commit 469d7d22ce upstream.
The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.
Fixes: 36874c7e21 ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)
Signed-off-by: Frodo Lai <frodo_lai@bcmcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dbb4c6167 upstream.
41f8bba7f5 ("of/pci: Add pci_register_io_range() and
pci_pio_to_address()") added support for systems with several I/O ranges
described by OF bindings. It modified pci_address_to_pio() look up the
io_range for a given CPU physical address, but the conversion was wrong.
Fix the conversion of address to I/O port.
[bhelgaas: changelog]
Fixes: 41f8bba7f5 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()")
Signed-off-by: Zhichang Yuan <yuanzhichang@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5dd4b4b05 upstream.
The commit referenced below deferred waiting for command completion until
the start of the next command, allowing hardware to do the latching
asynchronously. Unfortunately, being ready to accept a new command is the
only indication we have that the previous command is completed. In cases
where we need that state change to be enabled, we must still wait for
completion. For instance, pciehp_reset_slot() attempts to disable anything
that might generate a surprise hotplug on slots that support presence
detection. If we don't wait for those settings to latch before the
secondary bus reset, we negate any value in attempting to prevent the
spurious hotplug.
Create a base function with optional wait and helper functions so that
pcie_write_cmd() turns back into the "safe" interface which waits before
and after issuing a command and add pcie_write_cmd_nowait(), which
eliminates the trailing wait for asynchronous completion. The following
functions are returned to their previous behavior:
pciehp_power_on_slot
pciehp_power_off_slot
pcie_disable_notification
pciehp_reset_slot
The rationale is that pciehp_power_on_slot() enables the link and therefore
relies on completion of power-on. pciehp_power_off_slot() and
pcie_disable_notification() need a wait because data structures may be
freed after these calls and continued signaling from the device would be
unexpected. And, of course, pciehp_reset_slot() needs to wait for the
scenario outlined above.
Fixes: 3461a06866 ("PCI: pciehp: Wait for hotplug command completion lazily")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a9ad0b4fd upstream.
David Ahern reported that d63e2e1f3d ("sparc/PCI: Clip bridge windows
to fit in upstream windows") fails to boot on sparc/T5-8:
pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000)
The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA
addresses, i.e., bus addresses returned via the DMA API (dma_map_single(),
etc.), while the PCI core assumed dma_addr_t could hold *any* bus address,
including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so
dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so
they don't fit in a dma_addr_t. d63e2e1f3d added new checking that
tripped over this mismatch.
Add pci_bus_addr_t, which is wide enough to hold any PCI bus address,
including both raw BAR values and DMA addresses. This will be 64 bits
on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then
dma_addr_t only needs to be wide enough to hold addresses from the DMA API.
[bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at
least as wide as dma_addr_t, documentation]
Fixes: d63e2e1f3d ("sparc/PCI: Clip bridge windows to fit in upstream windows")
Fixes: 23b13bc76f ("PCI: Fail safely if we can't handle BARs larger than 4GB")
Link: http://lkml.kernel.org/r/CAE9FiQU1gJY1LYrxs+ma5LCTEEe4xmtjRG0aXJ9K_Tsu+m9Wuw@mail.gmail.com
Link: http://lkml.kernel.org/r/1427857069-6789-1-git-send-email-yinghai@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96231
Reported-by: David Ahern <david.ahern@oracle.com>
Tested-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0824965140 upstream.
Refine the mechanism introduced by commit f244d8b623 ("ACPIPHP / radeon /
nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the
ignore_hotplug setting of the device to its parent bridge in case hotplug
notifications related to the graphics adapter switching are given for the
bridge rather than for the device itself (they need to be ignored in both
cases).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891
Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927
Fixes: b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Reported-and-tested-by: tiagdtd-lava <tiagdtd-lava@yahoo.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5babdf928 upstream.
Since commit bd31b85960 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock
that needs usage of the corresponding raw functions.
This fixes:
drivers/mtd/maps/dc21285.c: In function 'nw_en_write':
drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
spin_lock_irqsave(&nw_gpio_lock, flags);
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline raw_spinlock_t *spinlock_check(spinlock_t *lock)
^
drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
spin_unlock_irqrestore(&nw_gpio_lock, flags);
^
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)
Fixes: bd31b85960 ("locking, ARM: Annotate low level hw locks as raw")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 073db4a51e upstream.
