895bbdc4c4c3f23558e57b521141 upstream.
commit 30bc9b53878a9921b02e3b5bc4283ac1c6de102a
md/raid1: fix bio handling problems in process_checks()
Move the bio_reset() to a point before where BIO_UPTODATE is checked,
so that check now always report that the bio is uptodate, even if it is not.
This causes process_check() to sometimes treat read-errors as
successful matches so the good data isn't written out.
This patch preserves the flag until it is needed.
Bug was introduced in 3.11, but backported to 3.10-stable (as it fixed
an even worse bug). So suitable for any -stable since 3.10.
Reported-and-tested-by: Michael Tokarev <mjt@tls.msk.ru>
Fixed: 30bc9b53878a9921b02e3b5bc4283ac1c6de102a
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f75e12c4457a9b3d042c0a0d748fa198dc2ffaf upstream.
Research has shown that commit a77fcf895046 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.
This patch add that sequence.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b1cc9b9622a022208ec95b1259b05bbdf712eb7 upstream.
iovcnt is declared as a signed integer in both the userspace API and
as a local variable in mic_virtio.c. The while() loop in mic_virtio.c
iterates until the local variable iovcnt reaches the value 0. If
userspace passes e.g. INT_MIN as iovcnt field, this loop then appears
to depend on an undefined behavior (signed underflow) to complete.
The fix is to use unsigned integers in both the userspace API and
the local variable.
This issue was reported @ https://lkml.org/lkml/2014/1/10/10
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7282059489868e0ed1b0d79765730c6b233a8399 upstream.
The ACPI specification (ACPI 5.0A, Section 6.3.7) says:
_STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which
no device driver should be loaded (for example, a bridge device.)
Children of this device may be present and valid. OSPM should
continue enumeration below a device whose _STA returns this bit
combination.
Evidently, some BIOSes follow that and return 0x0A from _STA, which
causes problems to happen when they trigger bus check or device check
notifications for those devices too. Namely, ACPIPHP thinks that they
are gone and may drop them, for example, if such a notification is
triggered during a resume from system suspend.
To fix that, modify ACPICA to regard devies as present and
functioning if _STA returns both the ACPI_STA_DEVICE_ENABLED
and ACPI_STA_DEVICE_FUNCTIONING bits set for them.
Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com>
[rjw: Subject and changelog, minor code modifications]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 140e3026a57ab7d830dab2f2c57796c222db0ea9 upstream.
Commit 9df89d85b407690afa46ddfbccc80bec6869971d "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.
Unfortunately, that's not the case. The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).
When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2
lspci for the affected host:
04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
Subsystem: 1043:1039
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at dd200000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <2us, L1 <32us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: xhci_hcd
Kernel modules: xhci_hcd
The commit was backported to stable kernels, and will need to be
reverted there as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Sergey Galanov <sergey.e.galanov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d4b81eda2211f32886e2978daf6f39885042fc4 upstream.
This reverts commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e. It's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. Commit 70cabb7d992f "xhci 1.0: Limit
arbitrarily-aligned scatter gather." should fix the issues seen with the
ax88179_178a driver on xHCI 1.0 hosts, without causing regressions.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cf00d91708221ff2d8a11143315f7ebab8d5da8 upstream.
This reverts commit d6c9ea9069af684358efedcaf2f2f687f51c58ee.
We are ripping out commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. This commit attempted to fix the
issues with that patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1386ff75797a187df324062fb4e929152392da88 upstream.
This reverts commit f2d9b991c549f159dc9ae81f77d8206c790cbfee.
We are ripping out commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. This commit attempted to fix the
issues with that patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 247bf557273dd775505fb9240d2d152f4f20d304 upstream.
xHCI 1.0 hosts have a set of requirements on how to align transfer
buffers on the endpoint rings called "TD fragment" rules. When the
ax88179_178a driver added support for scatter gather in 3.12, with
commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a:
enable tso if usb host supports sg dma", it broke the device under xHCI
1.0 hosts. Under certain network loads, the device would see an
unexpected short packet from the host, which would cause the device to
stop sending ethernet packets, even through USB packets would still be
sent.
Commit 35773dac5f86 "usb: xhci: Link TRB must not occur within a USB
payload burst" attempted to fix this. It was a quick hack to partially
implement the TD fragment rules. However, it caused regressions in the
usb-storage layer and userspace USB drivers using libusb. The patches
to attempt to fix this are too far reaching into the USB core, and we
really need to implement the TD fragment rules correctly in the xHCI
driver, instead of continuing to wallpaper over the issues.
Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0
hosts. Only the ax88179_178a driver checks the no_sg_constraint flag,
so don't set it for 1.0 hosts. This should not impact usb-storage or
usbfs behavior, since they pass down max packet sized aligned sg-list
entries (512 for USB 2.0 and 1024 for USB 3.0).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2240c365108adbc4100a55654a5707e8e877a401 upstream.
Add support for ANT USB-m Stick from Dynastream Innovations, by listing
USB pid
[34366.944805] usb 6-1: New USB device found, idVendor=0fcf, idProduct=1009
[34366.944817] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[34366.944824] usb 6-1: Product: ANT USB-m Stick
[34366.944831] usb 6-1: Manufacturer: Dynastream Innovations
Device reported (https://code.google.com/p/antpm/issues/detail?id=5) to
work through:
$ modprobe usbserial vendor=0x0fcf product=0x1009
Signed-off-by: Kristóf Ralovich <kristof.ralovich@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3635c7e2d59f7861afa6fa5e87e2a58860ff514d upstream.
Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 823d12c95c666fa7ab7dad208d735f6bc6afabdc upstream.
People sometimes create their own custom-configured kernels and forget
to enable CONFIG_SCSI_MULTI_LUN. This causes problems when they plug
in a USB storage device (such as a card reader) with more than one
LUN.
Fortunately, we can tell fairly easily when a storage device claims to
have more than one LUN. When that happens, this patch asks the SCSI
layer to probe all the LUNs automatically, regardless of the config
setting.
The patch also updates the Kconfig help text for usb-storage,
explaining that CONFIG_SCSI_MULTI_LUN may be necessary.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Thomas Raschbacher <lordvan@lordvan.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c143c82608bee2a36410caa56d82cd86bdc7fa upstream.
The Cypress ATACB unusual-devs entry for the Super Top SATA bridge
causes problems. Although it was originally reported only for
bcdDevice = 0x160, its range was much larger. This resulted in a bug
report for bcdDevice 0x220, so the range was capped at 0x219. Now
Milan reports errors with bcdDevice 0x150.
Therefore this patch restricts the range to just 0x160.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Milan Svoboda <milan.svoboda@centrum.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5637e5119c43452a00e27c274356b072263ecbb upstream.
This patch adds an unusual-devs entry for the BlackBerry 9000. This
fixes Bugzilla #22442.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Moritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Tested-by: Moritz Moeller-Herrmann <moritz-kernel@moeller-herrmann.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76f24e3f39a1a94bab0d54e98899d64abcd9f69c upstream.
Adding two more IDs to the ftdi_sio usb serial driver.
It now connects Tagsys RFID readers.
There might be more IDs out there for other Tagsys models.
Signed-off-by: Ulrich Hahn <uhahn@eanco.de>
Cc: Johan Hovold <johan@hovold.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
