Currently whenever link AP beacon is assigned, sdata->u.ap.active flag is
set and whenever it is brought down, the flag is reset. However, with MLO,
all the links of the same MLD would use the same sdata. Hence there is no
need to set/reset for each link up/down. Also, resetting it when only one
of the links went down is not desirable.
Add changes to set the active flag only when first link is assigned
beacon. Similarly, add changes to reset that flag only when last link is
brought down.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240409094017.3165560-1-quic_adisi@quicinc.com
[remove unnecessary check before constant true assignment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the Return: annotation instead of spelling out "Returns" in
the documentation, for both sta_info_flush()/__sta_info_flush().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the unlikely event that link_use_channel fails while activating a
link, mac80211 would go into a bad state. Unfortunately, we cannot
completely avoid failures from drivers in this case.
However, what we can do is to just continue internally anyway and assume
the driver is going to trigger a recovery flow from its side. Doing that
means that we at least have a consistent state in mac80211 allowing such
a recovery flow to succeed.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240418115219.1129e89f4b55.I6299678353e50e88b55c99b0bce15c64b52c2804@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need for a label/goto here, the only thing is
that drv_assign_vif_chanctx() must succeed to set 'conf'
and add the new context to the list, the remaining code
is (and must be) the same regardless.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240418115219.a94852030d33.I9d647178ab25636372ed79e5312c68a06e0bf60c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When searching for a chanctx for re-use, it's later adjusted and
assigned. It may also be that another one is already assigned to
the link in question, so unassign can also happen. In short, the
driver is called multiple times. During these callbacks, it may
thus change active links (on another interface), which then can
in turn cause the found chanctx (that's going to be reused) to
get removed and freed.
To avoid this, temporarily assign it to the reserved chanctx and
track the link that wants to use it in the reserved_links list.
This causes the ieee80211_chanctx_refcount() to be increased by
one during these operations, thus avoiding the free.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240418115219.94ea84c8ee1e.I0b247dbc0cd937ae6367bc0fc7e8d156b5d5f9b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a link switch work was queued, and then a restart happened, the
worker might be executed before the reconfig, and obviously it will fail
(the HW might not respond to updates etc.)
So, don't perform the switch if we are in reconfig, instead - do it
at the end of the reconfig.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415112355.1ef1008e3a0a.I19add3f2152dcfd55a759de97b1d09265c1cde98@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's an issue in that when we disconnect from an AP
due to the AP switching to an unsupported channel, we
might not tell the driver about this before we try to
send the deauth. If the underlying implementation has
detected the quiet CSA, this may cause issues if this
is the only active link. Avoid this by transmitting
(and flushing) the deauth only when there's an active
link available that's not affected by quiet CSA.
Since this introduces link->u.mgd.csa_blocked_tx and we
no longer check sdata->csa_blocked_tx for the TX itself
also rename the latter to csa_blocked_queues.
Fixes: 6f0107d195 ("wifi: mac80211: introduce a feature flag for quiet in CSA")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415112355.1d91db5e95aa.Iad3a5df3367f305dff48cd61776abfd6cf0fd4ab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The AP removal timer field need not be aligned, so the
code shouldn't access it directly, but use unaligned
loads. Use get_unaligned_le16(), which even is shorter
than the current code since it doesn't need a cast.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.356788ba0045.I2b3cdb3644e205d5bb10322c345c0499171cf5d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP removal timer is long, we don't really want to
remove the link immediately. However, we really should do
it _before_ the AP removes it (which happens at or after
count reaches 0), so subtract 1 from the countdown when
scheduling the timer. This causes the link removal work
to run just after the beacon with value 1 is received. If
the counter is already zero, do it immediately.
This fixes an issue where we do the removal too late and
receive a beacon from the AP that's no longer associated
with the MLD, but thus removed EHT and ML elements, and
then we disconnect instead from the whole MLD, since one
of the associated APs changed mode from EHT to HE.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.03ac4a09fa74.Ifb8c8d38e3402721a81ce5981568f47b5c5889cb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP mode ends up being determined less than the client mode,
there may be different reasons for this, e.g. AP misconfiguration.
If this happens in a way that causes e.g. EHT to be rejected, the
elements need to be re-parsed since we'll connect as HE, but not
reparsing means that we'll still think it's OK to use multi-link,
so we can connect in a non-sensical configuration of advertising
only HE on a secondary link. This normally won't happen for the
assoc link because that reuses the mode from authentication, and
if that's not EHT, multi-link association is rejected.
Fix this inconsistency by parsing the elements again if the mode
was different from the first parsing attempt. Print the message a
bit later to avoid printing "determined AP ... to be HE" twice in
cases where ieee80211_determine_ap_chan() returned a lesser mode,
rather than the regulatory downgrades below changing it.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.d1f25d92cfe7.Ia21eff6cdcae2f5aca13cf8e742a986af5e70f89@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing re-parsing in ieee80211_determine_chan_mode(),
the conn->mode is changed, and the whole point of doing
the parsing again was to parse as the downgraded mode.
However, that didn't actually work, because the setting
was copied before and never changed again. Fix that.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.5e0d1fcb5622.Ib0673e0bc90033fd6d387b6a5f107c040eb907cf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The vif's idle state doesn't automatically go to true when
any link removes the channel context, it's only idle when
_all_ links no longer have a channel context. Fix that.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.90df97557702.I05d2228ce85c203b9f2d6da8538cc16dce46752a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the origin of the packets (and their SA), 802.11 + mesh headers
could be filled in differently. In order to properly deal with that, add a
new field to the lookup key, indicating the type (local, proxied or
forwarded). This can fix spurious packet drop issues that depend on the order
in which nodes/hosts communicate with each other.
Fixes: d5edb9ae8d ("wifi: mac80211: mesh fast xmit support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240415121811.13391-1-nbd@nbd.name
[use sizeof_field() for key_len]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the flag IEEE80211_KEY_FLAG_GENERATE_MMIE to BIP-CMAC-256,
BIP-GMAC-128 and BIP-GMAC-256 for the same reason and in the same
way that the flag was added originally in commit a0b4496a43
("mac80211: add IEEE80211_KEY_FLAG_GENERATE_MMIE to ieee80211_key_flags").
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://msgid.link/20240326003036.15215-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Logic inside ieee80211_rx_mgmt_beacon accesses the
mgmt->u.beacon.timestamp field without first checking whether the beacon
received is non-S1G format.
Fix the problem by checking the beacon is non-S1G format to avoid access
of the mgmt->u.beacon.timestamp field.
Signed-off-by: Richard Kinder <richard.kinder@gmail.com>
Link: https://msgid.link/20240328005725.85355-1-richard.kinder@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi as we didn't consider it
as major enough to justify merging wireless tree to wireless-next. But
Stephen has an example merge resolution which should help with fixing
the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmYNIqIRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt8jAf9H+o91boD34/qVdI5LWEcFhVKEkHpNtwm
Y1sTKNBEtN1Gs2zcljjO6PqN9N4v2+lA42KSpzP5M42FfpI2aATI2v8jYsKTXOl2
YVwF+8pDiAsi0YtQTxIthygjzTpsePCfj8z0xJaKGm195T+fMm9UebYETrfxxOp/
z5StsJIPI0twgSLKKUWvLpX4ESt0l0HLJY1ok99sk4Cj36EKn6b9LbBinDKr6GcQ
mGNtPyq0j4l0kS5qae9BbXZUohO54o8wiFnApdwGfA7S/kLY7eUtwZy7T050b62P
zbNafwZbIjrH7dNcGfe6Fdr7PjQYFeI5Nh7dXxqM2LJOQsYXU/tcWQ==
=WrPE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.10
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi, Stephen has an example
merge resolution which should help with fixing the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
* tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (122 commits)
wifi: mt76: mt7915: workaround dubious x | !y warning
wifi: mwl8k: Avoid -Wflex-array-member-not-at-end warnings
wifi: ti: Avoid a hundred -Wflex-array-member-not-at-end warnings
wifi: iwlwifi: mvm: fix check in iwl_mvm_sta_fw_id_mask
net: rfkill: gpio: Convert to platform remove callback returning void
wifi: mac80211: use kvcalloc() for codel vars
wifi: iwlwifi: reconfigure TLC during HW restart
wifi: iwlwifi: mvm: don't change BA sessions during restart
wifi: iwlwifi: mvm: select STA mask only for active links
wifi: iwlwifi: mvm: set wider BW OFDMA ignore correctly
wifi: iwlwifi: Add support for LARI_CONFIG_CHANGE_CMD cmd v9
wifi: iwlwifi: mvm: Declare HE/EHT capabilities support for P2P interfaces
wifi: iwlwifi: mvm: Remove outdated comment
wifi: iwlwifi: add support for BZ_W
wifi: iwlwifi: Print a specific device name.
wifi: iwlwifi: remove wrong CRF_IDs
wifi: iwlwifi: remove devices that never came out
wifi: iwlwifi: mvm: mark EMLSR disabled in cleanup iterator
wifi: iwlwifi: mvm: fix active link counting during recovery
wifi: iwlwifi: mvm: assign link STA ID lookups during restart
...