On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to
mtd->usecount were done without taking mtd_table_mutex.
kernel: Call Trace:
kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50
kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8
kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200
kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30
kernel: [<ffffffff8022006c>] __fput+0xac/0x250
kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120
kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18
kernel:
kernel:
Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003
00000000 0040f809 00000000
kernel: ---[ end trace 080fbb4579b47a73 ]---
Fixed by taking the mutex in blktrans_open and blktrans_release.
Note that this locking is already suggested in
include/linux/mtd/blktrans.h:
struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};
But we weren't following it.
Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.
Reported-by: Zhang Xingcai <zhangxingcai@huawei.com>
Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 084609bf72 upstream.
Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of
hibernation callbacks means those pm functions will not be
called upon hibernation - that leads to system crash on ARM during
freezing if gpio-led is used in combination with CPU led trigger.
It may happen after freeze_noirq stage (GPIO is suspended)
and before syscore_suspend stage (CPU led trigger is suspended)
- usually when disable_nonboot_cpus() is called.
Log:
PM: noirq freeze of devices complete after 1.425 msecs
Disabling non-boot CPUs ...
^ system may crash or stuck here with message (TI AM572x)
WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access
CPU1: shutdown
^ or here
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation callbacks and move
led_suspend/led_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Fixes: 73e1ab41a8 (leds: Convert led class driver from legacy pm ops to dev_pm_ops)
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fa3b4c4a7 upstream.
The LCDIF engines embedded in i.MX6sl and i.MX6sx SoCs need the axi clock
as the engine's system clock. The clock should be enabled when accessing
LCDIF registers, otherwise the kernel would hang up. We should also keep
the clock enabled when the engine is being active to scan out frames from
memory. This patch makes sure the axi clock is enabled when accessing
registers so that the kernel hang up issue can be fixed.
Reported-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63781394c5 upstream.
request_any_context_irq() returns a negative value on failure.
It returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED on success.
So fix testing return value of request_any_context_irq().
Also fixup the return value of devm_request_any_context_irq() to make it
consistent with request_any_context_irq().
Fixes: 0668d30651 ("genirq: Add devm_request_any_context_irq()")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Link: http://lkml.kernel.org/r/1431334978.17783.4.camel@ingics.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a44074f14b upstream.
Although it is possible to let SRP I/O continue if a reconnect
results in a reduction of the number of channels, the current
code does not handle this scenario correctly. Instead of making
the reconnect code more complex, consider this as a reconnection
failure.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c014c8cd31 upstream.
Reception of a DREQ message only causes the state of a single
channel to change. Hence move the 'connected' member variable
from the target to the channel data structure. This patch
avoids that following false positive warning can be reported
by srp_destroy_qp():
WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:617 srp_destroy_qp+0xa6/0x120 [ib_srp]()
Call Trace:
[<ffffffff8106e10f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8106e16a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0440226>] srp_destroy_qp+0xa6/0x120 [ib_srp]
[<ffffffffa0440322>] srp_free_ch_ib+0x82/0x1e0 [ib_srp]
[<ffffffffa044408b>] srp_create_target+0x7ab/0x998 [ib_srp]
[<ffffffff81346f60>] dev_attr_store+0x20/0x30
[<ffffffff811dd90f>] sysfs_write_file+0xef/0x170
[<ffffffff8116d248>] vfs_write+0xc8/0x190
[<ffffffff8116d411>] sys_write+0x51/0x90
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8de9fe3a1d upstream.
Avoid that receiving a DREQ while RDMA channels are being
established causes target->qp_in_error to be reset.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb49c8bbaa upstream.
Fix a scsi_get_host() / scsi_host_put() imbalance in the error
path of srp_create_target(). See also patch "IB/srp: Avoid that
I/O hangs due to a cable pull during LUN scanning" (commit ID
34aa654ecb).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 535fb90622 upstream.
