I was wrong about the TABLE_SIZE field description in the
commit 0676bfebf5 ("i3c: mipi-i3c-hci: Fix DAT/DCT entry sizes").
For the MIPI I3C HCI versions 1.0 and earlier the TABLE_SIZE field in
the registers DAT_SECTION_OFFSET and DCT_SECTION_OFFSET is indeed defined
in DWORDs and not number of entries like it is defined in later versions.
Where above fix allowed driver initialization to continue the wrongly
interpreted TABLE_SIZE field leads variables DAT_entries being twice and
DCT_entries four times as big as they really are.
That in turn leads clearing the DAT table over the boundary in the
dat_v1.c: hci_dat_v1_init().
So interprete the TABLE_SIZE field in DWORDs for HCI versions < 1.1 and
fix number of DAT/DCT entries accordingly.
Fixes: 0676bfebf5 ("i3c: mipi-i3c-hci: Fix DAT/DCT entry sizes")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
According to I3C Spec 1.1.1, 11-Jun-2021, section: 5.1.2.2.3:
If the Controller chooses to start an I3C Message with an I3C Dynamic
Address, then special provisions shall be made because that same I3C Target
may be initiating an IBI or a Controller Role Request. So, one of three
things may happen: (skip 1, 2)
3. The Addresses match and the RnW bits also match, and so neither
Controller nor Target will ACK since both are expecting the other side to
provide ACK. As a result, each side might think it had "won" arbitration,
but neither side would continue, as each would subsequently see that the
other did not provide ACK.
...
For either value of RnW: Due to the NACK, the Controller shall defer the
Private Write or Private Read, and should typically transmit the Target
^^^^^^^^^^^^^^^^^^^
Address again after a Repeated START (i.e., the next one or any one prior
^^^^^^^^^^^^^
to a STOP in the Frame). Since the Address Header following a Repeated
START is not arbitrated, the Controller will always win (see Section
5.1.2.2.4).
Resend target address again if address is not 7E and controller get NACK.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add hot-join support for dw i3c master controller.
By default, the hot-join acknowledgment is disabled, and the hardware will
automatically send the DISEC CCC when it receives the hot-join request.
Users can use the sys entry to enable it.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240429073624.256830-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Enable runtime PM for i3c master node during master registration time.
Sometimes i3c client device driver may want to control the PM of the
parent (master) to perform the transactions and save the power in an
efficient way by controlling the session. Hence device can call PM
APIs by passing the parent node.
Here, I3C target device when calls pm_runtime_get_sync(dev->parent)
couldn't invoke master drivers runtime PM callback registered by
the master driver because parent's PM status was disabled in the
Master node.
Also call pm_runtime_no_callbacks() and pm_suspend_ignore_children()
for the master node to not have any callback addition and ignore the
children to have runtime PM work just locally in the driver. This
should be generic and common change for all i3c devices and should
not have any other impact.
With these changes, I3C client device works and able to invoke
master driver registered runtime PM callbacks.
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20240228093407.4038399-1-quic_msavaliy@quicinc.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In an In-Band Interrupt (IBI) handle, the code logic is as follows:
1: writel(SVC_I3C_MCTRL_REQUEST_AUTO_IBI | SVC_I3C_MCTRL_IBIRESP_AUTO,
master->regs + SVC_I3C_MCTRL);
2: ret = readl_relaxed_poll_timeout(master->regs + SVC_I3C_MSTATUS, val,
SVC_I3C_MSTATUS_IBIWON(val), 0, 1000);
...
3: ibitype = SVC_I3C_MSTATUS_IBITYPE(status);
ibiaddr = SVC_I3C_MSTATUS_IBIADDR(status);
SVC_I3C_MSTATUS_IBIWON may be set before step 1. Thus, step 2 will return
immediately, and the I3C controller has not sent out the 9th SCL yet.
Consequently, ibitype and ibiaddr are 0, resulting in an unknown IBI type
occurrence and missing call I3C client driver's IBI handler.
A typical case is that SVC_I3C_MSTATUS_IBIWON is set when an IBI occurs
during the controller send start frame in svc_i3c_master_xfer().