====================
Link: https://lore.kernel.org/r/20240403093625.CF515C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of restart, we currently reactivate multi-link on
interfaces before reconfiguring keys etc. which means the
drivers need to handle this case differently. Enable more
links later to allow them to handle it the same way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320091155.d0f18a56335d.Ib3338d93872a4a568f38db0d02546534d3eff810@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we use a drop we not only save the extra call to
dev_kfree_skb(), but also have a better reason in
tracing, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320091155.34daf0a89eb4.I60e0639511f9de64e40e6105b640adf90f8f57f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the links won't actually change, nothing will happen.
This was previously done in the inner function (twice in
some cases), but we shouldn't bother the driver with it.
Clean that up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320091155.a8190a312a27.If4e6f5ce8228eda7afac0fc8c17dd731c5da9ed9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If scan request doesn't include a link ID to be used for TSF
reporting, don't select it as it might become inactive before
scan is actually started by the driver.
Instead, let the driver select one of the active links.
Fixes: cbde0b49f2 ("wifi: mac80211: Extend support for scanning while MLO connected")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320091155.a6b643a15755.Ic28ed9a611432387b7f85e9ca9a97a4ce34a6e0f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have 13 bits for the status_data, so restricting
type to 4 and subdata to 8 bits is confusing, even if
we don't need more bits now. Change subdata mask to
be 9 bits instead, just to make things match up.
If we actually need more types or more subdata bits
we can later also reshuffle the bits between these,
but we should probably keep them at 13 bits together.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320091155.28ac7b665039.I1abbb13e90f016cab552492e05f5cb5b52de6463@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing link switch with a disjoint set of links before
and after the switch, we end up removing all channel contexts,
adding new ones later. This looks like 'idle' to the code now,
and we enter idle which also includes flushing queues. But we
can't actually flush since we don't have a link active (bound
to a channel context), and entering idle just to leave it again
is also wrong.
Fix this by passing through an indication that we shouldn't do
any idle checks in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320091155.170328bac555.If4a522a9dd3133b91983854b909a4de13aa635da@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to activate a link that is currently inactive due to
a negotiated TTLM request, need to first tear down the negotiated
TTLM request.
Add support for sending TTLM teardown request and update the links
state accordingly.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.d480cbf46fcf.Idedad472469d2c27dd2a088cf80a13a1e1cf9b78@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no reason to check the request flags for each of the links, so
pull that out of the loop. Also, within the loop we can set the per-link
error everywhere.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.695faa9be279.I71b11a8d66a9cae4c27e242a47d1d92922609b03@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may not be capable of handling puncturing in 5 GHz
only (vs. the current flag that just removes puncturing support
completely). Add a flag to support such devices: check and then
downgrade the channel width if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.49759510da7d.I12c5a61f0be512e0c4e574c2f794ef4b37ecaf6b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update power_type in bss_conf based on Indoor AFC and LPI power types
received in HE 6 GHz operation element on assoc success.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.89c25dae34ff.Ifd8b2983f400623ac03dc032fc9a20025c9ca365@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current mac80211 won't parsing puncturing bitmap when process EHT
Operation element in 6 GHz band or Bandwidth Indication element. This
leads to puncturing bitmap cannot be updated in related situations, such
as connecting to an EHT AP in 6 GHz band.
So supplement parsing of puncturing bitmap for these elements.
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Link: https://msgid.link/20240312045947.576231-2-quic_kangyang@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix ieee80211_ttlm_set_links() to not set all active links,
but instead let the driver know that valid links status changed
and select the active links properly.
Fixes: 8f500fbc6c ("wifi: mac80211: process and save negotiated TID to Link mapping request")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.acddbbf39584.Ide858f95248fcb3e483c97fcaa14b0cd4e964b10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If prep_channel fails in prep_connection, the code releases
the deflink's chanctx, which is wrong since we may be using
a different link. It's already wrong to even do that always
though, since we might still have the station. Remove it
only if prep_channel succeeded and later updates fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.2780c1f08c3d.I033c9b15483933088f32a2c0789612a33dd33d82@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Running kernel-doc on ieee80211_i.h flagged the following:
net/mac80211/ieee80211_i.h:145: warning: expecting prototype for enum ieee80211_corrupt_data_flags. Prototype was for enum ieee80211_bss_corrupt_data_flags instead
net/mac80211/ieee80211_i.h:162: warning: expecting prototype for enum ieee80211_valid_data_flags. Prototype was for enum ieee80211_bss_valid_data_flags instead
Fix these warnings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/20240314-kdoc-ieee80211_i-v1-1-72b91b55b257@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When moving a station out of a VLAN and deleting the VLAN afterwards, the
fast_rx entry still holds a pointer to the VLAN's netdev, which can cause
use-after-free bugs. Fix this by immediately calling ieee80211_check_fast_rx
after the VLAN change.
Cc: stable@vger.kernel.org
Reported-by: ranygh@riseup.net
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240316074336.40442-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure that the new mlme_link_id_dbg() macro honours
CONFIG_MAC80211_MLME_DEBUG as intended to avoid spamming the log with
messages like:
wlan0: no EHT support, limiting to HE
wlan0: determined local STA to be HE, BW limited to 160 MHz
wlan0: determined AP xx:xx:xx:xx:xx:xx to be VHT
wlan0: connecting with VHT mode, max bandwidth 160 MHz
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/20240325085948.26203-1-johan+linaro@kernel.org
Tested-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fourth "new features" pull request for v6.9 with changes both in
stack and in drivers. The theme in this pull request is to fix sparse
warnings but we still have some left in wireless subsystem. Otherwise
quite normal.
Major changes:
rtw89
* NL80211_EXT_FEATURE_SCAN_RANDOM_SN support
* NL80211_EXT_FEATURE_SET_SCAN_DWELL support
rtw88
* support for more rtw8811cu and rtw8821cu devices
mt76
* mt76x2u: add Netgear WNDA3100v3 USB
* mt7915: newer ADIE version support
* mt7925: radio temperature sensor support
* mt7996: remove GCMP IGTK offload
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmXq4hARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtOawf9Gf2FAi56zA/4vKJPE/mZzRvNodj/u9WL
mEX3KERw744IEmWY0yXEAyvzKkkNqUUtmdUbbsnXnnEtzsVZ2oRmOZdXsvEW3vOD
IEsjWY/405MBWyuBttAa6orBSgelr99k86HzoLN86s52HmliVDhr2EUnYIf2O++9
SVhHFKE4BMVCO6hlyEg419K9M2VhWtBDNYweoXAfn8Y1byAw6Pt6WunjRuGwJG5n
qvcrZcFCFSa3daPpx0uIA/yiSjZlq0hwVC3r/PnoX/r1FDR8tS2ecvC2rP3MaZJ+
1x3IcNvwC97D80wvdW+f+qKtV4OXZefsZpzJJpvREH8FbAgYLDef0Q==
=gln7
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The fourth "new features" pull request for v6.9 with changes both in
stack and in drivers. The theme in this pull request is to fix sparse
warnings but we still have some left in wireless subsystem. Otherwise
quite normal.
Major changes:
rtw89
* NL80211_EXT_FEATURE_SCAN_RANDOM_SN support
* NL80211_EXT_FEATURE_SET_SCAN_DWELL support
rtw88
* support for more rtw8811cu and rtw8821cu devices
mt76
* mt76x2u: add Netgear WNDA3100v3 USB
* mt7915: newer ADIE version support
* mt7925: radio temperature sensor support
* mt7996: remove GCMP IGTK offload
* tag 'wireless-next-2024-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (125 commits)
wifi: rtw89: wow: move release offload packet earlier for WoWLAN mode
wifi: rtw89: wow: set security engine options for 802.11ax chips only
wifi: rtw89: update suspend/resume for different generation
wifi: rtw89: wow: update config mac function with different generation
wifi: rtw89: update DMA function with different generation
wifi: rtw89: wow: update WoWLAN status register for different generation
wifi: rtw89: wow: update WoWLAN reason register for different chips
wifi: brcm80211: handle pmk_op allocation failure
wifi: rtw89: coex: Add coexistence policy to decrease WiFi packet CRC-ERR
wifi: rtw89: coex: When Bluetooth not available don't set power/gain
wifi: rtw89: coex: add return value to ensure H2C command is success or not
wifi: rtw89: coex: Reorder H2C command index to align with firmware
wifi: rtw89: coex: add BTC ctrl_info version 7 and related logic
wifi: rtw89: coex: add init_info H2C command format version 7
wifi: rtw89: 8922a: add coexistence helpers of SW grant
wifi: rtw89: mac: add coexistence helpers {cfg/get}_plt
wifi: cw1200: restore endian swapping
wifi: wlcore: sdio: Rate limit wl12xx_sdio_raw_{read,write}() failures warns
wifi: rtlwifi: Remove rtl_intf_ops.read_efuse_byte
wifi: rtw88: 8821c: Fix false alarm count
...
