On the RAH registers there are semantic differences on the meaning of
the "queue" parameter for traffic steering depending on the controller
model: there is the 82575 meaning, which "queue" means a RX Hardware
Queue, and the i350 meaning, where it is a reception pool.
The previous behaviour was having no effect for i210 based controllers
because the QSEL bit of the RAH register wasn't being set.
This patch separates the condition in discrete cases, so the different
handling is clearer.
Fixes: 83c21335c876 ("igb: improve MAC filter handling")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the check on FRA_L3MDEV attribute to helper to improve the
readability of fib_nl2rule. Update the extack messages to be
clear when the configuration option is disabled versus an invalid
value has been passed.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's currently written as:
if (!tchunk->tsn_gap_acked) { [1]
tchunk->tsn_gap_acked = 1;
...
}
if (TSN_lte(tsn, sack_ctsn)) {
if (!tchunk->tsn_gap_acked) {
/* SFR-CACC processing */
...
}
}
Which causes the SFR-CACC processing on ack reception to never process,
as tchunk->tsn_gap_acked is always true by then. Block [1] was
moved to that position by the commit marked below.
This patch fixes it by doing SFR-CACC processing earlier, before
tsn_gap_acked is set to true.
Fixes: 31b02e154940 ("sctp: Failover transmitted list on transport delete")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_make_sack() make changes to the asoc and this cast is just
bypassing the const attribute. As there is no need to have the const
there, just remove it and fix the violation.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends NTF_EXT_LEARNED support to the neighbour system.
Example use-case: An Ethernet VPN implementation (eg in FRR routing suite)
can use this flag to add dynamic reachable external neigh entires
learned via control plane. The use of neigh NTF_EXT_LEARNED in this
patch is consistent with its use with bridge and vxlan fdb entries.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addrconf_ifdown() evaluates keep_addr_on_down state twice. There
is no need to do it.
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ECMP (equal-cost multipath) hashes are typically computed on the packets'
5-tuple(src IP, dst IP, src port, dst port, L4 proto).
For encapsulated packets, the L4 data is not readily available and ECMP
hashing will often revert to (src IP, dst IP). This will lead to traffic
polarization on a single ECMP path, causing congestion and waste of network
capacity.
In IPv6, the 20-bit flow label field is also used as part of the ECMP hash.
In the lack of L4 data, the hashing will be on (src IP, dst IP, flow
label). Having a non-zero flow label is thus important for proper traffic
load balancing when L4 data is unavailable (i.e., when packets are
encapsulated).
Currently, the seg6_do_srh_encap() function extracts the original packet's
flow label and set it as the outer IPv6 flow label. There are two issues
with this behaviour:
a) There is no guarantee that the inner flow label is set by the source.
b) If the original packet is not IPv6, the flow label will be set to
zero (e.g., IPv4 or L2 encap).
This patch adds a function, named seg6_make_flowlabel(), that computes a
flow label from a given skb. It supports IPv6, IPv4 and L2 payloads, and
leverages the per namespace 'seg6_flowlabel" sysctl value.
The currently support behaviours are as follows:
-1 set flowlabel to zero.
0 copy flowlabel from Inner paceket in case of Inner IPv6
(Set flowlabel to 0 in case IPv4/L2)
1 Compute the flowlabel using seg6_make_flowlabel()
This patch has been tested for IPv6, IPv4, and L2 traffic.
Signed-off-by: Ahmed Abdelsalam <amsalam20@gmail.com>
Acked-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MDIO busses will error out when trying to read a phy address with no
phy present at that address. In that case, probing the bus will fail
because __mdiobus_register() is scanning the bus for all possible phys
addresses.
In case MII_PHYSID1 returns -EIO or -ENODEV, consider there is no phy at
this address and set the phy ID to 0xffffffff which is then properly
handled in get_phy_device().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the order of the parameters passes to 'hlist_add_behind()' was
inverted, the 'parent' node was added "behind" the 'input', as input
is not in the list, this causes the 'input' node to be lost.
Fixes: 0e71def25281 ("igb: add support of RX network flow classification")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original implementation for macvlan offload has us performing a full
port reset every time we added a new macvlan. This shouldn't be necessary
and can be avoided with a few behavior changes.
