commit 5026d7a9b2 upstream.
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3056e3aec8 upstream.
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbab0e4eec upstream.
read_swap_cache_async() can race against get_swap_page(), and stumble
across a SWAP_HAS_CACHE entry in the swap map whose page wasn't brought
into the swapcache yet.
This transient swap_map state is expected to be transitory, but the
actual placement of discard at scan_swap_map() inserts a wait for I/O
completion thus making the thread at read_swap_cache_async() to loop
around its -EEXIST case, while the other end at get_swap_page() is
scheduled away at scan_swap_map(). This can leave the system deadlocked
if the I/O completion happens to be waiting on the CPU waitqueue where
read_swap_cache_async() is busy looping and !CONFIG_PREEMPT.
This patch introduces a cond_resched() call to make the aforementioned
read_swap_cache_async() busy loop condition to bail out when necessary,
thus avoiding the subtle race window.
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3456fb3e4 upstream.
In
commit 53d3b4d777
Author: Egbert Eich <eich@suse.de>
Date: Tue Jun 4 17:13:21 2013 +0200
drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC
Egbert Eich fixed a long-standing bug where we simply used a
non-working i2c controller to read the EDID for SDVO-LVDS panels.
Unfortunately some machines seem to not be able to cope with the mode
provided in the EDID. Specifically they seem to not be able to cope
with a 4x pixel mutliplier instead of a 2x one, which seems to have
been worked around by slightly changing the panels native mode in the
VBT so that the dotclock is just barely above 50MHz.
Since it took forever to notice the breakage it's fairly safe to
assume that at least for SDVO-LVDS panels the VBT contains fairly sane
data. So just switch around the order and use VBT modes first.
v2: Also add EDID modes just in case, and spell Egbert correctly.
v3: Elaborate a bit more about what's going on on Chris' machine.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65524
Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60c28cf18f upstream.
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected. The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: Levi Pearson <levipearson@gmail.com>
Reported-by: Michael Scott <hashcode0f@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03f47e888d upstream.
If a new logical drive is added and the CCISS_REGNEWD ioctl is invoked
(as is normal with the Array Configuration Utility) the process will
hang as below. It attempts to acquire the same mutex twice, once in
do_ioctl() and once in cciss_unlocked_open(). The BKL was recursive,
the mutex isn't.
Linux version 3.10.0-rc2 (scameron@localhost.localdomain) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Fri May 24 14:32:12 CDT 2013
[...]
acu D 0000000000000001 0 3246 3191 0x00000080
Call Trace:
schedule+0x29/0x70
schedule_preempt_disabled+0xe/0x10
__mutex_lock_slowpath+0x17b/0x220
mutex_lock+0x2b/0x50
cciss_unlocked_open+0x2f/0x110 [cciss]
__blkdev_get+0xd3/0x470
blkdev_get+0x5c/0x1e0
register_disk+0x182/0x1a0
add_disk+0x17c/0x310
cciss_add_disk+0x13a/0x170 [cciss]
cciss_update_drive_info+0x39b/0x480 [cciss]
rebuild_lun_table+0x258/0x370 [cciss]
cciss_ioctl+0x34f/0x470 [cciss]
do_ioctl+0x49/0x70 [cciss]
__blkdev_driver_ioctl+0x28/0x30
blkdev_ioctl+0x200/0x7b0
block_ioctl+0x3c/0x40
do_vfs_ioctl+0x89/0x350
SyS_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
This mutex usage was added into the ioctl path when the big kernel lock
was removed. As it turns out, these paths are all thread safe anyway
(or can easily be made so) and we don't want ioctl() to be single
threaded in any case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 637241a900 upstream.
The dmesg_restrict sysctl currently covers the syslog method for access
dmesg, however /dev/kmsg isn't covered by the same protections. Most
people haven't noticed because util-linux dmesg(1) defaults to using the
syslog method for access in older versions. With util-linux dmesg(1)
defaults to reading directly from /dev/kmsg.