Clear SVC_I3C_MSTATUS_IBIWON before issue SVC_I3C_MCTRL_REQUEST_AUTO_IBI
to fix this issue.
Cc: stable@vger.kernel.org
Fixes: 5e5e3c92e7 ("i3c: master: svc: fix wrong data return when IBI happen during start frame")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240506164009.21375-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
svc_i3c_master_xfer() returns error ENXIO if an In-Band Interrupt (IBI)
occurs when the host starts the frame.
Change error code to EAGAIN to inform the client driver that this
situation has occurred and to try again sometime later.
Fixes: 5e5e3c92e7 ("i3c: master: svc: fix wrong data return when IBI happen during start frame")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240506164009.21375-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In accordance with I3C spec ver 1.1.1 09-Jun-2021, section: 5.1.2.2.3, if
a target requests hot join (HJ), In-Band Interrupt (IBI), or controller
role request (CRR) during the emission of an I3C address in
i3c_device_do_priv_xfers(), the target may win bus arbitration. In such
cases, it is imperative to notify the I3C client driver and retry
i3c_device_do_priv_xfers() after some delay.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240506164009.21375-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since commit d492cc2573 ("driver core: device.h: make struct
bus_type a const *"), the driver core can properly handle constant
struct bus_type, move the i3c_bus_type variable to be a constant
structure as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240213-bus_cleanup-i3c-v1-1-403aea18f05a@marliere.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Disable IBI IRQ signal and status only when hot-join and SIR enabling of
all target devices attached to the bus are disabled.
Fixes: e389b1d72a ("i3c: dw: Add support for in-band interrupts")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Link: https://lore.kernel.org/r/20240119054547.983693-1-dylan_hung@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As per the Cadence IP document fixed the I2C clock divider value limit from
16 bits instead of 10 bits. Without this change setting up the I2C clock to
low frequencies will not work as the prescaler value might be greater than
10 bit number.
I3C clock divider value is 10 bits only. Updating the macro names for both.
Signed-off-by: Harshit Shah <harshitshah.opendev@gmail.com>
Link: https://lore.kernel.org/r/1703927483-28682-1-git-send-email-harshitshah.opendev@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C allow devices early terminate data transfer. So set "actual_len" to
indicate how much data get by i3c_priv_xfer.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C transfer (SDR), target can early terminate read transfer.
I3C transfer (HDR), target can end write transfer.
I2C transfer, target can NACK write transfer.
'actual_len' is better name than 'read_len'.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-5-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add hot join support for svc master controller. Disable hot join by
default.
User can use sysfs entry to enable hot join.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add hotjoin entry in sys file system allow user enable/disable hotjoin
feature.
Add (*enable(disable)_hotjoin)() to i3c_master_controller_ops.
Add api i3c_master_enable(disable)_hotjoin();
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some I3C hardware will report error when an incorrect length is received from
device. GETMXDS CCC are available in 2 formats: without turnaround time (format
1) and with turnaround time (format 2). There is no mechanics to determine which
format is supported by device. So in case sending GETMXDS CCC format 2 resulted
in a failure, try sending GETMXDS CCC format 1 instead.
Signed-off-by: Joshua Yeong <joshua.yeong@starfivetech.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231114085525.6271-2-joshua.yeong@starfivetech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement a local bounce buffer for private I3C SDR and I2C transfers
when using DMA and the buffer attached to the transfer is not DMA safe.
Otherwise the DMA transfer will fail and with following warning:
[ 11.411059] i3c mipi-i3c-hci.0: rejecting DMA map of vmalloc memory
[ 11.417313] WARNING: CPU: 3 PID: 357 at include/linux/dma-mapping.h:332 hci_dma_queue_xfer+0x2e2/0x300 [mipi_i3c_hci]
Strictly speaking private I3C SDR transfers are expected to pass a
DMA-able buffer. However I fear this requirement may easily be slipped
or go unnoticed when I3C interface support is added into a existing
device driver that use regmap API to read/write stack variables.
For example this is the case with the commit 2660b0080b ("iio: imu:
st_lsm6dsx: add i3c basic support for LSM6DSO and LSM6DSR").