====================
Link: https://lore.kernel.org/r/20240308100429.B8EA2C433F1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a link is deactivated, we really cannot sustain any
TDLS connections on that link any more. With the API
now changed, fix this issue and remove TDLS connections.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095719.a7dd812c37bf.I3474dbde79e9e7a539d47f6f81f32e6c3e459080@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a link does CSA, or if it changes SMPS mode, we need to
drop the TDLS peers, but we really should drop them only on
the affected link. Fix that.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095719.00d1d793f5b8.Ia9971316c6b3922dd371d64ac2198f91ed5ad9d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unify all the CSA handling, including handling of a beacon
after the CSA, into ieee80211_sta_process_chanswitch().
The CRC of the beacon will change due to changes in the
CSA/ECSA elements, so there's really no need to have the
'beacon after CSA' handling before the CRC processing or
to change the beacon_crc_valid value here.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.e269c0e02905.I9dc68ff1e84d51349822bc7d3b33b578fcf8e360@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing CSA in multi-link, there really isn't a need to
stop transmissions entirely. Add a feature flag for drivers
to indicate they can handle quiet in CSA (be it by parsing
themselves, or by implementing drv_pre_channel_switch()),
to make that possible.
Also clean up the csa_block_tx handling: it clearly cannot
handle multi-link due to the way queues are stopped, move
it to the sdata. Drivers should be doing it themselves for
working properly during CSA in MLO anyway. Also rename it
to indicate that it reflects TX was blocked at mac80211.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.258439191541.I2469d206e2bf5cb244cfde2b4bbc2ae6d1cd3dd9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link conf to the abort_channel_switch driver
method so the driver can handle things correctly.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095718.27f621106ddd.Iadd3d69b722ffe5934779a32a0e4e596a4e33ed4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For CSA to work correctly in multi-link scenarios, pass
the link_id to the relevant callbacks.
While at it, unify/deduplicate the tracing for them.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095718.b7726635c054.I0be5d00af4acb48cfbd23a9dbf067f9aeb66469d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're always using "scratch + len - pos", so we don't need
to subtract here to calculate the remaining length. Remove
the unnecessary subtraction.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240228094902.44e07cfa9e63.I7a9758fb9bc6b726aac49804f2f05cd521bc4128@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the scratch buffer (without advancing it) here in the
mlme.c code seems somewhat wrong, defragment the reconfig
multi-link element already when parsing. This might be a bit
more work in certain cases, but makes the whole thing more
regular.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094902.92936a3ce216.I4b736ce4fdc199fa1d6b00d00032f448c873a8b4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We shouldn't assign elems->ml_basic{,len} before defragmentation,
and we don't need elems->ml_reconf{,len} at all since we don't do
defragmentation. Clean that up a bit. This does require always
defragmention even when it may not be needed, but that's easier
to reason about.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094902.e0115da4d2a6.I89a80f7387eabef8df3955485d4a583ed024c5b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We sometimes need to check if a link is active, and this
is complicated by the fact that active_links has no bits
set when the vif isn't (acting as) an MLD. Add a small
new helper ieee80211_vif_link_active() to make that a bit
easier, and use it in a few places.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.688760aff5f7.I06892a503f5ecb9563fbd678d35d08daf7a044b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At this point, since it's taken from elems->ml_basic which
is stored only if it's of type basic, we don't really need
to check again if it's basic.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.ad1d4a09a6eb.Ib96fa75b1a6db21dd4182dcfa11fe9aff78fa3ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scratch_pos update here was lost after defrag, so any
other uses of the scratch buffer might overwrite it.
Fixes: a286de1aa3 ("wifi: mac80211: Rename multi_link")
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.9da35f39eeb7.I7127f2918ec4cba416fcbc35eacaea10262c1268@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The CQM handling did not consider the MLO case and thus notified
a not-existing link with the CQM change. To fix this, propagate
the CQM notification to all the active links (handling both the
non-MLO and MLO cases).
TODO: this currently propagates the same configuration to all
links regardless of the band. This might not be the correct
approach as different links might need to be configured with
different values.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094753.bf6a3fefe553.Id738810b73e1087e01d5885508b70a3631707627@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a beacon is received use it to update the BSS table regardless
of the scanning state. Do so only when there are active non-monitor
interfaces. Also, while at it, in any case accept beacons only with
broadcast address.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240228094742.e508605f495b.I3ab24ab3543319e31165111b28bcdcc622b5cf02@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, we need the link id in the GTK key to be given by
the driver after rekeying in wowlan, so add that.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094500.ce1bfc83a680.I43a6f8ab2804ee07116a37d5b9ec601b843464b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the association request, we make some parameters depend on the
AP's HT/VHT information. This was broken by my code because it no
longer filled that information, making it all zero.
For HT that meant we wouldn't reduce our capabilities to 20 MHz if
needed, and for VHT we lost beamforming capabilities.
Fix this. It seems like it may even have been broken for all but
the assoc link before.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094207.7dc812c2060a.Ibd591f9c214b4e166cf7171db3cf63bda8e3c9fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a link doesn't have VHT capability, before the rework
we'd have set IEEE80211_CONN_DISABLE_VHT, but now with the
linear progression of 'mode', we no longer have that. Add
an explicit check for VHT being supported, so we don't add
a zeroed VHT capabilities element where it shouldn't be.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094207.bfe4283bcde7.Ib70a558bc6bdbcec3d9e663079229dfcc2493682@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently whenever link AP is started, netif_carrier_up() function is
called and whenever it is brought down, netif_carrier_down() function is
called. However, with MLO, all the links of the same MLD would use the
same netdev. Hence there is no need to indicate for each link up/down.
Also, calling it down when only one of the links went down is not
desirable.
Add changes to call the netif_carrier_up() function only when first link
is brought up. Similarly, add changes to call the netif_carrier_down()
function only when last link is brought down.
In order to check the number of beaconing links in the given interface,
introduce a new helper function ieee80211_num_beaconing_links().
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240227042251.1511122-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently while stopping a link AP, all keys from the interface were
removed. However with MLO there is a requirement to free only the link
keys.
Add changes to remove keys which are associated with the link AP which is
going to be stopped.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240227042251.1511122-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently tracking rx_nss for each station, and that
is meant to be initialized to the capability NSS and later
reduced by the operating mode notification NSS.
However, we're mixing up capabilities and operating mode
NSS in the same variable. This forces us to recalculate
the NSS capability on operating mode notification RX,
which is a bit strange; due to the previous fix I had to
never keep rx_nss as zero, it also means that the capa is
never taken into account properly.
Fix all this by storing the capability value, that can be
recalculated unconditionally whenever needed, and storing
the operating mode notification NSS separately, taking it
into account when assigning the final rx_nss value.
Cc: stable@vger.kernel.org
Fixes: dd6c064cfc ("wifi: mac80211: set station RX-NSS on reconfig")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228120157.0e1c41924d1d.I0acaa234e0267227b7e3ef81a59117c8792116bc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station has not been uploaded yet, receiving SMPS or channel width
notification action frames can lead to rate_control_rate_update calling
drv_sta_rc_update with uninitialized driver private data.
Fix this by adding a missing check for sta->uploaded.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240221140535.16102-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the prototype of ieee80211_mle_get_bss_param_ch_cnt()
to also take a u8 * like the other functions, and make it
return -1 when the field isn't found, so that mac80211 can
check that instead of explicitly open-coding the check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240216135047.583309181bc3.Ia61cb0b4fc034d5ac8fcfaf6f6fb2e115fadafe7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The assignment to pointer cache in function mesh_fast_tx_gc can
be made at the declaration time rather than a later assignment.
There are also 3 functions where pointer cache is being initialized
at declaration time and later re-assigned again with the same
value, these are redundant and can be removed.
Cleans up code and three clang scan build warnings:
warning: Value stored to 'cache' during its initialization is never
read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/20240215232151.2075483-1-colin.i.king@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, function to check if beacon countdown is complete uses deflink
to fetch the beacon and check the counter. However, with MLO, there is
a need to check the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240216144621.514385-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a conflict already and some upcoming changes
also depend on changes in wireless for being conflict-
free, so pull wireless in to make all that easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver uses the new IEEE80211_CHAN_CAN_MONITOR, we
may monitor on channels that are, e.g. via regulatory,
otherwise considered disabled. However, we really shouldn't
transmit on them, so prevent that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206164849.9c03dcf67dbe.Ib86a851c274c440908c663f6dd774b79bfc3965d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, whenever AP link is brought down via ieee80211_stop_ap()
function, all stations connected to the sdata are flushed. However, in case
of MLO there is a requirement to flush only stations connected to that link
and not all.
