Most of the original conversion is from the spatch below,
but I edited some and left out other instances that were
either buggy after conversion (where default values don't
fit into the type) or just looked strange.
@@
expression attr, def;
expression val;
identifier fn =~ "^nla_get_.*";
fresh identifier dfn = fn ## "_default";
@@
(
-if (attr)
- val = fn(attr);
-else
- val = def;
+val = dfn(attr, def);
|
-if (!attr)
- val = def;
-else
- val = fn(attr);
+val = dfn(attr, def);
|
-if (!attr)
- return def;
-return fn(attr);
+return dfn(attr, def);
|
-attr ? fn(attr) : def
+dfn(attr, def)
|
-!attr ? def : fn(attr)
+dfn(attr, def)
)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@kernel.org>
Link: https://patch.msgid.link/20241108114145.0580b8684e7f.I740beeaa2f70ebfc19bfca1045a24d6151992790@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clearing the secpath for internal ports will cause packet drops when
ipsec offload or early SW ipsec decrypt are used. Systems that rely
on these will not be able to actually pass traffic via openvswitch.
There is still an open issue for a flow miss packet - this is because
we drop the extensions during upcall and there is no facility to
restore such data (and it is non-trivial to add such functionality
to the upcall interface). That means that when a flow miss occurs,
there will still be packet drops. With this patch, when a flow is
found then traffic which has an associated xfrm extension will
properly flow.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://patch.msgid.link/20241101204732.183840-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"Interface can't change network namespaces" is rather an attribute,
not a feature, and it can't be changed via Ethtool.
Make it a "cold" private flag instead of a netdev_feature and free
one more bit.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NETIF_F_LLTX can't be changed via Ethtool and is not a feature,
rather an attribute, very similar to IFF_NO_QUEUE (and hot).
Free one netdev_features_t bit and make it a "hot" private flag.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Using ERR_CAST() is more reasonable and safer, When it is necessary
to convert the type of an error pointer and return it.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240829095509.3151987-1-yanzhen@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
<tldr>
skb network header of the single-tagged vlan packet continues to point the
vlan payload (e.g. IP) after second vlan tag is pushed by tc act_vlan. This
causes problem at the dissector which expects double-tagged packet network
header to point to the inner vlan.
The fix is to adjust network header in tcf_act_vlan.c but requires
refactoring of skb_vlan_push function.
</tldr>
Consider the following shell script snippet configuring TC rules on the
veth interface:
ip link add veth0 type veth peer veth1
ip link set veth0 up
ip link set veth1 up
tc qdisc add dev veth0 clsact
tc filter add dev veth0 ingress pref 10 chain 0 flower \
num_of_vlans 2 cvlan_ethtype 0x800 action goto chain 5
tc filter add dev veth0 ingress pref 20 chain 0 flower \
num_of_vlans 1 action vlan push id 100 \
protocol 0x8100 action goto chain 5
tc filter add dev veth0 ingress pref 30 chain 5 flower \
num_of_vlans 2 cvlan_ethtype 0x800 action simple sdata "success"
Sending double-tagged vlan packet with the IP payload inside:
cat <<ENDS | text2pcap - - | tcpreplay -i veth1 -
0000 00 00 00 00 00 11 00 00 00 00 00 22 81 00 00 64 ..........."...d
0010 81 00 00 14 08 00 45 04 00 26 04 d2 00 00 7f 11 ......E..&......
0020 18 ef 0a 00 00 01 14 00 00 02 00 00 00 00 00 12 ................
0030 e1 c7 00 00 00 00 00 00 00 00 00 00 ............
ENDS
will match rule 10, goto rule 30 in chain 5 and correctly emit "success" to
the dmesg.
OTOH, sending single-tagged vlan packet:
cat <<ENDS | text2pcap - - | tcpreplay -i veth1 -
0000 00 00 00 00 00 11 00 00 00 00 00 22 81 00 00 14 ..........."....
0010 08 00 45 04 00 2a 04 d2 00 00 7f 11 18 eb 0a 00 ..E..*..........
0020 00 01 14 00 00 02 00 00 00 00 00 16 e1 bf 00 00 ................
0030 00 00 00 00 00 00 00 00 00 00 00 00 ............
ENDS
will match rule 20, will push the second vlan tag but will *not* match
rule 30. IOW, the match at rule 30 fails if the second vlan was freshly
pushed by the kernel.