This patches updates the logic for the queues so that we have essentially 3
possible configurations for macvlan offload. They consist of 15 macvlans
with 4 queues per macvlan, 31 macvlans with 2 queues per macvlan, and 63
macvlans with 1 queue per macvlan. As macvlans are added you will encounter
up to 3 total resets if you add all the way up to 63, and after that the
device will stay in the mode supporting up to 63 macvlans until the L2FW
flag is cleared.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch drops the real_adapter member from the fwd_adapter structure.
The general idea behind the change is that the real_adapter is carrying
unnecessary data since we could always just grab the adapter structure
from netdev_priv(macvlan->lowerdev) if we really needed to get at it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the ixgbe and fm10k drivers support destination filtering.
Instead of adding a ton of complexity to support either source or passthru
mode we can instead just avoid offloading them for now. Doing this we avoid
leaking packets into interfaces that aren't meant to receive them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch provides a basic function to allow a lower device to disable
macvlan offload if it was previously enabled on a given macvlan. The idea
here is to allow for recovery from failure should the lowerdev run out of
resources.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a function indicating if a given macvlan can fully supports
destination filtering, especially as it relates to unicast traffic. For
those macvlan interfaces that do not support destination filtering such
passthru or source mode filtering we should not be enabling offload
support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It doesn't make sense to define macvlan_count_rx as a static inline and
then add a forward declaration after that as an extern. I am dropping the
extern declaration since it seems like it is something that likely got
missed when the function was made an inline.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop dead code now that we shouldn't be receiving broadcast or multicast
frames on the queues associated to the macvlan netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use a software path for packets that are
going to be locally switched between two macvlan interfaces on the same
device. In addition we resort to software replication of broadcast and
multicast packets instead of offloading that to hardware.
The general idea is that using the device for east/west traffic local to
the system is extremely inefficient. We can only support up to whatever the
PCIe limit is for any given device so this caps us at somewhere around 20G
for devices supported by ixgbe. This is compounded even further when you
take broadcast and multicast into account as a single 10G port can come to
a crawl as a packet is replicated up to 60+ times in some cases. In order
to get away from that I am implementing changes so that we handle
broadcast/multicast replication and east/west local traffic all in
software.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change renames the fwd_priv member to accel_priv as this more
accurately reflects the actual purpose of this value. In addition I am
adding an accessor which will allow us to further abstract this in the
future if needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop the code for handling macvlan specific unicast lists. It isn't needed
since we don't take any efforts to maintain it when we bring the interface
up and it takes the slow path anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 2a5418a13fcf ("bpf: improve dead code sanitizing") replaced dead
code with a series of ja-1 instructions, for safety. That made JIT
compilation much more complex for some BPF programs. One instance of such
programs is, for example:
bool flag = false
...
/* A bunch of other code */
...
if (flag)
do_something()
In some cases llvm is not able to remove at compile time the code for
do_something(), so the generated BPF program ends up with a large amount
of dead instructions. In one specific real life example, there are two
series of ~500 and ~1000 dead instructions in the program. When the
verifier replaces them with a series of ja-1 instructions, it causes an
interesting behavior at JIT time.
During the first pass, since all the instructions are estimated at 64
bytes, the ja-1 instructions end up being translated as 5 bytes JMP
instructions (0xE9), since the jump offsets become increasingly large (>
127) as each instruction gets discovered to be 5 bytes instead of the
estimated 64.
Starting from the second pass, the first N instructions of the ja-1
sequence get translated into 2 bytes JMPs (0xEB) because the jump offsets
become <= 127 this time. In particular, N is defined as roughly 127 / (5
- 2) ~= 42. So, each further pass will make the subsequent N JMP
instructions shrink from 5 to 2 bytes, making the image shrink every time.
This means that in order to have the entire program converge, there need
to be, in the real example above, at least ~1000 / 42 ~= 24 passes just
for translating the dead code. If we add this number to the passes needed
to translate the other non dead code, it brings such program to 40+
passes, and JIT doesn't complete. Ultimately the userspace loader fails
because such BPF program was supposed to be part of a prog array owner
being JITed.
While it is certainly possible to try to refactor such programs to help
the compiler remove dead code, the behavior is not really intuitive and it
puts further burden on the BPF developer who is not expecting such
behavior. To make things worse, such programs are working just fine in all
the kernel releases prior to the ja-1 fix.
A possible approach to mitigate this behavior consists into noticing that
for ja-1 instructions we don't really need to rely on the estimated size
of the previous and current instructions, we know that a -1 BPF jump
offset can be safely translated into a 0xEB instruction with a jump offset
of -2.