Avoid that srp_terminate_io() can get invoked while srp_queuecommand()
is in progress. This patch avoids that an I/O timeout can trigger the
following kernel warning:
WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:1447 srp_terminate_io+0xef/0x100 [ib_srp]()
Call Trace:
[<ffffffff814c65a2>] dump_stack+0x4e/0x68
[<ffffffff81051f71>] warn_slowpath_common+0x81/0xa0
[<ffffffff8105204a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa075f51f>] srp_terminate_io+0xef/0x100 [ib_srp]
[<ffffffffa07495da>] __rport_fail_io_fast+0xba/0xc0 [scsi_transport_srp]
[<ffffffffa0749a90>] rport_fast_io_fail_timedout+0xe0/0xf0 [scsi_transport_srp]
[<ffffffff8106e09b>] process_one_work+0x1db/0x780
[<ffffffff8106e75b>] worker_thread+0x11b/0x450
[<ffffffff81073c64>] kthread+0xe4/0x100
[<ffffffff814cf26c>] ret_from_fork+0x7c/0xb0
See also patch "scsi_transport_srp: Add transport layer error
handling" (commit ID 29c1732480).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: James Bottomley <JBottomley@Odin.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be34c62ddf upstream.
Introduce the helper function srp_wait_for_queuecommand().
Move the definition of scsi_request_fn_active(). Add a comment
above srp_wait_for_queuecommand() that support for scsi-mq needs
to be added.
This patch does not change any functionality. A second call to
srp_wait_for_queuecommand() will be introduced in the next patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: James Bottomley <JBottomley@Odin.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea6055c46e upstream.
Since commit 39a6ac11df ("spi/pl022: Devicetree support w/o platform data")
the 'num-cs' parameter cannot be passed through platform data when probing
with devicetree. Instead, it's a required devicetree property.
Fix the binding documentation so the property is properly specified.
Fixes: 39a6ac11df ("spi/pl022: Devicetree support w/o platform data")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce2f6ea1cb upstream.
The commit df59fa7f4b "spi: orion: support armada extended baud
rates" was too optimistic for the maximum baud rate that the Armada
SoCs can support. According to the hardware datasheet the maximum
frequency supported by the Armada 370 SoC is tclk/4. But for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
Currently the armada-370-spi compatible is only used by the Armada 370
and the Armada XP device tree. On Armada 370, tclk cannot be higher
than 200MHz. In order to be able to handle both SoCs, we can take the
minimum of 50MHz and tclk/4.
A proper solution is adding a compatible string for each SoC, but it
can't be done as a fix for compatibility reason (we can't modify
device tree that have been already released) and it will be part of a
separate patch.
Fixes: df59fa7f4b (spi: orion: support armada extended baud rates)
Reported-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e76ef88f6 upstream.
Fix a race (with some kernel configurations) where a queued
master->pump_messages runs and frees dummy_tx/rx before
spi_unmap_msg is running (or is finished).
This results in the following messages:
BUG: Bad page state in process
page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x200(arch_1)
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
...
Reported-by: Noralf Trønnes <noralf@tronnes.org>
Suggested-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a1bd63cda upstream.
The list of loaded modules is walked through in
module_kallsyms_on_each_symbol (called by kallsyms_on_each_symbol). The
module_mutex lock should be acquired to prevent potential corruptions
in the list.
This was uncovered with new lockdep asserts in module code introduced by
the commit 0be964be0d ("module: Sanitize RCU usage and locking") in
recent next- trees.
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7068e3932 upstream.
The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c53403a37c upstream.
The code should handle more than 32 bits here because "id"
can be a value up to MAX77686_REGULATORS (currently 34).
Convert the gpio_enabled type to DECLARE_BITMAP and use
test_bit/set_bit.
Fixes: 3307e9025d ("regulator: max77686: Add GPIO control")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 921cc29473 upstream.
The way the mask is generated in regmap_field_init() is wrong.
Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift
overflow while calculating the mask field.
On some 32 bits architectures, such as x86, the generated mask is 0,
instead of the expected 0xffffffff.
This patch uses GENMASK() to fix the problem, as this macro is already safe
regarding shift overflow.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15b8d2c41f upstream.
In big endian mode regmap_bulk_read gives incorrect data
for byte reads.
This is because memcpy of a single byte from an address
after full word read gives different results when
endianness differs. ie. we get little-end in LE and big-end in BE.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f1b6b7d9a upstream.
When receiving a new iser connect request we serialize
the pending requests by adding the newly created iser connection
to the np accept list and let the login thread process the connect
request one by one (np_accept_wait).
