hid_connect() will call hid_pidff_init() which does
hid_device_io_start() leading to an "io already started" warning.
To fix this call hid_device_io_stop() before calling hid_connect(),
stopping IO means that connect events may be lost while hid_connect()
runs, re-enable IO and move the hidpp_connect_event() work queuing
after the hid_connect().
Note re-enabling IO is also necessary for the g920_get_config()
call later during hidpp_probe().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231025190151.302376-1-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
HIDPP unifying is only checked once in probe() and it is also
set by probe() itself.
Drop the quirk and replace its one check by the condition which is
used to set the quirk in the first place.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-13-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Drop delayed_work_cb() instead make hidpp_connect_event() the workqueue
function itself.
Besides resulting in a small cleanup this will hopefully also make
it clearer that going forward hidpp_connect_event() should only
be run from a workqueue and not be directly invoked.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-12-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
There is a connect event race in hidpp_probe() in these 2 lines:
connected = hidpp_root_get_protocol_version(hidpp) == 0;
atomic_set(&hidpp->connected, connected);
Specifically the following can happen:
1. This line from hidpp_probe() is executed:
connected = hidpp_root_get_protocol_version(hidpp) == 0;
and sets connected to false;
2. A connect-event packet is received and does:
atomic_set(&hidpp->connected, true);
3. The next line from hidpp_probe() is executed:
atomic_set(&hidpp->connected, connected);
and sets the atomic_t back to 0 again.
4. hidpp_connect_event() runs and sees the connected device
as disconnected because of this.
To fix this make hidpp_connect_event() query the connection status
of the device itself instead of having it rely on possibly stale
data cached in struct hidpp_device.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-11-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Remove the unused connected function parameter from wtp_connect(),
m560_send_config_command() and k400_connect().
This is a preparation patch for moving all connected state handling
to hidpp_connect_event().
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-10-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Turn hidpp_overwrite_name() into a hidpp_non_unifying_init() helper
which takes care of setting both the name and the serial for non
unifying devices.
This mirrors the hidpp_unifying_init() helper for unifying devices.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-8-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Move the hidpp_overwrite_name() call to before the connect check, this
puts it at the same place in the probe() order as hidpp_serial_init()
which seems more logical. This should not make a difference since this
is in the non-unifying path and only unifying devices can be probed
in non-connected state.
This is a preparation patch for moving all connected state handling
to hidpp_connect_event().
Doing this before the connect check requires dropping the protocol
version check since protocol_major is not set yet now. Instead
this relies on hidpp_root_get_feature(HIDPP_PAGE_GET_DEVICE_NAME_TYPE)
failing on older devices, just like how hidpp_get_serial() relies on
hidpp_root_get_feature(HIDPP_PAGE_DEVICE_INFORMATION) failing on older
devices. So this again makes the code more consistent.
Also stop printing an error on failure now, since with the proto
version check gone failures are expected to happen on older devices.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-7-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The data retrieved by g920_get_config() is only used by hidpp_ff_init().
Now that the hw is kept open till the end of probe() the g920_get_config()
call can be moved to just before hidpp_ff_init() to have all
the HIDPP_QUIRK_CLASS_G920 together in a single place.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-6-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
For WTP devices which start disconnected (paired with the unifying
receiver, but not connected atm) hidpp_connect_event() takes care
of calling wtp_get_config() when the device later connects.
There is no need to have a separate code path for WTP devices which
are connected at probe() time, these can use the same code-path since
probe() will queue hidpp_connect_event() for those at probe time.
Drop the unnecessary wtp_get_config() call from probe().
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-5-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Calling get_wireless_feature_index() from probe() causes
the wireless_feature_index to only get set for unifying devices which
are already connected at probe() time. It does not get set for devices
which connect later.
Fix this by moving get_wireless_feature_index() to hidpp_connect_event(),
this does not make a difference for devices connected at probe() since
probe() will queue the hidpp_connect_event() for those at probe time.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Fixes: 0da0a63b7c ("HID: logitech-hidpp: Support WirelessDeviceStatus connect events")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-4-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Commit 91cf9a98ae ("HID: logitech-hidpp: make .probe usbhid capable")
makes hidpp_probe() first call hid_hw_start(hdev, 0) to allow IO
without connecting any hid subdrivers (hid-input, hidraw).
