The previous conversion back to .probe() applied in commit 9abcd24002bf
("ASoC: Switch i2c drivers back to use .probe()") was created based on
v6.3. Since then two more drivers were added which need to be convert
back in the same way before eventually .probe_new() can be dropped from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230612070608.836186-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use existing define for WSA883X_GLOBAL_PA_ENABLE instead of hard-coded
value, just like in other places in this driver.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230607171326.179527-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch is to manage HSD feature for power saving. The detail is to
disable HSD feature after the headset detection is done. When the jack
is inserted, the HSD feature will be enabled again.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Link: https://lore.kernel.org/r/20230531075334.168637-1-CTLIN0@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:
This patch series handles a few issues related to the ES8316 audio
codec, discovered while doing some testing on the Rock 5B board.
When using the codec through the generic audio graph card, there are at
least two calls of es8316_set_dai_sysclk(), with the effect of limiting
the allowed sample rates according to the MCLK/LRCK ratios supported by
the codec:
1. During audio card setup, to set the initial MCLK - see
asoc_simple_init_dai().
2. Before opening a stream, to update MCLK, according to the stream
sample rate and the multiplication factor - see
asoc_simple_hw_params().
In some cases the initial MCLK might be set to a frequency that doesn't
match any of the supported ratios, e.g. 12287999 instead of 12288000,
which is only 1 Hz below the supported clock, as that is what the
hardware reports. This creates an empty list of rate constraints, which
is further passed to snd_pcm_hw_constraint_list() via
es8316_pcm_startup(), and causes the following error on the very first
access of the sound card:
$ speaker-test -D hw:Analog,0 -F S16_LE -c 2 -t wav
Broken configuration for playback: no configurations available: Invalid argument
Setting of hwparams failed: Invalid argument
Note that all subsequent retries succeed thanks to the updated MCLK set
at point 2 above, which uses a computed frequency value instead of a
reading from the hardware registers. Normally this would have mitigated
the issue, but es8316_pcm_startup() executes before the 2nd call to
es8316_set_dai_sysclk(), hence it cannot make use of the updated
constraints.
Since es8316_pcm_hw_params() performs anyway a final validation of MCLK
against the stream sample rate and the supported MCLK/LRCK ratios, fix
the issue by ensuring that sysclk_constraints list is only set when at
least one supported sample rate is autodetected by the codec.
Fixes: b8b88b70875a ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-3-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The following error occurs when trying to restore a previously saved
ALSA mixer state (tested on a Rock 5B board):
$ alsactl --no-ucm -f /tmp/asound.state store hw:Analog
$ alsactl --no-ucm -I -f /tmp/asound.state restore hw:Analog
alsactl: set_control:1475: Cannot write control '2:0:0:ALC Capture Target Volume:0' : Invalid argument
According to ES8316 datasheet, the register at address 0x2B, which is
related to the above mixer control, contains by default the value 0xB0.
Considering the corresponding ALC target bits (ALCLVL) are 7:4, the
control is initialized with 11, which is one step above the maximum
value allowed by the driver:
ALCLVL | dB gain
-------+--------
0000 | -16.5
0001 | -15.0
0010 | -13.5
.... | .....
0111 | -6.0
1000 | -4.5
1001 | -3.0
1010 | -1.5
.... | .....
1111 | -1.5
The tests performed using the VU meter feature (--vumeter=TYPE) of
arecord/aplay confirm the specs are correct and there is no measured
gain if the 1011-1111 range would have been mapped to 0 dB:
dB gain | VU meter %
--------+-----------
-6.0 | 30-31
-4.5 | 35-36
-3.0 | 42-43
-1.5 | 50-51
0.0 | 50-51
Increment the max value allowed for ALC Capture Target Volume control,
so that it matches the hardware default. Additionally, update the
related TLV to prevent an artificial extension of the dB gain range.
Fixes: b8b88b70875a ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 4.8Mhz 9.6Mhz and 19.2MHz SCLK values
for MCLK 12MHz and 12.288MHz requested by Intel.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230524125236.57149-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from David Rau <David.Rau.opensource@dm.renesas.com>:
This patchset adds the support of DA7219 Jack insertion detection
polarity selection.
The first patch replaces the old txt binding with a new schema binding.
The second patch adds `dlg,jack-ins-det-pty` property for Jack
insertion detection polarity selection.
The last patch adds the driver support for this topic.
The series has been verified on the DA7219 development kit.
