asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
An abort that is responded to by iSCSI itself is added to tmr_list but does
not go to target core. A LUN_RESET that goes through tmr_list takes a
refcounter on the abort and waits for completion. However, the abort will
be never complete because it was not started in target core.
Unable to locate ITT: 0x05000000 on CID: 0
Unable to locate RefTaskTag: 0x05000000 on CID: 0.
wait_for_tasks: Stopping tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
wait for tasks: tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
...
INFO: task kworker/0:2:49 blocked for more than 491 seconds.
task:kworker/0:2 state:D stack: 0 pid: 49 ppid: 2 flags:0x00000800
Workqueue: events target_tmr_work [target_core_mod]
Call Trace:
__switch_to+0x2c4/0x470
_schedule+0x314/0x1730
schedule+0x64/0x130
schedule_timeout+0x168/0x430
wait_for_completion+0x140/0x270
target_put_cmd_and_wait+0x64/0xb0 [target_core_mod]
core_tmr_lun_reset+0x30/0xa0 [target_core_mod]
target_tmr_work+0xc8/0x1b0 [target_core_mod]
process_one_work+0x2d4/0x5d0
worker_thread+0x78/0x6c0
To fix this, only add abort to tmr_list if it will be handled by target
core.
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Link: https://lore.kernel.org/r/20240111125941.8688-1-d.bogdanov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kernel-doc comment to silence the warnings:
drivers/target/target_core_transport.c:1930: warning: Excess function parameter 'cmd' description in 'target_submit'
drivers/target/target_core_transport.c:1930: warning: Function parameter or member 'se_cmd' not described in 'target_submit'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6844
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231017030913.89973-1-yang.lee@linux.alibaba.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mike Christie <michael.christie@oracle.com> says:
The following patches were made over Linus's tree but apply over
Martin's branches. They allow userspace to configure how fabric
drivers submit cmds to backend drivers.
Right now loop and vhost use a worker thread, and the other drivers
submit from the contexts they receive/process the cmd from. For
multiple LUN cases where the target can queue more cmds than the
backend can handle then deferring to a worker thread is safest because
the backend driver can block when doing things like waiting for a free
request/tag. Deferring also helps when the target has to handle
transport level requests from the recv context.
For cases where the backend devices can queue everything the target
sends, then there is no need to defer to a workqueue and you can see a
perf boost of up to 26% for small IO workloads. For a nvme device and
vhost-scsi I can see with 4K IOs:
fio jobs 1 2 4 8 10
--------------------------------------------------
workqueue
submit 94K 190K 394K 770K 890K
direct
submit 128K 252K 488K 950K -
Link: https://lore.kernel.org/r/1b1f7a5c-0988-45f9-b103-dfed2c0405b1@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This allows userspace to request the fabric drivers do direct submissions
if they support it. With the new device file, submit_type, users can
write 0 - 2 to control how commands are submitted to the backend:
0 - TARGET_FABRIC_DEFAULT_SUBMIT - LIO will use the fabric's default
submission type. This is the default for compat.
1 - TARGET_DIRECT_SUBMIT - LIO will submit the cmd to the backend from the
calling context if the fabric the cmd was received on supports it,
else it will use the fabric's default type.
2 - TARGET_QUEUE_SUBMIT - LIO will queue the cmd to the LIO submission
workqueue which will pass it to the backend.
When using an NVMe drive and vhost-scsi with direct submission we see
around a 20% improvement in 4K I/Os:
fio jobs 1 2 4 8 10
--------------------------------------------------
defer 94K 190K 394K 770K 890K
direct 128K 252K 488K 950K -
And when using the queueing mode, we now no longer see issues like where
the iSCSI tx thread is blocked in the block layer waiting on a tag so it
can't respond to a nop or perform I/Os for other LUs.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230928020907.5730-6-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the code from transport_handle_cdb_direct() to target_submit() and
have iSCSI call target_submit().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230928020907.5730-5-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the hack to clear some buffers to transport_handle_cdb_direct() so we
can eventually merge transport_handle_cdb_direct() and target_submit().