Buffer of an I2C message is not required to be DMA safe and the I2C core
provides i2c_(get|put)_dma_safe_msg_buf() helpers for the host
controllers that do DMA and that is also recommendation for the
i2c_xfers() callback from the I3C core.
However due to above I3C private transfers reason I decided to implement
a bounce buffer for them and reuse the same code for the I2C transfers
too. Since this driver is currently the only I3C host controller driver
that can do DMA the implementation is done here and not in I3C core.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Handle also I3C address header error response status as the end of DAA
process in hci_cmd_v1_daa().
According to MIPI I3C HCI Specification v1.1 the NACK error during DAA
process comes when the device does not accept the dynamic address.
Currently code uses it for successful exit from the process and fails
with any other error response.
I'm unsure is this MIPI I3C HCI version specific difference or
specification misunderstanding but on an early MIPI I3C HCI version
compatible controller responds always with I3C address header error and
not with NACK error when there is no device on the bus or no more devices
participating to DAA process.
Handle now both response statuses as the end of DAA.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Function hci_cmd_v1_daa() uses only single transfer at a time so no need
to allocate two transfers and access can be simplified.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Currently probe of mipi-i3c-hci will fail if bus doesn't have any I3C
devices connected. This happens when CCC commands that are sent during
i3c_master_bus_init() are not ACKed by any device and controller responds
with an error status set.
The controller can detect NACK both during I3C address header
transmission (broadcast address 0x7e is not ACKed) and when target
device address or dynamic address assignment is NACKed. Former as error
status 0x4: Address Header Error and latter as 0x5: NACK.
Difference between those two NACK statuses were not described explicitly
until MIPI I3C HCI Specification v1.1. Earlier versions share the same
error status code though.
Report both of those as I3C_ERROR_M2 to I3C core code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually tested
- svc: many IBI fixes, correct compatible string, fix hot join corner cases
-----BEGIN PGP SIGNATURE-----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=rFcf
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"There are now more fixes because as stated in my previous pull
request, people now have access to actual hardware.
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually
tested
- svc: many IBI fixes, correct compatible string, fix hot join corner
cases"
* tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (29 commits)
i3c: master: handle IBIs in order they came
i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
i3c: master: svc: fix compatibility string mismatch with binding doc
i3c: master: svc: fix random hot join failure since timeout error
i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
i3c: master: svc: fix check wrong status register in irq handler
i3c: master: svc: fix ibi may not return mandatory data byte
i3c: master: svc: fix wrong data return when IBI happen during start frame
i3c: master: svc: fix race condition in ibi work thread
i3c: Fix typo "Provisional ID" to "Provisioned ID"
i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
i3c: mipi-i3c-hci: Resume controller after aborted transfer
i3c: mipi-i3c-hci: Resume controller explicitly
i3c: mipi-i3c-hci: Fix missing xfer->completion in hci_cmd_v1_daa()
i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
i3c: mipi-i3c-hci: Set number of SW enabled Ring Bundles earlier
i3c: mipi-i3c-hci: Fix race between bus cleanup and interrupt
i3c: mipi-i3c-hci: Set ring start request together with enable
i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
...
IBI shall be handled in order they appear on the bus. Otherwise could hit
case when order of handling them in device driver will be different. It may
lead to invalid assembling fragmented packets or events order broken.
Added separate workqueue with option WQ_MEM_RECLAIM for each device driver.
This ensures IBI handling order and improves IBI handling performance: IBI
handlers for device B are not blocked by IBI handlers for device A.
Original solution (single workqueue in main driver) was able to handle also
general IBI (not related to specific device) like HJ or MR. So leaving this
for such purposes.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/20231015222334.1652401-2-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The `i3c_master_bus_init` function may attach the I2C devices before the
I3C bus initialization. In this flow, the DAT `alloc_entry`` will be used
before the DAT `init`. Additionally, if the `i3c_master_bus_init` fails,
the DAT `cleanup` will execute before the device is detached, which will
execue DAT `free_entry` function. The above scenario can cause the driver
to use DAT_data when it is NULL.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20231023080237.560936-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the binding documentation, the compatible string is specified as
'silvaco,i3c-master-v1', but in the driver, it is defined as
'silvaco,i3c-master'.
