1. The I2C IP for both wmt and zhaoxin originates from VIA. Rename
common registers, functions, and variable names to follow the
VIAI2C_ and viai2c_ naming conventions for consistency and clarity.
2. rename i2c_dev to i2c, to shorten the length of a line.
3. rename wait_result to time_left, make it better to reflect the meaning
of the value returned by wait_for_completion_timeout().
4. remove TCR_MASTER_WRITE, its value is 0.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Since the I2C IP of both wmt and zhaoxin originates from VIA,
it is better to separate the common code first.
The common driver is named as i2c-viai2c-common.c.
Old i2c-wmt.c renamed to i2c-viai2c-wmt.c.
The MAINTAINERS file will be updated accordingly in upcoming commits.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some common initialization actions are put in the function
wmt_i2c_init(), which is convenient to share with zhaoxin.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Hu <hanshu-oc@zhaoxin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Read the ioclk property as reference clock if sclk not present in acpi
table to make it SOC agnostic.
In case, it's not populated from dts/acpi table, use the default clock
of 800 MHz which is optimal in either case of sclk/ioclk.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add watchdog timeout handling to cater to the unhandled warnings
seen during validation on boards with different I2C slaves.
This status code reflects the state that controller couldn't
receive any response from slave while being in non-idle state
and HW recommends to reset before any further bus access.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The macros for TWSI register's offset are generically
named, rename them to be platform specific macros by
adding 'OCTEON_REG' as prefix.
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
To support bus operations for high speed bus frequencies greater than
400KHZ following control bits need to be setup accordingly
- hs_mode (bit 0) field in Mode register to switch controller
between low-speed and high-speed frequency operating mode.
- Setup clock divisors for desired TWSI bus frequency using
FOSCL output frequency divisor (D):
0 - sets the divisor to 10 for low speed mode
1 - sets the divisor to 15 for high speed mode.
The TWSI bus output frequency, in master mode is based on:
TCLK = 100MHz / (THP + 2)
FOSCL = FSAMP / (M+1)×D = TCLK / (2 ^ N × (M + 1) × 15)
FSAMP = TCLK / 2 ^ N
where,
N is <2:0> and M is <6:3> of TWSI Clock Control Register
D is 10 for low speed or 15 for HS_MODE
With high speed mode support, HLC mode usage is limited to
low speed frequency (<=400KHz) bus transfers in hardware.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Handle changes to clock divisor logic for OcteonTX2 SoC family using
subsystem ID and using default reference clock source as 100MHz.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Add RISCV support to Cadence I2C Kconfig which is used in platform
such as the StarFive JH8100.
Signed-off-by: Eng Lee Teh <englee.teh@starfivetech.com>
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout and
simplify the logic a little.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Instead of repeatedly calling clk_get_rate for each transfer, lock
the clock rate and cache the value.
A deadlock has been observed while adding tlv320aic32x4 audio codec to
the system. When this clock provider adds its clock, the clk mutex is
locked already, it needs to access i2c, which in return needs the mutex
for clk_get_rate as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Annotate this variable as __ro_after_init to protect it from being
overwritten later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
i801 as only user of gpio i2c mux removed support for class-based device
instantiation on muxed busses. Class-based device instantiation is a
legacy mechanism and shouldn't be used in new code, therefore remove
support also here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Only remaining client driver supporting I2C_CLASS_SPD is jc42. This
type of thermal sensor can be found on several DDR3/DDR4 modules.
i2c_register_spd() instantiates also such thermal sensor i2c devices.
Since 893fef0bc6aa ("i2c: i801: Call i2c_register_spd for muxed child
segments") i2c_register_spd() is called also for the remaining use case,
systems with muxed SMBUS segments for SPD EEPROMs.
Therefore I2C_CLASS_SPD class-based instantiation isn't needed any longer
in this driver, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Granite Rapids-D has additional I2C controller that is enumerated via
ACPI. Add ACPI ID for it.
Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Remove of_node_put from node_ctrl and node struct device_nodes.
Move the declaration to initialization for ensuring scope sanity.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Abhinav Jain <jain.abhinav177@gmail.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The original change adds usage of i2c_root_adapter(), which is
implemented in i2c-mux.c. Therefore we can't use the multiplexing
if I2C_I801=y and I2C_MUX=m.
Handling the dependencies in the code would become unnecessarily
complex, therefore create a new config symbol.
Fixes: 893fef0bc6aa ("i2c: i801: Call i2c_register_spd for muxed child segments")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404042206.MjAQC32x-lkp@intel.com/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
There is at least one machine that uses this driver but does not
have support for inb()/outb() instructions.
Convert this to using ioport_map() so it can build on architectures
that don't provide these but work correctly on machines that require
using port I/O.
Fixes: 47c21d2d52e0 ("i2c: add HAS_IOPORT dependencies")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/lkml/CAMuHMdVUQ2WgtpYPYfO2T=itMmZ7w=geREqDtsP8Q3ODh9rxdw@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The Driver unintentionally programs ctrl reg to clear the fifo, which
happens after the start of transaction. Previously, this was not an issue
as it involved read-modified-write. However, this issue breaks i2c reads
on QEMU, as i2c-read is executed before guest starts programming control
register.
Fixes: ff0cf7bca630 ("i2c: cadence: Remove unnecessary register reads")
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Once the gpio mux driver binds to the "i2c-mux-gpio" platform device,
this creates the i2c adapters for the muxed child segments.
We can use the bus notifier mechanism to check for creation of the
child i2c adapters, and call i2c_register_spd() for them. This allows
to detect all DIMM's on systems with more than 8 memory slots.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Extend the RIIC driver to support the RZ/V2H(P) ("R9A09G057") SoC. It
accomplishes this by appending the compatible string list and passing
the RZ/V2H-specific OF data.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
With an increasing number of SoCs reusing this driver, each with slight
variations in the RIIC IP, it becomes necessary to support passing these
details as OF data. This approach simplifies the extension of the driver
for other SoCs.
This patch lays the groundwork for adding support for the Renesas RZ/V2H
SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Introduce helper functions for performing I2C read and write operations
in the RIIC driver.
These helper functions lay the groundwork for adding support for the
RZ/V2H SoC. This is essential because the register offsets for the RZ/V2H
SoC differ from those of the RZ/A SoC. By abstracting the read and write
operations, we can seamlessly adapt the driver to support different SoC
variants without extensive modifications.
This patch is part of the preparation process for integrating support for
the RZ/V2H SoC into the RIIC driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Baruch reported an OOPS when using the designware controller as target
only. Target-only modes break the assumption of one transfer function
always being available. Fix this by always checking the pointer in
__i2c_transfer.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Closes: https://lore.kernel.org/r/4269631780e5ba789cf1ae391eec1b959def7d99.1712761976.git.baruch@tkos.co.il
Fixes: 4b1acc43331d ("i2c: core changes for slave support")
[wsa: dropped the simplification in core-smbus to avoid theoretical regressions]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Amba bus core already sets owner, so driver does not need to.
Link: https://lore.kernel.org/r/20240326-module-owner-amba-v1-14-4517b091385b@linaro.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
The function using this is hidden in an #ifdef, so the variable
needs the same one for a clean W=1 build:
drivers/i2c/busses/i2c-pxa.c:327:26: error: 'icr_bits' defined but not used [-Werror=unused-const-variable=]
Fixes: d6a7b5f84b5c ("[ARM] 4827/1: fix two warnings in drivers/i2c/busses/i2c-pxa.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Commit 857cc04cdf50 ("i2c: i801: Add helper i801_get_block_len")
introduced a slight functional change: the status variable is now
overwritten with the length of an SMBUS tranasaction,
even in case of success.