This also fixes up the comment so it's clear it was only for udev and
reflects that the referenced function does not exist and we now allow more
than 1 page for control CDBs.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230928020907.5730-4-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move core_alua_check_nonop_delay() to transport_handle_cdb_direct() so the
iSCSI target driver doesn't have to call as many core functions
directly. We will eventually merge transport_handle_cdb_direct and
target_submit so iSCSI and the other drivers call a common function.
It will also be helpful as preparation for future changes which allow the
iSCSI target to defer command submission to the LIO submission workqueue,
because we will have a common submission function for that which will be
based on transport_handle_cdb_direct()/target_submit().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230928020907.5730-3-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the error exits in target_setup_session(), if a branch is taken to
free_sess: transport_free_session() may call to target_free_cmd_counter()
and then fall through to call target_free_cmd_counter() a second time.
This can, and does, sometimes cause seg faults since the data field in
cmd_cnt->refcnt has been freed in the first call.
Fix this problem by simply returning after the call to
transport_free_session(). The second call is redundant for those cases.
Fixes: 4edba7e4a8 ("scsi: target: Move cmd counter allocation")
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Link: https://lore.kernel.org/r/20230613144259.12890-1-rpearsonhpe@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This has iscsit allocate a per conn cmd counter and converts iscsit/isert
to use it instead of the per session one.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-5-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow target_get_sess_cmd() users to pass in the cmd counter they want to
use. Right now we pass in the session's cmd counter but in a subsequent
commit iSCSI will switch from per session to per conn.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-4-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iSCSI needs to allocate its cmd counter per connection for MCS support
where we need to stop and wait on commands running on a connection instead
of per session. This moves the cmd counter allocation to
target_setup_session() which is used by drivers that need the stop+wait
behavior per session.
xcopy doesn't need stop+wait at all, so we will be OK moving the cmd
counter allocation outside of transport_init_session().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-3-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iSCSI needs to wait on outstanding commands like how SRP and the FC/FCoE
drivers do. It can't use target_stop_session() because for MCS support we
can't stop the entire session during recovery because if other connections
are OK then we want to be able to continue to execute I/O on them.
Move the per session cmd counters to a new struct so iSCSI can allocate
them per connection. The xcopy code can also just not allocate in the
future since it doesn't need to track commands.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-2-michael.christie@oracle.com
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allocate UNIT ATTENTION "BUS DEVICE RESET OCCURRED" on all LUNs on all
target ports of the device upon reception of TMF LUN RESET.
This change passes libiscsi test SCSI.MultipathIO.Reset.
Link: https://lore.kernel.org/r/20220913163602.20597-1-d.bogdanov@yadro.com
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently TMF commands are removed from de_device.dev_tmf_list at the very
end of se_cmd lifecycle. However, se_lun unlinks from se_cmd upon a command
status (response) being queued in transport layer. This means that LUN and
backend device can be deleted in the meantime and a panic will occur:
target_tmr_work()
cmd->se_tfo->queue_tm_rsp(cmd); // send abort_rsp to a wire
transport_lun_remove_cmd(cmd) // unlink se_cmd from se_lun
- // - // - // -
<<<--- lun remove
<<<--- core backend device remove
- // - // - // -
qlt_handle_abts_completion()
tfo->free_mcmd()
transport_generic_free_cmd()
target_put_sess_cmd()
core_tmr_release_req() {
if (dev) { // backend device, can not be null
spin_lock_irqsave(&dev->se_tmr_lock, flags); //<<<--- CRASH
Call Trace:
NIP [c000000000e1683c] _raw_spin_lock_irqsave+0x2c/0xc0
LR [c00800000e433338] core_tmr_release_req+0x40/0xa0 [target_core_mod]
Call Trace:
(unreliable)
0x0
target_put_sess_cmd+0x2a0/0x370 [target_core_mod]
transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod]
tcm_qla2xxx_complete_mcmd+0x28/0x50 [tcm_qla2xxx]
process_one_work+0x2c4/0x5c0
worker_thread+0x88/0x690
For the iSCSI protocol this is easily reproduced:
- Send some SCSI sommand
- Send Abort of that command over iSCSI
- Remove LUN on target
- Send next iSCSI command to acknowledge the Abort_Response
- Target panics
There is no need to keep the command in tmr_list until response completion,
so move the removal from tmr_list from the response completion to the
response queueing when the LUN is unlinked. Move the removal from state
list too as it is a subject to the same race condition.