For instance - Consider 2 GHz and 5 GHz are AP MLD. Now due to some reason
5 GHz link of this AP is going down (link removal or any other case). All
stations connected, even legacy stations connected to 2 GHz link AP would
also be flushed. Flushing of other link stations is not desirable.
Fix this issue by passing self link ID to sta_flush() function. This would
then only remove the stations which are still using the passed link
ID as their link sta. Other stations will not be affected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240205162952.1697646-4-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whenever sta_flush() function is invoked, all STAs present in that
interface are flushed. In case of MLO, it is desirable to only flush such
STAs that are at least using a given link id as one of their links.
Add support for this by making change in the __sta_info_flush API argument
to accept a link ID. And then, only if the STA is using the given link as
one of its links, it would be flushed.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240205162952.1697646-3-quic_adisi@quicinc.com
[reword commit message, in particular this isn't about "active" links]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get rid of gfp parameter from ieee80211_obss_color_collision_notify
since it is no longer used.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/f91e1c78896408ac556586ba8c99e4e389aeba02.1707389901.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a
finalizing worker using the deflink. With MLO, there is a need to do it
on a given link basis.
Pass link ID of the link on which CSA needs to be finalized.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add changes to start a channel switch as well as finalize it on link basis
in order to support CSA with MLO as well.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-5-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support CSA with MLO, there is a need to handle the functions
ieee80211_set_csa_beacon() and ieee80211_set_after_csa_beacon() on a per
link basis.
Implement this by making the function argument accept the the link data
instead of the sdata.
Currently, deflink would only be passed. Proper link data will be passed in
a subsequent patch.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-4-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, function to update beacon counter uses deflink to fetch
the beacon and then update the counter. However, with MLO, there is
a need to update the counter for the beacon in a particular link.
Add support to use link_id in order to fetch the beacon from a particular
link data during beacon update counter.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new Wi-Fi Standard (IEEE Std 802.11-2020 9.4.2.160) specifies that
the Wide Bandwidth Channel Switch (WBCS) Element subfields have the same
definitions as VHT operation information if the operating band is not
S1G.
The problem comes when the BSS is in 6 GHz band, the STA parses the WBCS
Element by ieee80211_chandef_vht_oper(), which checks the capabilities for
HT/VHT mode, not HE/EHT mode.
This patch refactors STA CSA parsing flow so that the corresponding
capabilities can be checked. Also, it adds the way to use op_class in ECSA
Element to build a new chandef.
In summary, the new steps for STA to handle CSA event are:
1. build the new chandef from one of the CSA-related (Sub)Elements in
following order,
- Bandwidth Indication (Sub)Element
- Wide Bandwidth Channel Switch (Sub)Element
- Operating class in Extended Channel Switch Announcement Element
- Channel Switch Announcement Element
2. convert the new chandef into operation information according to the
operating band in order to check if the new chandef fits STA's
capabilities.
3. downgrade the bandwidth until current bandwidth is not disabled.
Co-developed-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://msgid.link/20231222010914.6521-3-michael-cy.lee@mediatek.com
[rebase on top of the changes with struct ieee80211_conn_settings,
prefer leXY_encode_bits()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may (notably mt76 does) not set up sband->band
before registering, and cfg80211 will fill it in later. But
since the HT/HE capability check mac80211 required it to be
initialized already, otherwise failing things. This really
isn't necessary though since the code is iterating the list
of bands, and has the 'band' variable available. Fix it to
not require the sband->band to be initialized already.
Fixes: f04d2c247e ("wifi: mac80211: disallow drivers with HT wider than HE")
Reported-by: Bert Karwatzki <spasswolf@web.de>
Debugged-by: Bert Karwatzki <spasswolf@web.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218466
Link: https://msgid.link/20240207115920.43cbedffb5c3.I4968e12275a3f95926e3f3ccae81e50f23fe4d4d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The vif pointer at least looks like it can actually be NULL
in some cases such as the monitor-mode vif, causing static
checkers to complain with the immediate derefence. In these
cases the sta pointer will also be NULL, but clarify it in
the code anyway.
Link: https://msgid.link/20240131164910.60066625a239.Idfb6a5a9876f9f631eae760055e1c4018259a971@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The building of elements is really mess, and really the only
reason we're not doing it in SKBs in the first place is that
the scan code in ieee80211_build_preq_ies() doesn't.
Convert ieee80211_build_preq_ies() to use an SKB internally
so that we can gradually convert other things to ..._put_*()
style interfaces.
Link: https://msgid.link/20240129202041.c3a8e3c2cc99.I9d9920858c30ae5154719783933de0d7bc2a2cb9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If intending to associate with a lower bandwidth, remove capabilities
related to 320 MHz from the EHT capabilities element. Also change the
EHT MCS-NSS set accordingly: if just reducing 320->160 or similar the
format doesn't change, just cut off the last bytes. If changing from
higher bandwidth to 20 MHz only EHT STA, adjust the format.
Note that this also requires adjusting the caller in mlme.c since the
data written can now be shorter than it determined. We need to clean
all that up. Since the other callers pass NULL for the conn limit, we
don't need to change things there.
Link: https://msgid.link/20240129202041.b5f6df108c77.I0d8ea04079c61cb3744cc88625eeaf0d4776dc2b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aloka originally suggested that puncturing should be part of
the chandef, so that it's treated correctly. At the time, I
disagreed and it ended up not part of the chandef, but I've
now realized that this was wrong. Even for clients, the RX,
and perhaps more importantly, CCA configuration needs to take
puncturing into account.
Move puncturing into the chandef, and adjust all the code
accordingly. Also add a few tests for puncturing in chandef
compatibility checking.
Link: https://lore.kernel.org/linux-wireless/20220214223051.3610-1-quic_alokad@quicinc.com/
Suggested-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://msgid.link/20240129194108.307183a5d2e5.I4d7fe2f126b2366c1312010e2900dfb2abffa0f6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the earlier restructuring we now mostly ignore
the channel configuration in the association response,
apart from the HT/VHT checks we had.
Don't do that, but parse it and update, also dropping the
association if the AP changed its mode in the response.
Link: https://msgid.link/20240129194108.b3efa5eae60c.I1b70c9fd56781b22cdfdca55d34d69f7d0733e31@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
EHT requires that stations are able to participate in
wider bandwidth OFDMA, i.e. parse downlink OFDMA and
uplink OFDMA triggers when they're not capable of (or
not connected at) the (wider) bandwidth that the AP
is using. This requires hardware configuration, since
the entity responsible for parsing (possibly hardware)
needs to know the AP bandwidth.
To support this, change the channel request to have
the AP's bandwidth for clients, and track that in the
channel context in mac80211. This means that the same
chandef might need to be split up into two different
contexts, if the APs are different. Interfaces other
than client are not participating in OFDMA the same
way, so they don't request any AP setting.
Note that this doesn't introduce any API to split a
channel context, so that there are cases where this
might lead to a disconnect, e.g. if there are two
client interfaces using the same channel context, e.g.
both 160 MHz connected to different 320 MHz APs, and
one of the APs switches to 160 MHz.
Note also there are possible cases where this can be
optimised, e.g. when using the upper or lower 160 Mhz,
but I haven't been able to really fully understand the
spec and/or hardware limitations.
If, for some reason, there are no hardware limits on
this because the OFDMA (downlink/trigger) parsing is
done in firmware and can take the transmitter into
account, then drivers can set the new flag
IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW on interfaces to
not have them request any AP bandwidth in the channel
context and ignore this issue entirely. The bss_conf
still contains the AP configuration (if any, i.e. EHT)
in the chanreq.
Link: https://msgid.link/20240129194108.d3d5b35dd783.I939d04674f4ff06f39934b1591c8d36a30ce74c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the channel context code we have quite a few instances
of nested loops iterating the interfaces and then links.
Add a new for_each_sdata_link() macro and use it. Also,
since it's easier, convert all the loops and a few other
places away from RCU as we now hold the wiphy mutex
everywhere anyway.
This does cause a little bit more work (such as checking
interface types for each link of an interface rather than
not iterating links in some cases), but that's not a huge
issue and seems like an acceptable trade-off, readability
is important too.
Link: https://msgid.link/20240129194108.7240829bd96d.I5ccbb8dd019cbcb5326c85d76121359225d6541a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the code we currently check for support 80+80, 160
and 320 channel widths, but really the way this should
be (and is otherwise) handled is that we compute the
highest channel bandwidth given there, and then cut it
down to what we support. This is also needed for wider
bandwidth OFDMA support.
Change the code to remove this limitation and always
parse the highest possible channel width.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129194108.d06f85082e29.I47e68ed3d97b0a2f4ee61e5d8abfcefc8a5b9c08@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rewrite the station-side connection handling. The connection
flags (IEEE80211_DISABLE_*) are rather confusing, and they're
not always maintained well. Additionally, for wider-bandwidth
OFDMA support we need to know the precise bandwidth of the AP,
which is currently somewhat difficult.
