Use modern string_choices API instead of manually determining the
output using ternary operator.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240603181938.76047-3-wahrenst@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 8ff05989b4 ("pinctrl: bcm2835: Make pin freeing behavior
configurable") unintentionally made the module parameter
persist_gpio_outputs changeable at runtime. So drop the write permission
in order to make the freeing behavior predictable for user applications.
Fixes: 8ff05989b4 ("pinctrl: bcm2835: Make pin freeing behavior configurable")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Closes: https://lore.kernel.org/linux-gpio/Zjk-C0nLmlynqLAE@surfacebook.localdomain/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240603181938.76047-2-wahrenst@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Until now after a bcm2835 pin was freed its pinmux was set to GPIO_IN.
So in case it was configured as GPIO_OUT before the configured output
level also get lost. As long as GPIO sysfs was used this wasn't
actually a problem because the pins and their possible output level
were kept by sysfs.
Since more and more Raspberry Pi users start using libgpiod they are
confused about this behavior. So make the pin freeing behavior of
GPIO_OUT configurable via module parameter. In case
pinctrl-bcm2835.persist_gpio_outputs is set to 1, the output level is
kept.
This patch based on the downstream work of Phil Elwell.
Link: https://github.com/raspberrypi/linux/pull/6117
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Message-ID: <20240503062745.11298-1-wahrenst@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BCM2711 allows to read the bias config. So implement pin_conf_get
accordingly. The pull resistor values has been taken from the
BCM2711/7211 datasheet.
This implementation assumes that BCM7211 behaves the same way.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Message-ID: <20240307070113.4888-3-wahrenst@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Even the driver already has implemented pin_dbg_show, it could
be helpful to implement pin_conf_get for a more generic behavior.
Contrary to the BCM2711, the BCM2835 SOC doesn't allow to read
the bias config, so the implementation is limited to the basics.
Keep ENOTSUPP here, because it's only used internally.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Message-ID: <20240307070113.4888-2-wahrenst@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the past setting the pin direction called pinctrl_gpio_direction()
which uses a mutex to serialize this. That was changed to set the
direction directly in the pin controller driver, but that lost the
serialization mechanism. Since the direction of multiple pins are in
the same register you can have a race condition, something that was
in fact observed with the cec-gpio driver.
Add a new spinlock to serialize writing to the FSEL registers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 1a4541b68e ("pinctrl-bcm2835: don't call pinctrl_gpio_direction()")
Link: https://lore.kernel.org/r/4302b66b-ca20-0f19-d2aa-ee8661118863@xs4all.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Yeah, while the ->add_pin_ranges() shouldn't be used by DT drivers,
this one requires it to support quite old firmware descriptions that
do not have gpio-ranges property.
The change allows to clean up GPIO library from OF specifics.
There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230113215352.44272-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 6c846d026d ("gpio: Don't fiddle with irqchips marked as
immutable") added a warning to indicate if the gpiolib is altering the
internals of irqchips. The bcm2835 pinctrl is also affected by this
warning.
Fix this by making the irqchip in the bcm2835 pinctrl driver immutable.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220614202831.236341-3-stefan.wahren@i2se.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit b8a19382ac ("pinctrl: bcm2835: Fix support for threaded level
triggered IRQs") assigned the irq_mask/unmask callbacks with the
already existing functions for irq_enable/disable. The wasn't completely
the right way (tm) to fix the issue, because these callbacks shouldn't
be identical. So fix this by rename the functions to represent their
intension and drop the unnecessary irq_enable/disable assigment.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220614202831.236341-2-stefan.wahren@i2se.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit c8013355ea ("ARM: dts: gpio-ranges property is now required")
fixed the GPIO probing issues caused by "pinctrl: bcm2835: Change init
order for gpio hogs". This changed only the kernel DTS files. Unfortunately
it isn't guaranteed that these files are shipped to all users.
So implement the necessary backward compatibility for BCM2835 and
BCM2711 platform.