Rename 'silvaco,i3c-master' to 'silvaco,i3c-master-v1' to ensure
compatibility with the documentation.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231017194657.3199749-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
master side report:
silvaco-i3c-master 44330000.i3c-master: Error condition: MSTATUS 0x020090c7, MERRWARN 0x00100000
BIT 20: TIMEOUT error
The module has stalled too long in a frame. This happens when:
- The TX FIFO or RX FIFO is not handled and the bus is stuck in the
middle of a message,
- No STOP was issued and between messages,
- IBI manual is used and no decision was made.
The maximum stall period is 100 μs.
This can be considered as being just a warning as the system IRQ latency
can easily be greater than 100us.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-7-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Upon IBIWON timeout, the SDA line will always be kept low if we don't emit
a stop. Calling svc_i3c_master_emit_stop() there will let the bus return to
idle state.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
MSTATUS[RXPEND] is only updated after the data transfer cycle started. This
creates an issue when the I3C clock is slow, and the CPU is running fast
enough that MSTATUS[RXPEND] may not be updated when the code reaches
checking point. As a result, mandatory data can be missed.
Add a wait for MSTATUS[COMPLETE] to ensure that all mandatory data is
already in FIFO. It also works without mandatory data.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-4-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
┌─────┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┌─────
SCL: ┘ └─────┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┘
───┐ ┌─────┐ ┌─────┐ ┌───────────┐
SDA: └───────────────────────┘ └─────┘ └─────┘ └─────
xxx╱ ╲╱ ╲╱ ╲╱ ╲╱ ╲
: xxx╲IBI ╱╲ Addr(0x0a) ╱╲ RW ╱╲NACK╱╲ S ╱
If an In-Band Interrupt (IBI) occurs and IBI work thread is not immediately
scheduled, when svc_i3c_master_priv_xfers() initiates the I3C transfer and
attempts to send address 0x7e, the target interprets it as an
IBI handler and returns the target address 0x0a.
However, svc_i3c_master_priv_xfers() does not handle this case and proceeds
with other transfers, resulting in incorrect data being returned.
Add IBIWON check in svc_i3c_master_xfer(). In case this situation occurs,
return a failure to the driver.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ibi work thread operates asynchronously with other transfers, such as
svc_i3c_master_priv_xfers(). Introduce mutex protection to ensure the
completion of the entire i3c/i2c transaction.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This allows other drivers to be notified when new i3c busses are
attached, referring to a whole i3c bus as opposed to individual
devices.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The MIPI I3C spec refers to a Provisioned ID, since it is (sometimes)
provisioned at device manufacturing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231003075339.197099-1-matt@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
put_device() needs to be called on failure of device_register()
to give up the reference initialized in it to avoid refcount leak.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20230921082410.25548-1-dinghao.liu@zju.edu.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Host Controller goes to halt state after aborted transfer and needs to
be resumed by SW. Add this resuming to DMA mode code too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-13-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On an HW I'm using in enabling work the RESUME bit is not set in the
HC_CONTROLLER register when Host Controller goes to halt state. Value 1
should mean controller is suspended when reading and writing 1 resumes it.
Because of this erratic behaviour plain HC_CONTROL read and write back
won't resume the controller. Therefore do it by setting the RESUME bit
explicitly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-12-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Due to missing completion object for the ENTDAA command transfer in the
hci_cmd_v1_daa() the wait_for_completion_timeout() will obviously
timeout even the transfer itself may succeed.
Fix this by setting the xfer->completion to the already initialized
completion object.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-11-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix following warning (with CONFIG_DMA_API_DEBUG) which happens with a
transfer without a data buffer.
DMA-API: i3c mipi-i3c-hci.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=0 bytes]
For those transfers the hci_dma_queue_xfer() doesn't create a mapping and
the DMA address pointer xfer->data_dma is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-10-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Number of software enabled Ring Bundles must be set before using them.