Rewrite this to have a 'mode' (S1G/legacy/HT/...) and a limit
on the bandwidth. This is not entirely clean because some of
those modes aren't completely sequenced (as this assumes in
some places), e.g. VHT doesn't exist on 2.4 GHz, but HE does.
However, it still simplifies things and gives us a good idea
what we're operating as, so we can parse elements accordingly
etc.
This leaves a FIXME for puncturing, this is addressed in a
later patch.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129194108.9451722c0110.I3e61f4cfe9da89008e1854160093c76a1e69dc2a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most devices now do duration calculations, so we don't hit
this code at all any more. Clearly the approach of warning
at compile time here when new bands are added didn't work,
the new bands were just added with "TODO". Clean it up, it
won't matter for new bands since they'll just not have any
need to calculate durations in software.
While at it, also clean up and unify the code a bit.
Link: https://msgid.link/20240129194108.70a97bd69265.Icdd8b0ac60a382244466510090eb0f5868151f39@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not sure how this happened or how nothing complained, but
this variable already exists in the outer function scope
with the same value (and the SKB isn't changed either.)
Remove the extra one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This got unused when the tracing was converted to dynamic
strings, so the define can be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't make sense to return BSS change flags in an int, as
they're a bigger type. For this particular function it still
works OK, but clean it up to avoid future errors (or copying
this code in a broken way.)
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240129195739.e340a7d5e7c6.I1dfcca32d43dce903494a2c474844491682671b4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On the 6 GHz band, probe responses are sent as broadcast to
optimise medium usage. However, without OCE configuration
we weren't accepting them, which is wrong, even if wpa_s is
by default enabling OCE. Accept them without the OCE config
as well.
Link: https://msgid.link/20240129200907.5a89c2821897.I92e9dfa0f9b350bc7f37dd4bb38031d156d78d8a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bug in ieee80211_set_unsol_bcast_probe_resp(), it tries
to return BSS_CHANGED_UNSOL_BCAST_PROBE_RESP (which has the value
1<<31) in an int, which makes it negative and considered an error.
Fix this by passing the changed flags to set separately.
Fixes: 3b1c256eb4 ("wifi: mac80211: fixes in FILS discovery updates")
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240129195729.965b0740bf80.I6bc6f5236863f686c17d689be541b1dd2633c417@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver implements the change_interface() method, we switch
interface type without taking the interface down, but still will
recreate the debugfs for it since it's a new type. As such, we
should use the ieee80211_debugfs_recreate_netdev() function here
to also recreate the driver's files, if it is indeed from a type
change while up.
Link: https://msgid.link/20240129155402.7311a36ffeeb.I18df02bbeb685d4250911de5ffbaf090f60c3803@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mentioned in the previous commit, we pretty quickly found
that some APs have ECSA elements stuck in their probe response,
so using that to not attempt to connect while CSA is happening
we never connect to such an AP.
Improve this situation by checking more carefully and ignoring
the ECSA if cfg80211 has previously detected the ECSA element
being stuck in the probe response.
Additionally, allow connecting to an AP that's switching to a
channel it's already using, unless it's using quiet mode. In
this case, we may just have to adjust bandwidth later. If it's
actually switching channels, it's better not to try to connect
in the middle of that.
Reported-by: coldolt <andypalmadi@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/CAJvGw+DQhBk_mHXeu6RTOds5iramMW2FbMB01VbKRA4YbHHDTA@mail.gmail.com/
Fixes: c09c4f3199 ("wifi: mac80211: don't connect to an AP while it's in a CSA process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129131413.cc2d0a26226e.I682c016af76e35b6c47007db50e8554c5a426910@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the way that debugging is used in the mac80211 subsystem
this message ends up being noisier than it needs to be.
As the statement is only useful at a first stage of triage for
BIOS bugs, just drop it.
Cc: Jun Ma <Jun.Ma2@amd.com>
Suggested-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240117030525.539-1-mario.limonciello@amd.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch makes duration in scan request be applicable when using
SW scan, but only accepts durations greater than the default value for
the following reasons:
1. Most APs have a beacoon interval of 100ms.
2. Sending and receiving probe require some delay.
3. Setting channel to HW also requires some delays
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://msgid.link/20240123054752.22833-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This does not change anything effectively, but it is closer to what the
code is trying to achieve here. i.e. select the link data if it is an
MLD and fall back to using the deflink otherwise.
Fixes: 0f99f08783 ("wifi: mac80211: Print local link address during authentication")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.4c4b1c40eb3c.I2771621dee328c618536596b7e56232df42a79c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing 6 GHz operation, don't set the bss_conf
values. We only commit to that later in association,
so move the code there. Also clear it later.
While at it, handle IEEE80211_6GHZ_CTRL_REG_VLP_AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c2da4bc515e8.I219ca40e15c0fbaff0e7c3e83ca4b92ecbc1f8ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To simplify the code in the next patch, disallow drivers
supporting 40 MHz in HT but not HE, since we'd otherwise
have to track local maximum bandwidth per mode there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.da15fe3214d2.I4df51ad2f4c844615c168bf9bdb498925b3c77d4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For verifying the required HE capabilities are supported
locally, we access the HE capability element of the AP.
Simplify that access, we've already parsed and validated
it when parsing elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.2ef62b43caeb.I8baa604dd3f3399e08b86c99395a2c6a1185d35d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already parse all the BSS elements into elems, there's
really no need to separately find EHT/ML again. Remove the
extra code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c4a55da9f778.I112b1ef00904c4183ac7644800f8daa8a4449875@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only user of this function passes a lot of pointers
directly from the parsed elements, so it's simpler to
just pass the entire elements parsing struct. This also
shows that the ht_cap is actually unused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.f0653cd5e7dd.I8bd5ee848074029a9f0495c95e4339546ad8fe15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The association response is more likely to be correct
than a random scan result, which really also should be
correct, but we generally prefer to take data from the
association response, so do that here as well.
Also reset the data so it doesn't hang around from an
old connection to a non-MLO connection, drivers would
hopefully not look at it, but less surprise this way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.1d10f1d1dbab.I545e955675e2269a52496a22ae7822d95b40235e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If software crypto is used, simply add support for SPP A-MSDUs
(and use it whenever enabled as required by the cfg80211 API).
If hardware crypto is used, leave it up to the driver to set
the NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT flag and then check
sta->spp_amsdu or the IEEE80211_KEY_FLAG_SPP_AMSDU key flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.b8ada4514e2b.I1ac25d5f158165b5a88062a5a5e4c4fbeecf9a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update neg_ttlm and active_links according to the new mapping,
and send a negotiated TID-to-link map request with the new mapping.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.eeb385d771df.I2a5441c14421de884dbd93d1624ce7bb2c944833@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An MLD may send TID-to-Link mapping request frame to negotiate
TID to link mapping with a peer MLD.
Support handling negotiated TID-to-Link mapping request frame
by parsing the frame, asking the driver whether it supports the
received mapping or not, and sending a TID-to-Link mapping response
to the AP MLD.
Theoretically, links that became inactive due to the received TID-to-Link
mapping request, can be selected to be activated but this would require
tearing down the negotiated TID-to-Link mapping, which is still not
supported.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.0bc1a24fcc9d.Ie72e47dc6f8c77d4a2f0947b775ef6367fe0edac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWuipMRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt17wgAhrkxpwRpMuRrV6VxHl9m+NXk7is2vni2
JZbqlvMIw1Hm+40K9D0WgFdNZUeAtBcd567MAbiqdzqRNB9DtEvnsXIKlKINwxIA
QFskkXR1f0sj79Hz3q7iWQq+jxDvAU5tge/WU65Na7+224sdyzBg7DZab8/buOsm
1xdx69MtGNU+dm4+V1Xp8h9jB7WAjq7N+ZhC6YfH6QSCL7JSL9Co/NC098gBnAEx
cm59vPOxk8+QoHKDjjmClTIhxOEgR6pSM8T3Dne9OYO8ONhxqdVSgd0Br+mEZgQ4
r61i88zK6ZmVZYckk6fhuGCLiKC6CFwS0eCLDQnKK1ufyRxDi84Y/Q==
=Cwmf
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc2
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
* tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix race condition on enabling fast-xmit
wifi: iwlwifi: fix a memory corruption
wifi: mac80211: fix potential sta-link leak
wifi: cfg80211/mac80211: remove dependency on non-existing option
wifi: cfg80211: fix missing interfaces when dumping
wifi: ath11k: rely on mac80211 debugfs handling for vif
wifi: p54: fix GCC format truncation warning with wiphy->fw_version
====================
Link: https://lore.kernel.org/r/20240122153434.E0254C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240104181059.84032-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station is allocated, links are added but not
set to valid yet (e.g. during connection to an AP MLD),
we might remove the station without ever marking links
valid, and leak them. Fix that.