To fix /dev/kmsg, let's compare the existing interfaces and what they
allow:
- /proc/kmsg allows:
- open (SYSLOG_ACTION_OPEN) if CAP_SYSLOG since it uses a destructive
single-reader interface (SYSLOG_ACTION_READ).
- everything, after an open.
- syslog syscall allows:
- anything, if CAP_SYSLOG.
- SYSLOG_ACTION_READ_ALL and SYSLOG_ACTION_SIZE_BUFFER, if
dmesg_restrict==0.
- nothing else (EPERM).
The use-cases were:
- dmesg(1) needs to do non-destructive SYSLOG_ACTION_READ_ALLs.
- sysklog(1) needs to open /proc/kmsg, drop privs, and still issue the
destructive SYSLOG_ACTION_READs.
AIUI, dmesg(1) is moving to /dev/kmsg, and systemd-journald doesn't
clear the ring buffer.
Based on the comments in devkmsg_llseek, it sounds like actions besides
reading aren't going to be supported by /dev/kmsg (i.e.
SYSLOG_ACTION_CLEAR), so we have a strict subset of the non-destructive
syslog syscall actions.
To this end, move the check as Josh had done, but also rename the
constants to reflect their new uses (SYSLOG_FROM_CALL becomes
SYSLOG_FROM_READER, and SYSLOG_FROM_FILE becomes SYSLOG_FROM_PROC).
SYSLOG_FROM_READER allows non-destructive actions, and SYSLOG_FROM_PROC
allows destructive actions after a capabilities-constrained
SYSLOG_ACTION_OPEN check.
- /dev/kmsg allows:
- open if CAP_SYSLOG or dmesg_restrict==0
- reading/polling, after open
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=903192
[akpm@linux-foundation.org: use pr_warn_once()]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Tested-by: Josh Boyer <jwboyer@redhat.com>
Cc: Kay Sievers <kay@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf7df378aa upstream.
We recently noticed that reboot of a 1024 cpu machine takes approx 16
minutes of just stopping the cpus. The slowdown was tracked to commit
f96972f2dc ("kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()").
The current implementation does all the work of hot removing the cpus
before halting the system. We are switching to just migrating to the
boot cpu and then continuing with shutdown/reboot.
This also has the effect of not breaking x86's command line parameter
for specifying the reboot cpu. Note, this code was shamelessly copied
from arch/x86/kernel/reboot.c with bits removed pertaining to the
reboot_cpu command line parameter.
Signed-off-by: Robin Holt <holt@sgi.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16e53dbf10 upstream.
There are instances in the kernel where we would like to disable CPU
hotplug (from sysfs) during some important operation. Today the freezer
code depends on this and the code to do it was kinda tailor-made for
that.
Restructure the code and make it generic enough to be useful for other
usecases too.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5efac94999 upstream.
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9600593178 upstream.
This reverts commit 68d9e1fa24
This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 531671cb17 upstream.
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96570ffcca upstream.
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb3b3152b2 upstream.
There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22e7c385a8 upstream.
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Cedarview.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=889511
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=812113
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 820de86a90 upstream.
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Poulsbo.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=889511
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=812113
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24b8256a1f upstream.
When booted in legacy mode device_init_wakeup() gets called by
drivers/mfd/twl-core.c when the children are initialized. However, when
booted using device tree, the children are created with
of_platform_populate() instead add_children().
This means that the RTC driver will not have device_init_wakeup() set,
and we need to call it from the driver probe like RTC drivers typically
do.
Without this we cannot test PM wake-up events on omaps for cases where
there may not be any physical wake-up event.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7262cfca43 upstream.
Whether rbd_client_create() successfully creates a new client or
not, it takes responsibility for getting the ceph_opts structure
it's passed destroyed. If successful, the structure becomes
associated with the created client; if not, rbd_client_create()
will destroy it.