This is done to allow to retrieve the device's name and serial number
and store these in hdev->name and hdev->uniq.
Then later on IO was stopped and started again with hid_hw_start(hdev,
HID_CONNECT_DEFAULT) connecting hid-input and hidraw after the name
and serial number have been setup.
Commit 498ba20690 ("HID: logitech-hidpp: Don't restart communication
if not necessary") changed the probe() code to only do the start with
a 0 connect-mask + restart later for unifying devices.
But for non unifying devices hdev->name and hdev->uniq are updated too.
So this change re-introduces the problem for which the start with
a 0 connect-mask + restart later behavior was introduced.
The previous patch in this series changes the unifying path to instead of
restarting IO only call hid_connect() later. This avoids possible issues
with restarting IO seen on non unifying devices.
Revert the change to limit the restart behavior to unifying devices to
fix hdev->name changing after userspace facing devices have already been
registered.
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Fixes: 498ba20690 ("HID: logitech-hidpp: Don't restart communication if not necessary")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-3-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Restarting IO causes 2 problems:
1. Some devices do not like IO being restarted this was addressed in
commit 498ba20690 ("HID: logitech-hidpp: Don't restart communication
if not necessary"), but that change has issues of its own and needs to
be reverted.
2. Restarting IO and specifically calling hid_device_io_stop() causes
received packets to be missed, which may cause connect-events to
get missed.
Restarting IO was introduced in commit 91cf9a98ae ("HID: logitech-hidpp:
make .probe usbhid capable") to allow to retrieve the device's name and
serial number and store these in hdev->name and hdev->uniq before
connecting any hid subdrivers (hid-input, hidraw) exporting this info
to userspace.
But this does not require restarting IO, this merely requires deferring
calling hid_connect(). Calling hid_hw_start() with a connect-mask of
0 makes it skip calling hid_connect(), so hidpp_probe() can simply call
hid_connect() later without needing to restart IO.
Remove the stop + restart of IO and instead just call hid_connect() later
to avoid the issues caused by restarting IO.
Now that IO is no longer stopped, hid_hw_close() must be called at the end
of probe() to balance the hid_hw_open() done at the beginning probe().
This series has been tested on the following devices:
Logitech Bluetooth Laser Travel Mouse (bluetooth, HID++ 1.0)
Logitech M720 Triathlon (bluetooth, HID++ 4.5)
Logitech M720 Triathlon (unifying, HID++ 4.5)
Logitech K400 Pro (unifying, HID++ 4.1)
Logitech K270 (eQUAD nano Lite, HID++ 2.0)
Logitech M185 (eQUAD nano Lite, HID++ 4.5)
Logitech LX501 keyboard (27 Mhz, HID++ builtin scroll-wheel, HID++ 1.0)
Logitech M-RAZ105 mouse (27 Mhz, HID++ extra mouse buttons, HID++ 1.0)
And by bentiss:
Logitech Touchpad T650 (unifying)
Logitech Touchpad T651 (bluetooth)
Logitech MX Master 3B (BLE)
Logitech G403 (plain USB / Gaming receiver)
Fixes: 498ba20690 ("HID: logitech-hidpp: Don't restart communication if not necessary")
Suggested-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231010102029.111003-2-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Through the usage of pm_ptr() the CONFIG_PM-dependent code will always be
compiled, protecting against bitrot.
The linker will then garbage-collect the unused function avoiding any overhead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20231012-hid-pm_ptr-v1-4-0a71531ca93b@weissschuh.net
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Through the usage of pm_ptr() the CONFIG_PM-dependent code will always be
compiled, protecting against bitrot.
The linker will then garbage-collect the unused function avoiding any overhead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20231012-hid-pm_ptr-v1-3-0a71531ca93b@weissschuh.net
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Through the usage of pm_ptr() the CONFIG_PM-dependent code will always be
compiled, protecting against bitrot.
The linker will then garbage-collect the unused function avoiding any overhead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20231012-hid-pm_ptr-v1-2-0a71531ca93b@weissschuh.net
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The USB Compact Keyboard variant requires a reset_resume function to
restore keyboard configuration after a suspend in some situations. Move
configuration normally done on probe to lenovo_features_set_cptkbd(), then
recycle this for use on reset_resume.
Without, the keyboard and driver would end up in an inconsistent state,
breaking middle-button scrolling amongst other problems, and twiddling
sysfs values wouldn't help as the middle-button mode won't be set until
the driver is reloaded.