Fixes: cb71f1d136 ("wifi: mac80211: add sta link addition/removal")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.6573998beaf8.I09ac2e1d41c80f82a5a616b8bd1d9d8dd709a6a6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ffbd0c8c1e ("wifi: mac80211: add an element parsing unit test")
and commit 730eeb17bb ("wifi: cfg80211: add first kunit tests, for
element defrag") add new configs that depend on !KERNEL_6_2, but the config
option KERNEL_6_2 does not exist in the tree. This dependency is used for
handling backporting to restrict the option to certain kernels but this
really should not be carried around the mainline kernel tree.
Clean up this needless dependency on the non-existing option KERNEL_6_2.
Link: https://lore.kernel.org/lkml/CAKXUXMyfrM6amOR7Ysim3WNQ-Ckf9HJDqRhAoYmLXujo1UV+yA@mail.gmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- first kunit tests for both cfg80211 and mac80211
- a few multi-link fixes
- DSCP mapping update
- RCU fix
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEpeA8sTs3M8SN2hR410qiO8sPaAAFAmWVcYQACgkQ10qiO8sP
aABEdw//VOD/aR+ZXNwZBcRoJufHYCHu0h3gIKqEcB+W+e7dFs8OYQryHP/jo3AI
brOjcP9Upooyk6h7TNszL/YvjLjRmEFnaz3mEb41xy62M2NGHyPcA5lB9J5gphpY
uurhcj+SfxZeB0/YIVPR4Bwf/RTbDkWzJIWJ/f7mfXk2ELQby1ohzYCezK6p6f/p
vP7w0zk4xFFKZChbyrccBGHl5/Q6oOFOeuwXE4h0J1skBWUCfxjUInGiU7fuQEWb
FhJUzB1WSJPVKPzWuLC4bUvAcrwfv4JHCcjWECQyPr38+wrEj4DZle8XtLN/dEUB
aE/2wKyFcbHmGTqRiBuaPhms439WKbave1yDEdOmuvcgyj2AMNkY6hod9Q5bWZJr
L+MvJ50tTKJcUQNayA7pyGMdLr7lvMxkMsLPgPKGSLBMp/uqW/4SioXO4AqCfL7p
T3Vw9Z1SMFI5WvSSRssIL8Sbl0LS+vMGEN76HZmxs5m4d0f5Hv9RRFFDmNqFyD4G
iqKmYPi1XJc7QsoHtonyx+kByImFdl839RsU7WPh9GS045yNwlC3eWhZMgbuF/ol
1iWNPcXogh9ABh8zgFaeWrLnDj2Kcix6vtec//7YM5cTYklyr0Ruo3bwKR3N00C3
hNh5zVLd/LHoce6B0V5HAq+ajMnnGw6CT6pM7quF5srAJZLIKLM=
=dHxp
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Just a couple of more things over the holidays:
- first kunit tests for both cfg80211 and mac80211
- a few multi-link fixes
- DSCP mapping update
- RCU fix
* tag 'wireless-next-2024-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next:
wifi: mac80211: remove redundant ML element check
wifi: cfg80211: parse all ML elements in an ML probe response
wifi: cfg80211: correct comment about MLD ID
wifi: cfg80211: Update the default DSCP-to-UP mapping
wifi: cfg80211: tests: add some scanning related tests
wifi: mac80211: kunit: extend MFP tests
wifi: mac80211: kunit: generalize public action test
wifi: mac80211: add kunit tests for public action handling
kunit: add a convenience allocation wrapper for SKBs
kunit: add parameter generation macro using description from array
wifi: mac80211: fix spelling typo in comment
wifi: cfg80211: fix RCU dereference in __cfg80211_bss_update
====================
Link: https://lore.kernel.org/r/20240103144423.52269-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If "ml_basic" is assigned, we already know that the type
of ML element is basic, so we don't need to check again,
that check can never happen. Simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.bb9b636e66f6.I7fc0897022142d46f39ac0b912a4f7b0f1b6ea26@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the MFP tests to handle the case of deauth/disassoc
and robust action frames (that are not protected dual of
public action frames).
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20231220151952.415232-6-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generalize the test to be able to handle arbitrary
action categories and non-action frames, for further
test expansion.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20231220151952.415232-5-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the logic in ieee80211_drop_unencrypted_mgmt()
according to a list of test cases derived from the
spec.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://msgid.link/20231220151952.415232-4-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix spelling of "attributes" in a comment.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Zheng tan <tanzheng@kylinos.cn>
Link: https://msgid.link/20240102015418.3673858-1-tanzheng@kylinos.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The third "new features" pull request for v6.8. This is a smaller one
to clear up our tree before the break and nothing really noteworthy
this time.
Major changes:
stack
* cfg80211: introduce cfg80211_ssid_eq() for SSID matching
* cfg80211: support P2P operation on DFS channels
* mac80211: allow 64-bit radiotap timestamps
iwlwifi
* AX210: allow concurrent P2P operation on DFS channels
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWFbnIRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZs5hQf/aCvvTjqeRoMkmO+ZPFMSO+YquZNCJi1M
TP8Fce2ALKj7woPad8vdJNNStMa9k4bu2NvShMXhoYM3xOA/4o0P9yeb5OfyYkTk
Y6JF+SoBGzABtB3m/a3i5J19F+oC+6yKN6/OY8byfK4jqZdrAprc3qXwodC5zb9n
blC16KKlldjoj5AWe/b6Vn/LI9P7mVhZIaWxI9IaktK0eIgfsfcgIZLuuMJPq5DJ
NjvhmK++qCcTQrJo/4TMVoWmcZZKR3XzcSs++HYRELNCwcM2q9s07R4KkV81aB0t
RpCaCWa2KVUCrKdk3FlnG5pS7A6US5KGP4g6sSQRnq8t3IYDUbDo5Q==
=Bte8
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The third "new features" pull request for v6.8. This is a smaller one
to clear up our tree before the break and nothing really noteworthy
this time.
Major changes:
stack
* cfg80211: introduce cfg80211_ssid_eq() for SSID matching
* cfg80211: support P2P operation on DFS channels
* mac80211: allow 64-bit radiotap timestamps
iwlwifi
* AX210: allow concurrent P2P operation on DFS channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During ieee80211_set_active_links() we do (among the others):
1. Call drv_change_vif_links() with both old_active and new_active
2. Unassign the chanctx for the removed link(s) (if any)
3. Assign chanctx to the added link(s) (if any)
4. Call drv_change_vif_links() with the new_active links bitmap
The problem here is that during step #1 the driver doesn't know whether
we will activate multiple links simultaneously or are just doing a link
switch, so it can't check there if multiple links are supported/enabled.
(Some of the drivers might enable/disable this option dynamically)
And during step #3, in which the driver already knows that,
returning an error code (for example when multiple links are not
supported or disabled), will cause a warning, and we will still complete
the transition to the new_active links.
(It is hard to undo things in that stage, since we released channels etc.)
Therefore add a driver callback to check if the desired new_active links
will be supported by the driver or not. This callback will be called
in the beginning of ieee80211_set_active_links() so we won't do anything
before we are sure it is supported.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20231220133549.64c4d70b33b8.I79708619be76b8ecd4ef3975205b8f903e24a2cd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Handle a case of time overflow, where the switch time might
be smaller than the partial TSF in the beacon.
Additionally, apply advertised TTLM earlier in order to be
ready on time on the newly activated links.
Fixes: 702e80470a ("wifi: mac80211: support handling of advertised TID-to-link mapping")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.15079c34e5c8.I0dd50bcceff5953080cdd7aee5118b72c78c6507@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting the radiotap timestamp, the mactime field is
usually unused, we take the data from the device_timestamp.
However, there can be cases where the radiotap timestamp is
better reported as a 64-bit value, so since the mactime is
free, add a flag to support using the mactime as a 64-bit
radiotap timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.00c8b9234f0c.Ie3ce5eae33cce88fa01178e7aea94661ded1ac24@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We only have a single flag free, and before using that for
another mactime flag, instead refactor the mactime flags
to use a 2-bit field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.d0e664832d14.I20c8900106f9bf81316bed778b1e3ce145785274@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may support concurrent DFS operation which relies on the
BSS channel width for its relaxations. Notify cfg80211 about BW change
so it can schedule regulatory checks.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.e08f8e9ebc67.If8915d13e203ebd380579f55fd9148e9b3f43306@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible for the TX status report for the (Re)Association Request
frame to be delayed long enough for the AP's (Re)Association Response
frame to be received and processed before it. If that were to happen for
a case where the AP rejects the association with indication to come back
later, the association timeout and retry state should not be modified
anymore with the TX status information that would be processed after
this. Updating the association timeout in such a reverse order of events
could result in shortening the timeouts for the association comeback
mechanism and that could result in the association failing.
Track whether we have already processed association rejection with
comeback time and if so, skip the timeout and retry update on any
following TX status report.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Link: https://msgid.link/20231219174814.2581575-1-j@w1.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface is removed, we should also be deleting the driver
debugfs entries (as it might still exist in DOWN state in mac80211). At
the same time, when adding an interface, we can check the
IEEE80211_SDATA_IN_DRIVER flag to know whether the interface was
previously known to the driver and is simply being reconfigured.