Link: https://lore.kernel.org/r/20211018135753.15297-1-d.bogdanov@yadro.com
Fixes: c66ac9db8d ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following bugs:
1. If there are multiple ordered cmds queued and multiple simple cmds
completing, target_restart_delayed_cmds() could be called on different
CPUs and each instance could start a ordered cmd. They could then run in
different orders than they were queued.
2. target_restart_delayed_cmds() and target_handle_task_attr() can race
where:
1. target_handle_task_attr() has passed the simple_cmds == 0 check.
2. transport_complete_task_attr() then decrements simple_cmds to 0.
3. transport_complete_task_attr() runs target_restart_delayed_cmds() and
it does not see any cmds on the delayed_cmd_list.
4. target_handle_task_attr() adds the cmd to the delayed_cmd_list.
The cmd will then end up timing out.
3. If we are sent > 1 ordered cmds and simple_cmds == 0, we can execute
them out of order, because target_handle_task_attr() will hit that
simple_cmds check first and return false for all ordered cmds sent.
4. We run target_restart_delayed_cmds() after every cmd completion, so if
there is more than 1 simple cmd running, we start executing ordered cmds
after that first cmd instead of waiting for all of them to complete.
5. Ordered cmds are not supposed to start until HEAD OF QUEUE and all older
cmds have completed, and not just simple.
6. It's not a bug but it doesn't make sense to take the delayed_cmd_lock
for every cmd completion when ordered cmds are almost never used. Just
replacing that lock with an atomic increases IOPs by up to 10% when
completions are spread over multiple CPUs and there are multiple
sessions/ mqs/thread accessing the same device.
This patch moves the queued delayed handling to a per device work to
serialze the cmd executions for each device and adds a new counter to track
HEAD_OF_QUEUE and SIMPLE cmds. We can then check the new counter to
determine when to run the work on the completion path.
Link: https://lore.kernel.org/r/20210930020422.92578-3-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can race where target_handle_task_attr() has put the cmd on the
delayed_cmd_list. Then target_restart_delayed_cmds() has removed it and set
CMD_T_SENT, but then target_execute_cmd() now clears that bit.
This patch moves the clearing to before we've put the cmd on the list.
Link: https://lore.kernel.org/r/20210930020422.92578-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the log level of the following message to debug:
Unsupported SCSI Opcode 0xXX, sending CHECK_CONDITION.
This message is mostly helpful during debugging sessions in order to
understand errors on the initiator side. But most of the time it's just
useless and makes reading logs much harder.
It gets particularly annoying if there are many initiators that come and go
or if an initiator runs a program that does not care whether the command is
supported and just keeps sending it.
Link: https://lore.kernel.org/r/20210929114959.705852-1-k.shelekhin@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Konstantin Shelekhin <k.shelekhin@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, backend drivers can fail I/O with SAM_STAT_CHECK_CONDITION which
gets us TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE.
Add a new helper that allows backend drivers to fail with specific sense
codes.
This is based on a patch from Mike Christie <michael.christie@oracle.com>.
Cc: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20210803145410.80147-2-s.samoylenko@yadro.com
Reviewed-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Sergey Samoylenko <s.samoylenko@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These members are only used for ALUA sense detail propagation, which can
just as easily be done via sense_reason_t.
Link: https://lore.kernel.org/r/20210728115353.2396-4-ddiss@suse.de
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CPU affinity control added with commit 39ae3edda3 ("scsi: target: core:
Make completion affinity configurable") makes target_complete_cmd() queue
work on a CPU based on se_tpg->se_tpg_wwn->cmd_compl_affinity state.