Otherwise Ring will not start and may be power-gated by the Host
Controller.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-9-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If there is a transfer error during i3c_master_bus_init() and code goes
doing the bus cleanup in i3c_hci_bus_cleanup() there is possibility that
i3c_hci_irq_handler() is running in parallel with hci->io->cleanup()
which can be racy.
Prevent this by waiting there is no pending interrupt on other CPU
before doing the IO cleanup.
This was observed with ring headers where first transfer failed and
sometimes transfer error or ring transfer abort interrupt was coming
simultaneously with the bus cleanup path.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-8-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Set ring start request together with ring enable in hci_dma_init(). This
causes the ring abort request in hci_dma_dequeue_xfer() will raise the
INTR_RING_OP (RING_OP_STAT in MIPI I3C HCI specification) interrupt in
the RH_INTR_STATUS register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-7-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ring Abort request will timeout in case there is an error in the Host
Controller interrupt delivery or Ring Header configuration. Using BUG()
makes hard to debug those cases.
Make it less severe and turn BUG() to WARN_ON().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-6-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Do not loop over ring headers in hci_dma_irq_handler() that are not
allocated and enabled in hci_dma_init(). Otherwise out of bounds access
will occur from rings->headers[i] access when i >= number of allocated
ring headers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
MIPI I3C HCI specification v1.1 describes the ENTRY_SIZE field for the
Device Address Table (DAT) and the Device Characteristics Table (DCT)
section offset registers (DAT_SECTION_OFFSET and DCT_SECTION_OFFSET).
That field is not documented in earlier version.
ENTRY_SIZE value 0 is meant to be backward compatible. For the DAT entry
size it is interpreted as 2 DWORDs (8-bytes) and for the DCT entry size
as 4 DWORDs (16-bytes). Values 1-15 are reserved for future use.
New version I believe fixes also the TABLE_SIZE field description.
Before it was defined in DWORDs which I believe is incorrect since the
DAT/DCT table entry structures, and sizes, are described having
8-bytes/16-bytes entries.
This is more clear in the specification v1.1 which states the TABLE_SIZE
fields are interpreted as number of entries in the DAT/DCT tables. I
believe this same holds also in earlier version, at least it makes more
sense.
Fix code accordingly and let the DAT_entry_size and the DCT_entry_size
variables carry the size as bytes. Which is how it is already
interpreted in the dat_v1.c: hci_dat_v1_init().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add MODULE_ALIAS() in order to be able to autoload this driver when the
device is added as a platform device from another glue code driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Copy the DMA masks and parameters for an I3C master device from parent
device so that the master device has them set for the DMA buffer and
mapping API.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct svc_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Conor Culhane <conor.culhane@silvaco.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922175023.work.239-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hci_rings_data.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: Len Baker <len.baker@gmx.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175019.work.129-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cdns_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: "Przemysław Gaj" <pgaj@cadence.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175014.work.637-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct dw_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230922175011.work.800-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
We should prefer more robust and less ambiguous string interfaces.
We expect adap->name to be NUL-terminated based on i2c_adapter name use:
| dev_dbg(&adap->dev, "adapter [%s] registered\n", adap->name);
NUL-padding does not seem to be required as `master` is zero-allocated
and `i3c_master_to_i2c_adapter` simply returns a field from within
`master`:
| master = devm_kzalloc(dev, sizeof(*master), GFP_KERNEL);
...
| struct i2c_adapter *adap = i3c_master_to_i2c_adapter(master);
...
| static struct i2c_adapter *
| i3c_master_to_i2c_adapter(struct i3c_master_controller *master)
| {
| return &master->i2c;
| }
This means that `adap->name` should already be filled with NUL-bytes.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230921-strncpy-drivers-i3c-master-c-v1-1-9fdb8d8169e1@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C masters are expected to support hot-join. This means at initialization
time we might not yet discover any device and this should not be treated
as a fatal error.
During the DAA procedure which happens at probe time, if no device has
joined, all CCC will be NACKed (from a bus perspective). This leads to an
early return with an error code which fails the probe of the master.
Let's avoid this by just telling the core through an I3C_ERROR_M2
return command code that no device was discovered, which is a valid
situation. This way the master will no longer bail out and fail to probe
for a wrong reason.