Merge series from Trevor Wu <trevor.wu@mediatek.com>:
The patch series includes a kselftest fix and changes for extending
driver capability to support more use cases.
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
Series removes the pm_runtime.h inclusion in files where
APIs exported though pm_runtime.h are not used. In case
of files that make use of pm.h which comes form pm_runtime.h
added patch 2/2.
Originally, lineout playback source can only be DAC_3RD. Some SoC
masters only support stereo MTKAIF outputs, so lineout path can't be
used in such case.
MTKAIF connections are as follows.
MOSI0 -> DAC_L
MOSI1 -> DAC_R
MOSI2 -> DAC_3rd
In the patch, lineout playback source can be chosen between DAC_L and
DAC_3rd, so sound can be outputted via lineout even though SoC only
supports stereo MTKAIF outputs.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20230508071532.21665-5-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
kselftest tries to read/write the default value. The default register
value of playback gain is 0x1F(mute), but max gain we specified is 0x12.
The range of the control is 0x0~0x12 and mute(0x1F) is only used in the
driver internally. To solve the problem, implement a new callback
mt6359_get_playback_volsw to report user configured volume instead of
the register value.
In addition, update max of "Headset Volume" to 0x12, so it can match the
maximum seen on latest data sheet.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20230508071532.21665-3-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are three output data pins MISO0, MISO1 and MISO2 for mt6359.
UL_SRC should be enabled when MISO0 or MISO1 is used, and UL_SRC_34
should be enabled when MISO2 is used.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20230508071532.21665-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support of selecting insertion detection polarity
- Default polarity (Low)
- Inverted polarity (High)
Correct the keywords of parsing `dlg,jack-det-rate`
bases on the new DT binding.
Signed-off-by: David Rau <David.Rau.opensource@dm.renesas.com>
Link: https://lore.kernel.org/r/20230523161821.4260-4-David.Rau.opensource@dm.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not include pm_runtime.h header in files where runtime PM support is
not implemented. Use pm.h instead as suspend to RAM specific
implementation is available.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230517094903.2895238-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not include pm_runtime.h header in files where APIs exported by
pm_runtime.h are not used.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com> # for omap-mcbsp-st.c
Link: https://lore.kernel.org/r/20230517094903.2895238-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding pre-charge actions to make FEPGA power stable faster. It
improve the recording quality at the beginning. Thus, it is also
meaningfully to decrease the final adc delay time.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Link: https://lore.kernel.org/r/20230523083303.98436-1-CTLIN0@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
First two patches are bugfixes.
Third patch skips the overhead of rebooting the amp after applying
firmware files when we know that it isn't necessary.
If the device is in secure mode it's unnecessary to send a SHUTDOWN and
SYSTEM_RESET around the firmware download. It could only be patching
insecure tunings. A tuning patch doesn't need a SHUTDOWN and only needs
a REINIT afterwards. This will reduce the overhead of exiting system
suspend in secure mode.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/Message-Id: <20230518150250.1121006-4-rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire bus accesses must be performed under the guard of a pm_runtime
request, in this case the write was being performed just after the
request had been put() and so the bus could not be guaranteed to be
available.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/Message-Id: <20230518150250.1121006-3-rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each time we go through dsp_work() it does a devm_kasprintf() to
allocate memory to hold the part name string. It's not strictly a memory
leak because devm will free it all if the driver is removed. But we keep
allocating more and more memory to hold the same string.
Move the allocation so that it is performed after the version and
secured state information is gathered and handle allocation errors.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/Message-Id: <20230518150250.1121006-2-rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Paweł Anikiel <pan@semihalf.com>:
The Google Chameleon v3 is a device made for testing audio and video
paths of other devices. This patchset adds support for ASoC audio on
this device. It has two audio sources: HDMI audio from the it68051 chip
(RX only), and analog audio from the ssm2603 chip (RX and TX).
The patchset adds the ASoC platform and codec drivers.
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-13-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-12-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-10-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-9-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Driver in its update status callback stores Soundwire device status in
state container but it never uses it later. Simplify the code a bit.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230518072753.7361-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Update the driver to use the new ASoC core control notify helper.
This also fixes a bug where the control would not be found if the
CODEC was given a name prefix.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512122838.243002-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
Flush the SoundWire interrupt handler work instead of cancelling it.
When a SoundWire interrupt is triggered the pm_runtime is held
until the work has completed. It's therefore unsafe to cancel
the work, it must be flushed.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512144237.739000-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
