The i2c-ocores controller can run in interrupt mode on tqmx86 modules.
Add a module parameter to allow configuring the IRQ number, similar to the
handling of the GPIO IRQ.
The new code and module parameter refer to the I2C controller as "I2C1",
as the TQMx86 PLD actually contains a second I2C controller, for which
driver support will be added in the future.
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/c1b0769e00a8a4e463cffe725e939b0e5c2992c8.1731325758.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Lee Jones <lee@kernel.org>
GPIO IRQ setup can fail either because an invalid IRQ was passed as a
parameter, or because the GPIO controller does not support interrupts.
Neither is severe enough to stop the whole probe; simply disable IRQ
support in the GPIO resource when setup fails.
The code is made a bit more robust by introduing an enum for the
resource list indices instead of assuming that the IRQ is at index 0.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/2b5522362098d54c6203be6da95bbc545a21fd49.1731325758.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Lee Jones <lee@kernel.org>
Move IRQ setup into a helper function. The string "GPIO" for error
messages is replaced with a label argument to prepare for reusing the
function for the I2C IRQ.
No functional change intended.
Co-developed-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/97f481334f480a113b7076e76f994e0e73ee5aa5.1731325758.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Lee Jones <lee@kernel.org>
It seems that this driver was developed based on preliminary documentation.
Report the correct names for all TQMxE39x variants, as they are used by
the released hardware revisions:
- Fix names for TQMxE39C1/C2 board IDs
- Distinguish TQMxE39M and TQMxE39S, which use the same board ID
The TQMxE39M/S are distinguished using the SAUC (Sanctioned Alternate
Uses Configuration) register of the GPIO controller. This also prepares
for the correct handling of the differences between the GPIO controllers
of our COMe and SMARC modules.
Fixes: 2f17dd34ffed ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/aca9a7cb42a85181bcb456c437554d2728e708ec.1676892223.git.matthias.schiffer@ew.tq-group.com
Registers 0x160..0x17f are unassigned. Use 0x180 as base register and
update offets accordingly.
Also change the size of the range to include 0x19f. While 0x19f is
currently reserved for future extensions, so are several of the previous
registers up to 0x19e, and it is weird to leave out just the last one.
Fixes: 2f17dd34ffed ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/db4677ac318b1283c8956f637f409995a30a31c3.1676892223.git.matthias.schiffer@ew.tq-group.com
The I2C_DETECT register is at IO port 0x1a7, which is outside the range
passed to devm_ioport_map() for io_base, and was only working because
there aren't actually any bounds checks for IO port accesses.
Extending the range does not seem like a good solution here, as it would
then conflict with the IO resource assigned to the I2C controller. As
this is just a one-off access during probe, use a simple inb() instead.
While we're at it, drop the unused define TQMX86_REG_I2C_INT_EN.
Fixes: 2f17dd34ffed ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/e8300a30f0791afb67d79db8089fb6004855f378.1676892223.git.matthias.schiffer@ew.tq-group.com
All future TQMx86 modules should use a 24MHz LPC clock. Warn about
unknown boards, but assume this is the case.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer TQMx86 modules use TQ-Systems instead of TQ-Group as their vendor
ID.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the board IDs for the TQMx110EB and the TQMxE40x family. All use a
24MHz LPC clock.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rename variable from "ocores_platfom_data" to "ocores_platform_data".
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
No TQMx90UC exists at the moment, and it is undecided whether ID 10 will
be used eventually (and if it is, how that SoM will be named).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ffed ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Based on the file name and code of the driver, it is likely that this
module is related to TQMx86 and not TQx86.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mfd/tqmx86.c: In function ‘tqmx86_probe’:
drivers/mfd/tqmx86.c:161:29: warning: variable ‘i2c_ien’
set but not used I[-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The QMX86 is a PLD present on some TQ-Systems ComExpress modules. It
provides 1 or 2 I2C bus masters, 8 GPIOs and a watchdog timer. Add an
MFD which will instantiate the individual drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
