We'll use this function in bcm_config_lre_aneg(), therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/02bd7c39-7413-4433-bafc-a276089bd292@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genphy_c45_write_eee_adv() isn't used outside phy-c45.c,
so make it static.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/d23bd784-44e6-4a15-af3a-b37379156521@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we remove modes from EEE advertisement and disable / re-enable EEE,
then advertisement is set to all supported modes. I don't think this is
what the user expects. So respect the cached advertisement and just fall
back to all supported modes if cached advertisement is empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c75f7f8b-5571-429f-abd3-ce682d178a4b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MAC driver changes its EEE hardware configuration in its
adjust_link callback. This is called when auto-neg
completes. Disabling EEE via eee_enabled false will trigger an
autoneg, and as a result the adjust_link callback will be called with
phydev->enable_tx_lpi set to false. Similarly, eee_enabled set to true
and with a change of advertised link modes will result in a new
autoneg, and a call the adjust_link call.
If set_eee is called with only a change to tx_lpi_enabled which does
not trigger an auto-neg, it is necessary to call the adjust_link
callback so that the MAC is reconfigured to take this change into
account.
When setting phydev->enable_tx_lpi, take both eee_enabled and
tx_lpi_enabled into account, so the MAC drivers just needs to act on
phydev->enable_tx_lpi and not the whole EEE configuration.
The same check should be done for tx_lpi_timer too.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240302195306.3207716-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplify the function, no functional change intended.
- Remove not needed variable unsupp, I think code is even better
readable now.
- Move setting phydev->eee_enabled out of the if clause
- Simplify return value handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/442277c7-7431-4542-80b5-1d3d691714d7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Set 100BT1 and 1000BT1 linkmode advertisement bits to adv_l_mask to
enable detection.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-4-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for handling the EEE advertisement 2 register.
For now only 2500baseT and 5000baseT modes are supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading EEE link partner ability 2 register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use genphy_c45_read_eee_cap2(), complementing
genphy_c45_read_eee_cap1().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change genphy_c45_ethtool_[get|set]_eee to use EEE linkmode bitmaps.
This is a prerequisite for adding support for EEE modes beyond bit 31.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move part of the genphy_c45_pma_read_abilities() code to a separate
function.
Some PHYs do not implement PMA/PMD status 2 register (Register 1.8) but
do implement PMA/PMD extended ability register (Register 1.11). To make
use of it, we need to be able to access this part of code separately.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231212054144.87527-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Read the ability to do 100BASE-T1 and 1000BASE-T1 from the extended
BASE-T1 ability register of the PHY.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a separate function to read the BASE-T1 abilities. Some PHYs do not
indicate the availability of the extended BASE-T1 ability register, so
this function must be called separately.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to force 1000BASE-T1 by setting the correct control bit in
the MDIO_MMD_PMA_PMD_BT1_CTRL register.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The text has been cut/paste from genphy_c45_ethtool_get_eee but not
changed to reflect it performs set.
Additionally, extend the comment. This function implements the logic
that eee_enabled has global control over EEE. When eee_enabled is
false, no link modes will be advertised, and as a result, the MAC
should not transmit LPI.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230619220332.4038924-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, it is possible to let some PHYs to advertise not supported
EEE link modes. So, validate them before overwriting existing
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With following patches:
commit 9b01c885be ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
commit 5827b16812 ("net: phy: c45: migrate to genphy_c45_write_eee_adv()")
we set the advertisement to potentially supported values. This behavior
may introduce new regressions on systems where EEE was disabled by
default (BIOS or boot loader configuration or by other ways.)
At same time, with this patches, we would overwrite EEE advertisement
configuration made over ethtool.
To avoid this issues, we need to cache initial and ethtool advertisement
configuration and store it for later use.
Fixes: 9b01c885be ("net: phy: c22: migrate to genphy_c45_write_eee_adv()")
Fixes: 5827b16812 ("net: phy: c45: migrate to genphy_c45_write_eee_adv()")
Fixes: 022c3f87f8 ("net: phy: add genphy_c45_ethtool_get/set_eee() support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add new genphy_c45_an_config_eee_aneg() function and replace some of
genphy_c45_write_eee_adv() calls. This will be needed by the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make sure we use proper variable to validate access to potentially not
supported registers. Otherwise we will get false read/write errors.
Reported-by: kernel test robot <yujie.liu@intel.com>
Link: https://lore.kernel.org/oe-lkp/202302211644.c12d19de-yujie.liu@intel.com
Fixes: 022c3f87f8 ("net: phy: add genphy_c45_ethtool_get/set_eee() support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Migrate from genphy_config_eee_advert() to genphy_c45_write_eee_adv().
It should work as before except write operation to the EEE adv registers
will be done only if some EEE abilities was detected.
If some driver will have a regression, related driver should provide own
.get_features callback. See micrel.c:ksz9477_get_features() as example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add replacement for phy_ethtool_get/set_eee() functions.
Current phy_ethtool_get/set_eee() implementation is great and it is
possible to make it even better:
- this functionality is for devices implementing parts of IEEE 802.3
specification beyond Clause 22. The better place for this code is
phy-c45.c
- currently it is able to do read/write operations on PHYs with
different abilities to not existing registers. It is better to
use stored supported_eee abilities to avoid false read/write
operations.
- the eee_active detection will provide wrong results on not supported
link modes. It is better to validate speed/duplex properties against
supported EEE link modes.
- it is able to support only limited amount of link modes. We have more
EEE link modes...