Previously, rbd_get_client() would call ceph_destroy_options()
if rbd_get_client() failed, and that meant it got called twice.
That led freeing various pointers more than once, which is never a
good idea.
This resolves:
http://tracker.ceph.com/issues/4559
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c420276a53 upstream.
In his review, Alex Elder mentioned that he hadn't checked that
num_fcntl_locks and num_flock_locks were properly decoded on the
server side, from a le32 over-the-wire type to a cpu type.
I checked, and AFAICS it is done; those interested can consult
Locker::_do_cap_update()
in src/mds/Locker.cc and src/include/encoding.h in the Ceph server
code (git://github.com/ceph/ceph).
I also checked the server side for flock_len decoding, and I believe
that also happens correctly, by virtue of having been declared
__le32 in struct ceph_mds_cap_reconnect, in src/include/ceph_fs.h.
Signed-off-by: Jim Schutt <jaschut@sandia.gov>
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14d2f38df6 upstream.
An osd client has a red-black tree describing its osds, and
occasionally we would get crashes due to one of these trees tree
becoming corrupt somehow.
The problem turned out to be that reset_changed_osds() was being
called without protection of the osd client request mutex. That
function would call __reset_osd() for any osd that had changed, and
__reset_osd() would call __remove_osd() for any osd with no
outstanding requests, and finally __remove_osd() would remove the
corresponding entry from the red-black tree. Thus, the tree was
getting modified without having any lock protection, and was
vulnerable to problems due to concurrent updates.
This appears to be the only osd tree updating path that has this
problem. It can be fairly easily fixed by moving the call up
a few lines, to just before the request mutex gets dropped
in kick_requests().
This resolves:
http://tracker.ceph.com/issues/5043
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9b7a7b2f upstream.
With the introduction of ACPI scan handlers, ACPI device objects
with an ACPI scan handler attached to them must not be bound to
by ACPI drivers any more. Unfortunately, however, the ACPI video
driver attempts to do just that if there is a _ROM ACPI control
method defined under a device object with an ACPI scan handler.
Prevent that from happening by making the video driver's "add"
routine check if the device object already has an ACPI scan handler
attached to it and return an error code in that case.
That is not sufficient, though, because acpi_bus_driver_init() would
then clear the device object's driver_data that may be set by its
scan handler, so for the fix to work acpi_bus_driver_init() has to be
modified to leave driver_data as is on errors.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091
Bisected-and-tested-by: Dmitry S. Demin <dmitryy.demin@gmail.com>
Reported-and-tested-by: Jason Cassell <bluesloth600@gmail.com>
Tracked-down-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0e29b683d upstream.
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f000cfdde5 upstream.
audit_log_start() does wait_for_auditd() in a loop until
audit_backlog_wait_time passes or audit_skb_queue has a room.
If signal_pending() is true this becomes a busy-wait loop, schedule() in
TASK_INTERRUPTIBLE won't block.
Thanks to Guy for fully investigating and explaining the problem.
(akpm: that'll cause the system to lock up on a non-preemptible
uniprocessor kernel)
(Guy: "Our customer was in fact running a uniprocessor machine, and they
reported a system hang.")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Guy Streeter <streeter@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 52f36be0f4 's390/pgtable: Fix check for pgste/storage key
handling', which was commit b56433cb78 upstream, added a use of
pgste to ptep_modify_prot_start(), but this variable does not exist.
In mainline, pgste was added by commit d3383632d4 's390/mm: add pte
invalidation notifier for kvm' and initialised to the return value of
pgste_get_lock(ptep). Initialise it similarly here.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d6bd9953f upstream.
Since commit 31ade30692, timekeeping_init()
checks for presence of persistent clock by attempting to read a non-zero
time value. This is an issue on platforms where persistent_clock (instead
is implemented as a free-running counter (instead of an RTC) starting
from zero on each boot and running during suspend. Examples are some ARM
platforms (e.g. PandaBoard).