Tested on a USB and Bluetooth Thinkpad Compact Keyboard.
CC: stable@vger.kernel.org
Fixes: 94eefa2713 ("HID: lenovo: Use native middle-button mode for compact keyboards")
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Link: https://lore.kernel.org/r/20231002150914.22101-1-martink@posteo.de
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Previously cp2112_gpio_irq_shutdown() always cancelled the
gpio_poll_worker, even if other IRQs were still active, and did not set
the gpio_poll flag to false. This resulted in any call to _shutdown()
resulting in interrupts no longer functioning on the chip until a
_remove() occurred (a.e. the cp2112 is unplugged or system rebooted).
Only cancel polling if all IRQs are disabled/masked, and correctly set
the gpio_poll flag, allowing polling to restart when an interrupt is
next enabled.
Signed-off-by: Danny Kaehn <danny.kaehn@plexus.com>
Fixes: 13de9cca51 ("HID: cp2112: add IRQ chip handling")
Link: https://lore.kernel.org/r/20231011182317.1053344-1-danny.kaehn@plexus.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU)
races when it races with itself.
hidpp_connect_event() primarily runs from a workqueue but it also runs
on probe() and if a "device-connected" packet is received by the hw
when the thread running hidpp_connect_event() from probe() is waiting on
the hw, then a second thread running hidpp_connect_event() will be
started from the workqueue.
This opens the following races (note the below code is simplified):
1. Retrieving + printing the protocol (harmless race):
if (!hidpp->protocol_major) {
hidpp_root_get_protocol_version()
hidpp->protocol_major = response.rap.params[0];
}
We can actually see this race hit in the dmesg in the abrt output
attached to rhbz#2227968:
[ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
[ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
Testing with extra logging added has shown that after this the 2 threads
take turn grabbing the hw access mutex (send_mutex) so they ping-pong
through all the other TOCTOU cases managing to hit all of them:
2. Updating the name to the HIDPP name (harmless race):
if (hidpp->name == hdev->name) {
...
hidpp->name = new_name;
}
3. Initializing the power_supply class for the battery (problematic!):
hidpp_initialize_battery()
{
if (hidpp->battery.ps)
return 0;
probe_battery(); /* Blocks, threads take turns executing this */
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
}
4. Creating delayed input_device (potentially problematic):
if (hidpp->delayed_input)
return;
hidpp->delayed_input = hidpp_allocate_input(hdev);
The really big problem here is 3. Hitting the race leads to the following
sequence:
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
...
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
So now we have registered 2 power supplies for the same battery,
which looks a bit weird from userspace's pov but this is not even
the really big problem.
Notice how:
1. This is all devm-maganaged
2. The hidpp->battery.desc struct is shared between the 2 power supplies
3. hidpp->battery.desc.properties points to the result from the second
devm_kmemdup()
This causes a use after free scenario on USB disconnect of the receiver:
1. The last registered power supply class device gets unregistered
2. The memory from the last devm_kmemdup() call gets freed,
hidpp->battery.desc.properties now points to freed memory
3. The first registered power supply class device gets unregistered,
this involves sending a remove uevent to userspace which invokes
power_supply_uevent() to fill the uevent data
4. power_supply_uevent() uses hidpp->battery.desc.properties which
now points to freed memory leading to backtraces like this one:
Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08
...
Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event
Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0
...
Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0
Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0
Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680
Sep 22 20:01:35 eric kernel: power_supply_unregister+0x8e/0xa0
Sep 22 20:01:35 eric kernel: release_nodes+0x3d/0xb0
Sep 22 20:01:35 eric kernel: devres_release_group+0xfc/0x130
Sep 22 20:01:35 eric kernel: hid_device_remove+0x56/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: logi_dj_remove+0x9a/0x100 [hid_logitech_dj 5c91534a0ead2b65e04dd799a0437e3b99b21bc4]
Sep 22 20:01:35 eric kernel: hid_device_remove+0x44/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: usbhid_disconnect+0x47/0x60 [usbhid 727dcc1c0b94e6b4418727a468398ac3bca492f3]
Sep 22 20:01:35 eric kernel: usb_unbind_interface+0x90/0x270
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? kobject_put+0xa0/0x1d0
Sep 22 20:01:35 eric kernel: usb_disable_device+0xcd/0x1e0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xde/0x2c0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xc3/0x2c0
Sep 22 20:01:35 eric kernel: hub_event+0xe80/0x1c10
There have been quite a few bug reports (see Link tags) about this crash.