Lets look at __skb_flow_dissect working on the double-tagged vlan packet.
Here is the relevant code from around net/core/flow_dissector.c:1277
copy-pasted here for convenience:
if (dissector_vlan == FLOW_DISSECTOR_KEY_MAX &&
skb && skb_vlan_tag_present(skb)) {
proto = skb->protocol;
} else {
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
data, hlen, &_vlan);
if (!vlan) {
fdret = FLOW_DISSECT_RET_OUT_BAD;
break;
}
proto = vlan->h_vlan_encapsulated_proto;
nhoff += sizeof(*vlan);
}
The "else" clause above gets the protocol of the encapsulated packet from
the skb data at the network header location. printk debugging has showed
that in the good double-tagged packet case proto is
htons(0x800 == ETH_P_IP) as expected. However in the single-tagged packet
case proto is garbage leading to the failure to match tc filter 30.
proto is being set from the skb header pointed by nhoff parameter which is
defined at the beginning of __skb_flow_dissect
(net/core/flow_dissector.c:1055 in the current version):
nhoff = skb_network_offset(skb);
Therefore the culprit seems to be that the skb network offset is different
between double-tagged packet received from the interface and single-tagged
packet having its vlan tag pushed by TC.
Lets look at the interesting points of the lifetime of the single/double
tagged packets as they traverse our packet flow.
Both of them will start at __netif_receive_skb_core where the first vlan
tag will be stripped:
if (eth_type_vlan(skb->protocol)) {
skb = skb_vlan_untag(skb);
if (unlikely(!skb))
goto out;
}
At this stage in double-tagged case skb->data points to the second vlan tag
while in single-tagged case skb->data points to the network (eg. IP)
header.
Looking at TC vlan push action (net/sched/act_vlan.c) we have the following
code at tcf_vlan_act (interesting points are in square brackets):
if (skb_at_tc_ingress(skb))
[1] skb_push_rcsum(skb, skb->mac_len);
....
case TCA_VLAN_ACT_PUSH:
err = skb_vlan_push(skb, p->tcfv_push_proto, p->tcfv_push_vid |
(p->tcfv_push_prio << VLAN_PRIO_SHIFT),
0);
if (err)
goto drop;
break;
....
out:
if (skb_at_tc_ingress(skb))
[3] skb_pull_rcsum(skb, skb->mac_len);
And skb_vlan_push (net/core/skbuff.c:6204) function does:
err = __vlan_insert_tag(skb, skb->vlan_proto,
skb_vlan_tag_get(skb));
if (err)
return err;
skb->protocol = skb->vlan_proto;
[2] skb->mac_len += VLAN_HLEN;
in the case of pushing the second tag. Lets look at what happens with
skb->data of the single-tagged packet at each of the above points:
1. As a result of the skb_push_rcsum, skb->data is moved back to the start
of the packet.
2. First VLAN tag is moved from the skb into packet buffer, skb->mac_len is
incremented, skb->data still points to the start of the packet.
3. As a result of the skb_pull_rcsum, skb->data is moved forward by the
modified skb->mac_len, thus pointing to the network header again.
Then __skb_flow_dissect will get confused by having double-tagged vlan
packet with the skb->data at the network header.
The solution for the bug is to preserve "skb->data at second vlan header"
semantics in the skb_vlan_push function. We do this by manipulating
skb->network_header rather than skb->mac_len. skb_vlan_push callers are
updated to do skb_reset_mac_len.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=O8tu
-----END PGP SIGNATURE-----
Merge tag 'nf-next-24-08-23' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains Netfilter updates for net-next:
Patch #1 fix checksum calculation in nfnetlink_queue with SCTP,
segment GSO packet since skb_zerocopy() does not support
GSO_BY_FRAGS, from Antonio Ojea.
Patch #2 extend nfnetlink_queue coverage to handle SCTP packets,
from Antonio Ojea.
Patch #3 uses consume_skb() instead of kfree_skb() in nfnetlink,
from Donald Hunter.
Patch #4 adds a dedicate commit list for sets to speed up
intra-transaction lookups, from Florian Westphal.
Patch #5 skips removal of element from abort path for the pipapo
backend, ditching the shadow copy of this datastructure
is sufficient.