Fixes: 266423e60e ("pinctrl: bcm2835: Change init order for gpio hogs")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220409095129.45786-3-stefan.wahren@i2se.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 266423e60e ("pinctrl: bcm2835: Change init order for gpio
hogs") a few error paths would not unwind properly the registration of
gpio ranges. Correct that by assigning a single error label and goto it
whenever we encounter a fatal error.
Fixes: 266423e60e ("pinctrl: bcm2835: Change init order for gpio hogs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220127215033.267227-1-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- New standard enumerator and corresponding device tree bindings
for output impedance pin configuration. (Implemented and used
in the Renesas rzg2l driver.)
- Cleanup of Kconfig and Makefile to be somewhat orderly and
alphabetic.
New drivers:
- Samsung Exynos 7885 pin controller.
- Ocelot LAN966x pin controller.
- Qualcomm SDX65 pin controller.
- Qualcomm SM8450 pin controller.
- Qualcomm PM8019, PM8226 and PM2250 pin controllers.
- NXP/Freescale i.MXRT1050 pin controller.
- Intel Thunder Bay pin controller.
Enhancements:
- Introduction of the string library helper function
"kasprintf_strarray()" and subsequent use in Rockchip, ST and
Armada pin control drivers, as well as the GPIO mockup driver.
- The Ocelot pin controller has been extensively rewritten to
use regmap and other modern kernel infrastructure.
- The Microchip SGPIO driver has been converted to use regmap.
- The SPEAr driver had been converted to use regmap.
- Substantial cleanups and janitorial on the Apple pin control
driver that was merged for v5.16.
- Janitorial to remove of_node assignments in the GPIO portions
that anyway get this handled in the GPIO core.
- Minor cleanups and improvements in several pin controllers.
-----BEGIN PGP SIGNATURE-----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=+nxh
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk updates from Linus Walleij:
"Core changes:
- New standard enumerator and corresponding device tree bindings for
output impedance pin configuration. (Implemented and used in the
Renesas rzg2l driver.)
- Cleanup of Kconfig and Makefile to be somewhat orderly and
alphabetic.
New drivers:
- Samsung Exynos 7885 pin controller.
- Ocelot LAN966x pin controller.
- Qualcomm SDX65 pin controller.
- Qualcomm SM8450 pin controller.
- Qualcomm PM8019, PM8226 and PM2250 pin controllers.
- NXP/Freescale i.MXRT1050 pin controller.
- Intel Thunder Bay pin controller.
Enhancements:
- Introduction of the string library helper function
"kasprintf_strarray()" and subsequent use in Rockchip, ST and
Armada pin control drivers, as well as the GPIO mockup driver.
- The Ocelot pin controller has been extensively rewritten to use
regmap and other modern kernel infrastructure.
- The Microchip SGPIO driver has been converted to use regmap.
- The SPEAr driver had been converted to use regmap.
- Substantial cleanups and janitorial on the Apple pin control driver
that was merged for v5.16.
- Janitorial to remove of_node assignments in the GPIO portions that
anyway get this handled in the GPIO core.
- Minor cleanups and improvements in several pin controllers"
* tag 'pinctrl-v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (98 commits)
pinctrl: imx: fix assigning groups names
dt-bindings: pinctrl: mt8195: add wrapping node of pin configurations
pinctrl: bcm: ns: use generic groups & functions helpers
pinctrl: imx: fix allocation result check
pinctrl: samsung: Use platform_get_irq_optional() to get the interrupt
pinctrl: Propagate firmware node from a parent device
dt-bindings: pinctrl: qcom: Add SDX65 pinctrl bindings
pinctrl: add one more "const" for generic function groups
pinctrl: keembay: rework loops looking for groups names
pinctrl: keembay: comment process of building functions a bit
pinctrl: imx: prepare for making "group_names" in "function_desc" const
ARM: dts: gpio-ranges property is now required
pinctrl: aspeed: fix unmet dependencies on MFD_SYSCON for PINCTRL_ASPEED
pinctrl: Get rid of duplicate of_node assignment in the drivers
pinctrl-sunxi: don't call pinctrl_gpio_direction()
pinctrl-bcm2835: don't call pinctrl_gpio_direction()
pinctrl: bcm2835: Silence uninit warning
pinctrl: Sort Kconfig and Makefile entries alphabetically
pinctrl: Add Intel Thunder Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Thunderbay pinctrl driver
...