Such fix brings the BPF program in the previous example to complete again
in ~9 passes.
Fixes: 2a5418a13fcf ("bpf: improve dead code sanitizing")
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski says:
====================
This set adds an optimization run to the NFP jit to turn ADD and SUB
instructions with negative immediate into the opposite operation with
a positive immediate. NFP can fit small immediates into the instructions
but it can't ever fit negative immediates. Addition of small negative
immediates is quite common in BPF programs for stack address calculations,
therefore this optimization gives us non-negligible savings in instruction
count (up to 4%).
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Comparison instruction requires a subtraction. If the constant
is negative we are more likely to fit it into a NFP instruction
directly if we change the sign and use addition.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There are quite a few compare instructions now, use a table
to translate BPF instruction code to NFP instruction parameters
instead of parameterizing helpers. This saves LOC and makes
future extensions easier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP instruction set can fit small immediates into the instruction.
Negative integers, however, will never fit because they will have
highest bit set. If we swap the ALU op between ADD and SUB and
negate the constant we have a better chance of fitting small negative
integers into the instruction itself and saving one or two cycles.
immed[gprB_21, 0xfffffffc]
alu[gprA_4, gprA_4, +, gprB_21], gpr_wrboth
immed[gprB_21, 0xffffffff]
alu[gprA_5, gprA_5, +carry, gprB_21], gpr_wrboth
now becomes:
alu[gprA_4, gprA_4, -, 4], gpr_wrboth
alu[gprA_5, gprA_5, -carry, 0], gpr_wrboth
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The percpu metadata_dst might carry the stale ip_tunnel_info
and cause incorrect behavior. When mixing tests using ipv4/ipv6
bpf vxlan and geneve tunnel, the ipv6 tunnel info incorrectly uses
ipv4's src ip addr as its ipv6 src address, because the previous
tunnel info does not clean up. The patch zeros the fields in
ip_tunnel_info.
Signed-off-by: William Tu <u9012063@gmail.com>
Reported-by: Yifeng Sun <pkusunyifeng@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull userns bug fix from Eric Biederman:
"Just a small fix to properly set the return code on error"
* 'userns-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
commoncap: Handle memory allocation failure.
When test_sockmap was running outside of selftests and was not being
run by build bots it was reasonable to spend significant amount of
time running various tests. The number of tests is high because many
different I/O iterators are run.
However, now that test_sockmap is part of selftests rather than
iterate through all I/O sides only test a minimal set of min/max
values along with a few "normal" I/O ops. Also remove the long
running tests. They can be run from other test frameworks on a regular
cadence.
This significanly reduces runtime of test_sockmap.
Before:
$ time sudo ./test_sockmap > /dev/null
real 4m47.521s
user 0m0.370s
sys 0m3.131s
After:
$ time sudo ./test_sockmap > /dev/null
real 0m0.514s
user 0m0.104s
sys 0m0.430s
The CLI is still available for users that want to test the long
running tests that do the larger send/recv tests.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend says:
====================
This series moves ./samples/sockmap into BPF selftests. There are a
few good reasons to do this. First, by pushing this into selftests
the tests will be run automatically. Second, sockmap was not really
a sample of anything anymore, but rather a large set of tests.
Note: There are three recent fixes outstanding against bpf branch
that can be detected occasionally by the automated tests here.
https://patchwork.ozlabs.org/patch/903138/https://patchwork.ozlabs.org/patch/903139/https://patchwork.ozlabs.org/patch/903140/
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The BPF sample sockmap is redundant now that equivelant tests exist
in the BPF selftests. Lets remove this sample and only keep the
selftest version that will be run as part of the selftest suite.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This adds a new test program test_sockmap which is the old sample
sockmap program. By moving the sample program here we can now run it
as part of the self tests suite. To support this a populate_progs()
routine is added to load programs and maps which was previously done
with load_bpf_file(). This is needed because self test libs do not
provide a similar routine. Also we now use the cgroup_helpers
routines to manage cgroup use instead of manually creating one and
supplying it to the CLI.
Notice we keep the CLI around though because it is useful for dbg
and specialized testing.
To run use ./test_sockmap and the result should be,
Summary 660 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If no options are passed to sockmap after this patch we run a set of
tests using various options and sendmsg/sendpage sizes. This replaces
the sockmap_test.sh script.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
By moving sockmap_test from shell script into C we can run it directly
from selftests, but we can also push the input/output around in proper
structures.