Patch #6 moves nf_ct_netns_get() out of nf_conncount_init() to
let users of conncoiunt decide when to enable conntrack,
this is needed by openvswitch, from Xin Long.
Patch #7 pass context to all nft_parse_register_load() in
preparation for the next patch.
Patches #8 and #9 reject loads from uninitialized registers from
control plane to remove register initialization from
datapath. From Florian Westphal.
* tag 'nf-next-24-08-23' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_tables: don't initialize registers in nft_do_chain()
netfilter: nf_tables: allow loads only when register is initialized
netfilter: nf_tables: pass context structure to nft_parse_register_load
netfilter: move nf_ct_netns_get out of nf_conncount_init
netfilter: nf_tables: do not remove elements if set backend implements .abort
netfilter: nf_tables: store new sets in dedicated list
netfilter: nfnetlink: convert kfree_skb to consume_skb
selftests: netfilter: nft_queue.sh: sctp coverage
netfilter: nfnetlink_queue: unbreak SCTP traffic
====================
Link: https://patch.msgid.link/20240822221939.157858-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.h
c948c0973d ("bnxt_en: Don't clear ntuple filters and rss contexts during ethtool ops")
f2878cdeb7 ("bnxt_en: Add support to call FW to update a VNIC")
Link: https://patch.msgid.link/20240822210125.1542769-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is something wrong with ovs_drop_reasons. ovs_drop_reasons[0] is
"OVS_DROP_LAST_ACTION", but OVS_DROP_LAST_ACTION == __OVS_DROP_REASON + 1,
which means that ovs_drop_reasons[1] should be "OVS_DROP_LAST_ACTION".
And as Adrian tested, without the patch, adding flow to drop packets
results in:
drop at: do_execute_actions+0x197/0xb20 [openvsw (0xffffffffc0db6f97)
origin: software
input port ifindex: 8
timestamp: Tue Aug 20 10:19:17 2024 859853461 nsec
protocol: 0x800
length: 98
original length: 98
drop reason: OVS_DROP_ACTION_ERROR
With the patch, the same results in:
drop at: do_execute_actions+0x197/0xb20 [openvsw (0xffffffffc0db6f97)
origin: software
input port ifindex: 8
timestamp: Tue Aug 20 10:16:13 2024 475856608 nsec
protocol: 0x800
length: 98
original length: 98
drop reason: OVS_DROP_LAST_ACTION
Fix this by initializing ovs_drop_reasons with index.
Fixes: 9d802da40b ("net: openvswitch: add last-action drop reason")
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Tested-by: Adrian Moreno <amorenoz@redhat.com>
Reviewed-by: Adrian Moreno <amorenoz@redhat.com>
Link: https://patch.msgid.link/20240821123252.186305-1-dongml2@chinatelecom.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to move nf_ct_netns_get() out of nf_conncount_init()
and let the consumers of nf_conncount decide if they want to turn
on netfilter conntrack.
It makes nf_conncount more flexible to be used in other places and
avoids netfilter conntrack turned on when using it in openvswitch
conntrack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Similar to commit 70f06c115b ("sched: act_ct: switch to per-action
label counting"), we should also switch to per-action label counting
in openvswitch conntrack, as Florian suggested.
The difference is that nf_connlabels_get() is called unconditionally
when creating an ct action in ovs_ct_copy_action(). As with these
flows:
table=0,ip,actions=ct(commit,table=1)
table=1,ip,actions=ct(commit,exec(set_field:0xac->ct_label),table=2)
it needs to make sure the label ext is created in the 1st flow before
the ct is committed in ovs_ct_commit(). Otherwise, the warning in
nf_ct_ext_add() when creating the label ext in the 2nd flow will
be triggered:
WARN_ON(nf_ct_is_confirmed(ct));
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/6b9347d5c1a0b364e88d900b29a616c3f8e5b1ca.1723483073.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a packet sample is observed, the sampling rate that was used is
important to estimate the real frequency of such event.
Store the probability of the parent sample action in the skb's cb area
and use it in psample action to pass it down to psample module.
Reviewed-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Link: https://patch.msgid.link/20240704085710.353845-7-amorenoz@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for a new action: psample.
This action accepts a u32 group id and a variable-length cookie and uses
the psample multicast group to make the packet available for
observability.
The maximum length of the user-defined cookie is set to 16, same as
tc_cookie, to discourage using cookies that will not be offloadable.