By refactoring this code I address most of this point except of the last
one. Adding additional EEE link modes will need more work.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic function for EEE abilities defined by IEEE 802.3
specification. For now following registers are supported:
- IEEE 802.3-2018 45.2.3.10 EEE control and capability 1 (Register 3.20)
- IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register
(Register 1.2295)
Since I was not able to find any flag signaling support of these
registers, we should detect link mode abilities first and then based on
these abilities doing EEE link modes detection.
Results of EEE ability detection will be stored into new variable
phydev->supported_eee.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverity reported the following:
*** CID 1530573: (UNINIT)
drivers/net/phy/phy-c45.c:1036 in genphy_c45_plca_set_cfg()
1030 return ret;
1031
1032 val = ret;
1033 }
1034
1035 if (plca_cfg->node_cnt >= 0)
vvv CID 1530573: (UNINIT)
vvv Using uninitialized value "val".
1036 val = (val & ~MDIO_OATC14_PLCA_NCNT) |
1037 (plca_cfg->node_cnt << 8);
1038
1039 if (plca_cfg->node_id >= 0)
1040 val = (val & ~MDIO_OATC14_PLCA_ID) |
1041 (plca_cfg->node_id);
drivers/net/phy/phy-c45.c:1076 in genphy_c45_plca_set_cfg()
1070 return ret;
1071
1072 val = ret;
1073 }
1074
1075 if (plca_cfg->burst_cnt >= 0)
vvv CID 1530573: (UNINIT)
vvv Using uninitialized value "val".
1076 val = (val & ~MDIO_OATC14_PLCA_MAXBC) |
1077 (plca_cfg->burst_cnt << 8);
1078
1079 if (plca_cfg->burst_tmr >= 0)
1080 val = (val & ~MDIO_OATC14_PLCA_BTMR) |
1081 (plca_cfg->burst_tmr);
This is not actually creating a real problem because the path leading to
'val' being used uninitialized will eventually override the full content
of that variable before actually using it for writing the register.
However, the fix is simple and comes at basically no cost.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Fixes: 493323416f ("drivers/net/phy: add helpers to get/set PLCA configuration")
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/f22f1864165a8dbac8b7a2277f341bc8e7a7b70d.1674056765.git.piergiorgio.beruto@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support in phylib to read/write PLCA configuration for
Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA
Management Registers" specifications. These can be found at
https://www.opensig.org/about/specifications/
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case master/slave clock role is not specified (which is default), the
aneg registers will not be written.
The visible impact of this is missing pause advertisement.
So, rework genphy_c45_baset1_an_config_aneg() to be able to write
advertisement registers even if clock role is unknown.
Fixes: 3da8ffd854 ("net: phy: Add 10BASE-T1L support in phy-c45")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805073159.908643-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export genphy_c45_baset1_read_status() to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since MDIO_PMA_PMD_BT1_CTRL register shows actual configuration (and
forced state configuration is equal to the state), we should show
this configuration for ethtool.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move baset1 specific part of genphy_c45_read_pma() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not change default master/slave forced configuration if no changes was
requested.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move baset1 specific part of genphy_c45_pma_setup_forced() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not change default master/slave autoneg configuration if no
changes was requested.
Fixes: 3da8ffd854 ("net: phy: Add 10BASE-T1L support in phy-c45")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is needed because the BASE-T1 uses different registers
for status, control and advertisement to those already
employed in the existing phy-c45 functions.
Where required, genphy_c45 functions will now check whether
the device supports BASE-T1 and use the specific registers
instead: 45.2.7.19 BASE-T1 AN control register,
45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN
advertisement register, 45.2.7.22 BASE-T1 AN LP Base
Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control
register.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed warning: Function parameter or member 'enable' not
described in 'genphy_c45_fast_retrain'
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211026102957.17100-1-luoj@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add generic fast retrain auto-negotiation function for C45 PHYs.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some repeated words in some comments, they should be deleted.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic PMA suspend and resume callback functions for C45 PHYs.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic code to enable C45 PHY loopback into the common phy-c45.c
file. This will allow C45 PHY drivers aceess this by setting
.set_loopback.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have two competing requirements for the devices_in_package field.
We want to use it as a bit array indicating which MMDs are present, but
we also want to know if the Clause 22 registers are present.
Since "devices in package" is a term used in the 802.3 specification,
keep this as the as-specified values read from the PHY, and introduce
a new member "mmds_present" to indicate which MMDs are actually
present in the PHY, derived from the "devices in package" value.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
we don't need genphy_no_soft_reset() any longer. Not setting
callback soft_reset results in a no-op now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
When auto-negotiation is not required, return value should be zero.
Changes v1->v2:
- improved comments and code as Andrew Lunn and Heiner Kallweit suggestion
- fixed issue in genphy_c45_check_and_restart_aneg as Russell King
suggestion.
Fixes: 2a10ab043a ("net: phy: add genphy_check_and_restart_aneg()")
Fixes: 1af9f16840 ("net: phy: add genphy_c45_check_and_restart_aneg()")
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 93c0970493 ("net: phy: consider latched link-down status in
polling mode") removed double-read of latched link-state register for
polling mode from genphy_update_link(). This added extra ~1s delay into
sequence link down->up.
Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up. In phy_state_machine is checked
link state but it is latched "link is down". The state machine is
scheduled after one second and there is detected "link is up". This
extra delay can be avoided when we keep link-state register double read
in case when link was down previously.
With this solution we don't miss a link-down event in polling mode and
link-up is faster.
Details about this quirky behavior on Realtek phy:
Without patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
here i read link-down (BMSR_LSTATUS==0),
T0+5s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
up-to-date link-up is read (BMSR_LSTATUS==1),
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
With patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
first BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==0,
second BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==1,
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34786005ec ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e8270 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