This breaks the touchpad on at least my Lenovo P1:
rmi4_physical rmi4-00: Read PDT entry at 0x00e9 failed, code: -6.
rmi4_physical rmi4-00: RMI initial reset failed! Continuing in spite of this.
rmi4_physical rmi4-00: Read PDT entry at 0x00e9 failed, code: -6.
rmi4_physical rmi4-00: IRQ counting failed with code -6.
Fixes: 857cc04cdf50 ("i2c: i801: Add helper i801_get_block_len")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some hardware designs with multiple PCA954x devices use a reset GPIO
connected to all the muxes. Support this configuration by making use of
the reset controller framework which can deal with the shared reset
GPIOs. Fall back to the old GPIO descriptor method if the reset
controller framework is not enabled.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
This patch is followed by eight commits featuring improvements to
the Nomadik controller, such as simplification of the IRQ logic,
renaming of the private data structure, more efficient use of
FIELD_PREP/GET, GENMASK, etc., better time measurement with
ktime, and more.
Two device trees have been added, but those need to be applied
elsewhere.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQScDfrjQa34uOld1VLaeAVmJtMtbgUCZfLnNBYcYW5kaS5zaHl0
aUBrZXJuZWwub3JnAAoJENp4BWYm0y1uSSkBAKl75gzjiN2AglPaTUDfhCeux8yf
mISgvl4MWKCXXsZ5AQDjRiG+whrV7knOjS7L/r5owb30uF+Bv3d29sG4LVNsBQ==
=RubU
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-6.9-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
Théo adds support for the Mobileye EyeQ5-I2C in the bindings.
This patch is followed by eight commits featuring improvements to
the Nomadik controller, such as simplification of the IRQ logic,
renaming of the private data structure, more efficient use of
FIELD_PREP/GET, GENMASK, etc., better time measurement with
ktime, and more.
and are described by Andi in the merge commit
-----BEGIN PGP SIGNATURE-----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=Hm22
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Minor changes to the I2C core. Most changes are in drivers:
The i801 and designware drivers received most of the changes,
including refactorings and some additions.
Recovery changes for the iMX and iMX-LPI2C are now utilizing the
generic i2c support.
The Cadence driver now supports system suspend and resume.
The hisi, mpc, sh_mobile, and npcm drivers have undergone some
cleanups and improvements. Meanwhile, Uwe continues his work on
converting the "remove" callback to become a void function.
The pca954x mux driver now supports additional configurations, such as
isolating faulty channels and flushing stuck buses, among others.
Support has been added for Renesas r8a779h0, i.MX95 LPI2C, and
Microchip sam9x7. Meanwhile, Geert lays the groundwork for the
upcoming R-Car Gen4"
* tag 'i2c-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: sprd: Convert to platform remove callback returning void
Documentation: i2c: Document that client auto-detection is a legacy mechanism
i2c: remove redundant condition
i2c: rcar: Prepare for the advent of ARCH_RCAR_GEN4
i2c: imx-lpi2c: add generic GPIO recovery for LPI2C
i2c: cadence: Add system suspend and resume PM support
i2c: mpc: remove outdated macro
i2c: mpc: use proper binding for transfer timeouts
dt-bindings: i2c: mpc: use proper binding for transfer timeouts
i2c: smbus: Prepare i2c_register_spd for usage on muxed segments
i2c: constify the struct device_type usage
i2c: designware: Implement generic polling mode code for Wangxun 10Gb NIC
i2c: designware: Fix RX FIFO depth define on Wangxun 10Gb NIC
i2c: designware: Move interrupt handling functions before i2c_dw_xfer()
i2c: designware: Use accessors to DW_IC_INTR_MASK register
i2c: designware: Do not enable interrupts shortly in polling mode
i2c: designware: Uniform initialization flow for polling mode
dt-bindings: i2c: at91: Add sam9x7 compatible string
dt-bindings: i2c: imx-lpi2c: add i.MX95 LPI2C
i2c: Remove redundant comparison in npcm_i2c_reg_slave
...
heap optimizations".