Cc: stable@vger.kernel.org
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230831141324.2841525-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When a I3C DT node has a static_addr and an init_dyn_addr,the
init_dyn_addr is reserved in i3c_master_bus_init() and then
the static_addr is reserved in i3c_master_early_i3c_dev_add().
But if the dynamic address is same as static then above
procedure would fail.
Add a check to pass i3c_bus_get_addr_slot_status() when static
and dynamic address are equal.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20230822051938.2852567-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 'saved_regs' member of the 'svc_i3c_master' structure is not
described in the kernel doc, which produces the following warning:
Function parameter or member 'saved_regs' not described in 'svc_i3c_master'
Add the missing line in the kernel documentation of the parent
structure.
Fixes: 1c5ee2a77b ("i3c: master: svc: fix i3c suspend/resume issue")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171435.0xQ82lvu-lkp@intel.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230817101853.16805-1-miquel.raynal@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230803085149.149248-1-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The exit criteria for the DAA should check if the data length is equal to
1, instead of checking if the response status is equal to 1.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20230802100909.2568215-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230714174623.4057784-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add NACK check after start byte is sent.
It is possible to detect early that a device is not on the bus
and avoid invalid transmissions thereafter.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-3-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
pm_runtime_resume_and_get() may call sleep(). It cannot be used in
svc_i3c_master_start_xfer_locked(), because it is in a spin lock.
Move the pm runtime operations to svc_i3c_master_enqueue_xfer().
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Fixes: 05be23ef78 ("i3c: master: svc: add runtime pm support")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-2-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When system suspends, if i3c module is powered down, register
value will lose.
Need to save the key registers before system suspend.
So save these registers value in runtime pm suspend, and restore them
if these register's value is different with the saved values
when runtime pm resume.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-1-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
smatch reports
drivers/i3c/master/ast2600-i3c-master.c:121:34: warning: symbol
'ast2600_i3c_ops' was not declared. Should it be static?
This variable is only used in its defining file, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230429134601.2688558-1-trix@redhat.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 2k register setting is zero, OR-ing it in doesn't parallel the 2k
and 750 ohm pullups. We need a separate value for the 545 ohm setting.
Reported-by: Lukwinski Zbigniew <zbigniew.lukwinski@linux.intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230428001849.1775559-1-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ast2600 i3c hardware is capable of IBIs, but we need a workaround
for a hardware issue with the I3C state machine handling IBI payloads
of specific lengths when PEC is not enabled. To avoid this, we need to
unconditionally enable PECs, at the consquence of losing a byte of data
when the device does not send a PEC.
Enable IBIs on the ast2600 platform, including an implementation of the
PEC workaround, which prints a warning when triggered.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/ba923b96d6d129024c975e8a0472c5b2fcb3af32.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On the AST2600 i3c controller, we'll need to apply a workaround for a
hardware issue with IBI payloads.
Introduce a platform hook to allow dw i3c platform implementations to
modify the DAT entry in IBI enable/disable to allow this workaround in a
future change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/d5d76a8d2336d2a71886537f42e71d51db184df6.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This change adds support for receiving and dequeueing i3c IBIs.
By setting struct dw_i3c_master->ibi_capable before probe, a platform
implementation can select the IBI-enabled version of the i3c_master_ops,
enabling the global IBI infrastrcture for that controller.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/79daeefd7ccb7c935d0c159149df21a6c9a73ffa.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In an upcoming change, we will want to store additional data about the
devices we have in the data address table.
Change the type of the DAT entries into a struct, which currently just
has the address data.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/9dc0d9e2857e851a0cf04819df48e5d31921f83e.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In a future change we'll want to read from the IBI FIFO too, so turn
dw_i3c_read_rx_fifo() into a generic read with the FIFO register as a
parameter.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/827204789583dd86addffb47ecaeab9d67cf95d5.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Parse the /aliases node to assign any fixed bus numbers, as is done with
the i2c subsystem. Numbering for non-aliased busses will start after the
highest fixed bus number.