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Link: https://patch.msgid.link/20240704085710.353845-6-amorenoz@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At this time, conntrack either returns NF_ACCEPT or NF_DROP.
To improve debuging it would be nice to be able to replace NF_DROP
verdict with NF_DROP_REASON() helper,
This helper releases the skb instantly (so drop_monitor can pinpoint
precise location) and returns NF_STOLEN.
Prepare call sites to deal with this before introducing such changes
in conntrack and nat core.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Aaron Conole <aconole@redhat.om>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ilya found a failure in running check-kernel tests with at_groups=144
(144: conntrack - FTP SNAT orig tuple) in OVS repo. After his further
investigation, the root cause is that the labels sent to userspace
for related ct are incorrect.
The labels for unconfirmed related ct should use its master's labels.
However, the changes made in commit 8c8b733208 ("openvswitch: set
IPS_CONFIRMED in tmpl status only when commit is set in conntrack")
led to getting labels from this related ct.
So fix it in ovs_ct_get_labels() by changing to copy labels from its
master ct if it is a unconfirmed related ct. Note that there is no
fix needed for ct->mark, as it was already copied from its master
ct for related ct in init_conntrack().
Fixes: 8c8b733208 ("openvswitch: set IPS_CONFIRMED in tmpl status only when commit is set in conntrack")
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Tested-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20240531111552.3209198-2-leitao@debian.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core instead
of this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Move openvswitch driver to leverage the core allocation.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240531111552.3209198-1-leitao@debian.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
regression you have been notified of in the past weeks.
The TCP window fix will require some follow-up, already queued.
Current release - regressions:
- af_unix: fix garbage collection of embryos
Previous releases - regressions:
- af_unix: fix race between GC and receive path
- ipv6: sr: fix missing sk_buff release in seg6_input_core
- tcp: remove 64 KByte limit for initial tp->rcv_wnd value
- eth: r8169: fix rx hangup
- eth: lan966x: remove ptp traps in case the ptp is not enabled.
- eth: ixgbe: fix link breakage vs cisco switches.
- eth: ice: prevent ethtool from corrupting the channels.
Previous releases - always broken:
- openvswitch: set the skbuff pkt_type for proper pmtud support.
- tcp: Fix shift-out-of-bounds in dctcp_update_alpha().
Misc:
- a bunch of selftests stabilization patches.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=zd2T
-----END PGP SIGNATURE-----
Merge tag 'net-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Quite smaller than usual. Notably it includes the fix for the unix
regression from the past weeks. The TCP window fix will require some
follow-up, already queued.
Current release - regressions:
- af_unix: fix garbage collection of embryos
Previous releases - regressions:
- af_unix: fix race between GC and receive path
- ipv6: sr: fix missing sk_buff release in seg6_input_core
- tcp: remove 64 KByte limit for initial tp->rcv_wnd value
- eth: r8169: fix rx hangup
- eth: lan966x: remove ptp traps in case the ptp is not enabled
- eth: ixgbe: fix link breakage vs cisco switches
- eth: ice: prevent ethtool from corrupting the channels
Previous releases - always broken:
- openvswitch: set the skbuff pkt_type for proper pmtud support
- tcp: Fix shift-out-of-bounds in dctcp_update_alpha()
Misc:
- a bunch of selftests stabilization patches"
* tag 'net-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (25 commits)
r8169: Fix possible ring buffer corruption on fragmented Tx packets.
idpf: Interpret .set_channels() input differently
ice: Interpret .set_channels() input differently
nfc: nci: Fix handling of zero-length payload packets in nci_rx_work()
net: relax socket state check at accept time.
tcp: remove 64 KByte limit for initial tp->rcv_wnd value
net: ti: icssg_prueth: Fix NULL pointer dereference in prueth_probe()
tls: fix missing memory barrier in tls_init
net: fec: avoid lock evasion when reading pps_enable
Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"
testing: net-drv: use stats64 for testing
net: mana: Fix the extra HZ in mana_hwc_send_request
net: lan966x: Remove ptp traps in case the ptp is not enabled.
openvswitch: Set the skbuff pkt_type for proper pmtud support.
selftest: af_unix: Make SCM_RIGHTS into OOB data.
af_unix: Fix garbage collection of embryos carrying OOB with SCM_RIGHTS
tcp: Fix shift-out-of-bounds in dctcp_update_alpha().
selftests/net: use tc rule to filter the na packet
ipv6: sr: fix memleak in seg6_hmac_init_algo
af_unix: Update unix_sk(sk)->oob_skb under sk_receive_queue lock.