However, keep the CLI options around because they are useful for
debugging when a paticular pattern of msghdr or sockmap options
trips up the sockmap code path.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since test_sock_addr is not supposed to run by itself,
remove it from TEST_GEN_PROGS and add it to
TEST_GEN_PROGS_EXTENDED. This way, run_tests will
not run test_sock_addr. The corresponding test to run
is test_sock_addr.sh.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull networking fixes from David Miller:
1) Fix rtnl deadlock in ipvs, from Julian Anastasov.
2) s390 qeth fixes from Julian Wiedmann (control IO completion stalls,
bad MAC address update sequence, request side races on command IO
timeouts).
3) Handle seq_file overflow properly in l2tp, from Guillaume Nault.
4) Fix VLAN priority mappings in cpsw driver, from Ivan Khoronzhuk.
5) Packet scheduler ife action fixes (malformed TLV lengths, etc.) from
Alexander Aring.
6) Fix out of bounds access in tcp md5 option parser, from Jann Horn.
7) Missing netlink attribute policies in rtm_ipv6_policy table, from
Eric Dumazet.
8) Missing socket address length checks in l2tp and pppoe connect, from
Guillaume Nault.
9) Fix netconsole over team and bonding, from Xin Long.
10) Fix race with AF_PACKET socket state bitfields, from Willem de
Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (51 commits)
ice: Fix insufficient memory issue in ice_aq_manage_mac_read
sfc: ARFS filter IDs
net: ethtool: Add missing kernel doc for FEC parameters
packet: fix bitfield update race
ice: Do not check INTEVENT bit for OICR interrupts
ice: Fix incorrect comment for action type
ice: Fix initialization for num_nodes_added
igb: Fix the transmission mode of queue 0 for Qav mode
ixgbevf: ensure xdp_ring resources are free'd on error exit
team: fix netconsole setup over team
amd-xgbe: Only use the SFP supported transceiver signals
amd-xgbe: Improve KR auto-negotiation and training
amd-xgbe: Add pre/post auto-negotiation phy hooks
pppoe: check sockaddr length in pppoe_connect()
l2tp: check sockaddr length in pppol2tp_connect()
net: phy: marvell: clear wol event before setting it
ipv6: add RTA_TABLE and RTA_PREFSRC to rtm_ipv6_policy
bonding: do not set slave_dev npinfo before slave_enable_netpoll in bond_enslave
tcp: don't read out-of-bounds opsize
ibmvnic: Clean actual number of RX or TX pools
...
Paul Chaignon says:
====================
Currently, helpers that expect ARG_PTR_TO_MAP_KEY and ARG_PTR_TO_MAP_VALUE
can only access stack and packet memory. This patchset allows these
helpers to directly access map values by passing registers of type
PTR_TO_MAP_VALUE.
The first patch changes the verifier; the second adds new test cases.
The first three versions of this patchset were sent on the iovisor-dev
mailing list only.
Changelogs:
Changes in v5:
- Refactor using check_helper_mem_access.
Changes in v4:
- Rebase.
Changes in v3:
- Bug fixes.
- Negative test cases.
Changes in v2:
- Additional test cases for adjusted maps.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds new test cases for accesses to map values from map
helpers.
Signed-off-by: Paul Chaignon <paul.chaignon@orange.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Helpers that expect ARG_PTR_TO_MAP_KEY and ARG_PTR_TO_MAP_VALUE can only
access stack and packet memory. Allow these helpers to directly access
map values by passing registers of type PTR_TO_MAP_VALUE.
This change removes the need for an extra copy to the stack when using a
map value to perform a second map lookup, as in the following:
struct bpf_map_def SEC("maps") infobyreq = {
.type = BPF_MAP_TYPE_HASHMAP,
.key_size = sizeof(struct request *),
.value_size = sizeof(struct info_t),
.max_entries = 1024,
};
struct bpf_map_def SEC("maps") counts = {
.type = BPF_MAP_TYPE_HASHMAP,
.key_size = sizeof(struct info_t),
.value_size = sizeof(u64),
.max_entries = 1024,
};
SEC("kprobe/blk_account_io_start")
int bpf_blk_account_io_start(struct pt_regs *ctx)
{
struct info_t *info = bpf_map_lookup_elem(&infobyreq, &ctx->di);
u64 *count = bpf_map_lookup_elem(&counts, info);
(*count)++;
}
Signed-off-by: Paul Chaignon <paul.chaignon@orange.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Eyal Birger says:
====================
This patchset adds support for fetching XFRM state information from
an eBPF program called from TC.