In case we received a disconnect request before the iser_conn
has begun processing (still linked in np_accept_list) we should
detach it from the list and clean it up and not have the login
thread process a stale connection. We do it only when the connection
state is not already terminating (initiator driven disconnect) as
this might lead us to access np_accept_mutex after the np was released
in live shutdown scenarios.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0867a57c4f upstream.
Since commit 077fcf116c ("mm/thp: allocate transparent hugepages on
local node"), we handle THP allocations on page fault in a special way -
for non-interleave memory policies, the allocation is only attempted on
the node local to the current CPU, if the policy's nodemask allows the
node.
This is motivated by the assumption that THP benefits cannot offset the
cost of remote accesses, so it's better to fallback to base pages on the
local node (which might still be available, while huge pages are not due
to fragmentation) than to allocate huge pages on a remote node.
The nodemask check prevents us from violating e.g. MPOL_BIND policies
where the local node is not among the allowed nodes. However, the
current implementation can still give surprising results for the
MPOL_PREFERRED policy when the preferred node is different than the
current CPU's local node.
In such case we should honor the preferred node and not use the local
node, which is what this patch does. If hugepage allocation on the
preferred node fails, we fall back to base pages and don't try other
nodes, with the same motivation as is done for the local node hugepage
allocations. The patch also moves the MPOL_INTERLEAVE check around to
simplify the hugepage specific test.
The difference can be demonstrated using in-tree transhuge-stress test
on the following 2-node machine where half memory on one node was
occupied to show the difference.
> numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 24 25 26 27 28 29 30 31 32 33 34 35
node 0 size: 7878 MB
node 0 free: 3623 MB
node 1 cpus: 12 13 14 15 16 17 18 19 20 21 22 23 36 37 38 39 40 41 42 43 44 45 46 47
node 1 size: 8045 MB
node 1 free: 7818 MB
node distances:
node 0 1
0: 10 21
1: 21 10
Before the patch:
> numactl -p0 -C0 ./transhuge-stress
transhuge-stress: 2.197 s/loop, 0.276 ms/page, 7249.168 MiB/s 7962 succeed, 0 failed, 1786 different pages
> numactl -p0 -C12 ./transhuge-stress
transhuge-stress: 2.962 s/loop, 0.372 ms/page, 5376.172 MiB/s 7962 succeed, 0 failed, 3873 different pages
Number of successful THP allocations corresponds to free memory on node 0 in
the first case and node 1 in the second case, i.e. -p parameter is ignored and
cpu binding "wins".
After the patch:
> numactl -p0 -C0 ./transhuge-stress
transhuge-stress: 2.183 s/loop, 0.274 ms/page, 7295.516 MiB/s 7962 succeed, 0 failed, 1760 different pages
> numactl -p0 -C12 ./transhuge-stress
transhuge-stress: 2.878 s/loop, 0.361 ms/page, 5533.638 MiB/s 7962 succeed, 0 failed, 1750 different pages
> numactl -p1 -C0 ./transhuge-stress
transhuge-stress: 4.628 s/loop, 0.581 ms/page, 3440.893 MiB/s 7962 succeed, 0 failed, 3918 different pages
The -p parameter is respected regardless of cpu binding.
> numactl -C0 ./transhuge-stress
transhuge-stress: 2.202 s/loop, 0.277 ms/page, 7230.003 MiB/s 7962 succeed, 0 failed, 1750 different pages
> numactl -C12 ./transhuge-stress
transhuge-stress: 3.020 s/loop, 0.379 ms/page, 5273.324 MiB/s 7962 succeed, 0 failed, 3916 different pages
Without -p parameter, hugepage restriction to CPU-local node works as before.
Fixes: 077fcf116c ("mm/thp: allocate transparent hugepages on local node")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a8c35fadf upstream.