LIO's EXTENDED COPY worker is a special case in that read/write cmds are
dispatched using the global xcopy_pt_tpg, which carries a NULL se_tpg_wwn
pointer following initialization in target_xcopy_setup_pt().
The NULL xcopy_pt_tpg->se_tpg_wwn pointer is dereferenced on completion of
any EXTENDED COPY initiated read/write cmds. E.g using the libiscsi
SCSI.ExtendedCopy.Simple test:
BUG: kernel NULL pointer dereference, address: 00000000000001a8
RIP: 0010:target_complete_cmd+0x9d/0x130 [target_core_mod]
Call Trace:
fd_execute_rw+0x148/0x42a [target_core_file]
? __dynamic_pr_debug+0xa7/0xe0
? target_check_reservation+0x5b/0x940 [target_core_mod]
__target_execute_cmd+0x1e/0x90 [target_core_mod]
transport_generic_new_cmd+0x17c/0x330 [target_core_mod]
target_xcopy_issue_pt_cmd+0x9/0x60 [target_core_mod]
target_xcopy_read_source.isra.7+0x10b/0x1b0 [target_core_mod]
? target_check_fua+0x40/0x40 [target_core_mod]
? transport_complete_task_attr+0x130/0x130 [target_core_mod]
target_xcopy_do_work+0x61f/0xc00 [target_core_mod]
This fix makes target_complete_cmd() queue work on se_cmd->cpuid if
se_tpg_wwn is NULL.
Link: https://lore.kernel.org/r/20210720225522.26291-1-ddiss@suse.de
Fixes: 39ae3edda3 ("scsi: target: core: Make completion affinity configurable")
Cc: Lee Duncan <lduncan@suse.com>
Cc: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On realtime kernels, spin_lock_irq*(spinlock_t) do not disable the
interrupts, a call to irqs_disabled() will return false thus firing a
warning in __transport_wait_for_tasks().
Remove the warning and also replace assert_spin_locked() with
lockdep_assert_held()
Link: https://lore.kernel.org/r/20210531121326.3649-1-mlombard@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix warning:
drivers/target/target_core_transport.c:1661: WARNING: Block quote ends
without a blank line; unexpected unindent.
Link: https://lore.kernel.org/r/20210318225858.11863-1-michael.christie@oracle.com
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It may not always be best to complete the IO on same CPU as it was
submitted on. This commit allows userspace to configure it.
This has been useful for vhost-scsi where we have a single thread for
submissions and completions. If we force the completion on the submission
CPU we may be adding conflicts with what the user has setup in the lower
levels with settings like the block layer rq_affinity or the driver's IRQ
or softirq (the network's rps_cpus value) settings.
We may also want to set it up where the vhost thread runs on CPU N and does
its submissions/completions there, and then have LIO do its completion
booking on CPU M, but can't configure the lower levels due to issues like
using dm-multipath with lots of paths (the path selector can throw commands
all over the system because it's only taking into account latency/throughput
at its level).
The new setting is in:
/sys/kernel/config/target/$fabric/$target/param/cmd_completion_affinity
Writing:
-1 -> Gives the current default behavior of completing on the
submission CPU.
-2 -> Completes the cmd on the CPU the lower layers sent it to us from.
> 0 -> Completes on the CPU userspace has specified.
Link: https://lore.kernel.org/r/20210227170006.5077-26-michael.christie@oracle.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
target_core_iblock is plugging and unplugging on every command and this is
causing perf issues for drivers that prefer batched cmds. With recent
patches we can now take multiple cmds from a fabric driver queue and then
pass them down the backend drivers in a batch. This patch adds this support
by adding 2 callouts to the backend for plugging and unplugging the
device. Subsequent commits will add support for iblock and tcmu device
plugging.
Link: https://lore.kernel.org/r/20210227170006.5077-22-michael.christie@oracle.com
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
loop and vhost/scsi do their target cmd submission from driver
workqueues. This allows them to avoid an issue where the backend may block
waiting for resources like tags/requests, mem/locks, etc and that ends up
blocking their entire submission path and for the case of vhost-scsi both
the submission and completion path.