...
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Open vSwitch is originally intended to switch at layer 2, only dealing with
Ethernet frames. With the introduction of l3 tunnels support, it crossed
into the realm of needing to care a bit about some routing details when
making forwarding decisions. If an oversized packet would need to be
fragmented during this forwarding decision, there is a chance for pmtu
to get involved and generate a routing exception. This is gated by the
skbuff->pkt_type field.
When a flow is already loaded into the openvswitch module this field is
set up and transitioned properly as a packet moves from one port to
another. In the case that a packet execute is invoked after a flow is
newly installed this field is not properly initialized. This causes the
pmtud mechanism to omit sending the required exception messages across
the tunnel boundary and a second attempt needs to be made to make sure
that the routing exception is properly setup. To fix this, we set the
outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get
to the openvswitch module via a port device or packet command.
Even for bridge ports as users, the pkt_type needs to be reset when
doing the transmit as the packet is truly outgoing and routing needs
to get involved post packet transformations, in the case of
VXLAN/GENEVE/udp-tunnel packets. In general, the pkt_type on output
gets ignored, since we go straight to the driver, but in the case of
tunnel ports they go through IP routing layer.
This issue is periodically encountered in complex setups, such as large
openshift deployments, where multiple sets of tunnel traversal occurs.
A way to recreate this is with the ovn-heater project that can setup
a networking environment which mimics such large deployments. We need
larger environments for this because we need to ensure that flow
misses occur. In these environment, without this patch, we can see:
./ovn_cluster.sh start
podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200
podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142)
--- 21.0.0.3 ping statistics ---
...
Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not
sent into the server.
With this patch, setting the pkt_type, we see the following:
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222)
ping: local error: message too long, mtu=1222
--- 21.0.0.3 ping statistics ---
...
In this case, the first ping request receives the FRAG_NEEDED message and
a local routing exception is created.
Tested-by: Jaime Caamano <jcaamano@redhat.com>
Reported-at: https://issues.redhat.com/browse/FDP-164
Fixes: 58264848a5 ("openvswitch: Add vxlan tunneling support.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240516200941.16152-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
OVS_PACKET_CMD_EXECUTE has 3 main attributes:
- OVS_PACKET_ATTR_KEY - Packet metadata in a netlink format.
- OVS_PACKET_ATTR_PACKET - Binary packet content.
- OVS_PACKET_ATTR_ACTIONS - Actions to execute on the packet.
OVS_PACKET_ATTR_KEY is parsed first to populate sw_flow_key structure
with the metadata like conntrack state, input port, recirculation id,
etc. Then the packet itself gets parsed to populate the rest of the
keys from the packet headers.
Whenever the packet parsing code starts parsing the ICMPv6 header, it
first zeroes out fields in the key corresponding to Neighbor Discovery
information even if it is not an ND packet.
It is an 'ipv6.nd' field. However, the 'ipv6' is a union that shares
the space between 'nd' and 'ct_orig' that holds the original tuple
conntrack metadata parsed from the OVS_PACKET_ATTR_KEY.
ND packets should not normally have conntrack state, so it's fine to
share the space, but normal ICMPv6 Echo packets or maybe other types of
ICMPv6 can have the state attached and it should not be overwritten.
The issue results in all but the last 4 bytes of the destination
address being wiped from the original conntrack tuple leading to
incorrect packet matching and potentially executing wrong actions
in case this packet recirculates within the datapath or goes back
to userspace.
ND fields should not be accessed in non-ND packets, so not clearing
them should be fine. Executing memset() only for actual ND packets to
avoid the issue.
Initializing the whole thing before parsing is needed because ND packet
may not contain all the options.
The issue only affects the OVS_PACKET_CMD_EXECUTE path and doesn't
affect packets entering OVS datapath from network interfaces, because
in this case CT metadata is populated from skb after the packet is
already parsed.
Fixes: 9dd7f8907c ("openvswitch: Add original direction conntrack tuple to sw_flow_key.")