Fix all the TOCTOU issues, including the really bad power-supply related
system crash on USB disconnect, by making probe() use the workqueue for
running hidpp_connect_event() too, so that it can never run more then once.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227221
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2242189
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412#c58
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231005182638.3776-1-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
A recent commit reordered probe so that the interrupt line is now
requested before making sure that the device exists.
This breaks machines like the Lenovo ThinkPad X13s which rely on the
HID driver to probe second-source devices and only register the variant
that is actually populated. Specifically, the interrupt line may now
already be (temporarily) claimed when doing asynchronous probing of the
touchpad:
genirq: Flags mismatch irq 191. 00082008 (hid-over-i2c) vs. 00082008 (hid-over-i2c)
i2c_hid_of 21-0015: Could not register for hid-over-i2c interrupt, irq = 191, ret = -16
i2c_hid_of: probe of 21-0015 failed with error -16
Fix this by restoring the old behaviour of first making sure the device
exists before requesting the interrupt line.
Note that something like this should probably be implemented also for
"panel followers", whose actual probe is currently effectively deferred
until the DRM panel is probed (e.g. by powering down the device after
making sure it exists and only then register it as a follower).
Fixes: 675cd877c9 ("HID: i2c-hid: Rearrange probe() to power things up later")
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20231002155857.24584-1-johan+linaro@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Like various other devices using similar hardware, this model reports a
perpetually empty battery (0-1%).
Join the others and apply HID_BATTERY_QUIRK_IGNORE.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
service, which allows to wakup device when the system is in S5 (Soft-Off
state). This OOB service can be enabled/disabled from BIOS settings. When
enabled, the ISH device gets PME wake capability. To enable PME wakeup,
driver also needs to enable ACPI GPE bit.
On resume, BIOS will clear the wakeup bit. So driver need to re-enable it
in resume function to keep the next wakeup capability. But this BIOS
clearing of wakeup bit doesn't decrement internal OS GPE reference count,
so this reenabling on every resume will cause reference count to overflow.
So first disable and reenable ACPI GPE bit using acpi_disable_gpe().
Fixes: 2e23a70eda ("HID: intel-ish-hid: ipc: finish power flow for EHL OOB")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://lore.kernel.org/lkml/CAAd53p4=oLYiH2YbVSmrPNj1zpMcfp=Wxbasb5vhMXOWCArLCg@mail.gmail.com/T/
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usb_free_urb() does the NULL check itself, so there is no need to duplicate
it prior to calling.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1cd4004cd ("HID: sony: Fix a potential memory leak in sony_probe()")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When suspending the computer, a Switch Pro Controller connected via USB will
lose its internal status. However, because the USB connection was technically
never lost, when resuming the computer, the driver will attempt to communicate
with the controller as if nothing happened (and fail).
Because of this, the user was forced to manually disconnect the controller
(or to press the sync button on the controller to power it off), so that it
can be re-initialized.
With this patch, the controller will be automatically re-initialized after
resuming from suspend.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216233
Signed-off-by: Martino Fontana <tinozzo123@gmail.com>
Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing calls.
Fixes: 3ab196f882 ("HID: nvidia-shield: Add battery support for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing call. Make sure it is safe to call in the probe error
handling path by preventing the led_classdev from attempting to set the LED
brightness to the off state on unregister.
Fixes: f88af60e74 ("HID: nvidia-shield: Support LED functionality for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Register the Synaptics device as a special multitouch device with certain
quirks that may improve usability of the touchpad device.
Reported-by: Rain <rain@sunshowers.io>
Closes: https://lore.kernel.org/linux-input/2bbb8e1d-1793-4df1-810f-cb0137341ff4@app.fastmail.com/
Signed-off-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously the cp2112 driver called INIT_DELAYED_WORK within
cp2112_gpio_irq_startup, resulting in duplicate initilizations of the
workqueue on subsequent IRQ startups following an initial request. This
resulted in a warning in set_work_data in workqueue.c, as well as a rare
NULL dereference within process_one_work in workqueue.c.
Initialize the workqueue within _probe instead.