This patch adds a helper drivers can use to submit from a LIO workqueue.
This code will then be extended in the next patches to fix the plugging of
backend devices.
We are only converting vhost/loop initially, but the workqueue based
submission will work for other drivers and have similar benefits where the
main target loops will not end up blocking one some backend resource.
Link: https://lore.kernel.org/r/20210227170006.5077-17-michael.christie@oracle.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tcm_loop could be used like a normal block device, so we can't use
GFP_KERNEL and should use GFP_NOIO. This adds a gfp_t arg to
target_cmd_init_cdb() and converts the users. For every driver but loop
GFP_KERNEL is kept.
This will also be useful in subsequent patches where loop needs to do
target_submit_prep() from interrupt context to get a ref to the se_device,
and so it will need to use GFP_ATOMIC.
Link: https://lore.kernel.org/r/20210227170006.5077-16-michael.christie@oracle.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert target_submit_cmd() to do its own calls and then remove
target_submit_cmd_map_sgls() since no one uses it.
Link: https://lore.kernel.org/r/20210227170006.5077-15-michael.christie@oracle.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This breaks up target_submit_cmd_map_sgls() into 3 helpers:
- target_init_cmd(): Do the basic general setup and get a refcount to the
session to make sure the caller can execute the cmd.
- target_submit_prep(): Do the mapping, cdb processing and get a ref to
the LUN.
- target_submit(): Pass the cmd to LIO core for execution.
The above functions must be used by drivers that either:
1. Rely on LIO for session shutdown synchronization by calling
target_stop_session().
2. Need to map sgls.
When the next patches are applied then simple drivers that do not need the
extra functionality above can use target_submit_cmd() and not worry about
failures being returned and how to handle them, since many drivers were
getting this wrong and would have hit refcount bugs.
Also, by breaking target_submit_cmd_map_sgls() up into these 3 helper
functions, we can allow the later patches to do the init/prep from
interrupt context and then do the submission from a workqueue.
Link: https://lore.kernel.org/r/20210227170006.5077-5-michael.christie@oracle.com
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Michael Cyr <mikecyr@linux.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename transport_init_se_cmd() to __target_init_cmd() to reflect that it is
more of an internal function that drivers should normally not use and
because we are going to add a new init function in the next patches.
Link: https://lore.kernel.org/r/20210227170006.5077-4-michael.christie@oracle.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The kref_get_unless_zero() use in target_get_sess_cmd() was added in:
commit 1b4c59b7a1 ("target: fix potential race window in
target_sess_cmd_list_waiting()")'
but it does not seem to do anything.
The original patch might have thought we could have added the cmd to the
sess_wait_list and then target_wait_for_sess_cmds could do a put before
target_get_sess_cmd did its get. That wouldn't happen because we do the get
first then grab the sess lock and put it on the list.
It is also not needed now, because the sess_cmd_list does not exist anymore
and we instead wait on the session cmd_count.
The other problem with the commit is that several
target_submit_cmd_map_sgls()/target_submit_cmd() callers do not handle the
error case properly if it were to ever happen. These drivers think they
have their normal refcount on the cmd and in many cases do a
transport_generic_free_cmd() plus target_put_sess_cmd() so they would have
fired off the refcount WARN/BUGs.
This patch just changes the kref_get_unless_zero() to kref_get().
Link: https://lore.kernel.org/r/20210227170006.5077-3-michael.christie@oracle.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prepare to split target_submit_cmd_map_sgls() so the initialization and
submission part can be called at different times. If the init part fails we
can reference the t_task_cdb early in some of the logging and tracing
code. Move it to transport_init_se_cmd() so we don't hit NULL pointer
crashes.
Link: https://lore.kernel.org/r/20210227170006.5077-2-michael.christie@oracle.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
TCM doesn't properly handle underflow case for service actions. One way to
prevent it is to always complete command with
target_complete_cmd_with_length(), however it requires access to data_sg,
which is not always available.