The first patch introduces a helper for fetching an XFRM state from the
skb's secpath. The XFRM state is modeled using a new virtual struct which
contains the SPI, peer address, and reqid values of the state; This struct
can be extended in the future to provide additional state information.
The second patch adds a test example in test_tunnel_bpf.sh. The sample
validates the correct extraction of state information by the eBPF program.
v3:
- Kept SPI and peer IPv4 address in state in network byte order
following suggestion from Alexei Starovoitov
v2:
- Fixed two comments by Daniel Borkmann:
- disallow reserved flags in helper call
- avoid compiling in helper code when CONFIG_XFRM is off
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a test for fetching xfrm state parameters from a tc program running
on ingress.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit introduces a helper which allows fetching xfrm state
parameters by eBPF programs attached to TC.
Prototype:
bpf_skb_get_xfrm_state(skb, index, xfrm_state, size, flags)
skb: pointer to skb
index: the index in the skb xfrm_state secpath array
xfrm_state: pointer to 'struct bpf_xfrm_state'
size: size of 'struct bpf_xfrm_state'
flags: reserved for future extensions
The helper returns 0 on success. Non zero if no xfrm state at the index
is found - or non exists at all.
struct bpf_xfrm_state currently includes the SPI, peer IPv4/IPv6
address and the reqid; it can be further extended by adding elements to
its end - indicating the populated fields by the 'size' argument -
keeping backwards compatibility.
Typical usage:
struct bpf_xfrm_state x = {};
bpf_skb_get_xfrm_state(skb, 0, &x, sizeof(x), 0);
...
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Swap VF representor tx and rx interface statistics since it is a
virtual switchdev port and tx for VM should be rx for VF representor
and vice-versa.
Signed-off-by: Srinivas Jampala <srinivasa.jampala@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_remove_exception_rt() is called under rcu_read_lock() only.
We lock rt6_exception_lock a bit later, so we do not hold
rt6_exception_lock yet.
Fixes: 8a14e46f1402 ("net/ipv6: Fix missing rcu dereferences on from")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: David Ahern <dsahern@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-04-24
This series contains fixes to ixgbevf, igb and ice drivers.
Colin Ian King fixes the return value on error for the new XDP support
that went into ixgbevf for 4.17.
Vinicius provides a fix for queue 0 for igb, which was not receiving all
the credits it needed when QAV mode was enabled.
Anirudh provides several fixes for the new ice driver, starting with
properly initializing num_nodes_added to zero. Fixed up a code comment
to better reflect what is really going on in the code. Fixed how to
detect if an OICR interrupt has occurred to a more reliable method.
Md Fahad fixes the ice driver to allocate the right amount of memory
when reading and storing the devices MAC addresses. The device can have
up to 2 MAC addresses (LAN and WoL), while WoL is currently not
supported, we need to ensure it can be properly handled when support is
added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A duplicated null check on sgout is redundant as it is known to be
already true because of the identical earlier check. Remove it.
Detected by cppcheck:
net/tls/tls_sw.c:696: (warning) Identical inner 'if' condition is always
true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check port->rev_info.major >= 6 is being performed twice, thus
the inner second check is always true and is redundant, hence it
can be removed. Detected by cppcheck.
drivers/net/ethernet/freescale/fman/fman_port.c:1394]: (warning)
Identical inner 'if' condition is always true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the MAC read operation, the device can return up to two (LAN and WoL)
MAC addresses. Without access to adequate memory, the device will return
an error. Fixed this by allocating the right amount of memory. Also, logic
to detect and copy the LAN MAC address into the port_info structure has
been added. Note that the WoL MAC address is ignored currently as the WoL
feature isn't supported yet.
Fixes: dc49c7723676 ("ice: Get MAC/PHY/link info and scheduler topology")
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The strscpy() was a recent fix (net: qed: use correct strncpy() size) to
prevent passing the length of the source buffer to strncpy() and guarantee
null termination.
It misses the goal of overwriting only the first 3 characters in
"???_BIG_RAM" and "???_RAM" while keeping the rest of the string.
Use strncpy() with the length of 3, without null termination.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