- Kuan-Wei Chiu has also sped up the library sorting code in the series
"lib/sort: Optimize the number of swaps and comparisons".
- Alexey Gladkov has added the ability for code running within an IPC
namespace to alter its IPC and MQ limits. The series is "Allow to
change ipc/mq sysctls inside ipc namespace".
- Geert Uytterhoeven has contributed some dhrystone maintenance work in
the series "lib: dhry: miscellaneous cleanups".
- Ryusuke Konishi continues nilfs2 maintenance work in the series
"nilfs2: eliminate kmap and kmap_atomic calls"
"nilfs2: fix kernel bug at submit_bh_wbc()"
- Nathan Chancellor has updated our build tools requirements in the
series "Bump the minimum supported version of LLVM to 13.0.1".
- Muhammad Usama Anjum continues with the selftests maintenance work in
the series "selftests/mm: Improve run_vmtests.sh".
- Oleg Nesterov has done some maintenance work against the signal code
in the series "get_signal: minor cleanups and fix".
Plus the usual shower of singleton patches in various parts of the tree.
Please see the individual changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZfMnvgAKCRDdBJ7gKXxA
jjKMAP4/Upq07D4wjkMVPb+QrkipbbLpdcgJ++q3z6rba4zhPQD+M3SFriIJk/Xh
tKVmvihFxfAhdDthseXcIf1nBjMALwY=
=8rVc
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2024-03-14-09-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- Kuan-Wei Chiu has developed the well-named series "lib min_heap: Min
heap optimizations".
- Kuan-Wei Chiu has also sped up the library sorting code in the series
"lib/sort: Optimize the number of swaps and comparisons".
- Alexey Gladkov has added the ability for code running within an IPC
namespace to alter its IPC and MQ limits. The series is "Allow to
change ipc/mq sysctls inside ipc namespace".
- Geert Uytterhoeven has contributed some dhrystone maintenance work in
the series "lib: dhry: miscellaneous cleanups".
- Ryusuke Konishi continues nilfs2 maintenance work in the series
"nilfs2: eliminate kmap and kmap_atomic calls"
"nilfs2: fix kernel bug at submit_bh_wbc()"
- Nathan Chancellor has updated our build tools requirements in the
series "Bump the minimum supported version of LLVM to 13.0.1".
- Muhammad Usama Anjum continues with the selftests maintenance work in
the series "selftests/mm: Improve run_vmtests.sh".
- Oleg Nesterov has done some maintenance work against the signal code
in the series "get_signal: minor cleanups and fix".
Plus the usual shower of singleton patches in various parts of the tree.
Please see the individual changelogs for details.
* tag 'mm-nonmm-stable-2024-03-14-09-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (77 commits)
nilfs2: prevent kernel bug at submit_bh_wbc()
nilfs2: fix failure to detect DAT corruption in btree and direct mappings
ocfs2: enable ocfs2_listxattr for special files
ocfs2: remove SLAB_MEM_SPREAD flag usage
assoc_array: fix the return value in assoc_array_insert_mid_shortcut()
buildid: use kmap_local_page()
watchdog/core: remove sysctl handlers from public header
nilfs2: use div64_ul() instead of do_div()
mul_u64_u64_div_u64: increase precision by conditionally swapping a and b
kexec: copy only happens before uchunk goes to zero
get_signal: don't initialize ksig->info if SIGNAL_GROUP_EXIT/group_exec_task
get_signal: hide_si_addr_tag_bits: fix the usage of uninitialized ksig
get_signal: don't abuse ksig->info.si_signo and ksig->sig
const_structs.checkpatch: add device_type
Normalise "name (ad@dr)" MODULE_AUTHORs to "name <ad@dr>"
dyndbg: replace kstrdup() + strchr() with kstrdup_and_replace()
list: leverage list_is_head() for list_entry_is_head()
nilfs2: MAINTAINERS: drop unreachable project mirror site
smp: make __smp_processor_id() 0-argument macro
fat: fix uninitialized field in nostale filehandles
...