Fixes: a1f5dcb1c0 ("wifi: mac80211: add a driver callback to add vif debugfs")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220043149.a9f64c359424.I7076526b5297ae8f832228079c999f7b8e147a4c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver debugfs entries still exist when the interface is re-added
during reconfiguration. This can be either because of a HW restart
(in_reconfig) or because we are resuming.
Fixes: a1f5dcb1c0 ("wifi: mac80211: add a driver callback to add vif debugfs")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220043149.ddd48c66ec6b.Ia81080d92129ceecf462eceb4966bab80df12060@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWAdRERHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu0RAf+JtHgfjmUMFb54xcncLgj8ZAN82E0ThE0
bPewQDhot0QTri4s7i5Kn8PCWjk+eKEmiIK+eARM+JDyZMTlCpXs2Y92cDAGQ8KG
+LbIMRQkwOUg0HmtX3NysUG3mGAx4QTcIX/y3+GmtMZpKXMFuNy6ODuFvuWFNJrF
3XTq1qFQNnA0XqUDKHW9uareeCiOMVOsqcxNW2FAi2gqRUfQpKnU1Ukv5iOjkqE9
i53GHzeAG2WI4/YjXaTEZvibkM3jqrPcquHlul3fVuq05qkKOEuiy2UalDjgDCYp
u91vbmMpcOjhlf9GIiu2BF6K/muEUCCIjlh5oxob0k9NiKhnPUZLng==
=6Y8M
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
* tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (207 commits)
wifi: mt76: mt7996: Use DECLARE_FLEX_ARRAY() and fix -Warray-bounds warnings
wifi: ath11k: workaround too long expansion sparse warnings
Revert "wifi: ath12k: use ATH12K_PCI_IRQ_DP_OFFSET for DP IRQ"
wifi: rt2x00: remove useless code in rt2x00queue_create_tx_descriptor()
wifi: rtw89: only reset BB/RF for existing WiFi 6 chips while starting up
wifi: rtw89: add DBCC H2C to notify firmware the status
wifi: rtw89: mac: add suffix _ax to MAC functions
wifi: rtw89: mac: add flags to check if CMAC and DMAC are enabled
wifi: rtw89: 8922a: add power on/off functions
wifi: rtw89: add XTAL SI for WiFi 7 chips
wifi: rtw89: phy: print out RFK log with formatted string
wifi: rtw89: parse and print out RFK log from C2H events
wifi: rtw89: add C2H event handlers of RFK log and report
wifi: rtw89: load RFK log format string from firmware file
wifi: rtw89: fw: add version field to BB MCU firmware element
wifi: rtw89: fw: load TX power track tables from fw_element
wifi: mwifiex: configure BSSID consistently when starting AP
wifi: mwifiex: add extra delay for firmware ready
wifi: mac80211: sta_info.c: fix sentence grammar
wifi: mac80211: rx.c: fix sentence grammar
...
====================
Link: https://lore.kernel.org/r/20231218163900.C031DC433C9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct run-on sentences by changing "," to ";".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Link: https://msgid.link/20231213054809.23475-1-rdunlap@infradead.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correct a run-on sentence by changing "," to ";".
Add a subject in one sentence.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Link: https://msgid.link/20231213054800.22561-1-rdunlap@infradead.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ESS capability bit is reserved in frames transmitted by
the client, so we shouldn't set it. Since we've set it for
decades, keep that old behaviour unless we're connection to
a new EHT AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.65005aba900b.I3d00c8741400572a89a7508b5ae612c968874ad7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ENOTSUP isn't a standard error code. EOPNOTSUPP should be used instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.3841b71c867d.Idf2ad01d9dfe8d6d6c352bf02deb06e49701ad1d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There may be cases where puncturing isn't possible, and
a connection needs to be downgraded. Add a hardware flag
to support this.
This is likely temporary: it seems we will need to move
puncturing to the chandef/channel context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.c1e89ea55e93.I37b8ca0ee64d5d7699e351785a9010afc106da3c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prefer native jiffies-wide 'unsigned long' for the 'last_active' field of
'struct airtime_info' and introduce 'ieee80211_sta_keep_active()' for airtime
check in 'ieee80211_txq_keep_active()' and 'ieee80211_sta_register_airtime()'.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://msgid.link/20231206060935.612241-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support the WBRF mechanism, Wifi adapters utilized in the system must
register the frequencies in use (or unregister those frequencies no longer
used) via the dedicated calls. So that, other drivers responding to the
frequencies can take proper actions to mitigate possible interference.
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Co-developed-by: Evan Quan <quanliangl@hotmail.com>
Signed-off-by: Evan Quan <quanliangl@hotmail.com>
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Link: https://msgid.link/20231211100630.2170152-5-Jun.Ma2@amd.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee802_11_parse_elems() can return NULL, so we must
check for the return value.
Fixes: 5d24828d05 ("mac80211: always allocate struct ieee802_11_elems")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.93dea364f3d3.Ie87781c6c48979fb25a744b90af4a33dc2d83a28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to check that cfg80211_defragment_element()
didn't return an error, since it can fail due to bad
input, and we didn't catch that before.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.8595a6b67fc0.I1225edd8f98355e007f96502e358e476c7971d8c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we're doing reconfig, then we cannot add the debugfs
files that are already there from before the reconfig.
Skip that in drv_change_sta_links() during reconfig.
Fixes: d2caad527c ("wifi: mac80211: add API to show the link STAs in debugfs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.88a950f43e16.Id71181780994649219685887c0fcad33d387cc78@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The debugfs files for netdevs (sdata) and links are removed
with the wiphy mutex held, which may deadlock. Use the new
wiphy locked debugfs to avoid that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The read is currently with RCU and the write can deadlock,
convert both for the sake of illustration.
Make mac80211 depend on cfg80211 debugfs to get the helpers,
but mac80211 debugfs without it does nothing anyway. This
also required some adjustments in ath9k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- If the scan request includes a link ID, validate that it is
one of the active links. Otherwise, if the scan request doesn't
include a valid link ID, select one of the active links.
- When reporting the TSF for a BSS entry, use the link ID information
from the Rx status or the scan request to set the parent BSSID.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231113112844.68564692c404.Iae9605cbb7f9d52e00ce98260b3559a34cf18341@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new 320 MHz channel width wasn't handled, so connecting
a station to a 320 MHz AP would limit the station to 20 MHz
(on HT) after a warning, handle 320 MHz to fix that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20231109182201.495381-1-greearb@candelatech.com
[write a proper commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Closes: https://github.com/openwrt/openwrt/issues/12420
Fixes: 0b75a1b1e4 ("wifi: mac80211: flush queues on STA removal")
Fixes: d00800a289 ("wifi: mac80211: add flush_sta method")
Tested-by: Konstantin Demin <rockdrilla@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Link: https://lore.kernel.org/r/20231104141333.3710-1-oldium.pro@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The third, and most likely the last, features pull request for v6.7.
Fixes all over and only few small new features.
Major changes:
iwlwifi
* more Multi-Link Operation (MLO) work
ath12k
* QCN9274: mesh support
ath11k
* firmware-2.bin container file format support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmU6KqgRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZtyMwf7B/BqV0LCNzBxtrWl3WYtgQgULgWFmEJt
83/Vo8pXelZzzMMERwvZtPCwEUm/L/vOO/a/k0oSz/XQbt4PTIBGnWA7JwYZGY++
1Kc79oMyXxG4Q4RCnKG/qQMzCnyL54RHUfFQrNaa3Bkgp7vGobU+ixH4NaqHI3M9
OFmyhCklk9AO0VTtT6vQQBM6wM3UC1adneZMVlb8xD2Wi5rkrRk4PX5msgaYrStR
ketZE6IPnnX8DziqGZPlTz1SSuOSnwGTOramdeGLKIUUlZbPWHTSBZ8lh/xnvGUB
561mp3/iguFtq2NvduPBqItotBzLGvnJZbLDrBPxB/v99q+7/cziSA==
=Xf7b
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.7
The third, and most likely the last, features pull request for v6.7.
Fixes all over and only few small new features.