Beginning at commit d52d3997f8 ("ipv6: Create percpu rt6_info"), the
following INFO splat is logged:
===============================
[ INFO: suspicious RCU usage. ]
4.1.0-rc7-next-20150612 #1 Not tainted
-------------------------------
kernel/sched/core.c:7318 Illegal context switch in RCU-bh read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
3 locks held by systemd/1:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff815f0c8f>] rtnetlink_rcv+0x1f/0x40
#1: (rcu_read_lock_bh){......}, at: [<ffffffff816a34e2>] ipv6_add_addr+0x62/0x540
#2: (addrconf_hash_lock){+...+.}, at: [<ffffffff816a3604>] ipv6_add_addr+0x184/0x540
stack backtrace:
CPU: 0 PID: 1 Comm: systemd Not tainted 4.1.0-rc7-next-20150612 #1
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20 04/17/2014
Call Trace:
dump_stack+0x4c/0x6e
lockdep_rcu_suspicious+0xe7/0x120
___might_sleep+0x1d5/0x1f0
__might_sleep+0x4d/0x90
kmem_cache_alloc+0x47/0x250
create_object+0x39/0x2e0
kmemleak_alloc_percpu+0x61/0xe0
pcpu_alloc+0x370/0x630
Additional backtrace lines are truncated. In addition, the above splat
is followed by several "BUG: sleeping function called from invalid
context at mm/slub.c:1268" outputs. As suggested by Martin KaFai Lau,
these are the clue to the fix. Routine kmemleak_alloc_percpu() always
uses GFP_KERNEL for its allocations, whereas it should follow the gfp
from its callers.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5f3b1a51a upstream.
The kmemleak scanning thread can run for minutes. Callbacks like
kmemleak_free() are allowed during this time, the race being taken care
of by the object->lock spinlock. Such lock also prevents a memory block
from being freed or unmapped while it is being scanned by blocking the
kmemleak_free() -> ... -> __delete_object() function until the lock is
released in scan_object().
When a kmemleak error occurs (e.g. it fails to allocate its metadata),
kmemleak_enabled is set and __delete_object() is no longer called on
freed objects. If kmemleak_scan is running at the same time,
kmemleak_free() no longer waits for the object scanning to complete,
allowing the corresponding memory block to be freed or unmapped (in the
case of vfree()). This leads to kmemleak_scan potentially triggering a
page fault.
This patch separates the kmemleak_free() enabling/disabling from the
overall kmemleak_enabled nob so that we can defer the disabling of the
object freeing tracking until the scanning thread completed. The
kmemleak_free_part() is deliberately ignored by this patch since this is
only called during boot before the scanning thread started.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Vignesh Radhakrishnan <vigneshr@codeaurora.org>
Tested-by: Vignesh Radhakrishnan <vigneshr@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f1a6ae87c upstream.
When building the kernel with a bare-metal (ELF) toolchain, the -shared
option may not be passed down to collect2, resulting in silent corruption
of the vDSO image (in particular, the DYNAMIC section is omitted).
The effect of this corruption is that the dynamic linker fails to find
the vDSO symbols and libc is instead used for the syscalls that we
intended to optimise (e.g. gettimeofday). Functionally, there is no
issue as the sigreturn trampoline is still intact and located by the
kernel.
This patch fixes the problem by explicitly passing -shared to the linker
when building the vDSO.
Reported-by: Szabolcs Nagy <Szabolcs.Nagy@arm.com>
Reported-by: James Greenlaigh <james.greenhalgh@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9bcc91993 upstream.
The memmap freeing code in free_unused_memmap() computes the end of
each memblock by adding the memblock size onto the base. However,
if SPARSEMEM is enabled then the value (start) used for the base
may already have been rounded downwards to work out which memmap
entries to free after the previous memblock.
This may cause memmap entries that are in use to get freed.
In general, you're not likely to hit this problem unless there
are at least 2 memblocks and one of them is not aligned to a
sparsemem section boundary. Note that carve-outs can increase
the number of memblocks by splitting the regions listed in the
device tree.
This problem doesn't occur with SPARSEMEM_VMEMMAP, because the
vmemmap code deals with freeing the unused regions of the memmap
instead of requiring the arch code to do it.
This patch gets the memblock base out of the memblock directly when
computing the block end address to ensure the correct value is used.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46b0567c85 upstream.
Commit 6c81fe7925 ("arm64: enable context tracking") did not
update el0_sp_pc to use ct_user_exit, but this appears to have been
unintentional. In commit 6ab6463aeb ("arm64: adjust el0_sync so
that a function can be called") we made x0 available, and in the return
to userspace we call ct_user_enter in the kernel_exit macro.
Due to this, we currently don't correctly inform RCU of the user->kernel
transition, and may erroneously account for time spent in the kernel as
if we were in an extended quiescent state when CONFIG_CONTEXT_TRACKING
is enabled.