Reported-by: Antonin Bas <antonin.bas@broadcom.com>
Closes: https://github.com/openvswitch/ovs-issues/issues/327
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240509094228.1035477-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal
of ovs_ct_limit_exit, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 11efd5cb04 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_get_by_name will provide a reference on the netdev. So ensure that
the reference of netdev is released after completed.
Fixes: 2540088b83 ("net: openvswitch: Check vport netdev name")
Signed-off-by: Jun Gu <jun.gu@easystack.cn>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20240423073751.52706-1-jun.gu@easystack.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure that the provided netdev name is not one of its aliases to
prevent unnecessary creation and destruction of the vport by
ovs-vswitchd.
Signed-off-by: Jun Gu <jun.gu@easystack.cn>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240419061425.132723-1-jun.gu@easystack.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On startup, ovs-vswitchd probes different datapath features including
support for timeout policies. While probing, it tries to execute
certain operations with OVS_PACKET_ATTR_PROBE or OVS_FLOW_ATTR_PROBE
attributes set. These attributes tell the openvswitch module to not
log any errors when they occur as it is expected that some of the
probes will fail.
For some reason, setting the timeout policy ignores the PROBE attribute
and logs a failure anyway. This is causing the following kernel log
on each re-start of ovs-vswitchd:
kernel: Failed to associated timeout policy `ovs_test_tp'
Fix that by using the same logging macro that all other messages are
using. The message will still be printed at info level when needed
and will be rate limited, but with a net rate limiter instead of
generic printk one.
The nf_ct_set_timeout() itself will still print some info messages,
but at least this change makes logging in openvswitch module more
consistent.
Fixes: 06bd2bdf19 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240403203803.2137962-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genetlink.h is a shell of what used to be a combined uAPI
and kernel header over a decade ago. It has fewer than
10 lines of code. Merge it into net/genetlink.h.
In some ways it'd be better to keep the combined header
under linux/ but it would make looking through git history
harder.
Acked-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20240329175710.291749-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only legit reason I could think of for net/genetlink.h
and linux/genetlink.h to be separate would be if one was
included by other headers and we wanted to keep it lightweight.
That is not the case, net/openvswitch/meter.h includes
linux/genetlink.h but for no apparent reason (for struct genl_family
perhaps? it's not necessary, types of externs do not need
to be known).
Link: https://lore.kernel.org/r/20240329175710.291749-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Historically, tunnel flags like TUNNEL_CSUM or TUNNEL_ERSPAN_OPT
have been defined as __be16. Now all of those 16 bits are occupied
and there's no more free space for new flags.
It can't be simply switched to a bigger container with no
adjustments to the values, since it's an explicit Endian storage,
and on LE systems (__be16)0x0001 equals to
(__be64)0x0001000000000000.
We could probably define new 64-bit flags depending on the
Endianness, i.e. (__be64)0x0001 on BE and (__be64)0x00010000... on
LE, but that would introduce an Endianness dependency and spawn a
ton of Sparse warnings. To mitigate them, all of those places which
were adjusted with this change would be touched anyway, so why not
define stuff properly if there's no choice.
Define IP_TUNNEL_*_BIT counterparts as a bit number instead of the
value already coded and a fistful of <16 <-> bitmap> converters and
helpers. The two flags which have a different bit position are
SIT_ISATAP_BIT and VTI_ISVTI_BIT, as they were defined not as
__cpu_to_be16(), but as (__force __be16), i.e. had different
positions on LE and BE. Now they both have strongly defined places.
Change all __be16 fields which were used to store those flags, to
IP_TUNNEL_DECLARE_FLAGS() -> DECLARE_BITMAP(__IP_TUNNEL_FLAG_NUM) ->
unsigned long[1] for now, and replace all TUNNEL_* occurrences to
their bitmap counterparts. Use the converters in the places which talk
to the userspace, hardware (NFP) or other hosts (GRE header). The rest
must explicitly use the new flags only. This must be done at once,
otherwise there will be too many conversions throughout the code in
the intermediate commits.
Finally, disable the old __be16 flags for use in the kernel code
(except for the two 'irregular' flags mentioned above), to prevent
any accidental (mis)use of them. For the userspace, nothing is
changed, only additions were made.