Major changes:
iwlwifi
- more Multi-Link Operation (MLO) work
ath12k
- QCN9274: mesh support
ath11k
- firmware-2.bin container file format support
* tag 'wireless-next-2023-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (155 commits)
wifi: ray_cs: Remove unnecessary (void*) conversions
Revert "wifi: ath11k: call ath11k_mac_fils_discovery() without condition"
wifi: ath12k: Introduce and use ath12k_sta_to_arsta()
wifi: ath12k: fix htt mlo-offset event locking
wifi: ath12k: fix dfs-radar and temperature event locking
wifi: ath11k: fix gtk offload status event locking
wifi: ath11k: fix htt pktlog locking
wifi: ath11k: fix dfs radar event locking
wifi: ath11k: fix temperature event locking
wifi: ath12k: rename the sc naming convention to ab
wifi: ath12k: rename the wmi_sc naming convention to wmi_ab
wifi: ath11k: add firmware-2.bin support
wifi: ath11k: qmi: refactor ath11k_qmi_m3_load()
wifi: rtw89: cleanup firmware elements parsing
wifi: rt2x00: rework MT7620 PA/LNA RF calibration
wifi: rt2x00: rework MT7620 channel config function
wifi: rt2x00: improve MT7620 register initialization
MAINTAINERS: wifi: rt2x00: drop Helmut Schaa
wifi: wlcore: main: replace deprecated strncpy with strscpy
wifi: wlcore: boot: replace deprecated strncpy with strscpy
...
====================
Link: https://lore.kernel.org/r/20231026090411.B2426C433CB@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Not all public action frames have a protected variant. When MFP is
enabled drop only public action frames that have a dual protected
variant.
Fixes: 76a3059cf1 ("wifi: mac80211: drop some unprotected action frames")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231016145213.2973e3c8d3bb.I6198b8d3b04cf4a97b06660d346caec3032f232a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To be able to more easily understand the code, drop robust
action frames before being associated, even if there's no
MFP in the end, as they are Class 3 Frames and shouldn't
be transmitted in the first place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231001125722.b2fd37083371.Ie9f4906e2f6c698989bce6681956ed2f9454f27c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to overlapping changes and merges, another error
path ended up broken. Fix this one as well.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
make htmldocs warns:
Documentation/driver-api/80211/cfg80211:48: ./include/net/cfg80211.h:7290: WARNING: Duplicate C declaration, also defined at cfg80211:7251.
Declaration is '.. c:function:: void cfg80211_rx_assoc_resp (struct net_device *dev, struct cfg80211_rx_assoc_resp *data)'.
This is because there's a function named cfg80211_rx_assoc_resp() and a struct
named cfg80211_rx_assoc_resp, see previous patch for more info.
To workaround this rename the struct to cfg80211_rx_assoc_resp_data. The
parameter for the function is named 'data' anyway so the naming here is
consistent.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231012114229.2931808-3-kvalo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
make htmldocs warns:
Documentation/driver-api/80211/mac80211:109: ./include/net/mac80211.h:5170: WARNING: Duplicate C declaration, also defined at mac80211:1117.
Declaration is '.. c:function:: void ieee80211_tx_status (struct ieee80211_hw *hw, struct sk_buff *skb)'.
This is because there's a function named ieee80211_tx_status() and a struct named
ieee80211_tx_status. This has been discussed previously but no solution found:
https://lore.kernel.org/all/20220521114629.6ee9fc06@coco.lan/
There's also a bug open for three years with no solution in sight:
https://github.com/sphinx-doc/sphinx/pull/8313
So I guess we have no other solution than to a workaround this in the code,
for example to rename the function to ieee80211_tx_status_skb() to avoid the
name conflict. I got the idea for the name from ieee80211_tx_status_noskb() in
which the skb is not provided as an argument, instead with
ieee80211_tx_status_skb() the skb is provided.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231012114229.2931808-2-kvalo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using e.g. bonding, and doing a sequence such as
# iw wlan0 set type __ap
# ip link add name bond1 type bond
# ip link set wlan0 master bond1
# iw wlan0 interface del
we deadlock, since the wlan0 interface removal will cause
bonding to reset the MAC address of wlan0.
The locking would be somewhat difficult to fix, but since
this only happens during removal, we can simply ignore the
MAC address change at this time.
Reported-by: syzbot+25b3a0b24216651bc2af@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20231012123447.9f9d7fd1f237.Ic3a5ef4391b670941a69cec5592aefc79d9c2890@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
While there, use struct_size() helper, instead of the open-coded
version, to calculate the size for the allocation of the whole
flexible structure including, of course, the flexible-array member.
This code was found with the help of Coccinelle, and audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/ZSQ/jcmTAf/PKHg/@work
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we are moving to MLO and links terms, also the airtime protection
will be done for a link rather than for a vif. Thus, some
drivers will need to know for which link to protect airtime.
Add link id as a parameter to the mgd_prepare_tx() callback.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.c7fc59a6780b.Ic88a5037d31e184a2dce0b031ece1a0a93a3a9da@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there is a disassoc before the fisrt beacon we need to protect a
session for the deauth frame. Currently we are checking if we had a
beacon in the default link, which is wrong in a MLO connection and
link id != 0.
Fix this by checking all the active links, if none had a beacon then
protect a session.
If at least one link had a beacon there is no need for session
protection.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004120820.d290f0ab77b0.Ic1505cf3d60f74580d31efa7e52046947c490b85@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the station is marked as no longer authorized, we shouldn't
transmit to it any longer, but in particular we shouldn't be able
to transmit to it after removing keys, which might lead to frames
being sent out unencrypted depending on the exact hardware offload
mechanism. Thus, instead of flushing only on station destruction,
which covers only some cases, always flush on unauthorization.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.d47f528829e7.I96903652c7ee0c5c66891f8b2364383da8e45a1f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When this flow is invoked with the "drop" parameter as true,
we only drop the frames from the hw queues, but not from the
sw queues.
So when we call wake_queues() after hw queue purging, all the
frames from the sw queues will be TX'ed,
when what we actually want to do is to purge all queues
in order to not TX anything...
This can cause, for example, TXing data frames to the peer
after the deauth frame was sent.
Fix this by purging the sw queues in addition to the hw queues
if the drop parameter is true.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.8fc2ee23e56f.I8b3f6def9c28ea96261e2d31df8786986fb5385b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the remain on channel is removed at the time it should
have expired, we have a race: the driver could be handling
the flow of the expiration while mac80211 is cancelling
that very same remain on channel request.
This wouldn't be problem in itself, but since mac80211
can send the next request to the driver in the cancellation
flow, we can get to the following situation:
CPU0 CPU1
expiration of roc in driver
ieee80211_remain_on_channel_expired()
Cancellation of the roc
schedules a worker (hw_roc_done)
Add next roc
hw_roc_done_wk runs and ends
the second roc prematurely.
Since, by design, there is only one single request sent to the
driver at a time, we can safely assume that after the cancel()
request returns from the driver, we should not handle any worker
that handles the expiration of the request.
Cancel the hw_roc_done worker after the cancellation to make
sure we start the next one with a clean slate.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.4e4469be20ac.Iab0525f5cc4698acf23eab98b8b1eec02099cde0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since userspace can choose now what link to establish the
TDLS on, we should know on what channel to do session protection.
Add a link id parameter to this callback.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.ef12ce3eb835.If864f406cfd9e24f36a2b88fd13a37328633fcf9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When setting the interface links, ignore the change iff both the
valid links and the dormant links did not change. This is needed
to support cases where the valid links didn't change but the dormant
links did.
Fixes: 6d543b34db ("wifi: mac80211: Support disabled links during association")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.0357b6306587.I7dbfec347949b629fea680d246a650d6207ff217@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
EMLSR operation and SMPS operation cannot coexist. Thus, when EMLSR is
enabled, all SMPS signaling towards the AP should be stopped (it is
expected that the AP will consider SMPS to be off).
Rename IEEE80211_VIF_DISABLE_SMPS_OVERRIDE to IEEE80211_VIF_EML_ACTIVE
and use the flag as an indication from the driver that EMLSR is enabled.
When EMLSR is enabled SMPS flows towards the AP MLD should be stopped.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.fb2c2f9a0645.If6df5357568abd623a081f0f33b07e63fb8bba99@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, we have a per-link debugfs directory which contains the
per-link files. In case of non-MLO we would like to put the per-link
files in the netdev directory to keep it how it was before MLO.
- Upon interface creation the netdev will be created with the per-link
files in it.
- Upon switching to MLO: delete the entire netdev directory and then
recreate it without the per-link files. Then the per-link directories
with the per-link files in it will be created in ieee80211_link_init()
- Upon switching to non-MLO: delete the entire netdev directory
(including the per-link directories) and recreate it with the per-link
files in it.
Note that this also aligns to always call the vif link debugfs
method for the deflink as promised in the documentation, which
wasn't done before.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.082e698caca9.I5bef7b2026e0f58b4a958b3d1f459ac5baeccfc9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a callback which the driver can use to add the vif debugfs.
We used to have this back until commit d260ff12e7 ("mac80211:
remove vif debugfs driver callbacks") where we thought that it
will be easier to just add them during interface add/remove.
However, now with multi-link, we want to have proper debugfs
for drivers for multi-link where some files might be in the
netdev for non-MLO connections, and in the links for MLO ones,
so we need to do some reconstruction when switching the mode.
Moving to this new call enables that and MLO drivers will have
to use it for proper debugfs operation.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.ac38913f6ab7.Iee731d746bb08fcc628fa776f337016a12dc62ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