As we do record the kernel->user transition, a userspace application
making accesses from an unaligned stack pointer can demonstrate the
imbalance, provoking the following warning:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 3660 at kernel/context_tracking.c:75 context_tracking_enter+0xd8/0xe4()
Modules linked in:
CPU: 2 PID: 3660 Comm: a.out Not tainted 4.1.0-rc7+ #8
Hardware name: ARM Juno development board (r0) (DT)
Call trace:
[<ffffffc000089914>] dump_backtrace+0x0/0x124
[<ffffffc000089a48>] show_stack+0x10/0x1c
[<ffffffc0005b3cbc>] dump_stack+0x84/0xc8
[<ffffffc0000b3214>] warn_slowpath_common+0x98/0xd0
[<ffffffc0000b330c>] warn_slowpath_null+0x14/0x20
[<ffffffc00013ada4>] context_tracking_enter+0xd4/0xe4
[<ffffffc0005b534c>] preempt_schedule_irq+0xd4/0x114
[<ffffffc00008561c>] el1_preempt+0x4/0x28
[<ffffffc0001b8040>] exit_files+0x38/0x4c
[<ffffffc0000b5b94>] do_exit+0x430/0x978
[<ffffffc0000b614c>] do_group_exit+0x40/0xd4
[<ffffffc0000c0208>] get_signal+0x23c/0x4f4
[<ffffffc0000890b4>] do_signal+0x1ac/0x518
[<ffffffc000089650>] do_notify_resume+0x5c/0x68
---[ end trace 963c192600337066 ]---
This patch adds the missing ct_user_exit to the el0_sp_pc entry path,
correcting the context tracking for this case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Fixes: 6c81fe7925 ("arm64: enable context tracking")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 565630d503 upstream.
After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe292283c2 upstream.
HW has to be in known state before the initialisation
sequence is started. The polling step for settling aliveness
was set to 200ms while in practise this can be done in up to 30msecs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Barak Yoresh <barak.yoresh@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dc196eae1 upstream.
Fix the hbm power gating state machine so it will wait till it receives
confirmation interrupt for the PG_ISOLATION_EXIT message.
In process of the suspend flow the devices first have to exit from the
power gating state (runtime pm resume).
If we do not handle the confirmation interrupt after sending
PG_ISOLATION_EXIT message, we may receive it already after the suspend
flow has changed the device state and interrupt will be interpreted as a
spurious event, consequently link reset will be invoked which will
prevent the device from completing the suspend flow
kernel: [6603] mei_reset:136: mei_me 0000:00:16.0: powering down: end of reset
kernel: [476] mei_me_irq_thread_handler:643: mei_me 0000:00:16.0: function called after ISR to handle the interrupt processing.
kernel: mei_me 0000:00:16.0: FW not ready: resetting
Cc: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=86241
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=770397
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d57f727264 upstream.
When auditing cmpxchg call sites, Chuck noted that gcc was optimizing
away some of the desired LDs.
| do {
| new = old = *ipi_data_ptr;
| new |= 1U << msg;
| } while (cmpxchg(ipi_data_ptr, old, new) != old);
was generating to below
| 8015cef8: ld r2,[r4,0] <-- First LD
| 8015cefc: bset r1,r2,r1
|
| 8015cf00: llock r3,[r4] <-- atomic op
| 8015cf04: brne r3,r2,8015cf10
| 8015cf08: scond r1,[r4]
| 8015cf0c: bnz 8015cf00
|
| 8015cf10: brne r3,r2,8015cf00 <-- Branch doesn't go to orig LD
Although this was fixed by adding a ACCESS_ONCE in this call site, it
seems safer (for now at least) to add compiler barrier to LLSC based
cmpxchg
Reported-by: Chuck Jordan <cjordan@synopsys.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2576c28e3f upstream.
- arch_spin_lock/unlock were lacking the ACQUIRE/RELEASE barriers
Since ARCv2 only provides load/load, store/store and all/all, we need
the full barrier
- LLOCK/SCOND based atomics, bitops, cmpxchg, which return modified
values were lacking the explicit smp barriers.
- Non LLOCK/SCOND varaints don't need the explicit barriers since that
is implicity provided by the spin locks used to implement the
critical section (the spin lock barriers in turn are also fixed in
this commit as explained above
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60df4642a8 upstream.