An attempt to read such a clock during timekeeping_init() may return zero
value and falsely declare persistent clock as missing. Additionally, in
the above case suspend times may be accounted twice (once from
timekeeping_resume() and once from rtc_resume()), resulting in a gradual
drift of system time.
This patch does a run-time correction of the issue by doing the same check
during timekeeping_suspend().
A better long-term solution would have to return error when trying to read
non-existing clock and zero when trying to read an uninitialized clock, but
that would require changing all persistent_clock implementations.
This patch addresses the immediate breakage, for now.
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
[jstultz: Tweaked commit message and subject]
Signed-off-by: John Stultz <john.stultz@linaro.org>
[zoran.markovic@linaro.org: reworked patch to fit 3.9-stable.]
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 466318a87f upstream.
The xen_play_dead is an undead function. When the vCPU is told to
offline it ends up calling xen_play_dead wherin it calls the
VCPUOP_down hypercall which offlines the vCPU. However, when the
vCPU is onlined back, it resumes execution right after
VCPUOP_down hypercall.
That was OK (albeit the API for play_dead assumes that the CPU
stays dead and never returns) but with commit 4b0c0f294
(tick: Cleanup NOHZ per cpu data on cpu down) that is no longer safe
as said commit resets the ts->inidle which at the start of the
cpu_idle loop was set.
The net effect is that we get this warn:
Broke affinity for irq 16
installing Xen timer for CPU 1
cpu 1 spinlock event irq 48
------------[ cut here ]------------
WARNING: at /home/konrad/linux-linus/kernel/time/tick-sched.c:935 tick_nohz_idle_exit+0x195/0x1b0()
Modules linked in: dm_multipath dm_mod xen_evtchn iscsi_boot_sysfs
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.10.0-rc3upstream-00068-gdcdbe33 #1
Hardware name: BIOSTAR Group N61PB-M2S/N61PB-M2S, BIOS 6.00 PG 09/03/2009
ffffffff8193b448 ffff880039da5e60 ffffffff816707c8 ffff880039da5ea0
ffffffff8108ce8b ffff880039da4010 ffff88003fa8e500 ffff880039da4010
0000000000000001 ffff880039da4000 ffff880039da4010 ffff880039da5eb0
Call Trace:
[<ffffffff816707c8>] dump_stack+0x19/0x1b
[<ffffffff8108ce8b>] warn_slowpath_common+0x6b/0xa0
[<ffffffff8108ced5>] warn_slowpath_null+0x15/0x20
[<ffffffff810e4745>] tick_nohz_idle_exit+0x195/0x1b0
[<ffffffff810da755>] cpu_startup_entry+0x205/0x250
[<ffffffff81661070>] cpu_bringup_and_idle+0x13/0x15
---[ end trace 915c8c486004dda1 ]---
b/c ts_inidle is set to zero. Thomas suggested that we just add a workaround
to call tick_nohz_idle_enter before returning from xen_play_dead() - and
that is what this patch does and fixes the issue.
We also add the stable part b/c git commit 4b0c0f294 is on the stable
tree.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
commit 34376a50fb upstream.
The stop machine logic can lock up if all but one of the migration
threads make it through the disable-irq step and the one remaining
thread gets stuck in __do_softirq. The reason __do_softirq can hang is
that it has a bail-out based on jiffies timeout, but in the lockup case,
jiffies itself is not incremented.
To work around this, re-add the max_restart counter in __do_irq and stop
processing irqs after 10 restarts.
Thanks to Tejun Heo and Rusty Russell and others for helping me track
this down.
This was introduced in 3.9 by commit c10d73671a ("softirq: reduce
latencies").
It may be worth looking into ath9k to see if it has issues with its irq
handler at a later date.