This change introduces target_set_cmd_data_length() function which allows
to set command data length before completing it.
Link: https://lore.kernel.org/r/20210209072202.41154-2-a.miloserdov@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Aleksandr Miloserdov <a.miloserdov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to FCP-4 (9.4.2):
If the command requested that data beyond the length specified by the
FCP_DL field be transferred, then the device server shall set the
FCP_RESID_OVER bit (see 9.5.8) to one in the FCP_RSP IU and:
a) process the command normally except that data beyond the FCP_DL count
shall not be requested or transferred;
b) transfer no data and return CHECK CONDITION status with the sense key
set to ILLEGAL REQUEST and the additional sense code set to INVALID FIELD
IN COMMAND INFORMATION UNIT; or
c) may transfer data and return CHECK CONDITION status with the sense key
set to ABORTED COMMAND and the additional sense code set to INVALID FIELD
IN COMMAND INFORMATION UNIT.
TCM follows b) and transfers no data for residual writes but returns
INVALID FIELD IN CDB instead of INVALID FIELD IN COMMAND INFORMATION UNIT.
Change the ASCQ to INVALID FIELD IN COMMAND INFORMATION UNIT to meet the
standard.
Link: https://lore.kernel.org/r/20201203082035.54566-4-a.kovaleva@yadro.com
Signed-off-by: Anastasia Kovaleva <a.kovaleva@yadro.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to RFC 7143 11.4.5.2.:
If SPDTL > EDTL for a task, iSCSI Overflow MUST be signaled in the SCSI
Response PDU as specified in Section 11.4.5.1. The Residual Count MUST
be set to the numerical value of (SPDTL - EDTL).
If SPDTL < EDTL for a task, iSCSI Underflow MUST be signaled in the SCSI
Response PDU as specified in Section 11.4.5.1. The Residual Count MUST
be set to the numerical value of (EDTL - SPDTL).
libiscsi has residual write tests that check residual kind and residual
amount and all of them (Write10Residuals, Write12Residuals,
Write16Residuals) currently fail.
One of the reasons why they fail is because target completes write commands
with INVALID FIELD IN CDB before setting the Overflow/Underflow bit and
residual amount.
Set the Overflow/Underflow bit and the residual amount before failing a
write to comply with RFC 7143.
Link: https://lore.kernel.org/r/20201203082035.54566-3-a.kovaleva@yadro.com
Signed-off-by: Anastasia Kovaleva <a.kovaleva@yadro.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
TCM always fails SBC commands with residuals for 4Kn devices when the
command is processed by sbc_parse_cdb(). That prevents residual signalling
to the transport driver because residual kind and residual amount aren't
set. It also makes residual handling different from 512-byte formatted
devices - if there are residuals 512-byte LUN would proceed with command
execution while 4K-byte LUN would fail.
Link: https://lore.kernel.org/r/20201203082035.54566-2-a.kovaleva@yadro.com
Based-on: https://patchwork.kernel.org/project/target-devel/patch/20170523234854.21452-31-bart.vanassche@sandisk.com/
Based-on-patch-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Konstantin Vinogradov <k.vinogradov@yadro.com>
Signed-off-by: Anastasia Kovaleva <a.kovaleva@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
transport_handle_cdb_direct() uses in_interrupt() to detect if it is safe
to sleep. It produces a stack trace and returns with an error which is
clearly for debugging.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
transport_handle_cdb_direct() has a comment saying that it may only be
invoked from process context. It invokes transport_generic_new_cmd() which
performs GFP_KERNEL memory allocations. in_interrupt() does not detect all
the contexts where it is invalid to sleep (for the blocking GFP_KERNEL
allocation) as it fails to detect sections with disabled preemption.
Replace the in_interrupt() based check with a might_sleep() annotation.