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove these assignment all at once.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211214125855.33207-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set the direction directly without calling pinctrl_gpio_direction().
This avoids the mutex_lock() calls in that function, which would
invalid the can_sleep = false.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206131648.1521868-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
...and gpio-ranges
pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio
side is registered first, but this breaks gpio hogs (which are
configured during gpiochip_add_data). Part of the hog initialisation
is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't
yet been registered this results in an -EPROBE_DEFER from which it can
never recover.
Change the initialisation sequence to register the pinctrl driver
first.
This also solves a similar problem with the gpio-ranges property, which
is required in order for released pins to be returned to inputs.
Fixes: 73345a18d4 ("pinctrl: bcm2835: Pass irqchip when adding gpiochip")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211206092237.4105895-2-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The uninitialized variable would be caught by the BUG_ON()
logic below, but the kernel test robot cannot see that.
Silence the warning by initializing the variable.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211209134513.306212-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the pinctrl-bcm2835 driver to support being built as as a module
by converting it to a module_platform_driver() with the appropriate
module license, authors and description.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://lore.kernel.org/r/20211019221127.1953001-1-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
no core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML
-----BEGIN PGP SIGNATURE-----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=I6N/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.15 kernel cycle, no
core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML"
* tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (53 commits)
pinctrl: renesas: Add RZ/G2L pin and gpio controller driver
pinctrl: samsung: Add Exynos850 SoC specific data
dt-bindings: pinctrl: samsung: Add Exynos850 doc
MAINTAINERS: Add maintainers for amd-pinctrl driver
pinctrl: Add Intel Keem Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Keembay pinctrl driver
pinctrl: zynqmp: Drop pinctrl_unregister for devm_ registered device
dt-bindings: pinctrl: qcom-pmic-gpio: Remove the interrupts property
dt-bindings: pinctrl: qcom-pmic-gpio: Convert qcom pmic gpio bindings to YAML
dt-bindings: pinctrl: mt8195: Use real world values for drive-strength arguments
dt-bindings: mediatek: convert pinctrl to yaml
arm: dts: mt8183: Move pinfunc to include/dt-bindings/pinctrl
arm: dts: mt8135: Move pinfunc to include/dt-bindings/pinctrl
pinctrl: ingenic: Add .max_register in regmap_config
pinctrl: ingenic: Fix bias config for X2000(E)
pinctrl: ingenic: Fix incorrect pull up/down info
pinctrl: Ingenic: Add pinctrl driver for X2100.
dt-bindings: pinctrl: Add bindings for Ingenic X2100.
pinctrl: Ingenic: Add SSI pins support for JZ4755 and JZ4760.
pinctrl: Ingenic: Improve the code.
...
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The if condition followed by BUG can be replaced to BUG_ON which is
more compact and formal in linux source.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210624064913.41788-1-wangborong@cdjrlc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The downstream .dts files only request two GPIO IRQs. Truncate the
array of parent IRQs when irq_of_parse_and_map returns 0.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210521090158.26932-1-iivanov@suse.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Leverage the IRQCHIP_MASK_ON_SUSPEND flag in order to avoid having to
specifically treat the GPIO interrupts during suspend and resume, and
simply implement an irq_set_wake() callback that is responsible for
enabling the parent wake-up interrupt as a wake-up interrupt.
To avoid allocating unnecessary resources for other chips, the wake-up
interrupts are only initialized if we have a brcm,bcm7211-gpio
compatibility string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-5-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BCM7211 SoC uses the same pinconf_ops as the ones defined for the
BCM2711 SoC, match the compatible string and use the correct set of
options.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-4-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.
Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.
Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prepares the platform data to be easier to extend for more GPIOs.
Except of this there is no functional change.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1581166975-22949-3-git-send-email-stefan.wahren@i2se.com
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion. The BCM2835 has multiple parents so let's
exploit the new facility in the GPIO_IRQCHIP to actually
deal with multiple parents.
