The RPC and RPCD2 core clocks were added to the sections for internal
core clocks, while they are core clock outputs, visible from DT.
Move them to the correct sections.
Rename the ".rpc" clock on R-Car S4 to "rpc".
Fixup nearby whitespace to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a938b938f00939b9206d7fbaba78e2ef09915f5f.1649681891.git.geert+renesas@glider.be
Ensures RWDT remains alert throughout the boot process if enabled.
This patch applies the change to the following SoCs: r8a77950, r8a77951,
r8a77960, r8a77961, r8a77965, r8a77970, r8a77980, r8a77990 and r8a77995.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200616162626.27944-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from
it, as well as the RPC-IF module clock, in the R-Car M3-W/M3-W+
(R8A7796) CPG/MSSR driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Link: https://lore.kernel.org/r/20200203072901.31548-2-dirk.behme@de.bosch.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the CryptoCell module clocks and their parents for the CryptoCell
instances in the various Renesas R-Car Gen3 SoCs that do not have
support for them yet in their clock drivers (M3-W/W+, M3-N, E3, D3).
The R-Car H3 clock driver already supports these clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200124133137.15921-1-geert+renesas@glider.be
Add support for the R-Car M3-W+ (R8A77961) SoC to the Renesas Clock
Pulse Generator / Module Standby and Software Reset driver.
R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), which allows for
both SoCs to share a driver. R-Car M3-W+ lacks a few modules, so their
clocks must be nullified.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122941.12342-5-geert+renesas@glider.be
This patch adds the TPU clock on the R-Car r8a7795/r8a7796/r8a77965
SoCs.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Gen3 Hardware Manual Errata for Rev. 1.50 of Feb
12, 2019, the DRIF clocks have been renamed as follows:
DRIF0 to DRIF00
DRIF1 to DRIF01
DRIF2 to DRIF10
DRIF3 to DRIF11
DRIF4 to DRIF20
DRIF5 to DRIF21
DRIF6 to DRIF30
DRIF7 to DRIF31
Therefore, this patch renames the DRIF clocks from DRIFn to DRIFmm.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The clock sources of the AXI-bus clock (266.66 MHz) used for Audio-DMAC
DMA transfers are:
Channel R-Car H3 R-Car M3-W R-Car M3-N R-Car E3
---------------------------------------------------------------
Audio-DMAC0 S1D2 S1D2 S1D2 S1D2
Audio-DMAC1 S1D2 S1D2 S1D2 -
As a result, change the parent clocks of the Audio-DMAC{0,1} module
clocks on R-Car H3, R-Car M3-W, and R-Car M3-N to S1D2, and change the
parent clock of the Audio-DMAC0 module on R-Car E3 to S1D2.
NOTE: This information will be reflected in a future revision of the
R-Car Gen3 Hardware Manual.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car D3, RZ/G2M, and RZ/G2E]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The clock sources of the AXI BUS clock (266.66 MHz) used for SYS-DMAC
DMA transfers are:
Channel R-Car H3 R-Car M3-W R-Car M3-N
-------------------------------------------------
SYS-DMAC0 S0D3 S0D3 S0D3
SYS-DMAC1 S3D1 S3D1 S3D1
SYS-DMAC2 S3D1 S3D1 S3D1
As a result, change the parent clocks of the SYS-DMAC{1,2} module clocks
on R-Car H3, R-Car M3-W, and R-Car M3-N to S3D1.
NOTE: This information will be reflected in a future revision of the
R-Car Gen3 Hardware Manual.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update RZ/G2M]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Rev. 1.00, and the RZ/G2
Hardware Manual Rev. 0.61, the parent clock of the HS-USB module
clocks on R-Car Gen3 and RZ/G2 SoCs is S3D2.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[takeshi: Update R-Car H3, M3-N, and E3]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update RZ/G2M and RZ/G2E]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Rev. 1.00, and the RZ/G2
Hardware Manual Rev. 0.61, the parent clock of the EHCI/OHCI module
clocks on R-Car Gen3 and RZ/G2 SoCs is S3D2.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[takeshi: Update R-Car H3, M3-N, and E3]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update RZ/G2M and RZ/G2E]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
After recent reworking of Z and Z2 clk handling
CLK_TYPE_GEN3_Z and CLK_TYPE_GEN3_Z2 have come to have precisely
the same meaning. Remove this redundancy by eliminating the latter.
This is not expected to have any run-time effect.
As suggested by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Parameterise the offset of control bits within the FRQCRC register
for Z and Z2 clocks.
This is in preparation for supporting the Z2 clock on the R-Car E3
(r8a77990) SoC which uses a different offset for control bits to
other, already, supported SoCs.
As suggested by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Parameterise Z and Z2 clock fixed divisor to allow clocks with a fixed
divisor other than 2, the value used by all such clocks supported to date.
This is in preparation for supporting the Z2 clock on the R-Car E3
(r8a77990) SoC which has a fixed divisor of 4.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: squashed several patches; rewrote changelog; added r8a774a1 change]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Implement support for the CPEX clock on R-Car M3-W. This clock can be
selected as a clock source for CMT1 (Compare Match Timer Type 1).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car M3-W ES1.1. Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car M3-W SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
All other internal clock names have a period prepended.
Hence rename the internal RCLK from "rint" to ".r", and move it to the
section where all other internal clocks are defined.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds Z clock for R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.55 of
September 8, 2017, the parent clock of the INTC-AP module clock on R-Car
M3-W is S0D3.
This change has no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On some R-Car Gen3 SoCs (e.g. R-Car D3), PLL1 and PLL3 use a divider
value different from one. Extend struct rcar_gen3_cpg_pll_config to handle
this. As all multipliers and dividers are small, table size increase
can be kept limited by storing them in u8s instead of unsigned ints,
which saves ca. 0.5 KiB for a generic kernel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Add the "intc-ex" clock to the R8A7796 CPG MSSR driver.
According to information from the hardware team the INTC-EX
parent clock is CP. The next data sheet version will include
this information.
[takeshi.kihara.df: Ported from commit f099aa0757 ("clk: shmobile:
r8a7795: Add INTC-EX clock") to drivers/clk/renesas/r8a7796-cpg-mssr.c]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pass the mode pin states from the SoC-specific CPG/MSSR driver to the
R-Car Gen3 CPG driver core, as their state will be needed to make some
core clock configuration decisions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