Fixes: 13de9cca51 ("HID: cp2112: add IRQ chip handling")
Signed-off-by: Danny Kaehn <danny.kaehn@plexus.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Support player LED patterns up to 8 players.
(Note that the behavior still consinsts in increasing the player number
every time a controller is connected, never decreasing it. It should be
as is described in https://bugzilla.kernel.org/show_bug.cgi?id=216225.
However, any implementation here would stop making sense as soon as a
non-Nintendo controller is connected, which is why I'm not bothering.)
- Split part of `joycon_home_led_brightness_set` (which is called by hid)
into `joycon_set_home_led` (which is what actually sets the LEDs), for
consistency with player LEDs.
- `joycon_player_led_brightness_set` won't try it to "determine which
player led this is" anymore: it's already looking at every LED
brightness value.
- Instead of first registering the `led_classdev`, then attempting to set
the LED and unregistering the `led_classdev` if it fails, first attempt
to set the LED, then register the `led_classdev` only if it succeeds
(the class is still filled up in either case).
- If setting the player LEDs fails, still attempt setting the home LED.
(I don't know there's a third party controller where this may actually
happen, but who knows...)
- Use `JC_NUM_LEDS` where appropriate instead of 4.
- Print return codes in more places.
- Use spinlock instead of mutex for `input_num`. Copy its value to a local
variable, so that it can be unlocked immediately.
- `input_num` starts counting from 0
- Less holding of mutexes in general.
Signed-off-by: Martino Fontana <tinozzo123@gmail.com>
Reviewed-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Built-in firmware of cptkbd handles scrolling by itself (when middle
button is pressed) but with issues: it does not support horizontal and
hi-res scrolling and upon middle button release it sends middle button
click even if there was a scrolling event. Commit 3cb5ff0220 ("HID:
lenovo: Hide middle-button press until release") workarounds last
issue but it's impossible to workaround scrolling-related issues
without firmware modification.
Likely, Dennis Schneider has reverse engineered the firmware and
provided an instruction on how to patch it [1]. However,
aforementioned workaround prevents userspace (libinput) from knowing
exact moment when middle button has been pressed down and performing
"On-Button scrolling". This commit detects correctly-behaving patched
firmware if cursor movement events has been received during middle
button being pressed and stops applying workaround for this device.
Link: https://hohlerde.org/rauch/en/elektronik/projekte/tpkbd-fix/ [1]
Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In order to simplify some error handling paths and avoid code duplication,
introduce thunderstrike_destroy() which undoes thunderstrike_create().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing calls.
Fixes: 3ab196f882 ("HID: nvidia-shield: Add battery support for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit in Fixes updated the error handling path of
thunderstrike_create() and the remove function but not the error handling
path of shield_probe(), should an error occur after a successful
thunderstrike_create() call.
Add the missing call. Make sure it is safe to call in the probe error
handling path by preventing the led_classdev from attempting to set the LED
brightness to the off state on unregister.
Fixes: f88af60e74 ("HID: nvidia-shield: Support LED functionality for Thunderstrike")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery information reported by the driver depends on the power supply
subsystem. Select the required subsystem when the HID_NVIDIA_SHIELD Kconfig
option is enabled.
Fixes: 3ab196f882 ("HID: nvidia-shield: Add battery support for Thunderstrike")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a slab-out-of-bounds Write bug in hid-holtek-kbd driver.
The problem is the driver assumes the device must have an input
but some malicious devices violate this assumption.
Fix this by checking hid_device's input is non-empty before its usage.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-nvidia-shield driver uses functions that are built
only when LEDS_CLASS is set, so make the driver depend on that
symbol to prevent build errors.
riscv32-linux-ld: drivers/hid/hid-nvidia-shield.o: in function `.L11':
hid-nvidia-shield.c:(.text+0x192): undefined reference to `led_classdev_unregister'
riscv32-linux-ld: drivers/hid/hid-nvidia-shield.o: in function `.L113':
hid-nvidia-shield.c:(.text+0xfa4): undefined reference to `led_classdev_register_ext'
Fixes: 09308562d4 ("HID: nvidia-shield: Initial driver implementation with Thunderstrike support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using hidpp for the M720 adds battery info reporting and hires
scrolling support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid_hw_raw_request() function returns negative error codes or the
number bytes transferred. The problem is that when it returns negative
error codes and we check if "ret < sizeof(arctis_1_battery_request)",
then the negative values are type promoted from int to high unsigned long
values and treated as success.