Make 3.81 doesn't have the 'undefine' command. Using undefine
to clear LDFLAGS fails when make version 3.81 is used. Fix it
to use override to clear LDFLAGS.
Tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Link: http://lkml.kernel.org/r/20150514151225.GH23588@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e2c70da9 upstream.
This id has been seen in the DSDT of the Teclast X98 Air 3G tablet based
on Intel Bay Trail.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d56402d3f upstream.
Add missing invocation of pm_generic_complete() to
acpi_subsys_complete() to allow ->complete callbacks provided
by the drivers of devices using the ACPI PM domain to be executed
during system resume.
Fixes: f25c0ae2b4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b064a8fa77 upstream.
Commit 73f7d1ca32 "ACPI / init: Run acpi_early_init() before
timekeeping_init()" moved the ACPI subsystem initialization,
including the ACPI mode enabling, to an earlier point in the
initialization sequence, to allow the timekeeping subsystem
use ACPI early. Unfortunately, that resulted in boot regressions
on some systems and the early ACPI initialization was moved toward
its original position in the kernel initialization code by commit
c4e1acbb35 "ACPI / init: Invoke early ACPI initialization later".
However, that turns out to be insufficient, as boot is still broken
on the Tyan S8812 mainboard.
To fix that issue, split the ACPI early initialization code into
two pieces so the majority of it still located in acpi_early_init()
and the part switching over the platform into the ACPI mode goes into
a new function, acpi_subsystem_init(), executed at the original early
ACPI initialization spot.
That fixes the Tyan S8812 boot problem, but still allows ACPI
tables to be loaded earlier which is useful to the EFI code in
efi_enter_virtual_mode().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=97141
Fixes: 73f7d1ca32 "ACPI / init: Run acpi_early_init() before timekeeping_init()"
Reported-and-tested-by: Marius Tolzmann <tolzmann@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4df3fd1700 upstream.
Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.
The fix is to ignore the non-HP sequencer checks.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7819717b11 upstream.
Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell
laptops to support the headset mic. The headset mic pin is 0x19 and
it's not exposed by BIOS, thus we need to fix the pincfg as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec56af67a1 upstream.
Thinkpad X250, when attached to a dock, has two headphone outs but
no line out. Make sure we don't try to turn this into one headphone
and one line out (since that disables the headphone amp on the dock).
Alsa-info at http://www.alsa-project.org/db/?f=36f8764e1d782397928feec715d0ef90dfddd4c1
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60b93030b4 upstream.
The pcm_class sysfs of each PCM substream gives only "none" since the
recent code change to embed the struct device. Fix the code to point
directly to the embedded device object properly.
Fixes: ef46c7af93 ('ALSA: pcm: Embed struct device')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fb22a8042 upstream.
Disable write buffering on the Toshiba ToPIC95 if it is enabled by
somebody (it is not supposed to be a power-on default according to
the datasheet). On the ToPIC95, practically no 32-bit Cardbus card
will work under heavy load without locking up the whole system if
this is left enabled. I tried about a dozen. It does not affect
16-bit cards. This is similar to the O2 bugs in early controller
revisions it seems.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961
Signed-off-by: Ryan C. Underwood <nemesis@icequake.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45c44b5ff9 upstream.
Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e91f8cb13 upstream.
If, at the time __rcu_process_callbacks() is invoked, there are callbacks
in Tiny RCU's callback list, but none of them are ready to be invoked,
the current list-management code will knit the non-ready callbacks out
of the list. This can result in hangs and possibly worse. This commit
therefore inserts a check for there being no callbacks that can be
invoked immediately.
This bug is unlikely to occur -- you have to get a new callback between
the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to
__rcu_process_callbacks(). It was detected by the addition of RCU-bh
testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's
mutation testing. Although this bug was made much more likely by
915e8a4fe4 (rcu: Remove fastpath from __rcu_process_callbacks()), this
did not cause the bug, but rather made it much more probable. That
said, it takes more than 40 hours of rcutorture testing, on average,
for this bug to appear, so this fix cannot be considered an emergency.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e749d7e1 upstream.
The CrystalCove GPIO irqchip doesn't have irq_set_wake callback defined
so we should set IRQCHIP_SKIP_SET_WAKE for it or it would cause an irq
desc's wake_depth unbalanced warning during system resume phase from the
gpio_keys driver, which is the driver for the power button of the ASUS
T100 laptop.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