Most noticeable bloat-o-meter difference (.text):
vmlinux: 307/-1 (306)
gre.ko: 62/0 (62)
ip_gre.ko: 941/-217 (724) [*]
ip_tunnel.ko: 390/-900 (-510) [**]
ip_vti.ko: 138/0 (138)
ip6_gre.ko: 534/-18 (516) [*]
ip6_tunnel.ko: 118/-10 (108)
[*] gre_flags_to_tnl_flags() grew, but still is inlined
[**] ip_tunnel_find() got uninlined, hence such decrease
The average code size increase in non-extreme case is 100-200 bytes
per module, mostly due to sizeof(long) > sizeof(__be16), as
%__IP_TUNNEL_FLAG_NUM is less than %BITS_PER_LONG and the compilers
are able to expand the majority of bitmap_*() calls here into direct
operations on scalars.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ovs module allows for some actions to recursively contain an action
list for complex scenarios, such as sampling, checking lengths, etc.
When these actions are copied into the internal flow table, they are
evaluated to validate that such actions make sense, and these calls
happen recursively.
The ovs-vswitchd userspace won't emit more than 16 recursion levels
deep. However, the module has no such limit and will happily accept
limits larger than 16 levels nested. Prevent this by tracking the
number of recursions happening and manually limiting it to 16 levels
nested.
The initial implementation of the sample action would track this depth
and prevent more than 3 levels of recursion, but this was removed to
support the clone use case, rather than limited at the current userspace
limit.
Fixes: 798c166173 ("openvswitch: Optimize sample action for the clone use cases")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240207132416.1488485-2-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Referenced commit doesn't always set iifidx when offloading the flow to
hardware. Fix the following cases:
- nf_conn_act_ct_ext_fill() is called before extension is created with
nf_conn_act_ct_ext_add() in tcf_ct_act(). This can cause rule offload with
unspecified iifidx when connection is offloaded after only single
original-direction packet has been processed by tc data path. Always fill
the new nf_conn_act_ct_ext instance after creating it in
nf_conn_act_ct_ext_add().
- Offloading of unidirectional UDP NEW connections is now supported, but ct
flow iifidx field is not updated when connection is promoted to
bidirectional which can result reply-direction iifidx to be zero when
refreshing the connection. Fill in the extension and update flow iifidx
before calling flow_offload_refresh().
Fixes: 9795ded7f9 ("net/sched: act_ct: Fill offloading tuple iifidx")
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 6a9bad0069 ("net/sched: act_ct: offload UDP NEW connections")
Link: https://lore.kernel.org/r/20231103151410.764271-1-vladbu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ca5c8049f58bb933f231afd0816e30a5aaa0eddd.1697264974.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct dp_meter.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: dev@openvswitch.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922172858.3822653-12-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct dp_meter_instance.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: dev@openvswitch.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922172858.3822653-10-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
do_execute_actions() function can be called recursively multiple
times while executing actions that require pipeline forking or
recirculations. It may also be re-entered multiple times if the packet
leaves openvswitch module and re-enters it through a different port.
Currently, there is a 256-byte array allocated on stack in this
function that is supposed to hold NSH header. Compilers tend to
pre-allocate that space right at the beginning of the function:
a88: 48 81 ec b0 01 00 00 sub $0x1b0,%rsp
NSH is not a very common protocol, but the space is allocated on every
recursive call or re-entry multiplying the wasted stack space.
Move the stack allocation to push_nsh() function that is only used
if NSH actions are actually present. push_nsh() is also a simple
function without a possibility for re-entry, so the stack is returned
right away.
With this change the preallocated space is reduced by 256 B per call:
b18: 48 81 ec b0 00 00 00 sub $0xb0,%rsp
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eelco Chaudron echaudro@redhat.com
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1202cdd66531("Remove DECnet support from kernel") has been
merged, all callers pass in the initial_ref value of 1 when they call
dst_alloc(). Therefore, remove initial_ref when the dst_alloc() is
declared and replace initial_ref with 1 in dst_alloc().
Also when all callers call dst_init(), the value of initial_ref is 1.
Therefore, remove the input parameter initial_ref of the dst_init() and
replace initial_ref with the value 1 in dst_init.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20230911125045.346390-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/sfc/tc.c
fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
3bf969e88a ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recent changes in net-next (commit 759ab1edb5 ("net: store netdevs
in an xarray")) refactored the handling of pre-assigned ifindexes
and let syzbot surface a latent problem in ovs. ovs does not validate
ifindex, making it possible to create netdev ports with negative
ifindex values. It's easy to repro with YNL:
$ ./cli.py --spec netlink/specs/ovs_datapath.yaml \
--do new \
--json '{"upcall-pid": 1, "name":"my-dp"}'
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
$ ip link show
-65536: some-port0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 7a:48:21:ad:0b:fb brd ff:ff:ff:ff:ff:ff
...