The hang stack traces look something like this:
------------[ cut here ]------------
WARNING: at kernel/watchdog.c:245 watchdog_overflow_callback+0x9c/0xa7()
Watchdog detected hard LOCKUP on cpu 2
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
Pid: 23, comm: migration/2 Tainted: G C 3.9.4+ #11
Call Trace:
<NMI> warn_slowpath_common+0x85/0x9f
warn_slowpath_fmt+0x46/0x48
watchdog_overflow_callback+0x9c/0xa7
__perf_event_overflow+0x137/0x1cb
perf_event_overflow+0x14/0x16
intel_pmu_handle_irq+0x2dc/0x359
perf_event_nmi_handler+0x19/0x1b
nmi_handle+0x7f/0xc2
do_nmi+0xbc/0x304
end_repeat_nmi+0x1e/0x2e
<<EOE>>
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
---[ end trace 4947dfa9b0a4cec3 ]---
BUG: soft lockup - CPU#1 stuck for 22s! [migration/1:17]
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
irq event stamp: 835637905
hardirqs last enabled at (835637904): __do_softirq+0x9f/0x257
hardirqs last disabled at (835637905): apic_timer_interrupt+0x6d/0x80
softirqs last enabled at (5654720): __do_softirq+0x1ff/0x257
softirqs last disabled at (5654725): irq_exit+0x5f/0xbb
CPU 1
Pid: 17, comm: migration/1 Tainted: G WC 3.9.4+ #11 To be filled by O.E.M. To be filled by O.E.M./To be filled by O.E.M.
RIP: tasklet_hi_action+0xf0/0xf0
Process migration/1
Call Trace:
<IRQ>
__do_softirq+0x117/0x257
irq_exit+0x5f/0xbb
smp_apic_timer_interrupt+0x8a/0x98
apic_timer_interrupt+0x72/0x80
<EOI>
printk+0x4d/0x4f
stop_machine_cpu_stop+0x22c/0x274
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Pekka Riikonen <priikone@iki.fi>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16634adce upstream.
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 263e1f9f ("USB:
io_ti: query hardware-buffer status in chars_in_buffer") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a37025b5c7 upstream.
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 6f602912 ("usb:
serial: ftdi_sio: Add missing chars_in_buffer function") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Reported-by: Stas Sergeev <stsp@list.ru>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4133648bb upstream.
Use usb-serial port rather than tty as argument to get_modem_status.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcf0105039 upstream.
Add generic wait_until_sent implementation which polls for empty
hardware buffers using the new port-operation tx_empty.
The generic implementation will be used for all sub-drivers that
implement tx_empty but does not define wait_until_sent.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0693196fe7 upstream.
Add wait_until_sent operation which can be used to wait for hardware
buffers to drain.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3de42b684 upstream.
Currently the driver's assumed behavior for a modeset with an attached
FB is that the corresponding connector will be switched to DPMS ON mode
if it happened to be in DPMS OFF (or another power save mode). This
wasn't enforced though if only the FB changed, everything else (format,
connector etc.) remaining the same. In this case we only set the new FB
base and left the connector in the old power save mode.
Fix this by forcing a full modeset whenever there is an attached FB and
any affected connector is in a power save mode.
V_2: Run the test for encoders in power save mode outside the the
test for fb change: user space may have just disabled the encoders
but left everything else in place. Make sure the connector list is
not empty before running this test.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Egbert Eich <eich@suse.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61642
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59834
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59339
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64178
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65559
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Apply Jani's s/connector_off/is_crtc_connector_off bikeshed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0e419637 upstream.
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d82fb31abc upstream.
On pseries machines the detection for max_bus_speed should be done
through an OpenFirmware property. This patch adds a function to perform
this detection and a hook to perform dynamic adding of the function only
for pseries. This is done by overwriting the weak
pcibios_root_bridge_prepare function which is called by
pci_create_root_bus().
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1dd153121 upstream.
Recent commit e61133dda4 added support
for a new firmware feature to force an adapter to use 32 bit MSIs.