This was detected using Smatch:
drivers/hid/hid-steelseries.c:393 steelseries_headset_arctis_1_fetch_battery()
warn: error code type promoted to positive: 'ret'
Fixes: a0c76896c3 ("HID: steelseries: Add support for Arctis 1 XBox")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If an error occurs after a successful usb_alloc_urb() call, usb_free_urb()
should be called.
Fixes: fb1a79a6b6 ("HID: sony: fix freeze when inserting ghlive ps3/wii dongles")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----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=24SV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2023083101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- devm fixes for problems that caused use-after-free reports (Rahul
Rameshbabu)
- Some extensive HID docs (Marco Morandini)
- Constification of struct class (Ivan Orlov and Greg Kroah-Hartman)
- Google Stadia Force Feedback support (Fabio Baltieri)
- Various fixes and new device ID support
* tag 'for-linus-2023083101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (42 commits)
HID: logitech-hidpp: rework one more time the retries attempts
HID: nvidia-shield: Reference hid_device devm allocation of input_dev name
HID: multitouch: Correct devm device reference for hidinput input_dev name
HID: uclogic: Correct devm device reference for hidinput input_dev name
HID: logitech-dj: Fix error handling in logi_dj_recv_switch_to_dj_mode()
HID: i2c-hid: elan: Add ili9882t timing
dt-bindings: input: i2c-hid: Introduce Ilitek ili9882t
HID: apple: Add "Hailuck" to the list of non-apple keyboards
HID: steelseries: arctis_1_battery_request[] should be static
MAINTAINERS: update my email address
HID: logitech-hidpp: Add support for Logitech MX Anywhere 3 mouse
HID: wacom: struct name cleanup
HID: wacom: remove unnecessary 'connected' variable from EKR
HID: wacom: remove the battery when the EKR is off
HID: nvidia-shield: Update Thunderstrike LED instance name to use id
HID: nvidia-shield: Add battery support for Thunderstrike
HID: nvidia-shield: Remove led_classdev_unregister in thunderstrike_create
HID: hid-google-stadiaff: add support for Stadia force feedback
HID: logitech-dj: Add support for a new lightspeed receiver iteration
HID: logitech-hidpp: Add support for the Pro X Superlight
...
Here is a small set of driver core updates and additions for 6.6-rc1.
Included in here are:
- stable kernel documentation updates
- class structure const work from Ivan on various subsystems
- kernfs tweaks
- driver core tests!
- kobject sanity cleanups
- kobject structure reordering to save space
- driver core error code handling fixups
- other minor driver core cleanups
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH77Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZMACePk8SitfaJc6FfFf5I7YK7Nq0V8MAn0nUjgsR
i8NcNpu/Yv4HGrDgTdh/
=PJbk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core updates and additions for 6.6-rc1.
Included in here are:
- stable kernel documentation updates
- class structure const work from Ivan on various subsystems
- kernfs tweaks
- driver core tests!
- kobject sanity cleanups
- kobject structure reordering to save space
- driver core error code handling fixups
- other minor driver core cleanups
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
driver core: Call in reversed order in device_platform_notify_remove()
driver core: Return proper error code when dev_set_name() fails
kobject: Remove redundant checks for whether ktype is NULL
kobject: Add sanity check for kset->kobj.ktype in kset_register()
drivers: base: test: Add missing MODULE_* macros to root device tests
drivers: base: test: Add missing MODULE_* macros for platform devices tests
drivers: base: Free devm resources when unregistering a device
drivers: base: Add basic devm tests for platform devices
drivers: base: Add basic devm tests for root devices
kernfs: fix missing kernfs_iattr_rwsem locking
docs: stable-kernel-rules: mention that regressions must be prevented
docs: stable-kernel-rules: fine-tune various details
docs: stable-kernel-rules: make the examples for option 1 a proper list
docs: stable-kernel-rules: move text around to improve flow
docs: stable-kernel-rules: improve structure by changing headlines
base/node: Remove duplicated include
kernfs: attach uuid for every kernfs and report it in fsid
kernfs: add stub helper for kernfs_generic_poll()
x86/resctrl: make pseudo_lock_class a static const structure
x86/MSR: make msr_class a static const structure
...