This allows an alias node such as:
aliases {
i3c0 = &bus_a,
i3c4 = &bus_b,
};
to set the numbering for a set of i3c controllers:
/* fixed-numbered bus, assigned "i3c-0" */
bus_a: i3c-master {
};
/* another fixed-numbered bus, assigned "i3c-4" */
bus_b: i3c-master {
};
/* dynamic-numbered bus, likely assigned "i3c-5" */
bus_c: i3c-master {
};
If no i3c device aliases are present, the numbering will stay as-is,
starting from 0.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230405094149.1513209-1-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Now that we have platform-specific infrastructure for the dw i3c driver,
add platform support for the ASPEED AST2600 SoC.
The AST2600 has a small set of "i3c global" registers, providing
platform-level i3c configuration outside of the i3c core.
For the ast2600, we need a couple of extra setup operations:
- on probe: find the i3c global register set and parse the SDA pullup
resistor values
- on init: set the pullups accordingly, and set the i3c instance IDs
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230331091501.3800299-4-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The dw i3c core can be integrated into various SoC devices. Platforms
that use this core may need a little configuration that is specific to
that platform.
Add some infrastructure to allow platform-specific behaviour: common
probe/remove functions, a set of platform hook operations, and a pointer
for platform-specific data in struct dw_i3c_master. Move the common api
into a new (i3c local) header file.
Platforms will provide their own struct platform_driver, which allocates
struct dw_i3c_master, does any platform-specific probe behaviour, and
calls into the common probe.
A future change will add new platform support that uses this
infrastructure.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230331091501.3800299-2-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the clock setup path, we set the hardware DEV_CTRL_I2C_SLAVE_PRESENT
bit on a shared mode bus, then read-back this bit for the conditional
tCAS set.
Instead, just use the bus->mode setting for the conditional test.
While we're at it, add a little comment about why the conditional is
there.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/92a933566f7846708a00ad7f5a16ee8e6ed32d0e.1680156630.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We currently assume that the rx_len of a read command will be as
submitted, but we may have a shorter read than expected.
This change populates the output i3c xfer length from the actually-read
length.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/f4fff7ab18dee1f662dc7a5a4111fcd921e6792b.1680156630.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230318233311.265186-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230318233311.265186-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230318233311.265186-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230318233311.265186-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function returned zero unconditionally. Switch the return type to void
and simplify the callers accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230318233311.265186-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/i3c/master/dw-i3c-master.c:1201:34: error: ‘dw_i3c_master_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312132535.352246-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- transfer pid from boardinfo to device info
Drivers:
- dw-i3c-master: stop hardcoding initial speed
-----BEGIN PGP SIGNATURE-----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=CEs9
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Subsystem:
- transfer pid from boardinfo to device info
Drivers:
- dw-i3c-master: stop hardcoding initial speed"
* tag 'i3c/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw: stop hardcoding initial speed
i3c: transfer pid from boardinfo to device info
Bus-speed could be default(12.5MHz) or defined by users in dts.
Dw-i3c-master should not hard-code the initial speed to be
I3C_BUS_TYP_I3C_SCL_RATE (12.5MHz)
And because of Synopsys's I3C controller limit (hcnt/lcnt register
length) and core-clk provided, there is a limit to bus speed, too.
For example, when core-clk is 250 MHz, the bus speed cannot be
lowered below 1MHz.
Tested: tested with an i3c sensor and captured with a logic analyzer.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20230216151057.293764-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C device PID could be defined in device tree and stored in
i3c_dev_boardinfo. It should be passed to i3c_device_info when
allocating a i3c_dev_desc.
Rational behind this change is: when users decide to use SETDASA to
assign a dynamic address with exactly the original static address, in
step of i3c_master_reattach_i3c_dev, this address is checked to be
taken. Then device information retrieving step is skipped. As a result,
though the i3c device is registered correctly, its device driver could
not be probed.
Tested: Tested with a I3C device. If assigned-address is set to be the
device's static address, without this change, its device driver could
not probed. And with this change, its driver is probed successfully.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20230105212952.56321-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core is changing to pass some pointers as const, so move
dev_to_i3cdev() to use container_of_const() to handle this change.
dev_to_i3cdev() now properly keeps the const-ness of the pointer passed
into it, while as before it could be lost.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because not all I3C drivers have the hot-join feature ready, and
especially not all I3C devices support hot-join feature, exporting
SETDASA method could be useful. With this function, the I3C controller
could perform a DAA to I3C devices when users decide to turn these I3C
devices off and on again during run-time.