However, this firmware is not available for all systems. The hack below
allows devices needing 32 bit MSIs to work on these systems as well.
It is careful to only enable this on Gen2 slots, which should limit
this to configurations where this hack is needed and tested to work.
[Small change to factor out the hack into a separate function -- BenH]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e61133dda4 upstream.
The following patch implements a new PAPR change which allows
the OS to force the use of 32 bit MSIs, regardless of what
the PCI capabilities indicate. This is required for some
devices that advertise support for 64 bit MSIs but don't
actually support them.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2e1d84523 upstream.
Add a PCI quirk for VGA devices on Power to set the default VGA device.
Ensures a default VGA is always set if a graphics adapter is present,
even if firmware did not initialize it. If more than one graphics
adapter is present, ensure the one initialized by firmware is set
as the default VGA device. This ensures that X autoconfiguration
will work.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88e7b167a0 upstream.
Set dev->dev.type in alloc_pci_dev so that archs that have their own
versions of pci_setup_device get this set properly in order to ensure
things like the boot_vga sysfs parameter get created as expected.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbbd379aa4 upstream.
By having a higher max resolution we can now set up a virtual
framebuffer that spans several monitors. 4096 should be ok since we're
gen 3 or higher and should be enough for most dual head setups.
Bugzilla:
https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-modesetting/+bug/1169147
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bf8fae33d upstream.
we never allocate a TRB pool for physical endpoints
0 and 1 so trying to free it (a invalid TRB pool pointer)
will lead us in a warning while removing dwc3.ko module.
In order to fix the situation, all we have to do is skip
dwc3_free_trb_pool() for physical endpoints 0 and 1 just
as we while deleting endpoints from the endpoints list.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea7f665612 upstream.
Commit 9f29ab11dd ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600. Tony says:
"It panics with the message:
Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel
[...] my problem comes from arch/ia64/hp/common/sba_iommu.c
where the code in sba_init() says:
acpi_bus_register_driver(&acpi_sba_ioc_driver);
if (!ioc_list) {
but because of this change we never managed to call ioc_init()
so ioc_list doesn't get set up, and we die."
Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7abb690a0e upstream.
Chris Wilson noticed that since
commit 1f83fee08d [v3.9]
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Nov 15 17:17:22 2012 +0100
drm/i915: clear up wedged transitions
X can again get -EIO when it does not expect it. And even worse score
a SIGBUS when accessing gtt mmaps. The established ABI is that we
_only_ return an -EIO from execbuf - all other ioctls should just
work. And since the reset code moves all bos out of gpu domains and
clears out all the last_seqno/ring tracking there really shouldn't be
any reason for non-execbuf code to ever touch the hw and see an -EIO.
After some extensive discussions we've noticed that these spurios -EIO
are caused by i915_gem_wait_for_error:
http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg20540.html
That is easy to fix by returning 0 instead of -EIO, since grabbing the
dev->struct_mutex does not yet mean that we actually want to touch the
hw. And so there is no reason at all to fail with -EIO.
But that's not the entire since, since often (at least it's easily
googleable) dmesg indicates that the reset fails and we declare the
gpu wedged. Then, quite a bit later X wakes up with the "Timed out
waiting for the gpu reset to complete" DRM_ERROR message in
wait_for_errror and brings down the desktop with an -EIO/SIGBUS.
So clearly we're missing a wakeup somewhere, since the gpu reset just
doesn't take 10 seconds to complete. And indeed we're do handle the
terminally wedged state wrong.
Fix this all up.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45a211d751 upstream.
Last year, a patch was made for the "HP t5740e Thin Client" (see
http://lists.freedesktop.org/archives/dri-devel/2012-May/023245.html).
This device reports an lvds panel, but does not really have one.
The predecessor of this device is the "hp t5740", which also does not have
an lvds panel. This patch will add the same quirk for this device.
Signed-off-by: Ben Mesman <ben@bnc.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