Cc: Eric Anholt <eric@anholt.net>
Cc: Thierry Reding <treding@nvidia.com>
[Rebased on changes in the pinctrl tree]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20190812062729.1892-1-linus.walleij@linaro.org
The BCM2711 has a new way of selecting the pull-up/pull-down setting
for a GPIO pin. The registers used for the BCM2835, GP_PUD and
GP_PUDCLKn0, are no longer connected. A new set of registers,
GP_GPIO_PUP_PDN_CNTRL_REGx must be used. This commit will add
a new compatible string "brcm,bcm2711-gpio" and the kernel
driver will use it to select which method is used to select
pull-up/pull-down.
This patch based on a patch by Al Cooper which was intended for the
BCM7211. This is a bugfixed and improved version.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/1563776607-8368-3-git-send-email-wahrenst@gmx.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support GPIO config changes direct these to the generic pinctrl.
This also requires an adjust of the return code for unsupported parameter
otherwise gpiod_configure_flags wont work as expected.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 0de704955e ("pinctrl: bcm2835: Add support for
generic pinctrl binding") this driver is capable to use the generic
interface. So declare this accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns when one enumerated type is implicitly converted to another:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:707:40: warning: implicit
conversion from enumeration type 'enum bcm2835_pinconf_param' to
different enumeration type 'enum pin_config_param' [-Wenum-conversion]
configs[0] = pinconf_to_config_packed(BCM2835_PINCONF_PARAM_PULL, pull);
~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BCM2835 pinctrl driver acquires a spinlock in its ->irq_enable,
->irq_disable and ->irq_set_type callbacks. Spinlocks become sleeping
locks with CONFIG_PREEMPT_RT_FULL=y, therefore invocation of one of the
callbacks in atomic context may cause a hard lockup if at least two GPIO
pins in the same bank are used as interrupts. The issue doesn't occur
with just a single interrupt pin per bank because the lock is never
contended. I'm experiencing such lockups with GPIO 8 and 28 used as
level-triggered interrupts, i.e. with ->irq_disable being invoked on
reception of every IRQ.
The critical section protected by the spinlock is very small (one bitop
and one RMW of an MMIO register), hence converting to a raw spinlock
seems a better trade-off than converting the driver to threaded IRQ
handling (which would increase latency to handle an interrupt).
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Properties to set initial value of pin output buffer.
This can be useful for configure hardware in overlay files, and in early
boot for checking it states in QA sanity tests.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To keep driver up to date we add generic pinctrl binding support, which
covers the features used in this driver and has additional node properties
that this SoC has compatibility, so enabling future implementations of
these properties without the need to create new node properties in the
device trees.
The logic of this change maintain the old brcm legacy binding support in
order to keep the ABI stable.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----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=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
Fixing a small merge problem in BCM2835 related to the
new irqchip code.
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix the following build warning:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:376:15: warning: variable 'type' set but not used [-Wunused-but-set-variable]
Furthermore, it is unused for a long time, at least since commit 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
where a "FIXME no clue why the code looks up the type here" was added.
A year after, nobody answeered this question, so its time to remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_group field stores a 1:1 mapping. Use the loop variable to
derive the values instead of storing them in an extra array.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
18958 9000 128 28086 6db6 drivers/pinctrl/bcm/pinctrl-bcm2835.o
after:
text data bss dec hex filename
18764 8912 128 27804 6c9c drivers/pinctrl/bcm/pinctrl-bcm2835.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We get a warning during boot with enabled EARLY_PRINTK that
we try to set a irq_chip without data. This is caused by ignoring
the return value of irq_of_parse_and_map(). So avoid calling
gpiochip_set_chained_irqchip() in error case.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixups here tend to be more of a conglomerate of some of the other
repeated/systematic ones we've seen in the earlier pinctrl cleanups.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h
One driver has a .remove that would be dispatched on module_exit,
and as that code is essentially orphaned, so we remove it. In case
anyone was previously doing the (pointless) unbind to get to that
function, we disable unbind for this one driver as well.
A couple bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Eric Anholt <eric@anholt.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Sherman Yin <syin@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