Tested: This change has been tested with turnning off an I3C device and
turning on it again during run-time. The device driver calls SETDASA
method to perform DAA to the device. And communication between I3C
controller and device is set up again correctly.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20221207205059.3848851-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The reattach should be used when an I3C device has its address changed.
But the modified place in this patch doesn't have the address changed of
the newdev. This wrong reattach will reserve the same address slot twice
and return unexpected -EBUSY when the bus find the duplicate device with
diffent dynamic address.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20220926105145.8145-2-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch is used to free the old_dyn_addr when the caller want to
reattach the device to the different dynamic address. If the
old_dyn_addr is 0 the function will treat it as no old_dyn_addr is
reserved on the bus. Without the patch, when the driver reattach the i3c
device after setnewda the old_dyn_addr will be permanently occupied.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20220926105145.8145-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Commit 31b9887c72 ("i3c: remove i2c board info from i2c_dev_desc")
removed the boardinfo from i2c_dev_desc to decouple device enumeration from
setup but did not correctly lookup the i2c_dev_desc to store the new
device, instead dereferencing an uninitialized variable.
Lookup the device that has already been registered by address to store
the i2c client device.
Fixes: 31b9887c72 ("i3c: remove i2c board info from i2c_dev_desc")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220308134226.1042367-1-quic_jiles@quicinc.com
I2C devices can be added to the system dynamically through several
sources other than static board info including device tree overlays and
sysfs i2c new_device.
Add an I2C bus notifier to attach the clients at runtime if they were
not defined in the board info. For DT devices find the LVR in the reg
property, for user-space new_device additions we synthesize a
conservative setting of no spike filters and fast mode only.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220117174816.1963463-3-quic_jiles@quicinc.com
I2C board info is only required during adapter setup so there is no
requirement to keeping a pointer to it once running. To support dynamic
device addition we can't rely on board info - user-space creation
through sysfs won't have a boardinfo.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220117174816.1963463-2-quic_jiles@quicinc.com
Clang static analysis reports this problem
dw-i3c-master.c:799:9: warning: The result of the left shift is
undefined because the left operand is negative
COMMAND_PORT_DEV_INDEX(pos) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~
pos can be negative because dw_i3c_master_get_free_pos() can return an
error. So check for an error.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220108150948.3988790-1-trix@redhat.com
The referred config BIG_ENDIAN does not exist. The config for the
endianness of the CPU architecture is called CPU_BIG_ENDIAN.
Correct the config name to the existing config for the endianness.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220103094504.3602-1-lukas.bulwahn@gmail.com
If enable interrupt in the svc_i3c_master_bus_init() but do not call
enable ibi in the device driver, it will cause a kernel dump in the
svc_i3c_master_handle_ibi() when a slave start occurs on the i3c bus,
because the data->ibi_pool is not initialized.
So only enable the interrupt in svc_i3c_master_enable_ibi() function.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-9-xiaoning.wang@nxp.com
The missing MODULE_DEVICE_TABLE() will cause the svc-i3c-master cannot
be auto probed when it is built in moudle.
So add it.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-8-xiaoning.wang@nxp.com
Add runtime pm support to dynamically manage the clock.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-7-xiaoning.wang@nxp.com
If using I2C/I3C mixed mode, need to set ODSTOP. Otherwise, the I2C
devices cannot see the stop signal. It may cause message sending errors.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-6-xiaoning.wang@nxp.com
When i3c controller reads data from slave device, slave device can stop
returning data with an ACK after any byte.
Add this support for svc i3c controller. Otherwise, it will timeout
when the slave device ends the read operation early.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-5-xiaoning.wang@nxp.com
Sometimes only need to reset err and fifo regs, so split the origin
reset function to three functions.
Put them at the top of the file, to let more functions can call them.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211227074529.1660398-4-xiaoning.wang@nxp.com