Validate the inputs. Now the second command correctly returns:
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
lib.ynl.NlError: Netlink error: Numerical result out of range
nl_len = 108 (92) nl_flags = 0x300 nl_type = 2
error: -34 extack: {'msg': 'integer out of range', 'unknown': [[type:4 len:36] b'\x0c\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x0c\x00\x03\x00\xff\xff\xff\x7f\x00\x00\x00\x00\x08\x00\x01\x00\x08\x00\x00\x00'], 'bad-attr': '.ifindex'}
Accept 0 since it used to be silently ignored.
Fixes: 54c4ef34c4 ("openvswitch: allow specifying ifindex of new interfaces")
Reported-by: syzbot+7456b5dcf65111553320@syzkaller.appspotmail.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20230814203840.2908710-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only three families use info->userhdr today and going forward
we discourage using fixed headers in new families.
So having the pointer to user header in struct genl_info
is an overkill. Compute the header pointer at runtime.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20230814214723.2924989-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use drop reasons from include/net/dropreason-core.h when a reasonable
candidate exists.
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using an independent drop reason it makes it easy to distinguish
between QoS-triggered or flow-triggered drop.
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Eric Garver <eric@garver.life>
This adds an explicit drop action. This is used by OVS to drop packets
for which it cannot determine what to do. An explicit action in the
kernel allows passing the reason _why_ the packet is being dropped or
zero to indicate no particular error happened (i.e: OVS intentionally
dropped the packet).
Since the error codes coming from userspace mean nothing for the kernel,
we squash all of them into only two drop reasons:
- OVS_DROP_EXPLICIT_WITH_ERROR to indicate a non-zero value was passed
- OVS_DROP_EXPLICIT to indicate a zero value was passed (no error)
e.g. trace all OVS dropped skbs
# perf trace -e skb:kfree_skb --filter="reason >= 0x30000"
[..]
106.023 ping/2465 skb:kfree_skb(skbaddr: 0xffffa0e8765f2000, \
location:0xffffffffc0d9b462, protocol: 2048, reason: 196611)
reason: 196611 --> 0x30003 (OVS_DROP_EXPLICIT)
Also, this patch allows ovs-dpctl.py to add explicit drop actions as:
"drop" -> implicit empty-action drop
"drop(0)" -> explicit non-error action drop
"drop(42)" -> explicit error action drop
Signed-off-by: Eric Garver <eric@garver.life>
Co-developed-by: Adrian Moreno <amorenoz@redhat.com>
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a drop reason for packets that are dropped because an action
returns a non-zero error code.
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new drop reason subsystem for openvswitch and add the first
drop reason to represent last-action drops.
Last-action drops happen when a flow has an empty action list or there
is no action that consumes the packet (output, userspace, recirc, etc).
It is the most common way in which OVS drops packets.
Implementation-wise, most of these skb-consuming actions already call
"consume_skb" internally and return directly from within the
do_execute_actions() loop so with minimal changes we can assume that
any skb that exits the loop normally is a packet drop.
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By not setting IPS_CONFIRMED in tmpl that allows the exp not to be removed
from the hashtable when lookup, we can simplify the exp processing code a
lot in openvswitch conntrack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since its introduction, the ovs module execute_hash action allowed
hash algorithms other than the skb->l4_hash to be used. However,
additional hash algorithms were not implemented. This means flows
requiring different hash distributions weren't able to use the
kernel datapath.
Now, introduce support for symmetric hashing algorithm as an
alternative hash supported by the ovs module using the flow
dissector.
Output of flow using l4_sym hash:
recirc_id(0),in_port(3),eth(),eth_type(0x0800),
ipv4(dst=64.0.0.0/192.0.0.0,proto=6,frag=no), packets:30473425,
bytes:45902883702, used:0.000s, flags:SP.,
actions:hash(sym_l4(0)),recirc(0xd)
Some performance testing with no GRO/GSO, two veths, single flow:
hash(l4(0)): 4.35 GBits/s
hash(l4_sym(0)): 4.24 GBits/s
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