Link: https://lore.kernel.org/r/20201220203638.43615-7-bigeasy@linutronix.de
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
target_submit_cmd_map_sgls() uses in_interrupt() to crash if it returns
true.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
The usage of in_interrupt() is clearly for debugging. might_sleep() is
better at this because it also detects other contexts in which it is not
allowed to sleep, like preempt-disabled section.
Replace BUG_ON(in_interrupt) with might_sleep().
Link: https://lore.kernel.org/r/20201220203638.43615-6-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do a state_list/execute_task_lock per CPU, so we can do submissions from
different CPUs without contention with each other.
Note: tcm_fc was passing TARGET_SCF_USE_CPUID, but never set cpuid. The
assumption is that it wanted to set the cpuid to the CPU it was submitting
from so it will get this behavior with this patch.
[mkp: s/printk/pr_err/ + resolve COMPARE AND WRITE patch conflict]
Link: https://lore.kernel.org/r/1604257174-4524-8-git-send-email-michael.christie@oracle.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drop the sess_cmd_lock by:
- Removing the sess_cmd_list use from LIO core, because it's been
moved to qla2xxx.
- Removing sess_tearing_down check in the I/O path. Instead of using that
bit and the sess_cmd_lock, we rely on the cmd_count percpu ref. To do
this we switch to percpu_ref_kill_and_confirm/percpu_ref_tryget_live.
Link: https://lore.kernel.org/r/1604257174-4524-7-git-send-email-michael.christie@oracle.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
percpu_ref_init sets the refcount to 1 and percpu_ref_kill drops it.
Drivers like iSCSI and loop do not call target_sess_cmd_list_set_waiting
during session shutdown, though, so they have been calling percpu_ref_exit
with a refcount still taken and leaking the cmd_counts memory.
Link: https://lore.kernel.org/r/1604257174-4524-3-git-send-email-michael.christie@oracle.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SBC-4 r15 5.3 COMPARE AND WRITE command states:
if the compare operation does not indicate a match, then terminate the
command with CHECK CONDITION status with the sense key set to
MISCOMPARE and the additional sense code set to MISCOMPARE DURING
VERIFY OPERATION. In the sense data (see 4.18 and SPC-5) the offset
from the start of the Data-Out Buffer to the first byte of data that
was not equal shall be reported in the INFORMATION field.
This change implements the missing logic to report the miscompare offset in
the sense data INFORMATION field. As an optimization, byte-by-byte
miscompare offset calculation is only performed after memcmp() mismatch.
Link: https://lore.kernel.org/r/20201031233211.5207-5-ddiss@suse.de
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd.bad_sector currently gets packed into the sense INFORMATION field for
TCM_LOGICAL_BLOCK_{GUARD,APP_TAG,REF_TAG}_CHECK_FAILED errors, which carry
an .add_sector_info flag in the sense_detail_table to ensure this.
In preparation for propagating a byte offset on COMPARE AND WRITE
TCM_MISCOMPARE_VERIFY error, rename cmd.bad_sector to cmd.sense_info and
sense_detail.add_sector_info to sense_detail.add_sense_info so that it
better reflects the sense INFORMATION field destination.
[ddiss: update previously overlooked ib_isert]
Link: https://lore.kernel.org/r/20201031233211.5207-3-ddiss@suse.de
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This helps distinguish it from the SCSI sense INFORMATION field.
Link: https://lore.kernel.org/r/20201031233211.5207-2-ddiss@suse.de
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Two patches in driver frameworks. The iscsi one corrects a bug
induced by a BPF change to network locking and the other is a
regression we introduced.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX3d3QyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWv9AP9lxJ1U
32sHZ5d46Idsd8ipfYmEqCh8s/9cTvx9VEwmdQEAzeH3nvAEJXX4YEzmnsKeF6Nf
IFLoRQ7RLEhfmNfJ/L0=
=96lr
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two patches in driver frameworks. The iscsi one corrects a bug induced
by a BPF change to network locking and the other is a regression we
introduced"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: iscsi_tcp: Avoid holding spinlock while calling getpeername()
scsi: target: Fix lun lookup for TARGET_SCF_LOOKUP_LUN_FROM_TAG case
